多酸/邻菲罗啉钌LBL薄膜的制备及电化学调控荧光开关性能

通过层层静电自组装技术制备了基于电致变色多酸P_8W_(48)与发光邻菲罗啉钌Ru(phen)的杂化红光薄膜[(PEI/P_8W_(48))_m/PEI/PSS/Ru(phen)/PSS]_(15)[m=1,3,5;PEI=聚乙烯亚胺;PSS=聚(4-苯乙烯磺酸钠)].利用紫外-可见光谱对薄膜的组成及增长进行了表征;通过循环伏安法对薄膜的电化学氧化还原性质进行了考察;通过荧光光谱对薄膜的发光性质进行了研究.结果表明,薄膜在外加氧化还原电位下呈现出可逆的电致变色-荧光开关性质;在阶跃电位-0.85 V/0.85 V下循环50次,其电致变色及荧光开关性能没有明显的减弱,体现了良好的电化学稳定性.     

多金属氧酸盐电致变色材料

多金属氧酸盐具有多样的结构和良好的电化学可逆性,在电致变色器件(例如军事伪装、后视镜、智能窗以及高对比度信息显示器)上有着广阔的应用前景。本文综述了多金属氧酸盐在电致变色领域的研究进展情况。概述了多金属氧酸盐的电致变色机理以及制备多金属氧酸盐电致变色薄膜的方法,主要包括:溶胶-凝胶方法、电沉积法、Langmuir-Blodgett方法、层接层自组装方法。按照多金属氧酸盐的结构类型分类,结合最新文献报道,介绍了同多酸(盐)型和杂多酸(盐)型电致变色材料性能的研究现状。最后,对其未来的发展方向进行了展望。     

钒修饰磷钨酸盐/刚果红电致变色膜的制备及性能研究

借助Layer-by-Layer自组装技术分别构筑了钒修饰的钨酸盐K_7P_2W_(17)VO_(62)·18H_2O(P_2W_(17)V)、聚乙烯亚胺的复合膜[PEI/P_2W_(17)V]_(20),K_7P_2W_(17)VO_(62)·18H_2O(P_2W_(17)V)、聚乙烯亚胺、刚果红(Congo red,CR)复合膜[PEI/P_2W_(17)V/PEI/刚果红]_(20)。紫外-可见吸收光谱监测显示两种复合膜的构筑是成功的,均实现了复合膜均一稳定的增长。电化学工作站和紫外可见吸收光谱联机对复合膜的电致变色性能研究显示:染料刚果红的加入,不但丰富了多酸电致变色材料的颜色种类,实现了由红色到浅紫色的可逆变化,更使光反差提高9.36%,复合膜的变色能力得到了很大的增强,实现了复合膜可调颜色的电致变色,有望在变色薄膜领域得到新的应用。     

多酸-中性红复合膜的制备及可调变的电致变色性能

利用层接层自组装方法,将Keggin型多酸(PW_(12))和染料中性红(NR)制备成复合膜材料.采用紫外-可见吸收光谱(UV-vis)、扫描电子显微镜(SEM)和循环伏安法(CV)等手段对复合材料的形貌和电致变色性能进行了表征.复合膜材料呈现出良好的电致变色性能,其光反差可达6.0%,着色效率高达14.6cm~2/C,着色与褪色时间分别为14.6和16.9s.而且,复合膜实现了深粉色、淡紫色和深紫色的可调变颜色变化.     

氧化石墨烯/聚电解质层层自组装制备单价离子选择性膜

采用层层自组装法在改性聚丙烯腈(PAN)膜表面交替沉积聚乙烯亚胺(PEI)和聚丙烯酸-氧化石墨烯(PAA-GO)混合液,制得了单价离子选择性复合膜。X射线衍射(XRD)测试结果表明成功合成了氧化石墨烯(GO)并在复合膜中均匀分散。扫描电镜(SEM)观察结果证实了多层聚电解质PEI/PAA-GO成功地组装在基膜上,并用紫外-可见(UV-Vis)光谱进一步证实了组装过程的均匀性和连续性。接触角和性能测试表明加入GO后,复合膜的亲水性和单价阳离子的选择性明显增大。这种高通量、高选择性的防污复合膜在分离和水的软化方面有很好的应用前景。     

