Effect of surface hydration on the photocatalytic activity of oxide catalysts in the CO oxidation

The effect of the state of hydrated surface of the bulk oxide photocatalysts, TiO₂, CeO₂, and ZnO on the rate of UV-induced oxidation of CO with atmospheric oxygen was studied. The activity of dehydroxylated catalyst samples evacuated at temperatures of >350 °C toward CO photooxidation decreases in the series CeO₂ > ZnO ≈ TiO₂, while that of partially hydrated samples after pretreatment at 20 °C changes in the order TiO₂ > ZnO ≥ CeO₂ ≈ 0. According to the results, the difference in the photocatalytic activity toward CO oxidation on the dehydrated ZnO, TiO₂, and CeO₂ catalysts is attributable to different concentrations of oxygen vacancies, which are formed more readily after high-temperature treatment on ZnO and CeO₂ and thus promote higher rate of CO photooxidation. Using a new technique for recording transmittance IR spectra, it was found that photoirradiation in the presence of adsorbed water and O₂ gives peroxides and hydroperoxides, with their concentrations decreasing in the series TiO₂ >> ZnO >> CeO₂. Most likely, these species are active intermediates of CO photooxidation with oxygen in the presence of adsorbed water. The hydrophobization effect was detected upon TiO₂ modification with zinc, resulting in removal of surface acid sites capable of adsorbing water. The TiO₂ modification with zinc increases the activity of CO photooxidation with respect to the oxidation catalyzed by samples pretreated at low temperatures (20—60 °C).     

Synthesis of W‐doped TiO2 by low‐temperature hydrolysis: Effects of annealing temperature and doping content on the surface microstructure and photocatalytic activity

A series of tungsten‐doped Titania photocatalysts were synthesized using a low‐temperature method. The effects of dopant concentration and annealing temperature on the phase transitions, crystallinity, electronic, optical, and photocatalytic properties of the resulting material were studied. The X‐ray patterns revealed that the doping delays the transition of anatase to rutile to a high temperature. A new phase W_yTi_1‐yO₂ appeared for 5.00 wt% W‐TiO₂ annealed at 900 °C. Raman and diffuse reflectance UV–Vis spectroscopy showed that band gap values decreased slightly up to 700 °C. X‐ray photoelectron spectroscopy showed that surface species viz. Ti³⁺, Ti⁴⁺, O^2?, oxygen‐vacancies, and adsorbed OH groups vary depending on the preparation conditions. The photocatalytic activity was evaluated via the degradation of methylene blue using LED white light. The degradation rate was affected by the percentage of dopants. The best photocatalytic activity was achieved with the sample labeled 5.00 wt% W‐TiO₂ annealed at 700 °C.     

An infrared study of adsorption of N2O on ZnO

The adsorption of N₂O on finely divided ZnO at room temperature shows two principal infrared absorption bands at 2237 cm⁻¹ (strong) and 1255 cm⁻¹ (weak), corresponding to the reversible adsorption of an N₂O surface species. The N₂O is postulated to be coordinated to Zn²⁺ cations by the oxygen atom. Water pre-treatment of the ZnO surface gives only weak bands from adsorbed N₂O, indicating that the latter's adsorption site is taken up by adsorbed water. Spectroscopic experiments on ‘reduced’ surfaces of ZnO at 200°C show that limited reaction of N₂O with the surface has occurred, presumably through decomposition to nitrogen and adsorbed oxygen. New adsorptions on the ZnO surface itself, and a reduced amount of reversibly adsorbed N₂O, implied a reduction in pressure of the adsorbate. Such effects were not observed appreciably over ‘oxidised’ ZnO.     

Photodegradation of 4-chlorophenol by UV/photocatalysts: the effect of the interparticle electron transfer process

Summary This study explores the photodegradation of 4-chlorophenol (4-CP). Coupled-photocatalyst systems are tested to determine whether the interparticle electron transfer (IPET) process improves the photodegradation efficiency. TiO₂, ZnO and SnO₂ are selected as photocatalysts. In the single-photocatalyst test, ZnO exhibits the highest catalytic activity. The pseudo first-order rate constant of the coupled-catalyst system, ZnO/SnO₂, is approximately 22% higher than that of ZnO; these rate constants are 0.95 and 0.78 h^-1 at pH 11, respectively.     

