新型不对称双季铵盐缓蚀剂在HCl中对Q235钢的缓蚀行为

采用静态失重法、极化曲线法和交流阻抗法研究了自制的含咪唑啉环不对称双季铵盐缓蚀剂(DBA)在1 mol•L^－1 HCl介质中对Q235钢的缓蚀性能, 并探讨了其在Q235钢表面的吸附行为. 结果表明, 缓蚀效率随DBA浓度增加而增大, 在25～55 ℃的实验温度范围内, 浓度为2.89×10^－4 mol•L^－1时, 缓蚀效率均在90%以上, 且缓蚀效率随温度升高而增大. 极化曲线测试显示DBA是一种阴极抑制为主的混合型缓蚀剂. 缓蚀剂在Q235钢表面的吸附过程为吸热过程, 其在Q235钢表面的吸附遵循Langmuir等温式, 属于化学吸附. 最后采用量子化学方法对DBA的缓蚀机理做了进一步分析.     

离子液体[Bmim]Cl在H2SO4中对Q235钢的缓蚀实验和理论分析

探究1-丁基-3-甲基-咪唑氯盐([Bmim]Cl)在H_2SO_4介质中对Q235钢的缓蚀性能,解决酸性环境在金属表面造成的腐蚀危害。采用静态缓蚀失重法、电化学法分析了不同浓度[Bmim]Cl对Q235钢的缓蚀性能。Q235钢表面形貌特征以及吸附行为分别采用了扫描电子显微镜(SEM)及吸附等温模型进行了分析。采用理论模拟计算分析了缓蚀剂分子在碳钢表面的缓蚀机理。结果表明,[Bmim]Cl为阴极主导的混合型缓蚀剂,随[Bmim]Cl浓度的增加,缓蚀效果越好,当[Bmim]Cl浓度为0.6 mol·L~(-1)时,缓蚀效率可达91%以上,等温吸附模型证明缓蚀剂分子可自发吸附在金属表面,符合Langmuir等温线。[Bmim]Cl通过化学键与Q235钢表面结合形成了以咪唑杂环为吸附中心、稳定化学吸附的单分子吸附层,且[Bmim]~+平行吸附于表面达到防腐蚀效果。[Bmim]Cl是一种性能优异的防腐蚀剂,能有效预防Q235钢在H_2SO_4介质中的腐蚀。     

山梨酸钾与Zn2+在NaCl溶液中对Q235钢的缓蚀协同作用

采用失重法、电化学法、X射线光电子能谱(XPS)和扫描电子显微镜(SEM)研究了0.5 mol/L NaCl溶液中,山梨酸钾(PS)与Zn²⁺对Q235钢的缓蚀协同效应。 失重实验结果表明,在0.5 mol/L NaCl溶液中,PS对Q235钢具有一定的缓蚀效果,缓蚀效率随PS质量浓度的增加而增大,当添加PS的质量浓度为25.0 g/L时,最大缓蚀效率仅为38.37%,而PS与Zn²⁺复配后存在显著的缓蚀协同作用,缓蚀效率高达91.03%。 动电势极化结果表明,PS与Zn²⁺混合物可同时抑制Q235钢的阴、阳极反应,属于阳极型缓蚀剂。 阻抗谱表明,该混合物可在电极表面形成致密的保护膜。 XPS分析证明保护膜是由PS、铁的氧化物/氢氧化物和Zn(OH)₂沉淀组成。     

甲硫氨酸对碳钢在硫酸介质中的缓蚀作用

应用动电位极化法和量子化学计算研究了甲硫氨酸在10％H2SO4溶液中对碳钢的缓蚀性能.电化学测试表明:甲硫氨酸对碳钢在10％H2SO4溶液中具有较好的缓蚀作用,随甲硫氨酸浓度的增加,缓蚀效率增大,随温度的增加,缓蚀效率减小；甲硫氨酸属于典型的混合抑制型缓蚀剂,作用机理为几何覆盖效应；甲硫氨酸在碳钢表面的吸附为单分子吸附...     

新型咪唑啉化合物在H_2S/CO_2共存条件下对Q235钢的缓蚀性能

合成了一种新型咪唑啉化合物1-(2-氨基-硫脲乙基)-2-十五烷基-咪唑啉(IM-S),并通过失重法、电化学方法及扫描电镜等研究了IM-S在H2S/CO2共存条件下对Q235钢的缓蚀性能,探讨了其在Q235钢表面的吸附行为.结果显示,IM-S具有较好的抗H2S、CO2腐蚀能力,能同时抑制碳钢腐蚀的阴、阳极反应过程,最高缓蚀效率可达92.74%.缓蚀剂在Q235钢表面呈单分子层吸附,属于以化学吸附为主的混合吸附.最后采用量子化学方法对IM-S的缓蚀机理做了进一步分析.     

