Catalytic activity of H-forms of zeolites in the isomerization of supercritical <Emphasis Type="Italic">n</Emphasis>-pentane and their physicochemical properties

The acidic properties of the H-forms of zeolites ZSM-5, Beta, Y, and mordenite are studied by diffuse reflectance IR spectroscopy using n-pentane as a probe molecule. The decreasing order of Brønsted acid site strengths is constructed. The isopentane selectivity in n-pentane isomerization under supercritical conditions (260°C, 130 atm) increases in the order H-ZSM-5 < H-Beta < H-mordenite(11) ≈ H-Y with decreasing strength of Brønsted sites. Catalytic data are analyzed jointly with the results of physicochemical studies of H-mordenite (temperature-programmed ammonia desorption, benzene adsorption, and IR spectroscopy). Under the supercritical conditions, the conversion of n-pentane on mordenite is determined by the total acidity of the zeolite and also by the accessibility of the acid sites inside the zeolite channels to the reactant.     

Nonoxidative conversion of methane and <Emphasis Type="Italic">n</Emphasis>-pentane over a platinum/alumina catalyst

Methane adsorption on the Pt–H/Al₂O₃ and Pt/Al₂O₃ catalysts begins at Т = 475°C and is accompanied by the appearance of hydrogen in the reaction medium. At a higher temperature is raised to 550°C, the amount of adsorbed hydrogen increases to 1.1 and 0.8 mol/(mol Pt), respectively. According to the calculated degree of methane dehydrogenation on platinum sites at Т = 550°C, the Н/C ratio is 1.3 (at/at) for the Pt–H/Al₂O₃ catalyst and 1.5 (at/at) for the Pt/Al₂O₃ catalyst. The introduction of n-pentane into the reaction medium increases the yield of aromatic hydrocarbons (benzene and toluene) by a factor of 8.8 over the arene yield observed in individual n-pentane conversion. A mass spectrometric analysis of the arenes obtained with the Pt/Al₂O₃ catalyst has demonstrated that 37.5% of the adsorbed methane is involved in the methane–n-pentane coaromatization yielding benzene and toluene.     

Effect of the structure of the <Emphasis Type="Italic">ortho</Emphasis>, <Emphasis Type="Italic">meta</Emphasis>, and <Emphasis Type="Italic">para</Emphasis> isomers of perhydroterphenyl on their reactivity in heterogeneous catalytic dehydrogenation

The kinetics of the dehydrogenation of the individual ortho, meta, and para isomers of perhydroterphenyl and their mixtures over a (3 wt % Pt)/C catalyst has been investigated in a flow reactor at 280–340°C. The rate of the isomerization of the stereoisomers of the initial substrate (perhydroterphenyl) and terphenyl dehydrogenation products has an effect on the hydrogen release kinetics. The highest reactivity in isomerization is shown by the ortho isomer. The largest amount of hydrogen (7.0 wt %) is released in the dehy-drogenation of perhydro-meta-terphenyl and perhydro-para-terphenyl, whose conversion at 320°C is 96%.     

Synthesis of silver(I) and palladium(II) <Emphasis Type="Italic">N</Emphasis>-heterocyclic carbene complexes and their use as catalysts for the direct C5 arylation of heteroaromatic compounds

Silver(I) N-heterocyclic carbene complexes were synthesized in good yields by the reactions of 1,3-dialkylperhydrobenzimidazolium salts with silver(I) oxide in dichloromethane. The silver complexes were used as carbene-transfer agents to synthesize palladium(II) N-heterocyclic carbene complexes. All of the complexes were characterized by physicochemical and spectroscopic methods. The new palladium complexes were tested as catalysts in the direct C5 arylation of 2-n-butylfuran, 2-n-butylthiophene and 2-n-propylthiazole with aryl bromides at 130 °C in N,N-dimethylacetamide. The arylation reactions proceeded selectively at the C5 position of the heteroaromatic compounds, and the corresponding coupling products were obtained in moderate to good yields by using 0.5 mol% of the palladium complex.     