Characterization and activity of visible-light-driven TiO2 photocatalyst codoped with nitrogen and cerium

Nitrogen and cerium codoped TiO₂ photocatalysts were prepared by a modified sol-gel process with doping precursors of cerium nitrate and urea, and characterized by X-ray diffraction (XRD), thermogravimetry-differential scanning calorimetry (TG-DSC), X-ray photoelectron spectra (XPS) and ultraviolet-visible light diffuse reflectance spectra (UV-vis DRS). Results indicate that anatase TiO₂ is the dominant crystalline type in as-prepared samples, and CeO₂ crystallites appear as the doping ratio of Ce/Ti reaches to 3.0 at%. The TiO₂ starts to transform from amorphous phase to anatase at 987.1 K during calcination, according to the TG-DSC curves. The XPS show that three major metal ions of Ce³⁺, Ce⁴⁺, Ti⁴⁺ and one minor metal ion of Ti³⁺ coexist on the surface. The codoped TiO₂ exhibits significant absorption within the range of 400-500 nm compared to the non-doped and only nitrogen-doped TiO₂. The enhanced photocatalytic activity of the codoped TiO₂ is demonstrated through degradation of methyl orange under visible light irradiation.     

Doping level effect on visible-light irradiation W-doped TiO2–anatase photocatalysts for Congo red photodegradation

A series of W-modified TiO₂ (W–TiO₂) photocatalysts were synthesized by a simple sol–gel method. The new photocatalysts were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–vis-diffuse reflectance spectroscopy (DRS), and Brunauer, Emmett and Teller (BET) surface area analyzer. The photoactivity of the W–TiO₂ photocatalysts was evaluated by the photocatalytic oxidation of Congo red (CR) dye. It was found that the average size of the prepared photocatalysts is 10 nm. Moreover, they have high surface areas (∼ 216 m² g⁻¹) and their light-absorption extends to the visible region compared to pure TiO₂. The effects of W-loading and of the calcination temperature of the prepared photocatalysts on their photocatalytic activity were also studied. The obtained results show that the W_0.5–TiO₂ photocatalyst calcined at 350 °C is much highly photoactive than non-doped or highly doped TiO₂. The enhanced photocatalytic activity of the weakly doped TiO₂ may be attributed to the increase in the charge separation efficiency and the presence of surface acidity on the W_0.5–TiO₂ photocatalyst.     

Photocatalytic decomposition of orange II over TiO2-loaded on SBA-15 prepared using a microwave process

SBA-15 mesoporous material was prepared by microwave-hydrothermal method and was used as support in TiO₂-loaded SBA-15 photocatalysts. The physical properties of these particles were investigated. We also examined the activity of these samples as photocatalysts for the decomposition of orange II. Titania loaded on a silica matrix decreases the surface area of the support as expected for TiO₂ incorporation. For TiO₂-loaded SBA-15 photocatalysts, the IR absorption at ∼960 cm⁻¹ commonly accepted as the characteristic vibration of the Ti-O-Si bond. The photocatalytic activity increases with an increase of the TiO₂ loading.     

Hydrothermal ethanol conversion on Ag,Cu, Au/TiO2

The effect UV irradiation and silver, copper, and gold ions (M ^z+) supported on titania (anatase) have on the activity of M/TiO₂ samples in ethanol conversion at 150–400°C is examined. After UV irradiation, the yields of acetaldehyde and ethylene increase for TiO₂ and Ag/TiO₂ samples, while the activity of Cu²⁺/TiO₂ decreases. The activation energy of ethanol dehydration declines in the order TiO₂ > Au³⁺ > Cu²⁺ > Ag⁺ and correlates linearly with a reduction in the radius of M ^z+ in crystal. The number of acidic sites on a M/TiO₂ surface titrated via pyridine adsorption grows upon the introduction of M. Unlike Cu²⁺/TiO₂, these sites are not activated after the irradiation of TiO₂, Ag⁺/TiO₂, and Au³⁺/TiO₂. According to IR spectral data on adsorbed pyridine, all samples contain Lewis and Brönsted acidic sites.     