1,2-二(苯并咪唑-2-基)乙醇的合成及其对Q235钢的缓蚀性能研究

通过DL－苹果酸与邻苯二胺以盐酸盐形式在乙二醇中发生缩合反应,合成了一种双苯并咪唑化合物二(2-苯并咪唑)乙醇(HbbImet),采用静态失重法、极化曲线法和电化学阻抗谱研究了HbbImet在0.5mol/L的盐酸溶液中对Q235钢的缓蚀性能,并探讨了缓蚀机理。结果表明,同一温度条件下HbbImet的缓蚀效率随其浓度的增加而增大,同一浓度条件下HbbImet的缓蚀效率温度的升高而减小。25℃下当HbbImet浓度为120mg/L时,其缓蚀效率可达92.23%,具有良好的缓蚀性能。HbbImet的添加显著增大了腐蚀反应的表观活化能,有效抑制了腐蚀反应的进行,是一种以控制阴极析氢过程为主的混合型缓蚀剂。     

2-氨基嘧啶在盐酸介质中对钢的缓蚀性能

用失重法、动电位极化曲线和电化学阻抗谱（EIS）研究了2-氨基嘧啶(2-AP)在1.0~5.0 mol/L HCl溶液中（20~50 ℃）对冷轧钢的缓蚀作用。 结果表明,2-AP对冷轧钢在1.0 mol/L HCl中具有良好的缓蚀作用,且在钢表面的吸附符合校正的Langmuir吸附模型;缓蚀率随缓蚀剂浓度的增加而增大,但随温度的升高和HCl浓度的增加而降低。 2-AP为混合抑制型缓蚀剂;EIS谱呈半圆容抗弧,电荷转移电阻随缓蚀剂浓度的增加而增大。     

咪唑啉衍生物缓蚀剂对碳钢在CO2盐水中的缓蚀机理

采用极化曲线和交流阻抗研究新合成咪唑啉衍生物缓蚀剂对碳钢在饱和CO2盐水中的缓蚀性能和机理. 计算了缓蚀效率和热力学参数. 缓蚀效率随着缓蚀剂浓度增大而增加, 但随着温度增加先增加后降低. 咪唑啉衍生物在碳钢表面的吸附符合Langmuir等温式. 电化学结论由量子化学计算补充说明.     

1,2-二(苯并咪唑-2-基)乙醇的合成及其对Q235钢的缓蚀性能研究

通过DL-苹果酸与邻苯二胺盐酸盐在乙二醇中发生缩合反应,合成了一种双苯并咪唑化合物1,2-二(苯并咪唑-2-基)乙醇(Hbb Imet),采用静态失重法、极化曲线法和电化学阻抗谱研究了Hbb Imet在0.5mol/L的盐酸溶液中对Q235钢的缓蚀性能,并探讨了缓蚀机理。结果表明,25℃下Hbb Imet的缓蚀效率随其浓度的增加而增大,当Hbb Imet浓度为120mg/L时,其缓蚀效率可达92.23%,具有良好的缓蚀性能。Hbb Imet的添加显著增大了腐蚀反应的表观活化能,有效抑制了腐蚀反应的进行,是一种以控制阴极析氢过程为主的混合型缓蚀剂。     

甲基丙烯酸二甲氨基乙酯类离子液体 对Q235钢的缓蚀性能

以甲基丙烯酸二甲氨基乙酯为母体、 对氯甲基苯乙烯为季铵化试剂, 合成了一种具有疏水结构的甲基丙烯酸二甲氨基乙酯型离子液体(DEMA). 通过失重实验、 电化学分析、 原子力显微镜(AFM)、 接触角测试和量子化学计算等研究了DEMA在1 mol/L盐酸中对Q235钢的缓蚀性能, 并揭示了其在Q235钢表面的吸附行为和吸附机理. 失重实验结果表明, DEMA在盐酸中对Q235钢具有优异的缓蚀效果, 且在较高温度(60 ℃)下也能保持高效吸附; 电化学实验结果与失重测试结果一致; 接触角测试结果表明, DEMA可明显增强Q235钢表面的疏水性; 分析热力学参数可知, DEMA在Q235钢表面的吸附为自发、 放热过程, 符合Langmuir等温式, 且以化学吸附为主; 量子化学计算结果证实DEMA的结构中包含大量吸附活性位点.     