钒钨酸盐-CdS纳米粒子复合膜的制备与电致变色性能

通过层-层自组装方法制备了由Dawson结构三钒取代型钨酸盐1-K₉P₂W₁₅V₃O₆₂·18H₂O(P₂W₁₅V₃)与CdS纳米粒子构筑的复合膜材料, 研究了CdS纳米粒子添加和复合膜层数对P₂W₁₅V₃多酸复合膜材料电致变色性能的影响. 采用UV, XRD, SEM和循环伏安等测试手段对复合材料的结构和性能进行了表征; 将电化学工作站和紫外-可见吸收光谱联用, 在-1.0~+1.0 V的电压范围内, 对不同层数、 有无CdS纳米粒子复合的的膜材料的电致变色性能进行研究. 研究结果表明, 20层的复合膜材料性能最佳, 光反差为38.05%, 着色时间为3.57 s, 褪色时间为6.94 s, 最大着色效率达到94.04 cm²/C, 实现了从无色、 蓝色到蓝紫色, 再到无色的可逆颜色变化, 相对于单独P₂W₁₅V₃膜, 光反差提高46.07%, 着色效率提高96.53%, 电致变色性能显著提高.     

石墨烯-ITO复合电极对聚苯胺薄膜电致变色性质的影响

采用改进的Hummers法制备氧化石墨烯(GO),首先,石墨与浓硫酸、过硫酸钾和五氧化二磷反应制得强氧化产物,随后将其与浓硫酸、硝酸钠、高锰酸钾反应,经双氧水发泡、酸洗、超声等合成氧化石墨烯水溶液,再通过金属箔还原和基底转移过程制备GO-氧化铟锡(ITO)复合电极材料.通过金属箔还原和基底转移过程制备GO-氧化铟锡(ITO)复合电极材料.利用电化学聚合法在GO-ITO复合电极上制备聚苯胺(PANI)薄膜,并对其形貌结构、电化学及电致变色性质进行表征.结果表明,与ITO电极相比,采用GO-ITO复合电极制备的PANI的成膜性得到明显改善,复合电极具有更加均匀细致的颗粒表面,增大了聚合物与电解液之间的接触面积,为电致变色过程中平衡离子的注入/脱出提供了更多的通道,因而PANI薄膜在700nm处的光学对比度提高了约13%,响应速度缩短了约2.6 s,着色效率高达169.6 cm2/C.GO的引入保持了PANI良好的电化学稳定性.GO-ITO复合电极有效改善了聚合物的综合性能,对于聚合物电致变色材料及器件的开发具有潜在的应用前景.     

气液界面法组装的Ni3(HITP)2电致变色薄膜及其性能

由于缺乏可控的成膜技术,三亚苯类金属有机框架(MOFs)材料的应用受到了限制。我们在气液界面组装了不同厚度的Ni₃(HITP)₂薄膜(HITP^3-=2,3,6,7,10,11-六亚氨基三亚苯),并将制备的薄膜转移到导电玻璃表面。利用X射线衍射(XRD)、场发射透射电子显微镜(FETEM)、场发射扫描电镜(FESEM)、X射线光电子能谱(XPS)和拉曼光谱对样品的晶体结构、微观形貌和元素组成进行表征,采用紫外可见分光光度计以及电化学工作站对Ni₃(HITP)₂薄膜的电化学和电致变色性能进行了研究和表征。结果表明,得益于Ni₃(HITP)₂电致变色薄膜的多孔结构和与电解液良好的接触,所得薄膜电极N-20具有较短的着色响应时间/褪色响应时间(0.6/0.7 s),且着色效率可达530 cm²·C^-1;而N-50具有较大的光调制范围(740 nm,70%)。     

氧化铑电致变色薄膜的制备、结构及性能

采用溶胶_凝胶方法在ITO导电基底上制备氧化铑电致变色薄膜 .当在碱性溶液中对薄膜分别施加阴极和阳极电位时 ,薄膜即呈现由亮黄到深绿的可逆变化 .采用原位XRD、TG_DTA、IR、XPS等方法对薄膜的结晶态、热处理过程以及膜的化学组成进行分析 .应用交流阻抗法计算了薄膜变色过程的扩散系数 ,结果表明该膜基本可以用于变色器件     

P2W18O626-@Tb3+溶液电致变色/荧光开关性质的可逆调控及对H2O2的光谱检测

基于功能互补原理,将Dawson型多阴离子P_2W_(18)O_(62)~(6-)可逆的电致变色性质与Tb~(3+)优异的发光性质相结合,在外加氧化还原电位下实现了P_2W_(18)O_(62)~(6-)@Tb~(3+)混合溶液可逆的电致变色及荧光开关性能,考察外加还原电位对电致变色响应时间及荧光开关能量转移效率的影响,在-0.38、-0.69、-0.85 V下混合溶液的能量转移效率分别为85.97%、87.53%、93.42%。在此基础上,将电化学还原与化学氧化相结合实现了P_2W_(18)O_(62)~(6-)@Tb~(3+)混合溶液对H_2O_2紫外可见、荧光双光谱检测,紫外可见、荧光光谱法对H_2O_2的检出限分别为1.76×10~(-2)、3.04μmol·L~(-1)。     

