The plumber's nightmare: a new morphology in block copolymer-ceramic nanocomposites and mesoporous aluminosilicates

A novel cubic bicontinuous morphology is found in polymer-ceramic nanocomposites and mesoporous aluminosilicates that are derived by an amphiphilic diblock copolymer, poly(isoprene-b-ethylene oxide) (PI-b-PEO), used as a structure-directing agent for an inorganic aluminosilicate. Small-angle X-ray scattering (SAXS) was employed to unambiguously identify the Im(-)3m crystallographic symmetry of the materials by fitting individual Bragg peak positions in the two-dimensional X-ray images. Structure factor calculations, in conjunction with results from transmission electron microscopy, were used to narrow the range of possible structures consistent with the symmetry and showed the plumber's nightmare morphology to be consistent with the data. The samples are made by deposition onto a substrate that imposes a strain field, generating a lattice distortion. This distortion is quantitatively analyzed and shown to have resulted in shrinkage of the crystallites by approximately one-third in a direction perpendicular to the substrate, in both as-made composites and calcined ceramic materials. Finally, the observation of the bicontinuous block-copolymer-derived hybrid morphology is discussed in the context of a pseudo-ternary morphology diagram and compared to existing studies of ternary phase diagrams of amphiphiles in a mixture of two solvents. The calcined mesoporous materials have potential applications in the fields of catalysis, separation technology, and microelectronics.     

Charge separation in mesoporous aluminosilicates

EPR spectroscopy has been used to investigate spontaneous and/or photo-induced electron transfer between adsorbed organic molecules and the mesoporous aluminosilicate MCM-41 host. Spontaneous electron transfer occurs from the host to electron acceptor molecules with sufficiently favourable reduction potentials (TCNE, TCNQ, 1,4-benzoquinone, 1,4-naphthaquinone and 1,4-anthraquinone), provided the MCM-41 contains aluminium and the radical anion yield correlates with the aluminium content of the host. The semiquinone radical anions are interacting strongly with exposed Al³⁺ sites, whereas the TCNE and TCNQ radical anions are loosely bound and can be washed from the host. Radical cation formation is observed when electron donor molecules with favourable oxidation potentials are adsorbed in MCM-41 containing aluminium, and the radical cations formed interact with exposed Al³⁺ sites. This work shows that aluminium-containing MCM-41 contains both electron donating and electron accepting sites which may intervene in intra-molecular charge separation processes in adsorbed organic molecules.     

Hydrogenation of naphthalene on noble-metal-containing mesoporous MCM-41 aluminosilicates

Aromatic saturation of oil fractions is a key process in the refining industry due to increasing demand for cleanest distillates with superior performances. In this study, the behavior of different catalysts containing 1 wt.% of noble-metal inside a mesoporous MCM-41 (Si:Al=20) framework was investigated in the hydrogenation of naphthalene, as preliminary step to investigate bimetallic catalysts. While at atmospheric pressure only Rh and Pd showed a low hydrogenation activity, in the tests performed at 6.0 MPa the catalytic activity grew, exhibiting the following order: Pt>RhPd>>>Ru≈Ir. However, all the catalysts required a large H₂ excess, to avoid a decrease in hydrogenation and ring-opening activity, and gave rise to the best performance for a contact time of 6.8 s, favouring at lower values the partial hydrogenation to tetralin and at higher values cracking reactions. Finally, all the catalysts showed low thio-tolerance, with significant deactivation already feeding 100 ppm wt. of dibenzothiophene (DBT), with a partial reversibility only for the Pt-containing catalyst (CAT 3).     

Adsorptive desulfurization of diesel with mesoporous aluminosilicates

Mesoporous aluminosilicates (MAS) bearing microporous zeolite units and mesoporous structures were synthesized by the hydrothermal method. Adsorptive desulfurization ability of model oil and hydrotreated diesel was studied. The effects of template concentration, crystalization time and calcination time were investigated. The desulfurization ability of adsorbents was improved by transitional metal ion-exchanging. The adsorptive desulfurization of diesel was carried out on a fixed-bed system. The results show that the adsorptive capacity is MAS>MCM-41>NaY. The improvement of desulfurization ability of MAS by Cu⁺ is more significant than that of Ag⁺. Supported by National Basic Research Program of China (Grant No. 2006CB202507), National High-tech R&D Program (Grant No. 2006AA02Z209), and the National Natural Science Foundation of China (Grant No. 20806086)     

Properties of mesoporous aluminosilicates prepared with nonionic surfactants

Mesoporous aluminosilicates with specific surface area up to 1030 m²/g and pore diameters from 33 to 43 Å were obtained using hexadecylamine and block copolymers of polyethylene and polypropylene oxides as structural directing agents. The synthesized materials were tested in catalytic cracking of hydrotreated vacuum gas oil at 500°C.     

