Adsorption of polymers at the solution-solid interface

Summary The adsorption of ethylene-vinyl acetate copolymer which consists of two different adsorption energy segments from solution onto glass sphere was studied. The adsorption depends on molecular weight and the constant obtained by application ofUllman's equation is decreased with the increase of molecular weight. The molecular weight dependence of adsorption suggests that the polymer chain adsorbed at solution-solid interface consist of sequences and loop chains. The relation between maximum adsorption and area occupied with adsorbed polymer chain from various solution was discussed, and the solvent dependence of maximum adsorption was explained in the difference of polymer solubility.

---

Zusammenfassung Die Adsorption von Äthylen-Vinylacetat-Copolymeren, die aus zwei unterschiedlichen Segmenten hinsichtlich der Adsorptionsenergie bestehen, aus der Lösung an Glaskugeln wurde untersucht. Die Adsorption hängt vom Molekulargewicht ab; und die Konstante , erhalten durch Anwendung derUllmanschen Gleichung, nimmt mit der Zunahme des Molekulargewichts ab. Die Molekulargewichts-Abhängigkeit der Adsorption läßt vermuten, daß die Polymerketten, in der Grenzfläche adsorbiert, aus Sequenzen und Schleifen bestehen. Die Beziehungen zwischen maximaler Adsorption und mit adsorbierter Polymerketten besetzter Fläche aus verschiedener Lösung wird diskutiert und die Lösungsmittel-Abhängigkeit der maximalen Adsorption wurde aus dem Unterschied der Polymer-Löslichkeit erklärt.

---

---

With 7 figures and 3 tables     

Adsorption of toluene-soluble polymers at the toluene–water interface

The adsorption of several toluene-soluble polymers at the toluene–water interface has been investigated by using the duNouy ring method of measuring interfacial tension γT /W . Polystyrene and poly(ethylene-co-vinyl acetate) (11.1 mole-% vinyl acetate) have little affinity for this interface at 29°C, but poly(methyl methacrylate) (PMMA) (M?_n = 420,000) and ethyl cellulose (EC) (M?_n = 50,100; 49.1% ethoxyl) adsorb significantly at concentrations as low as 1.0 × 10^?4 g/100ml. A plot of interfacial tension lowering versus initial logarithm of initial bulk phase polymer concentration is linear from 1.0 × 10^?4 to 1.0 × 10^?1 g/100 ml for EC and 1.0 × 10^?4 to 1.0 × 10^?2 g/100 ml for PMMA. When the PMMA concentration increases to 1.15 × 10^?1 g/100 ml, its adsorption behavior changes markedly. Prolonged time effects occur and adsorption becomes dependent upon dissolved water content of the toluene prior to formation of the toluene/water interface. Such effects are not observed with the other solutions studied. Increasing temperatures have variable effects on values of γT /W for the polymer solutions studied. Experiments with various polymer mixtures indicate that the polymer lowering T /W the most is preferentially adsorbed at the toluene–water interface and rapidly displaces less strongly adsorbed polymers.     

Adsorption of ionic surfactants at an expanding air-water interface

A quantitative model for the kinetics of adsorption of ionic surfactants to an expanding liquid surface is presented for surfactant concentrations below and above the critical micelle concentration (cmc). For surfactant concentrations below the cmc, the electrostatic double layer is accounted for explicitly in the adsorption isotherm. An overflowing cylinder (OFC) was used to create nonequilibrium liquid surfaces under steady-state conditions. Experimental measurements of the surface excess for solutions of cationic surfactants CH3(CH2)n-1N+(CH3)3 Br- (CnTAB, n = 12, 14, 16) and the anionic fluorocarbon surfactant sodium bis(1H,1H-nonafluoropentyl)-2-sulfosuccinate (di-CF4) in the OFC are in excellent agreement with the theoretical predictions for diffusion-controlled adsorption for all concentrations studied below the cmc. For surfactant concentrations above cmc, the diffusion ofmicelles and monomers are handled separately under the assumption of fast micellar breakdown. This simplified model gives excellent agreement for the system C14TAB + 0.1 M NaBr above the cmc. Agreement between theory and experiment for C16TAB + 0.1 M NaBr is less good. A plausible explanation for the discrepancy is that micellar breakdown is no longer fast on the time scale of the OFC (ca. 0.1 s).     