ZnO与骨架NiMo物理混合用于丙三醇催化重整-氢解制1,2-丙二醇

以骨架NiMo以及与氧化物物理混合, 考察了其在连续固定床反应器中无外加氢气条件下的丙三醇一锅法重整-氢解制1,2-丙二醇(1,2-PDO)的性能.研究发现, 骨架NiMo自身催化活性高, 但对1,2-PDO的选择性一般.当将其与MgO, SiO₂, Al₂O₃, HZSM-5, TiO₂, ZrO₂或CeO₂机械混合时, 丙三醇转化率和1,2-PDO选择性均发生下降.但当与ZnO物理混合时, 催化活性和选择性均有所提高, 1,2-PDO得率可达52.0%, 优于贵金属催化剂在该一锅法反应中得到的结果.物理混合的ZnO与骨架NiMo之间这种独特的协同作用, 归因于重整过程中产生的CO₂在ZnO上发生化学吸附, 原位增强了ZnO的路易斯酸性.这不仅促进了丙三醇在ZnO上脱水生成中间产物丙酮醇, 也促进了丙酮醇在骨架NiMo上加氢生成1,2-PDO.     

In situ infrared study of formate reactivity on water–gas shift and methanol synthesis catalysts

In order to investigate the methanol synthesis reaction from CO₂/H₂, a comparative study of the reactivity of formate species on different types of catalysts and catalyst supports has been carried out. Formic acid was adsorbed on water–gas shift catalysts, Cu/ZnO/Al₂O₃ methanol synthesis catalyst and ZnO/Al₂O₃ support, Cu/ZnO/ZrO₂ and Cu/ZnO/CeO₂ methanol synthesis catalysts as well as their corresponding supports ZnO/ZrO₂ and ZnO/CeO₂. Superior reactivity and selectivity of dedicated methanol synthesis catalysts was evidenced by their behavior during the subsequent heating ramp, when these samples showed the simultaneous presence of formates and methoxy species and a higher stability of these reaction intermediates in the usual temperature range for the methanol synthesis reaction.     

Preparation of disk‐like Pt/CeO2‐p‐TiO2 catalyst derived from MIL‐125(Ti) for excellent catalytic performance

A feasible strategy is reported for the synthesis of a disk‐like Pt/CeO₂‐p‐TiO₂ catalyst derived from the titanium‐based metal–organic framework (MOF) MIL‐125(Ti) through a few valid steps. To verify the successful synthesis and structural features of the Pt/CeO₂‐p‐TiO₂ catalyst, as‐prepared samples were characterized using several techniques. The characterizations demonstrated that MOF‐derived porous TiO₂ was appropriate for application as a support owing to its moderate surface area (101 m² g^?1) and suitable pore size (6 nm). Moreover, to study the effect of calcination temperature on the catalytic performance, the obtained catalyst was calcined at various temperatures. It was found that Pt/CeO₂‐p‐TiO₂ calcined at 550 °C exhibited the highest catalytic performance, evaluated by means of the reduction of 4‐nitrophenol monitored by UV–visible spectra. Furthermore, this catalyst showed good reusability with a conversion of 94% even after six cycles. Finally, a possible reaction mechanism was proposed to explain the reduction of 4‐nitrophenol to 4‐aminophenol over the Pt/CeO₂‐p‐TiO₂ catalyst.     

Efficiency of various semiconductor catalysts for photodegradation of Safranin-T

Semiconductor photocatalysis often leads to partial or complete mineralization of organic pollutants. In this study, photocatalytic degradation of Safranin-T, a hazardous textile dye, has been investigated using various semiconductors such as titanium dioxide (TiO₂), zinc oxide (ZnO), bismuth oxide (Bi₂O₃), cerium oxide (CeO₂), yttrium oxide (Y₂O₃), and zirconium oxide (ZrO₂). The experiments were carried out by irradiating the aqueous solution of Safranin-T containing photocatalysts with UV and air. Maximum decolorization of Safranin-T occurred with TiO₂ (99.8%), followed by ZnO (80.3%), Bi₂O₃ (57.1%), CeO₂ (13.1%), Y₂O₃ (12.2%), and ZrO₂ (10.2%). The rate of photocatalytic degradation varied with increasing concentration of Safranin-T. The equilibrium degradation data of Safranin-T by TiO₂ and ZnO were fitted to the Langmuir and Freundlich isotherm models. The Freundlich and Langmuir model showed satisfactory fit to the equilibrium degradation data for TiO₂ and ZnO, respectively. Photocatalytic degradation of Safranin-T followed pseudo second-order kinetics.     