Influence of sulfation conditions on the acidic and catalytic properties of sulfated alumina in isobutane alkylation with butylenes and <Emphasis Type="Italic">n</Emphasis>-pentane isomerization

The influence of the sulfation parameters (the source and concentration of sulfate ions) and the calcination temperature on the acidic and catalytic properties of sulfated alumina in the alkylation of isobutane with butylenes and n-pentane isomerization was studied. IR spectroscopy of adsorbed probe molecules and temperature-programmed desorption of ammonia were used to characterize the acidic properties of the catalysts. An increase in the content of sulfate groups to the value corresponding to a formal value of the monolayer capacity increases the activity of alkylation and the concentration of strong Brönsted sites. The dependence of the stability of activity in alkylation on the sulfate group concentration is extreme with a maximum at the concentration close to the monolayer capacity. It was concluded from the IR spectroscopic data that the decrease in the stability of activity with the further increase in the content of sulfate groups is due to an increase in the concentration of strong Lewis sites and/or an increase in the surface density of strong Brönsted sites. The absence of the correlation between the catalytic behavior of sulfated alumina samples in n-pentane isomerization and acidity indicates that paraffin activation on these samples occurs via the non-acidic mechanism.     

Effect of temperature on longevity of <Emphasis Type="Italic">Diaphorina citri</Emphasis> (Hemiptera: Liviidae) studied by microcalorimeter

The longevity of Asian citrus psyllid, Diaphorina citri, infected by an entomopathogenic fungus, Isaria fumosorosea, was studied by microcalorimetry. Experimental results of microcalorimetry suggest that in the process of metabolism of D. citri heat or heat flow declined exponentially. The metabolism of D. citri inhibited by increasing temperature, and the longevity of D. citri decreased gradually with respect to temperature. The longevity of D. citri almost reaches 500 h at 25 °C and D. citri died within 130 h at 41 °C under high-temperature exposure. The same phenomenon, decrease in longevity and metabolism inhibition, was observed under the low-temperature exposure. The supercooling point of insects can be derived from a cooling curve plotting the temperature versus time by using microcalorimetry. The heat released due to phase change can be determined by using microcalorimeter. Our results indicated that microcalorimetry can be used to measure the metabolism of herbivore insects.     

Effect of phosphate doping on electric properties and chemical stability of Ba<Subscript>4</Subscript>Ca<Subscript>2</Subscript>Nb<Subscript>2</Subscript>O<Subscript>11</Subscript> protonic conductor

Conductivity of perovskite phosphate–substituted solid solutions of Ba₄Ca₂Nb_{2 –x} P _x O₁₁ (0.0 ≤ x ≤ 0.5) was studied as a function of temperature, partial pressure of oxygen and water vapors. It is proved that the studied systems are protonic conductors at the temperatures below 600°C in the atmosphere with elevated content of water vapors (pH₂O = 1.92 × 10^–2 atm). Introduction of the tetrahedral [PO₄] group in the complex oxide matrix of Ba₄Ca₂Nb₂O₁₁ results in an increase in the oxygen–ionic (dry air, pH₂O = 1.91 × 10^–4 atm) and protonic conductivities (wet air, pH₂O = 1.92 × 10^–2 atm). Is it found that the doping causes a considerable increase in chemical stability of phases with respect to carbon dioxide.     

The inductive effect of a radical center and transferability of the properties of functional groups in <Emphasis Type="Italic">n</Emphasis>-alkyl radicals

Electron density distribution in n-alkyl radicals (from ethyl to n-octyl) was studied by the B3LYP/6-311++G(3df,3pd) DFT method. The theory of atoms in molecules was used to show that the inductive effect of a free valence extends to two neighboring CH₂ groups. The electronegativities χ(C^?H₂) > χ(CH₃) > χ(CH₂) of groups and χ(C^?) > χ(H) > χ(C) atoms were qualitatively determined. The group method for calculating the enthalpies of formation of n-alkyl radicals Δ_f H°(n-C _n H_{2n+ 1}, n > 5) was substantiated.     

X-ray diffraction study of CsZn<Subscript>2</Subscript>Br<Subscript>5</Subscript>

CsZn₂Br₅ crystals are studied by X-ray diffraction. The compound crystallizes in the monoclinic system with the unit cell parameters a = 6.8880(12) Å, b = 10.4703(19) Å, c = 6.5197(9) Å, β = 108.25°, V = 446.55 ų, ρ_calcd = 4.960 g/cm³. Refractive indices are n _p = 1.640 and n _p = 1.754.     