Adsorption of polymers at the solution-solid interface. VI. Polyacids on nylon powder

The adsorption of some polyacids, principally poly(acrylic acid), on nylon powder has been studied. In aqueous solutions at low pH the adsorption behavior of poly(acrylic acid) is controlled by adsorbate coil dimensions rather than by electrostatic effects. Less adsorption takes place from methanol solutions but the process is much more rapid than from water. Above a critical value, increase of adsorbate molecular weight leads to a reduced adsorption, the effect being particularly evidenced by aqueous solutions. Model compounds (propionic and glutaric acids) are rapidly adsorbed from both methanol and water, but give low specific absorptions. Adsorption of poly(acrylic acids) and model compounds, is reduced, but not eliminated, by modification of the nylon adsorbent through acetylation or methoxymethylation. The adsorption of poly(acrylic acid) on nylon is not readily reversible; however, partial neutralization will release preadsorbed poly(acrylic acid) from nylon powder. The adsorption behavior of copolymers of acrylic acid with N-vinylpyrrolidone is reported, as are brief studies on some other homopolyacids. The results are generally interpreted on the basis of sorption of the macromolecules into a swollen, flexible adsorbent.     

Adsorption kinetics of NIPAM-based polymers at the air-water interface as studied by pendant drop and bubble tensiometry

The adsorption of N-isopropylacrylamide (NIPAM) based thermoresponsive polymers at the air-water interface was investigated by using drop and bubble shape tensiometry. The molecular weight dependence of polymer adsorption rate was studied by using narrowly distributed polymer fractions (polydispersity < 1.2) that were prepared by solvent:nonsolvent fractionation. The time-dependent surface tension profiles were fitted to the Hua-Rosen equation and the t values obtained were applied for interpretation of the kinetic data. It was found that the rate of polymer adsorption increased as the molecular weight of the polymer decreased. The relationship between polymer surface concentration and surface tension was determined by applying the pendant drop as a Langmuir-type film balance. From this relationship, the kinetics of polymer adsorption determined experimentally was compared with the adsorption rates predicted by a diffusion-controlled adsorption model based on the Ward-Tordai equation. The predicted adsorption rates were in good agreement with what was found experimentally. The dependence of the adsorption rate on the molecular weight of polymers can be satisfactorily described within the diffusion-controlled model.     

Low band-gap oligomers and polymers

The relationship between electronic structure and chemical stability is discussed for three different classes of low band-gap oligomers and polymers. In oligo- and poly[n]acenes as well as in poly-(arylenemethide)s, the low band-gap character is connected with a high chemical reactivity due to an energetically favored rearomatization of olefinic or quinonoid substructures, respectively. For double-stranded oligo- and poly(rylene)s, the stability is dramatically increased. Therefore, rylenes appear especially promising in the field of low band-gap materials.     

Adsorption of polymers at the solution-solid interfaces

Summary Adsorption of ethyl cellulose, so-called rigid polymer, on the glass surface from various solvents having no groups to make the hydrogen bonds with solid surface was carried out. And the solvent dependence was found. The dependence is, however, small as compared with polyvinyl acetate-glass system (1). A main factor to control the solvent dependence is not competitive between solvent and polymer, but the effect of solvent to extension of polymer in solution, that is, segment density per solid surface area in poor solvent is greater than in better solvent. Maximum adsorption is independent of molecular weight of ethyl cellulose used (Mv=2×10⁴6×10⁴). It is expected that ethyl cellulose lies flat on the glass surface considering adsorption energy per segment (₀>5kT).

---

Zusammenfassung Adsorptionen von Äthylzellulose als sozusagen steifes Polymeres an Glasoberfläche aus verschiedenen Lösungsmitteln heraus, die keine Gruppen für Wasserstoff bindungen an die Festoberflächen besitzen, wurden ausgeführt. Es ergab sich in der Tat Lösungsmittelabhängigkeit. Diese ist jedoch klein im Vergleich zu der beim System Polyvinylacetat/Glas. Eine Ursache für die Lösungsmittelabhängigkeit ist nicht direkt die unterschiedliche Solvatation zwischen Lösung und Polymer, sondern der Effekt des Lösungsmittels auf die räumliche Aufweitung des Polymers in Lösungen. Letzteres bedeutet nämlich, die Segmentdichte ist in schlechten Lösungsmitteln größer als in guten. Die maximale Adsorption ist unabhängig vom Molekulargewicht im Bereich vonMv=2×10⁴ bis 6×10⁴. Es ist zu erwarten, daß die Äthylzellulosc flach auf der Glasoberfläche aufliegt, wenn man die Adsorptionsenergie pro Segment betrachtet.

---

---

With 5 figures and 4 tables     

Adsorption of nanoparticles at the solid-liquid interface

The adsorption of differently charged nanoparticles at liquid-solid interfaces was investigated by in situ X-ray reflectivity measurements. The layer formation of positively charged maghemite (γ-Fe(2)O(3)) nanoparticles at the aqueous solution-SiO(2) interface was observed while negatively charged gold nanoparticles show no adsorption at this interface. Thus, the electrostatic interaction between the particles and the charged surface was determined as the driving force for the adsorption process. The data analysis shows that a logarithmic particle size distribution describes the density profile of the thin adsorbed maghemite layer. The size distribution in the nanoparticle solution determined by small angle X-ray scattering shows an average particle size which is similar to that found for the adsorbed film. The formed magehemite film exhibits a rather high stability.     