One-step synthesis of hydrothermally stable mesoporous aluminosilicates with strong acidity

Using tetraethylorthosilicate (TEOS), polymethylhydrosiloxane (PMHS) and aluminium isopropoxide (AIP) as the reactants, through a one-step nonsurfactant route based on PMHS-TEOS-AIP co-polycondensation, hydrothermally stable mesoporous aluminosilicates with different Si/Al molar ratios were successfully prepared. All samples exclusively showed narrow pore size distribution centered at 3.6 nm. To assess the hydrothermal stability, samples were subjected to 100 °C distilled water for 300 h. The boiled mesoporous aluminosilicates have nearly the same N₂ adsorption-desorption isotherms and the same pore size distributions as those newly synthesized ones, indicating excellent hydrothermal stability. The ²⁹Si MAS NMR spectra confirmed that PMHS and TEOS have jointly condensed and CH₃ groups have been introduced into the materials. The ²⁷Al MAS NMR spectra indicated that Al atoms have been incorporated in the mesopore frameworks. The NH₃ temperature-programmed desorption showed strong acidity. Due to the existence of large amount of CH₃ groups, the mesoporous aluminosilicates obtained good hydrophobicity. Owing to the relatively large pore and the strong acidity provided by the uniform four-coordinated Al atoms, the excellent catalytic performance for 1,3,5-triisopropylbenzene cracking was acquired easily. The materials may be a profitable complement for the synthesis of solid acid catalysts.     

Ordered mesoporous silica-based inorganic nanocomposites

This article reviews the synthesis and characterization of nanoparticles and nanowires grown in ordered mesoporous silicas (OMS). Summarizing work performed over the last 4 years, this article highlights the material properties of the final nanocomposite in the context of the synthesis methodology employed. While certain metal-OMS systems (e.g. gold in MCM-41) have been extensively studied this article highlights that there is a rich set of chemistries that have yet to be explored. The article concludes with some thoughts on future developments and challenges in this area.     

Metallic mesoporous nanocomposites for electrocatalysis

We describe the fabrication, characterization, and applications of ultrathin, free-standing mesoporous metal membranes uniformly decorated with catalytically active nanoparticles. Platinum-plated nanoporous gold leaf (Pt-NPG) made by confining a plating reaction to occur within the pores of dealloyed silver/gold leaf is 100 nm thick and contains an extremely high, uniform dispersion of 3 nm diameter catalytic particles. This nanostructured composite holds promise as a prototypical member of a new class of fuel cell electrodes, showing good electrocatalytic performance at low platinum loading (less than 0.05 mg cm-2), while also maintaining long-term stability against coarsening and aggregation of catalytic nanoparticles.     

以微孔β沸石为硅铝源合成强酸性介孔分子筛

以微孔β沸石为硅铝源,通过碱处理和以十六烷基三甲基溴化铵为模板剂,合成了具有较强酸性的六方结构介孔分子筛材料B-MCM-41,并采用XRD、N₂吸附脱附、FT-IR、²7Al MAS NMR、HRTEM和水热处理等手段对其进行了结构表征,采用NH₃-TPD对其进行了酸性表征。实验结果表明,B-MCM-41具有明显强于常规介孔分子筛的酸性,且在C⁺₁0混合芳烃加氢脱烷基化反应中表现出了良好的催化性能。这主要是由于碱溶液将β沸石降解为沸石结构单元,在表面活性剂作用下五元环次级结构单元被引入了介孔铝硅酸盐B-MCM-41的结构。     

Hybrid nanocomposites based on guanidine methacrylate monomer and polymer and layered aluminosilicates: Synthesis, structure, and properties

Hybrid nanostructures (organomodified montmorillonite) have been synthesized on the basis of activated Na⁺-montmorillonite and new water-soluble ionogenic Na⁺-montmorillonite monomers containing quaternary ammonium guanidine cations. The structure and properties of poly(guanidine methacrylate) nanocomposites have been studied. It has been shown that these compounds efficiently adsorb heavy metals and exhibit a prolonged biocide effect due to the presence of quaternary ammonium guanidine cations.     

Responsive periodic mesoporous polydiacetylene/silica nanocomposites

Responsive PMO materials have been synthesized through co-assembly of bridged diacetylenic silsesquioxane and surfactant. The spatially defined polydiacetylenic component, mesoporous network, and the covalent proximity of polydiacetylene to silica endow the PMO with mechanical robustness, reversible chromatic responses, improved thermal stability, and faster responses to chemical stimuli. This research also provides an efficient molecular design and assembly paradigm to fabricate a family of conjugated optoelectronic materials, creating novel platforms for sensors, actuators, and other device applications.     

