Kinetic determination of ultramicro amounts of copper

A new catalytic reaction is proposed and a kinetic method developed for the determination of ultramicro amounts of Cu(II) on the basis of its catalytic activity in oxidation of the 2-thiosemicarbazone of sodium 1,2-naphthoquinone-4-sulphonate by hydrogen peroxide in the presence of ascorbic acid. Under optimal conditions the sensitivity of the method is 0.25 ng/ml. The relative error is 4.8-18.2% for the concentration range 5-0.8 ng/ml. Most foreign ions do not change the rate of the catalysed reaction. Co(2+) and I(-) catalyse the reaction, Ni(2+) extensively inhibits it, and in the presence of EDTA only the uncatalysed reaction takes place.     

New spectrophotometric method for the determination of trace amounts of palladium

Summary A simple, rapid, selective, and sensitive method for the spectrophotometric determination of palladium is developed based on the reaction of Pd(II) with 1-amino-4-hydroxyanthraquinone (AMHA). The reaction is carried out atpH 3.8 in 50% (v/v) ethanol-water medium. The molar absorptivity of the complexed ligand is 1.1 · 10⁴ l mol^–1 cm^–1 at 620 nm. Calibration plots are linear up to 17 µg Pd cm^–3. The optimum concentration range (Ringbom plot) is between 3–14.5 µg cm^–3. The spectral study of the reaction in solutions containing equimolar concentrations or an excess of one component, in thepH range 0.3–6.5, indicate the possible complex transitions that occur in solution. Complete graphical and logarithmic analysis of the absorbance-pH graphs was performed to demonstrate and characterize the complexation equilibria in solution. Under the optimum conditions, palladium can be determined as the noncharged complex Pd(AMHA)₂ in the presence of a large number of foreign ions. Interferences caused by zirconium(IV) could be masked with fluoride ions.

---

Eine neue spektrophotometrische Methode für die Bestimmung von Palladium in Spuren

Zusammenfassung Eine einfache, schnelle und empfindliche Methode für die spektrophotometrische Bestimmung von Palladium wurde auf der Basis der Reaktion von Pd(II) mit 1-Amino-4-hydroxyanthrachinon (AMHA) entwickelt. Die Reaktion wird in 50% (v/v) Ethanol/Wasser beipH 3.8 ausgeführt. Die molare Absorption des komplexierten Liganden beträgt 1.1 · 10⁴ l mol^–1 cm^–1 bei 620 nm. Kalibrierungskurven verlaufen bis zu 17 µg Pd cm^–3 linear. Der optimale Konzentrationsbereich (Ringbom-Plot) liegt zwischen 3 und 14.5 µg cm^–3. Spektroskopische Untersuchungen der Reaktion in Lösungen, entweder mit equimolaren Konzentrationen oder mit einem Überschuß an einer Komponente impH-Bereich 0.3–6.5, lassen Rückschlüsse auf mögliche Komplex-Übergänge in Lösung zu. Es wurde eine vollständige graphische, logarithmische Analyse der Absorptions-pH-Graphen durchgeführt, um die Komplexgleichgewichte in Lösung aufzuklären und zu charakterisieren. Unter den Optimalbedingungen kann Palladium als nichtgeladener Komplex Pd(AMHA)₂ in Gegenwart einer großen Anzahl an Fremd-Ionen bestimmt werden. Schwierigkeiten mit Zirkonium(IV) konnte durch Maskierung mit Fluorid-Ionen umgangen werden.

     

Spectrophotometric and analogue derivative spectrophotometric determination of ultramicro amounts of cadmium with cationic porphyrins

alpha,beta,gamma,delta-Tetrakis(1-methylpyridinium-3-yl)porphine [T(3-MPy)P] and alpha,beta,gamma,delta-tetrakis(1-methylpyridinium-4-yl)porphine [T(4-MPy)P] have been found to react rapidly with cadmium to give coloured complexes in weakly alkaline media at room temperature. Simple and practical methods for the determination of cadmium at ng/ml levels by conventional and analogue derivative spectrophotometry have been proposed. The analogue method gives higher sensitivity. T(3-MPy)P gives higher sensitivity than T(4-MPy)P. The interference of various foreign cations and anions has also been examined and in many cases eliminated or reduced. Adsorption of the porphyrins and their cadmium complexes onto the glassware, which is usually observed under the conditions of reaction and causes significant errors in the determination, can be suppressed almost completely by addition of fairly large amounts of a salt such as sodium chloride.     