Adsorption characteristics of polyvinylpyrrolidone at solid-liquid interface

Summary Adsorption studies of polyvinylpyrrolidone (PVP) on the surface of colloidal silicas, Aerosil 300 and Aerosil R-972 are reported. The adsorption isotherms of PVP at the hydrophilic silica/aqueous solution interface were greater than that at the hydrophobic silica R-972. The PVP adsorption shows that the amount adsorbed decreases with the concentration.The isotherms contain a minimum when water is used as the solvent. The minimum disappears when Na₂SO₄ 0.55 M is used as the solvent. The PVP adsorption behavior could be due to a different adsorption rate of the various molecular species of the fractions. The orientation of macromolecules adsorbed on the surface would depend on the polymer-solvent interaction in solution. The adsorption would be governed by the surface structural characteristics and would be a function of the molecular weight of the polymer depending on the macromoleculer orientation within the interface.

---

Zusammenfassung Es wird über Adsorption von Polyvinylpyrrolidone (PVP) an der Oberfläche der Kieselgele Aerosil 300 and Aerosil R-972 berichtet. Die Adsorptionsisothermen von PVP auf der hydrophilen Kieselgel/Wasserlösungs-Grenzphase erwiesen sich als größer als die auf dem hydrophoben Kieselgel R-972. Die adsorbierte Menge nimmt mit der Konzentration ab. Die Isothermen zeigen ein Minimum, wenn Wasser als Lösungsmittel benutzt wird. Das Minimum verschwindet, wenn eine 0.55M wäßrige Natriumsulphat-Lösung verwendet wird. Das Adsorptionsverhalten des PVP könnte auf einer verschiedenen Adsorptionsgeschwindigkeit für die verschiedenen molekularen Spezies in den Fraktionen beruhen. Die Orientierung von den an der Oberfläche adsorbierten Makromolekülen würde von der Wechselwirkung zwischen Polymer und Lösungsmittel in der Lösung abhängen. Die Adsorption wurde von den strukturellen Eigenschaften der Oberfläche beherrscht werden und eine Funktion des Molekulargewichtes des Polymers sein, abhängig von der Orientierung der Makromoleküle in der Grenzphase.

---

---

With 4 figures and 1 table     

Adsorption of 1,4 polyisoprene at solid-liquid interface

The adsorption of trans 1,4 polyisoprene was studied on alumina and silica gel at four temperatures. The solvents were cyclohexane, toluene, and 1:1 mixture of the two. The adsorption was found to decrease from cyclohexane >toluene >mixed solvent. The amount of adsorption was an inverse function of temperature. For almost all the systems, the adsorption isotherms were of Langmuir type, though solvent characteristic seems to be a more dominating factor than adsorbent in determining the shape of the isotherm.     

Adsorption of cinnamaldehyde at the mercury-water interface

The adsorption of cinnamaldehyde from aqueous 1 M KCl has been determined by means of differential capacity, zero charge potential and maximum surface tension measurements. A Frumkin isotherm is obeyed with α = 2.4, corresponding to repulsive interaction, and Γ_s= 3.5 × 10^?10 mol cm^?2, which is independent of potential in the range ?350/?750 mV. The standard free energy of adsorption is a quadratic function of potential with maximum adsorption occurring at the potential of zero charge. The interaction of the molecular dipole with the electric field and the partial charge transfer between the electrode and the adsorbate are considered.     

Adsorption of polymers at the solution–solid interface. XIV. Adsorption and steric stabilization with styrene–acrylonitrile copolymers

The adsorption of random copolymers of styrene and acrylonitrile of azeotropic composition from their trichloroethylene solutions onto precipitated silica exhibits a maximum at intermediate molecular weights. These copolymers are able to stabilize dispersions of some, but not all, grades of precipitated silica; here, too, a maximum effect is found at intermediate molecular weights. Copolymers are partially desorbed by ethyl cyanide, which destabilizes silica dispersions. Block copolymers of low acrylonitrile contents do not stabilize well but, when preadsorbed, affect the behavior of subsequently adsorbed random copolymers. In particular, high molecular weight random copolymers flocculate the pretreated silica; silica with grafted polyacrylonitrile chains may also be flocculated by these copolymers.     