Preparation and characterization of mesoporous TiO2-CeO2 nanopowders respond to visible wavelength

Mesoporous TiO₂-CeO₂ nanopowders responding to visible wavelength were synthesized by using a surfactant assisted sol-gel technique. They were obtained using metal alkoxide precursors modified with acetylacetone (ACA) and laurylamine hydrochloride (LAHC) as surfactant. The samples were characterized by XRD, nitrogen adsorption isotherm, SEM, TEM, and selected area electron diffraction (SAED), respectively. The 95 mol% TiO₂-5 mol% CeO₂ system yielded single anatase phase, however, further addition of the CeO₂ formed cubic CeO₂ structure while anatase TiO₂ decreased. Additions of 5 and 10 mol% CeO₂ increased the surface area, but those of 25, 50, and 75 mol% CeO₂ did not affect it very much. By using this mixed metal oxides system, TiO₂ can be modified to respond to the visible wavelength. The mixed metal oxides had catalytic activity (evaluating the formation rate of I₃⁻) about 2-3 times higher than pure CeO₂, while nanosize anatase type TiO₂ materials had no catalytic activity under visible light. The catalytic activity was almost proportional to the specific surface area. The formation rate of I₃⁻ was much improved by changing the calcination temperature and calcination period. Highest catalytic activity in this study was obtained for the 50 mol% TiO₂-50 mol% CeO₂ nanopowders calcined at 250 °C for 24 h.     

IR-analysis of H-bonded H2O on the pure TiO2 surface

The surface state of optically pure polydisperse TiO₂ (anatase and rutile) was determined by infra-red (IR) spectroscopy analysis in the temperature range of 100–453 K. Anatase A300 spectrum, contrary to rutile R300 one, has a broad three-component absorption band with peaks at 1048, 1137 and 1222 cm⁻¹ in the spectral range of δ(Ti–O–H) deformation vibrations. For rutile R300 we observed a very weak band at 1047 cm⁻¹, and for the thermal treated rutile R900 these bands were not appeared at all. The analysis of temperature dependencies for the mentioned absorption bands revealed the spectral shift of 1222 cm⁻¹ band towards the high frequencies, when the temperature increased, but the spectral parameters of 1137 and 1048 cm⁻¹ bands remained the same. The temperature of 1222 cm⁻¹ band maximum shift was 373–393 K and correlated with DSC data. Obtained results allowed to assign 1222 cm⁻¹ band to the deformation vibrations of OH-groups, bounded to the surface adsorbed water molecules by weak hydrogen bonds (5 kcal/mol). During the temperature growth these molecules desorbed, which also resulted in the intensity decreasing of stretching OH-groups vibration IR-bands at 3420 cm⁻¹. The destruction and desorption of surface water complexes led to Ti–O–H bond strengthening. IR bands at 1137 and 1048 cm⁻¹ were attributed to the stronger bounded adsorbed water molecules, which are also characterized with stretching OH-groups vibration bands at 3200 cm⁻¹. These surface structure were additionally stabilized by hydrogen bonds with the neighbouring TiO₂ lattice anions and other OH-groups, and desorbed at higher temperatures.     

Adsorption properties and photocatalytic activity of TiO2 and La-doped TiO2

Photocatalysts of TiO₂ and La-doped TiO₂ were prepared by calcining the pure TiO₂ sols and the sols mixed with La(NO₃)₃⋅6H₂O at 873 K, respectively. These photocatalysts were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and N₂ adsorption-desorption isotherms measurement. As results, the BET surface area, pore diameter, mesopore volume and micropore volume slightly increased, while the crystallite size and the phase structure were little affected by lanthanum doping. The equilibrium adsorption of methylene blue (MB) on the photocatalysts were measured in a dark room. The adsorption isotherms were confirmed to fit to the Langmuir theory. Photocatalytic activities of the photocatalysts were studied by employing the photocatalytic degradation of MB in water and degradation of acetaldehyde in air under UV-irradiation using a black light. Kinetic analysis revealed that the rate controlling steps could be the surface reaction of the adsorbed MB on the catalyst surface for MB degradation and the reaction of adsorbed acetaldehyde with the gaseous acetaldehyde for degradation of acetaldehyde, respectively.     