Synthesis of carboxylic acid esters in the presence of micro- and mesoporous aluminosilicates

The catalytic properties of zeolites HY, HBeta, and HZSM-12 and of mesoporous amorphous aluminosilicate in liquid-phase esterification of aliphatic (monobasic C₁–C₁₈, dibasic C₆, C₁₀) and aromatic (benzoic, trimellitic, phthalic) carboxylic acids with butanol were studied. Zeolite HBeta appeared to be the most active catalyst. Procedures were developed for preparing esters in the presence of zeolitic catalyst HBeta, ensuring 100% selectivity of ester formation at 90–98% conversion of the acid.     

Crystalline-like molecularly ordered mesoporous aluminosilicates derived from aluminosilica-surfactant mesophases via benign template removal

We report the preparation of mesoporous aluminosilicate materials that exhibit molecular-scale ordering in their pore wall framework. The materials were derived from mesoporous aluminosilica-surfactant mesophases via benign template removal methods, which allowed the retention of molecular ordering in surfactant-free materials. The molecularly ordered aluminosilica-surfactant mesophases were obtained from hydrothermal crystallization of cetyltrimethylammonium hydroxide/Al,Si/H2O systems at 135 degrees C for 12 days. Benign template removal via H2O2-mediated oxidation of the surfactant at room temperature was found to be the most effective method in generating surfactant-free materials with molecular ordering, high textural properties (depending on Al content), and high acidity. The Al in the resulting aluminosilicates was entirely incorporated in framework (tetrahedrally coordinated) sites. Template extraction in acidified ethanol also generated molecularly ordered materials but compromised the Al content and acidity. Template removal via conventional calcination generated porous materials with high textural properties but which exhibited only limited molecular ordering and had relatively low acidity and significant amounts of nonframework Al. This work demonstrates that molecular ordering in mesoporous silicate-surfactant mesophases is due to crystallographic ordering within inorganic frameworks rather than the arrangement/packing of surfactant molecules.     

Synthesis and applications of mesoporous nanocomposites containing metal nanoparticles

Metal nanoparticles (NP) and mesoporous (MP) oxides are complementary materials, since the size scale of pores in MP oxides matches that of NP and both systems have potential applications in similar fields. Besides, nanocomposites obtained through their combination possess not only the intrinsic properties of each component, but also new features derived from the synergy between them, mainly due to the high interfacial area between the metal and the oxide. Thus, new optical, catalytic and sensing properties can be achieved that are not easily available from the individual components. In this review, we focus our attention on such NP@MP composites, not only from the point of view of the most common synthesis pathways but also briefly describing their applications in fields as diverse as (photo)catalysis, sensing, photochromism and other optical properties, as well as patterning.     

Fabrication and characterization of mesoporous Co3O4 core/mesoporous silica shell nanocomposites

A mesoporous Co(3)O(4) core/mesoporous silica shell composite with a variable shell thickness of 10-35 nm was fabricated by depositing silica on Co(3)O(4) superlatticed particles. The Brunauer-Emmett-Teller (BET) surface area of the composite with a shell thickness of ca. 2.0 nm was 238.6 m(2)/g, which varied with the shell thickness, and the most frequent pore size of the shell was ca. 2.0 nm. After the shell was eroded with hydrofluoric acid, mesoporous Co(3)O(4) particles with a pore size of ca. 8.7 nm could be obtained, whose BET surface area was 86.4 m(2)/g. It is proposed that in the formation of the composite the electropositive cetyltrimethylammonium bromide (CTAB) micelles were first adsorbed on the electronegative Co(3)O(4) particle surface, which directed the formation of the mesoporous silica on the Co(3)O(4) particle surface. Electrochemical measurements showed that the core/shell composites exhibited a higher discharge capacity compared with that of the bare Co(3)O(4) particles.     

One-step direct synthesis of mesoporous aluminosilicates Al-SBA-15 with cage-like macropores by using micrometer-sized aluminum balls

Ordered mesoporous aluminosilicate Al-SBA-15 materials with cage-like macropores have been synthesized by using micrometer-sized aluminum balls as an Al source, tetraethyl orthosilicate (TEOS) as a silica source, and triblock copolymer Pluronic P123 as a template. The resulting materials were fully characterized by XRD, N₂ adsorption, SEM, TEM, ICP-AES, and ²⁷Al MAS-NMR. The products (Al-SBA-15) have ordered two-dimensional (2-D) hexagonal mesostructures (space group p6mm). The calcined Al-SBA-15 materials exhibit disordered macropores with diameters of about 70–80 nm and ordered mesopores with a diameter of ∼5 nm, a BET surface area of about 500 m²/g, Si/Al ratio of 40–80, and a ratio of tetrahedral Al to octahedral Al sites of about 2:1. This combination of properties gives these materials potential applications in areas such as adsorption, catalysis and separation. Supported by the National Natural Science Foundation of China (Grant Nos. 20890123 & 20721063), Shanghai Science & Technology Committee (08DZ2270500), and Shanghai Leading Academic Discipline Project (No.B108)