Phenylethynyl-terminated imide oligomers and polymers therefrom

Two new phenylethynyl endcapping compounds, 3- and 4-amino-4′-phenylethynylbenzophenone, were synthesized and used to terminate imide oligomers from 3,4′-oxydianiline and 4,4′-oxydiphthalic anhydride at a calculated molecular weight of 9000 g/mol and from 3,4′-oxydianiline (0.85 mol), 1,3-bis (3-aminophenoxy) benzene (0.15 mol), and 3,3′,4,4′-biphenyltetracarboxylic dianhydride at a calculated molecular weight of 5000 g/mol. Glass transition temperatures for the cured oligomers were ～ 249°C for the former and 272°C for the latter. Films cured at 350°C for 1 h were tough and flexible and provided high tensile properties. The uncured oligomers were readily compression molded to provide tough, solve nt-resistant moldings. © 1994 John Wiley & Sons, Inc.     

Adsorption studies of dodecylamine at the quartz interface using an electrode-separated piezoelectric sensor

The adsorption process of dodecylammonium chloride (DAC) from aqueous solutions onto a quartz crystal interface was investigated in situ using an electrode-separated piezoelectric sensor (ESPS). Increasing amounts of DAC adsorbed onto a quartz crystal surface resulted in linearly decreasing oscillating frequencies of the ESPS. The adsorption density can be monitored by the frequency decrease. The adsorption density obtained by calculation using the Sauerbrey equation in the ESPS method is greater than that in solution depletion method. A calibration coefficient is added into the Sauerbrey equation to correct the influence of surface roughness of the quartz crystal on the adsorption density. The influence of solution properties on the adsorption density measurement was discussed. A dependence of the adsorption density on pH was reported. Received: 17 April 1997 / Revised: 1 December 1997 / Accepted: 7 December 1997     

Adsorption studies of dodecylamine at the quartz interface using an electrode-separated piezoelectric sensor

The adsorption process of dodecylammonium chloride (DAC) from aqueous solutions onto a quartz crystal interface was investigated in situ using an electrode-separated piezoelectric sensor (ESPS). Increasing amounts of DAC adsorbed onto a quartz crystal surface resulted in linearly decreasing oscillating frequencies of the ESPS. The adsorption density can be monitored by the frequency decrease. The adsorption density obtained by calculation using the Sauerbrey equation in the ESPS method is greater than that in solution depletion method. A calibration coefficient is added into the Sauerbrey equation to correct the influence of surface roughness of the quartz crystal on the adsorption density. The influence of solution properties on the adsorption density measurement was discussed. A dependence of the adsorption density on pH was reported. Received: 17 April 1997 / Revised: 1 December 1997 / Accepted: 7 December 1997     

Adsorption of polymers at the solution–solid interface. XIII. Adsorption and steric stabilization with styrene–2-vinylpyridine copolymers

Random and block copolymers of styrene and 2-vinylpyridine, covering the full range of composition, have been synthesized. The adsorption of these polymers from trichloroethylene solution on to precipitated silica has been studied and their ability to impart colloidal stability to the silica dispersions also investigated. Estimates of the layer thickness of adsorbed copolymers have been made. Polystyrene is not adsorbed from trichloroethylene and does not stabilize dispersions of precipitated silica. A random copolymer having 1% 2-vinylpyridine units is adsorbed but shows very little steric stabilization. Random copolymers of 2-vinylpyridine content greater than 10% and AB block copolymers of more than 6% 2-vinylpyridine behave very similarly in respect both of the quantity adsorbed and in their ability to stabilize silica suspensions. Layer thickness does not seem to depend on copolymer composition. Random copolymers with low to intermediate 2-vinylpyridine contents are better steric stabilizers in trichloroethylene than are the corresponding copolymers of methyl methacrylate with styrene: this is attributed in part to the longer sequences of adsorbable units in the vinylpyridine copolymers.     

Crystalline self-assembly into monolayers of folded oligomers at the air-water interface

Insertion of the 1,3-bis(ethynylene)benzene unit as a rigid spacer into a linear alkyl chain, thus separating the two resulting stems by 9 A. induces chain folding at the air-water interface. These folded molecules self-assemble into crystalline monolayers at this interface, with the plane of the folding unit almost perpendicular to the water surface, as determined by synchrotron grazing-incidence X-ray diffraction. Three distinct molecular shapes, of the types U, inverted U, and M, were obtained in the two-dimensional crystalline state, depending upon the number of spacer units, and the number and position of the hydrophilic groups in the molecule. The molecules form ribbons with a higher crystal coherence in the direction of stacking between the molecular ribbons, and a lower coherence along the ribbon direction. A similar molecule, but with a spacer unit that imposes a 5 A separation between alkyl chains, yields the conventional herringbone arrangement.