Tuning the Surface Structure of Nitrogen‐Doped TiO2 Nanofibres—An Effective Method to Enhance Photocatalytic Activities of Visible‐Light‐Driven Green Synthesis and Degradation

Nitrogen‐doped TiO₂ nanofibres of anatase and TiO₂(B) phases were synthesised by a reaction between titanate nanofibres of a layered structure and gaseous NH₃ at 400–700 °C, following a different mechanism than that for the direct nitrogen doping from TiO₂. The surface of the N‐doped TiO₂ nanofibres can be tuned by facial calcination in air to remove the surface‐bonded N species, whereas the core remains N doped. N‐Doped TiO₂ nanofibres, only after calcination in air, became effective photocatalysts for the decomposition of sulforhodamine B under visible‐light irradiation. The surface‐oxidised surface layer was proven to be very effective for organic molecule adsorption, and the activation of oxygen molecules, whereas the remaining N‐doped interior of the fibres strongly absorbed visible light, resulting in the generation of electrons and holes. The N‐doped nanofibres were also used as supports of gold nanoparticle (Au NP) photocatalysts for visible‐light‐driven hydroamination of phenylacetylene with aniline. Phenylacetylene was activated on the N‐doped surface of the nanofibres and aniline on the Au NPs. The Au NPs adsorbed on N‐doped TiO₂(B) nanofibres exhibited much better conversion (80 % of phenylacetylene) than when adsorbed on undoped fibres (46 %) at 40 °C and 95 % of the product is the desired imine. The surface N species can prevent the adsorption of O₂ that is unfavourable for the hydroamination reaction, and thus, improve the photocatalytic activity. Removal of the surface N species resulted in a sharp decrease of the photocatalytic activity. These photocatalysts are feasible for practical applications, because they can be easily dispersed into solution and separated from a liquid by filtration, sedimentation or centrifugation due to their fibril morphology.     

Effect of the microstructure of the supported catalysts CuO/TiO<Subscript>2</Subscript> and CuO/(CeO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript>) on their catalytic properties in carbon monoxide oxidation

The effect of the microstructure of titanium dioxide on the structure, thermal stability, and catalytic properties of supported CuO/TiO₂ and CuO/(CeO₂-TiO₂) catalysts in CO oxidation was studied. The formation of a nanocrystalline structure was found in the CuO/TiO₂ catalysts calcined at 500°C. This nanocrystalline structure consisted of aggregated fine anatase particles about 10 nm in size and interblock boundaries between them, in which Cu²⁺ ions were stabilized. Heat treatment of this catalyst at 700°C led to a change in its microstructure with the formation of fine CuO particles 2.5–3 nm in size, which were strongly bound to the surface of TiO₂ (anatase) with a regular well-ordered crystal structure. In the CuO/(CeO₂-TiO₂) catalysts, the nanocrystalline structure of anatase was thermally more stable than in the CuO/TiO₂ catalyst, and it persisted up to 700°C. The study of the catalytic properties of the resulting catalysts showed that the CuO/(CeO₂-TiO₂) catalysts with the nanocrystalline structure of anatase were characterized by the high-est activity in CO oxidation to CO₂.     

CNTs表面改性与TiO2-CNTs异质结光催化性能

碳纳米管(CNTs)混酸(H₂SO₄/HNO₃, 体积比为3:1)超声辅助纯化及氧化植入活性基团－COOH, 进一步借助其转化为酰氯基团, 分别于CNTs 表面共价嫁接亲水性赖氨酸及亲脂性正十八胺基团, 赋予赖氨酸表面改性CNTs 显著水溶(6.85 mg·mL-1)和十八胺表面改性CNTs 显著醇溶(10.15 mg·mL^-1)性能. 运用低温水热法以亲水性CNTs 复合TiO₂, 溶胶-凝胶法以亲脂性CNTs 复合TiO₂, 观察到复合催化剂光催化性能随CNTs 溶剂分散性能增加而明显提升. 运用傅里叶变换红外(FTIR)、激光拉曼、X射线衍射(XRD)、Brunauer-Emmett-Teller 低温氮气吸附、透射电镜(TEM)及X光电子能谱(XPS)等手段表征, 系统探讨CNTs 的表面改性机制及CNTs 溶解分散性能与复合催化剂的光活性的关联. 认为表面改性CNTs 借助Ti－O－C键合促进其与纳米TiO₂的异质结合, 从而充分利用CNTs的大比表面积及电荷传输性能促进催化剂的污染物光催化降解.     