Sol-Gel Derived Hydrated Nickel Oxide Electrochromic Films: Optical, Spectroelectrochemical and Structural Properties

Electrochromic hydrated Ni-oxide films were prepared using a dip-coating technique from a nickel sulphate heptahydrate precursor in combination with glycerol, formamide and polyvinyalcohol. In-situ monochromatic (λ=400 nm) spectroelectrochemical measurements using a potential of −0.4 V to 0.8 V in 0.1M LiOH electrolyte revealed that the electrochromic efficiency was 23.5 cm²/C. The observed colouring/bleaching transmittance of a 100 nm thick film changed during potential cycling (20 cycles) by 45%. Ex-situ FT-IR absorption/reflection measurements performed at near-grazing incidence angle conditions (80°) confirmed transformation of as-deposited α-Ni(OH)₂ phase to β-Ni(OH)₂ at cathodic (bleached state) and β-NiOOH at anodic (coloured state) potentials during extended cycling (200 cycles). Clear evidence of the OH⁻ ions insertion and release of SO ₄ ²⁻ ions from the as-deposited films when soaked (0.5 hour) in 0.1M LiOH are given. These processes are accompanied by the transformation of the residual COO⁻ groups originating from the peptisation with glacial acetic acid into CO ₃ ²⁻ species residing in the films during extensive potential cycling.     

Nanohybridization of CoS2/MoS2 Heterostructure with Polyoxometalate on Functionalized Reduced Graphene Oxide for High-Performance LIBs

To address the poor cycling stability and low rate capability of MoS₂ as electrode materials for lithium-ion batteries (LIBs), herein, the CoS₂/MoS₂/PDDA-rGO/PMo₁₂ nanocomposites are constructed via a simple hydrothermal process, combining the advantages of all three, namely, CoS₂/MoS₂ heterojunction and polyoxometalates (POMs) provide abundant catalytically active sites and increase the multi-electron transfer ability, and the positively charged poly(diallyldimethylammonium chloride) modified reduced graphene oxide (PDDA-rGO) improve electronic conductivity and effectively prevent the aggregation of MoS₂, meanwhile stabilize the negatively charged [PMo₁₂O₄₀]³⁻. After the electrochemical testing, the resulting CoS₂/MoS₂/PDDA-rGO/PMo₁₂ nanocomposite achieved 1055 mA h g⁻¹ initial specific capacities and stabilized at 740 mA h g⁻¹ after 150 cycles at 100 mA g⁻¹ current density. And the specific capacities of MoS₂, MoS₂/PDDA-rGO, CoS₂/MoS₂, and CoS₂/MoS₂/PDDA-rGO were 201, 421, 518, and 589 at 100 mA g⁻¹ after 150 cycles, respectively. The fact of the greatly improving capacity of MoS₂-based nanocomposites suggests its potential for high performance electrode materials of LIBs. Moreover, the lithium storage mechanism of CoS₂/MoS₂/PDDA-rGO/PMo₁₂ has been discussed on the basis of cyclic voltammetry with different scan rates.     

The Role of Oxidative Debris on Graphene Oxide Films

We study the effect of oxidative impurities on the properties of graphene oxide and on the graphene oxide Langmuir–Blodgett films (LB). The starting material was grupo Antolín nanofibers (GANF) and the oxidation process was a modified Hummers method to obtain highly oxidized graphene oxide. The purification procedure reported in this work eliminated oxidative impurities decreasing the thickness of the nanoplatelets. The purified material thus obtained presents an oxidation degree similar to that achieved by chemical reduction of the graphite oxide. The purified and non‐purified graphene oxides were deposited onto silicon by means of a Langmuir–Blodgett (LB) methodology. The morphology of the LB films was analyzed by field emission scanning microscopy (FE‐SEM) and micro‐Raman spectroscopy. Our results show that the LB films built by transferring Langmuir monolayers at the liquid‐expanded state of the purified material are constituted by close‐packed and non‐overlapped nanoplatelets. The isotherms of the Langmuir monolayer precursor of the LB films were interpreted according to the Volmer’s model.     