Flow injection kinetic spectrophotometric method for the determination of trace amounts of nitrite

In this work, a new, simple and sensitive flow injection catalytic kinetic spectrophotometric determination of nitrite is reported based on catalytic effect of nitrite on the redox reaction between sulfonazo III and potassium bromate in acidic media. The reaction was monitored by measuring the decrease in the absorbance of sulfunazo III at 570 nm. Various chemical (such as the effect of acidity, reagents concentrations) and instrumental parameters (flow rate, reaction coil length, injection volume and temperature) were studied and were optimized. Under the optimum conditions calibration graph was linear in the nitrite concentration ranges of 8.00 × 10⁻³-3.00 × 10⁻¹ μg/ml (with slope of 2.40) and 3.50 × 10⁻¹-1.80 μg/ml (with slope of 0.42). The detection limit was 6.00 × 10⁻³ μg/ml of nitrite, the relative standard deviation (n = 10) was 1.25% and 0.88% for 5.00 × 10⁻² and 2.00 × 10⁻¹ μg/ml of nitrite respectively. About 60 samples in 1 h can be analyzed. The interfering effects of various chemical species were studied. The method was successfully applied in the determination of nitrite in food and environmental samples.     

New spectrophotometric method for determination of cephazolin

A simple, selective and accurate spectrophotometric method has been developed for the determination of the cephalosporin-type antibiotic cephazolin. The method is based on the fast preliminary acid hydrolysis of cephazolin and the spectrophotometric determination of one of its degradation products-2-mercapto-5-methylthiadiazole.     

A chemical enhancement method for the spectrophotometric determination of trace amounts of arsenic

A highly sensitive spectrophotometric method for the determination of 0.03-1.0 microg of arsenic is described. After extraction as AsI(3) into benzene, it is selectively stripped into water. Both the arsenic(III) and iodide present in the aqueous phase are made to react with iodate in acidic medium in the presence of chloride to form the anionic chloro complex, ICl(-)(2). The determination is completed after extraction of ICl(-)(2) species as an ion-pair with Rhodamine 6G into benzene and measuring the absorption of the extract at 535 nm. The coefficient of variation is 1.5% for 10 determinations of 0.5 microg of arsenic. The method has been applied to the determination of arsenic content in plant materials, high purity iron, copper base alloys and inorganic arsenic levels of natural waters.     

Atomic-absorption spectrophotometric determination of ultramicro amounts of selenium(IV) and total selenium in sulphuric acid

Summary Ultramicro amounts of selenium in sulphuric acid are determined by a new atomic absorption spectrophotometric method. Selenium(IV) is directly determined ater extraction into toluene with an aromatic o-diamine and addition of nickel(II) prior to atomization; the determination of total selenium (0, IV and VI) needs a treatment of the sample with selected oxidizing and reducing agents.In the studied samples, total selenium (0.003–0.022 g of Se in 1 ml sulphuric acid) is present only in the tetravalent state. The detection limit of the method is 0.003 g of selenium.

---

Atomabsorptions-spektralphotometrische Bestimmung von Ultramikromengen Selen(IV) und Gesamtselen in Schwefelsäure

Zusammenfassung Selen(IV) kann direkt bestimmt werden nach Toluolextraktion der mit einem aromatischen o-Diamin behandelten Lösung und Zusatz von Nickel(II). Die Bestimmung von Gesamtselen (0, IV, VI) erfordert eine Vorbehandlung mit Perchlor- bzw. Salpetersäure und Wasserstoffperoxid. Die Nachweisgrenze des Verfahrens beträgt 0,003 g Se. In den untersuchten Proben war das Gesamtselen (0,003–0,022 g/ml) nur als Se(IV) vorhanden.

     

A highly sensitive spectrophotometric method for determination of micro amounts of arsenic

A highly sensitive spectrophotometric method for determination of arsenic, based on the formation of an ion-association complex between arsenoantimonomolybdenum blue and Malachite Green, has been developed. The ion-association complex is soluble in the presence of Triton X-305, so arsenic can be determined directly in aqueous solution. The apparent molar absorptivity for arsenic is 1.13 x 10(5) l.mole(-1).cm(-1) at 640 nm. Beer's law is obeyed for 0-5 mug of arsenic. The lower limit of determination (absorbance = 0.01) is 4 ng ml in the final solution.     