The first cubane-like complex of copper based on <Emphasis Type="Italic">N</Emphasis>-carboxyethyl-tris(hydroxymethyl)aminomethane: Synthesis and crystal structure

The interaction of acrylic acid with tris(hydroxymethyl)aminomethane (I) was studied. A simple method was suggested for preparing N-carboxyethyl-tris(hydroxymethyl)aminomethane (homotricin) (II). On the basis of compound II, the 1:1 Cu complex, [Cu(OCH₂C(CH₂OH)₂NHCH₂CH₂COO)]₄·nH₂O (n = 4–11.25) (III), which is alkoxycarboxylate, was synthesized. The crystal structure of III was found to correspond to a cubane-like tetranuclear cluster (an automated Bruker X8Apex diffractometer with CCD detector (MoK _α radiation, graphite monochromator, ? = 1.11°?27.5°), 8016 reflections, space group P \(\overline 1 \), a = 12.5573(3), b = 19.1012(4), c = 21.2903(5) Å, α = 80.7770(10)°, β = 75.7430(10)°, γ = 75.2260(10)°, V = 4761.62(19) ų, ρ(calcd.) = 1.704 g/cm³, Z = 4). The crystals are unstable due to the large number of water molecules.     

Thermal Rearrangements of 3<Emphasis Type="Italic">H</Emphasis>- and 4<Emphasis Type="Italic">H</Emphasis>-Pyrazoles Prepared by Reactions of 9-Diazofluoren with Methyl Tetrolate and Methyl 3-Phenylpropiolate

9-Diazofluoren adds in Et₂O at 20°C to methyltetrolate in keeping with Auwers rule and nonregioselectively adds to methyl-3-phenylpropiolate with the formation of spirocyclic 3H-pyrazoles. The methyltetrolate adduct at boiling in toluene converts into methyl 3a-methyl-3aH-dibenzo[e,g]indazole-3-carboxylate, at 190°C in benzene, into methyl 3-methyl-2H-dibenzo[e,g]indazole-2-carboxylate, and at 160°C in methanol, into 3-methyl-2H-dibenzo[e,g]indazole. Auwers adduct of methyl 3-phenylpropiolate at boiling in benzene gives cyclopropene derivative and at boiling in methanol isomerizes into methyl 3a-phenyl-3aHdibenzo[e,g]indazole-3-carboxylate. Anti-Auwers adduct at boiling in benzene isomerizes into methyl 2-phenylpyrazolo[1,5-f]phenanthridine-3-carboxylate.     

Potential functions of internal rotation in <Emphasis Type="Italic">n</Emphasis>-alkanes and its contribution to thermodynamic properties

The potential functions of braked internal rotation V(?) in n-alkanes (ethane, propane, butane, n-pentane, n-hexane, n-heptane) were calculated by ab initio and DFT methods with the 6-311++G(3df,3pd) basis set. The functions were approximated as a series of six cosines. The dependences of V(?) on the length of the hydrocarbon chain in n-alkanes were analyzed. The heights of the trans-cis and trans-gauche barriers and the differences between the energies of the trans and gauche conformers were calculated and compared with the experimental data. From the calculated geometric parameters and V(?), the contributions of the braked internal rotation to the enthalpy, entropy, heat capacity, and Gibbs free energy at 298 K were determined. The contributions of internal rotations are transferable within the framework of additive approaches. The generalized function V _av(?) for n-alkanes and averaged contributions of internal rotation of the C-C bonds and CH₃- and -CH₂- tops to the thermodynamic properties were suggested.     

Oligomerization of <Emphasis Type="Italic">N</Emphasis>-vinylpyrroles under the action of iodine

The oligomerization of N-vinylpyrroles (N-vinyl-4,5,6,7-tetrahydroindole, N-vinyl-2-[1-(1-4,5,6,7-tetrahydroindole)ethyl]-4,5,6,7-tetrahydroindole, N-vinyl-2-phenylpyrrole, N-vinyl-3-heptyl-2-phenylpyrrole, N-vinyl-2,3-diphenylpyrrole, and N-vinyl-2-(2-naphthyl)pyrrole) under the action of iodine vapor leads to the formation of iodine-containing oligomers with an iodine content of 17–52% and a yield of up to 99%. The oligomers are paramagnetic and possess conductivity; they are readily soluble in organic solvents (benzene, dioxane, and chloroform) and are stable up to 110–260°C.     