The Influence of Lateral Size and Oxidation of Graphene Oxide on Its Chemical Reduction and Electrical Conductivity of Reduced Graphene Oxide

The chemical reduction efficiencies of graphene oxide (GO) are critically important in achieving graphene-like properties in reduced graphene oxide (rGO). In this study, we assessed GO lateral size and its degree of oxidation effect on its chemical reduction efficiency in both suspension and film and the electrical conductivity of the corresponding rGO films. We show that while GO-reduction efficiency increases with the GO size of lower oxidation in suspension, the trend is opposite for film. FESEM, XRD, and Raman analyses reveal that the GO reduction efficiency in film is affected not only by GO size and degree of oxidation but also by its interlayer spacing (restacking) and the efficiency is tunable based on the use of mixed GO. Moreover, we show that the electrical conductivity of rGO films depends linearly on the C/O and Raman I_D/I_G ratio of rGO and not the lateral size of GO. In this study, an optimal chemical reduction was achieved using premixed large and small GO (L/SGO) at a ratio of 3:1 (w/w). Consequently, the highest electrical conductivity of 85,283 S/m was achieved out of all rGO films reported so far. We hope that our findings may help to pave the way for a simple and scalable method to fabricate tunable, electrically conductive rGO films for electronic applications.     

Electrochemical and Structural Characterisation of Dip-Coated Fe/Ti Oxide Films Prepared by the Sol-Gel Route

Thin solid films of mixed Fe/Ti oxide composition (Fe/Ti molar ratios: 0.5∶1, 1∶1, 1.5∶1) have been made from Fe(NO₃)₃ alcoholic solution to which Ti(OiPr)₄ was added. Films have been deposited by the dip-coating technique and heat-treated at 300°C and 500°C. Powders of Fe/Ti oxide heat-treated at 300°C are amorphous, while powders annealed at 500°C for 40 hours transformed to mixed rutile, pseudobrookite and hematite phases. The structure of the XRD amorphous films was identified with the help of near-normal reflection absorption (6°) (IRRA) and near-grazing incidence angle (NGIA) spectroscopy. NGIA FT-IR spectra of films are characterised with a single phonon mode appearing in the spectral range 600–950 cm⁻¹ which shifts with increasing Ti concentration from 675 cm⁻¹ (Fe₂O₃) to 904 cm⁻¹ (TiO₂) thus exhibiting one-mode behavior. Electrochemical investigations made with the help of cyclic voltammetry (CV) and chronocoulometry (CPC) performed in 0.01M LiOH and in 1M LiClO₄/propylene carbonate electrolytes revealed that films are able to uptake reversibly Li⁺ ions with a charge capacity (Q) per film thickness (d) in the range 0.1–0.26 mC/cm²nm and 0.06 mC/cm²nm, respectively. The temperature at which the films were prepared alters the rate of Li⁺ insertion which is faster for less compact films obtained at 300°C. In situ UV-VIS spectroelectrochemical measurements revealed that Fe/Ti oxide films bleached in the UV spectral region (300 nm<λ<450 nm) and colored in the VIS spectral region (450 nm<λ<800 nm), thus exhibiting mixed anodic and cathodic electrochromism.     

部分还原氧化石墨烯/二氧化钛复合材料的水热合成及其光催化活性

采用水热法以Hummers氧化法制备的氧化石墨和钛酸四丁酯为原料制备了部分还原的氧化石墨烯/二氧化钛(RGO/TiO₂)复合光催化剂, 并研究了该复合材料在可见光以及紫外光下对亚甲基蓝的光催化降解活性.结果表明, 通过改变反应温度和氧化石墨加入量可以调控TiO₂的晶相组成及其在复合材料中的分散性; 在水热反应过程中氧化石墨烯发生了部分还原; 所制备的RGO/TiO₂复合材料的可见光和紫外光催化活性均高于纯TiO₂; 部分还原的氧化石墨烯在复合材料中担当载体和电子受体, 同时可以使TiO₂的初始吸收边向可见光区域红移, 增强了TiO₂在可见光区域的吸收, 能有效提高对目标污染物的吸附性和光催化降解活性.     

新型十二烷基三甲氧基硅烷/氧化石墨烯复合膜对430不锈钢耐蚀性能的影响

使用一步电沉积法在430不锈钢上制备出十二烷基三甲氧基硅烷(DTES)/氧化石墨烯(GO)复合膜。 拉曼光谱(Raman)与扫描电子显微镜(SEM)测试表明,氧化石墨烯均匀地混合在硅烷膜中,并用电化学交流阻抗与极化曲线方法对这种复合膜所保护的430不锈钢进行耐蚀性能测试。 结果显示,在3.5%NaCl溶液中,430不锈钢会发生腐蚀反应,而存在硅烷复合膜的430不锈钢的耐蚀性能显著地提高。 研究表明,由于氧化石墨烯出色的阻隔性能一定程度上弥补了硅烷膜的缺陷,而且延长了腐蚀介质通过硅烷基质的路径,因此复合膜有着对基底物质更强的保护性能。