A selective spectrophotometric method for determination of copper with ferron

A selective spectrophotometric determination of copper is based on extraction of the copper-ferron complex with tribenzylamine in chloroform at low acidity, and measurement of the absorbance of the yellow extract at 410 nm. Beer's law is found to hold up to 8 microg/ml copper concentration. Of 30 elements tested, only molybdenum interferes. The ratio copper:ferron:tribenzylamine in the extracted species is 1:2:2.     

New spectrophotometric method for the determination of phenolic hormones

A new simple, selective and accurate spectrophotometric method is described for the determination of mono- and dihydric phenolic hormones (oestrogens and catecholamines) by nitration at 50 degrees and 100 degrees , respectively, for 10 min, followed by treatment with alkali. Coloured products with absorption maxima at 430, 385, 430, 380 and 380 nm, linearly proportional to the concentration of oestrone, oestradiol, ethinyloestradiol, adrenaline and noradrenaline, respectively, are obtained. Information is presented on the effect of nitration time, temperature, solvents, and alkali concentration. The method is satisfactorily applied to the determination of these hormones in the range 10-50mug ml in the final solution, of volume 10ml. The relative standard deviation is +/- 0.5% and no interferences are caused by non-phenolic hormones.     

Sequential injection lab-on-valve simultaneous spectrophotometric determination of trace amounts of copper and iron

A sequential injection (SI) method in a lab-on-valve (LOV) format for simultaneous spectrophotometric determination of copper and iron has been devised. The detection chemistry is based on the complex formation of 2-(5-bromo-2-pyridylazo)-5-[N-n-propyl-N-(3-sulfopropyl)amino]aniline (5-Br-PSAA) with copper(II) and/or iron(II) at pH 4.6. Copper(II) reacts with 5-Br-PSAA to form the complex which has an absorption maximum at 580 nm but iron(III) does not react. In the presence of a reducing agent only iron(II)-5-Br-PSAA complex is formed and detected at 558 nm. Under the optimum experimental conditions, the determinable ranges are 0.1-2 mg l⁻¹ for copper and 0.1-5 mg l⁻¹ for iron, respectively, with a sampling rate of 18 h⁻¹. The limits of detection are 50 μg l⁻¹ for copper and 25 μg l⁻¹ for iron. The relative standard deviations (n = 15) are 2% for 0.5 mg l⁻¹ copper and 1.8% for 0.5 mg l⁻¹ iron when determined in standard solutions. The recoveries range between 96 and 105% when determining 0.25-2 mg l⁻¹ of copper and 0.2-5 mg l⁻¹ of iron in artificial mixtures at copper/iron ratios of 1:10 to 5:1. The proposed SI-LOV method is successfully applied to the simultaneous determination of copper and iron in multi-element standard solution and in industrial wastewater samples.     

Solid-phase extraction and spectrophotometric determination of trace amounts of copper in water samples

A simple method for rapid and selective extraction, preconcentration and determination of copper as it's neocuproine complex by using octadecylsilica membrane disks and spectrophotometry is presented. Extraction efficiency and the influence of flow rates of sample solution and eluent, pH, amount of neocuproine and hydroxylamine hydrochloride, type and least amount of eluent for elution of copper complex from disks, break through volume and limit of detection were evaluated. Also the effects of various cationic interferences on percent recovery of copper were studied. Extraction efficiencies >99% were obtained by elution of the disks with minimal amount of solvent. The limit of detection of the proposed method is 0.12 ppb. The method was applied to the recovery and determination of copper in different water samples.     

A New catalytic reaction for determination of nanogram amounts of copper

Summary A simple and very sensitive new catalytic method is proposed for determination of copper(II). The method is based on the oxidation of sulphanilic acid with H₂O₂ at pH 7 in the presence of pyridine as activator. The sensitivity of the method is 5 ng/ml. Cobalt(II) interferes at concentrations of the same order as copper(II). The method is suitable for determination of copper in biological materials.

---

Zusammenfassung Eine einfache und sehr empfindliche katalytische Methode zur Bestimmung von Kupfer(II) wurde vorgeschlagen. Sie beruht auf der Oxydation von Sulfanilsäure mit Wasserstoffperoxid bei pH 7 in Gegenwart von Pyridin als Aktivator. Ihre Empfindlichkeit beträgt 5 ng/ml. Kobalt(II) stört in Konzentrationen der gleichen Größenordnung wie Kupfer(II). Das Verfahren eignet sich zur Kupferbestimmung in biologischem Material.