Synthesis and structure of silicon-containing <Emphasis Type="Italic">N</Emphasis>-methyland <Emphasis Type="Italic">N</Emphasis>-benzoylamides of diisopropylphosphoric acid

Diisopropyl N-benzoyl-N-(trimethylsilyl)phosphoramidate reacts with ClCH₂SiMe₂Cl under mild conditions to form diisopropyl N-benzoyl-N-[(chlorodimethylsilyl)methyl]phosphoramidate (III). Diisopropyl N-methyl-N-(trimethylsilyl)phosphoramidate with ClCH₂SiMe₂Cl affords an N-transsilylation product which does not rearrange into diisopropyl N-[(chlorodimethylsilyl)methyl]-N-methylphosphoramidate (XV) even under severe conditions (4 h, 130°C). Compound XV was prepared by the reaction of diisopropyl phosphorochloridate with N-[(methoxydimethylsilyl)methyl]-N-methylamine followed by treatment of diisopropyl N-[(methoxydimethylsilyl)methyl]-N-methylphosphoramidate with boron trichloride. Analysis of experimental and calculated ²⁹Si chemical shifts points to a five-coordinate silicon atom in compound III and a fourcoordinate silicon atom in compound XV. According to B3LYP calculations with due regard to solvent effects, compound III is an isomer with a C=O→Si bond. By variation of substituents at silicon, phosphorus, and carbonyl carbon atoms, chelate structures with either C=O→Si or P=O→Si dative bonds can be obtained.     

Exchange reactions of urethanes with proton-donating compounds: Kinetics of the reactions of phenyl-<Emphasis Type="Italic">N</Emphasis>-phenylurethane with butyl alcohols

The exchange reactions of phenyl-N-phenylurethane with aliphatic alcohols, namely, n-butyl, sec-butyl, and tert-butyl alcohols, in ortho-dichlorobenzene and in the media of the corresponding alcohols were studied. In the absence of a catalyst and proton-donating compounds, the monomolecular cleavage of phenyl-N-phenylurethane to isocyanate and alcohol proceeds at a noticeable rate starting only at 250°C. Between 40 and 80°C, the exchange reactions take place via direct exchange between urethane and the photon-donating compound and are second-order up to high conversions (until the almost complete disappearance of the initial urethane). Activation energies and apparent rate constants have been determined for the exchange reactions of phenyl-N-phenylurethane with butyl alcohols. The rates of the exchange reactions in the alcohol medium are compared with those in ortho-dichlorobenzene.     

Phase composition,formation parameters,and morphology of precipitates in the LiVO<Subscript>4</Subscript>-VOSO<Subscript>4</Subscript>-H<Subscript>2</Subscript>O system

The phase and chemical compositions of the precipitates formed in the LiVO₃-VOSO₄-H₂O system at initial pH within 1 ≤ pH ≤ 4 and 90°C were studied. The following phases were prepared: an α phase Li_1.4(VO)_1.3[H₂V₁₀O₂₈] · nH₂O and a β phase Li_{0.6 ? x} H_{1.4 + x} [V₁₂O_{31 ? y/2}] · nH₂O (0 ≤ x ≤ 0.5, 1.3 ≤ y ≤ 2.0) with a layered structure. Li_0.4V₂O₅ · H₂O nanorods with the interlayer distance 10.30 ± 0.08 Å were synthesized at 180°C in an autoclave. The morphology, IR spectra, and main formation processes for these polyvanadates were studied.     