Photodegradation of Rhodamine B on Sulfur Doped ZnO/TiO2 Nanocomposite Photocatalyst under Visible-light Irradiation

Sulfur doped ZnO/TiO₂ nanocomposite photocatalysts were synthesized by a facile sol‐gel method. The structure and properties of catalysts were characterized by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), UV‐vis diffusive reflectance spectroscopy (DRS) and N₂ desorption‐adsorption isotherm. The XRD study showed that TiO₂ was anatase phase and there was no obvious difference in crystal composition of various S‐ZnO/TiO₂. The XPS study showed that the Zn element exists as ZnO and S atoms form SO^2?₄. The prepared samples had mesoporosity revealed by N₂ desorption‐adsorption isotherm result. The degradation of Rhodamine B dye under visible light irradiation was chosen as probe reaction to evaluate the photocatalytic activity of the ZnO/TiO₂ nanocomposite. The commercial TiO₂ photocatalyst (Degussa P25) was taken as standard photocatalyst to contrast the prepared different photocatalyst in current work. The improvement of the photocatalytic activity of S‐ZnO/TiO₂ composite photocatalyst can be attributed to the suitable energetic positions between ZnO and TiO₂, the acidity site caused by sulfur doping and the enlargement of the specific area. S‐3.0ZnO/TiO₂ exhibited the highest photocatalytic activity under visible light irradiation after Zn amount was optimized, which was 2.6 times higher than P25.     

Nanosized CeO2–SiO2, CeO2–TiO2, and CeO2–ZrO2 Mixed Oxides: Influence of Supporting Oxide on Thermal Stability and Oxygen Storage Properties of Ceria

The influence of SiO₂, TiO₂, and ZrO₂ on the structural and redox properties of CeO₂ were systematically investigated by various techniques namely, X-ray diffraction (XRD), Raman spectroscopy (RS), UV–Vis diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), high-resolution transmission electron microscopy (HREM), BET surface area, and thermogravimetry methods. The effect of supporting oxides on the crystal modification of ceria was also mainly focused. The investigated oxides were obtained by soft chemical routes with ultrahigh dilute solutions and were subjected to thermal treatments from 773 to 1073 K. The XRD results suggest that the CeO₂–SiO₂ sample primarily consists of nanocrystalline CeO₂ on the amorphous SiO₂ surface. Both crystalline CeO₂ and TiO₂-anatase phases were noted in the case of CeO₂–TiO₂ sample. Formation of cubic Ce_0.75Zr_0.25O₂ and Ce_0.6Zr_0.4O₂ (at 1073 K) were observed in the case of CeO₂–ZrO₂ sample. The cell ‘a’ parameter estimations revealed an expansion of the ceria lattice in the case of CeO₂–TiO₂, while a contraction is noted in the case of CeO₂–ZrO₂. The DRS studies suggest that the supporting oxides significantly influence the band gap energy of CeO₂. Raman measurements disclose the presence of oxygen vacancies, lattice defects, and displacement of oxide ions from their normal lattice positions in the case of CeO₂–TiO₂ and CeO₂–ZrO₂ samples. The XPS studies revealed the presence of silica, titania, and zirconia in their highest oxidation states, Si(IV), Ti(IV), and Zr(IV) at the surface of the materials. Cerium is present in both Ce⁴⁺ and Ce³⁺ oxidation states. The HREM results reveal well-dispersed CeO₂ nanocrystals over the amorphous SiO₂ matrix in the case of CeO₂–SiO₂, isolated CeO₂ and TiO₂ (A) nanocrystals and some overlapping regions in the case of CeO₂–TiO₂, and nanosized CeO₂ and Ce–Zr oxides in the case of CeO₂–ZrO₂ sample. The exact structural features of these crystals as determined by digital diffraction analysis of HREM experimental images reveal that the CeO₂ is mainly in cubic fluorite geometry. The oxygen storage capacity (OSC) as determined by thermogravimetry reveals that the OSC of mixed oxides is more than that of pure CeO₂ and the CeO₂–ZrO₂ exhibits highest OSC.