     

Kinetic determination of ultramicro amounts of Sn(II)

Summary A kinetic method is suggested for determining traces of Sn(II), on the basis of their inhibiting effect on the Fe(III) catalysis of oxidation of 4-amino-N, N-diethylaniline sulphate by hydrogen peroxide. The sensitivity of the method is 10 ng/ml. The error is below 11% and the method has relatively good selectivity.

---

Kinetische Bestimmung von Ultramikromengen Sn(II)

Zusammenfassung Auf der Grundlage des Hinderungseffektes auf die durch Fe(III) katalysierte Oxydation von 4-Amino-N, N-diethylanilinsulfat durch Wasserstoffperoxid wurde eine kinetische Methode zur Bestimmung von Sn(II)-Spuren vorgeschlagen. Deren Empfindlichkeit beträgt 10 ng/ml. Der Fehler liegt unter 11%, ihre Selektivität ist verhältnismäßig gut.

     

An accurate spectrophotometric method for determination of small amounts of water in acidic methanol

The method is based on u.v. measurement of the keto—ketal equilibrium of substituted acetophenones; 4-methoxyacetophenone proved most satisfactory, the standard deviation for 67 ppm of water in hydrobromic acid-containing methanol being 3 ppm.     

New method for detection and spectrophotometric determination of quinones

The reaction between 3-phenylthiazolidine-2,4-dione (I) and p-benzoquinone (II), tetrachloro-p-benzoquinone (III), and 1,4-naphthoquinone (IV) in ammoniacal medium is applied for detection and spectrophotometric determination of quinones. The absorbance-concentration relationship is linear up to 18 μg/ml of quinone concentration. The lower limits of identification in the detection reaction are 2.5, 3.0, and 1 μg for (II), (III), and (IV), respectively, which reflect high sensitivity. The reaction between (I) and quinones is proved to be a condensation reaction and highly selective.     

Sensitive spectrophotometric method for trace amounts of uranium

A sensitive spectrophotometric method for the determination of uranium with Pyrogallol Red (PGR) and cetyltrimethylammonium bromide (CTAB) is described. The sensitivity of the colour reaction between uranium and Pyrogallol Red is greatly increased in the presence of cetyltrimethylammonium bromide. The blue ternary complex (λ_max580 nm) has composition 1:2:4 [U(VI):PGR:CTAB] at pH 5.6. Beer's law is obeyed over the range 19.0-0.24 ppm of uranium and the molar absorptivity is 3.3 × 10⁴ l.mole⁻¹.cm⁻¹ at 620 nm. A tentative structure for the ternary complex is suggested. A simple method is suggested for evaluation of stability constants of such ternary complexes.     

An ultraviolet spectrophotometric method for the determination of small amounts of vanadium in ores and steel

The method proposed is suitable for a quick routine determination of small amounts of vanadium in certain ores and steel. The interference of chromium in the final determination of vanadium using the ultraviolet spectra was eliminated by the use of an ion-exchange resin. Reproduceability of results was found to be acceptable for a colorimetric method.     

Gas-chromatographic determination of ultramicro amounts of selenium in pure sulphuric acid

Ultramicro amounts of selenium in pure sulphuric acid are converted into selenous acid with a bromine-bromide redox buffer solution. The selenous acid reacts quantitatively with 4-nitro-o-phenyl-enediamine to form 5-nitropiaselenol which can be extracted into toluene. The extract is very sensitive to electron-capture detection in gas chromatography, and the sensitivity is higher than that of 5-chloro-or 4, 5-dichloro-piaselenol. The calibration curve (peak heights) is linear up to 0.15 mug of selenium in 1 ml of toluene. Pure sulphuric acid, commercially available, contains 10(-6)$ 10(-5) % selenium.     

Kinetic spectrophotometric method for the determination of trace amounts of oxalate by an activation effect.

A new, simple and inexpensive kinetic catalytic spectrophotometric method for the determination of oxalate is described. The method is based on an activation effect of oxalate on a catalytic effect of iron(II) on the oxidation of iodide by bromate. The reaction is monitored by measuring the absorbance of triiodide ion at lambda max = 352 nm. A calibration graph was obtained from 0.10 - 7.0 microg cm(-3) of oxalate with a detection limit of 0.080 microg cm(-3). The standard deviations for ten replicate determinations of 0.50, 1.0 and 5.0 microg cm(-3) of oxalate were 4.0, 2.6 and 1.8%, respectively. The applicability of the method was demonstrated by the determination of oxalate ion in real samples.