Synthesis of Block Copolymers of Styrene with <Emphasis Type="Italic">D</Emphasis>,<Emphasis Type="Italic">L</Emphasis>-Lactide by the Sequential Controlled Cationic Polymerization and Ring-Opening Anionic Polymerization

The cationic polymerization of styrene initiated by the system 2-chloro-2-phenylpropane–TiCl₄–pyridine is studied in a mixture CH₂Cl₂–n-hexane at a temperature of –80°С. It is shown that under these conditions polymerization occurs via the living mechanism at [monomer]: [initiator] ≤ 100. The method of preparing polystyrenes with terminal primary hydroxyl groups (M_n = 4000–10000 g/mol) by the sequential controlled cationic polymerization of styrene and the in situ alkylation of 4-phenoxy-1-butanol by polystyrene macrocations is proposed. The resulting functionalized polystyrenes are used as macroinitiators of anionic-coordination ring-opening polymerization of D,L-lactide in the presence of tin bis(2-ethyl hexanoate) [Sn(Oct)₂] in toluene at 80°С. Copolymers polystyrene-block-poly(D,L-lactide) with the controlled length of the poly(D,L-lactide) block (M_n = 10000–17000 g/mol) and a relatively low molecular-weight distribution (M_w/M_n = 1.6–1.8) are synthesized. Formation of the block copolymers is confirmed by ¹Н NMR spectroscopy, gel-permeation chromatography, and atomic force microscopy.     

Hydrogenation of biphenyl and isomeric terphenyls over a Pt-containing catalyst

Catalytic hydrogenation of benzene, biphenyl, and ortho-, metha-, and para-isomers of terphenyl over a 3 wt.% Pt/C at 180 °C and 70 atm was studied. The directions of hydrogenation of each substrate were revealed. Relationships between structures of the substrate and hydrogen consumption rates were found. It was shown that hydrogenation rate decreases on going from benzene to terphenyl and with increasing degree of the substrate hydrogenation. Hydrogenation rate of terphenyl isomers decreases in the following order: p-terphenyl > > m-terphenyl > o-terphenyl.     

Synthesis and crystal structure of two complexes [Cu<Subscript>2</Subscript>(NiL)<Subscript>2</Subscript>Cl<Subscript>4</Subscript>] and [Cd<Subscript>2</Subscript>(CuL)<Subscript>2</Subscript>Cl<Subscript>4</Subscript>]

Macrocyclic and supermolecular complexes [Cu₂(NiL)₂Cl₄] (I) and [Cd₂(CuL)₂Cl₄] (II) (H₂L = 2,3-dioxo-5,6,14,15-dibenzo-1,4,8,12-tetraazacyclo-pentadeca-7,13-diene) have been synthesized and structurally determined by X-ray diffraction and IR spectrum. Complex I crystallizes in the monoclinic system with P2₁/n group, a = 10.9019(15), b = 14.3589(19), c = 12.4748(17) 0A, β = 108.645(2)°, Z = 4. Complex II crystallizes in the monoclinic system with P2₁/n group, a = 10.9784(16), b = 14.580(2), c = 12.8904(18) Å, β = 109.339(2)°, Z = 4.     

Prereforming of <Emphasis Type="Italic">n</Emphasis>-tetradecane over Ce-promoted 50 wt% Ni/MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst with high coke resistance

The effect of Ce-promotion on 50 wt% Ni-based catalysts during the prereforming of n-tetradecane and its optimum content were investigated. The Ni catalyst was synthesized by deposition–precipitation method. Next, various amounts of Ce (0–13 wt%) were loaded on the Ni catalyst by impregnation. The characteristics of the prepared catalysts were analyzed by XRD, H₂-TPR, BET, BJH, and H₂-chemisorption analyses. The prepared catalysts were tested under the prereforming conditions (temperature = 400 °C, GHSV = 3000 h^?1, and S/C = 3 and 4). The Ni catalyst was easily deactivated under the following conditions: temperature = 400 °C, GHSV = 3000 h^?1, and S/C = 4. The stability of all Ce-promoted Ni catalysts was improved as compared to that of the Ni catalyst. Among the Ce-promoted catalysts, 5 wt% Ce/50 wt% Ni/MgO–Al₂O₃ catalyst showed excellent stability even under the severe condition of S/C = 3. SEM, TEM, and TG analyses were performed in order to identify the main factor responsible for the rapid deactivation of the Ni catalyst. In the case of 0Ce/50Ni, Ni particles were encapsulated by many folds of coke and it was related to the rapid catalyst deactivation. However, after Ce promoted on the Ni catalyst, the thickness of the coke layers and the number of encapsulated Ni particles decreased and the deposited amount of coke on the catalyst also decreased.