盐酸介质中水杨醛缩氨基硫脲对碳钢的缓蚀作用

合成了新型席夫碱缓蚀剂:水杨醛缩氨基硫脲(ST),并考察了其在1 mol/L盐酸溶液中对碳钢的缓蚀性能。通过静态失重、动电位极化曲线、交流阻抗等技术手段研究缓蚀剂浓度对腐蚀速率及缓蚀效率的影响,阐明缓蚀作用机理。结果表明,ST在盐酸介质中对碳钢具有良好的缓蚀性能。随着缓蚀剂浓度的增加,缓蚀效率逐渐增大。ST的加入显著降低了自腐蚀电流密度,为抑制阴极反应为主的缓蚀剂。ST在碳钢表面的吸附符合Langmuir吸附模型,为物理吸附与化学吸附共同作用。     

Adsorption Activity and Molecular Dynamics Study on Anti-corrosion Mechanism of Q235 Steel

The correlation between inhibition efficiency and molecular structures of the inhibitor during hydrochloric acid corrosion of Q235 steel was studied by quantum chemical calculations and molecular dynamics(MD) simulation. The proton affinity(PA) calculations demonstrated that 2-(quinolin-2-yl)quinazolin-4(3H)-one inhibitor has the tendency to be protonated in hydrochloric acid, which was in good agreement with experimental observations. Besides, quantum chemical parameters revealed that the protonated corrosion inhibitor molecules were more easily adsorbed on Q235 steel surface and improved the corrosion resistance of steel. MD simulations were implemented to search for the adsorption behavior of this molecule on Fe (110) surface, which might be used as a convenient tool for estimating the interaction mechanism between inhibitor and iron surface.     

MPEC-IMI as an effective green inhibitor to protect Q235 steel in 0.5 M HCl medium

Imidazole (IMI)-based polyethylene glycol monomethyl ether (MPEC-IMI) as a novel green corrosion inhibitor was synthesized to protect the Q235 steel in 0.5 M HCl corrosive medium at 318 K. The inhibition performance of MPEC-IMI was investigated by weight loss measurement, the electrochemical method (Tafel and EIS) and surface analysis (SEM and EDX). The results reveal that the MPEC-IMI shows enhanced anticorrosion performance for carbon steel, which is attributed to the formation of the adsorptive protection film on the surface, and the type of adsorption basically obeys the Langmuir monolayer adsorption. Furthermore, when the concentration of MPEC-IMI is 300 mg L^?1, the corrosion inhibition efficiency can reach up to 92.00%. In support of further study of the corrosion inhibition behavior by virtue of quantum chemical calculation and molecular dynamics simulations, the results show that the MPEC-IMI molecule has high reactivity and strong interaction on the iron surface.     

喹啉型双子季铵盐缓蚀剂的实验及理论分析

以喹啉为母体、 1,4-对二氯苄和顺-1,4-二氯-2-丁烯为联结基, 制备了2种具有疏水结构的水溶性双喹啉季铵盐(BQA-1和BQA-2). 通过失重实验、 电化学测试、 扫描电子显微镜(SEM)及量子化学计算等手段研究了BQA-1和BQA-2对1 mol/L盐酸中Q235钢的缓蚀性能, 并讨论了其在Q235钢表面的吸附机理. 失重结果显示, BQA-1和BQA-2对盐酸中的钢片均具有良好的缓蚀效果, 30 ℃下, 当浓度为0.5 g/L时, BQA-1和BQA-2的缓蚀率均超过94.59%; 升温导致BQA-2的脱附速率比BQA-1更快. 电化学测试结果显示, BQA-1和BQA-2是以抑制阴极为主的混合型缓蚀剂. 分析热力学参数可知, BQA-1和BQA-2在钢表面的吸附为自发、 放热过程, 符合Langmuir等温式, 且以化学吸附为主. 量子化学计算结果表明, BQA-1和BQA-2的吸附活性集中在喹啉环及杂原子上, 且BQA-1和BQA-2分子得电子与Fe作用的能力要强于供电子与Fe作用的能力.     

Structure,Anticorrosion and Antibacterial Evaluation of (<Emphasis Type="Italic">E</Emphasis>)-3-(<Emphasis Type="Italic">N</Emphasis>-Oxide-methylimino)indolin-2-one

A nitrone, (E)-3-(N-oxide-methylimino)indolin-2-one, was synthesized and analyzed by X-ray single crystal analysis. The inhibition and the mechanism of action of the title compound on the corrosion of high protective Q235A steel in HCl solution were screened and discussed by weight loss and electrochemical measurements. The mechanism of action of (E)-3-(N-oxide-methylimino)indolin-2-one in HCl solution was screened for the corrosion of N80 steel in 1-methylindolin-2-one solution, and the inhibition mechanism was discussed. The results indicated that it can inhibit the corrosion with moderate inhibition efficiency in different conditions, and the mechanism of the corrosion inhibiting may be mainly contributed to the adsorption. It was screened for antibacterial activity against oilfield water-borne bacteria, and it showed good to moderate activity against sulfate reducing bacteria.     

分子结构对咪唑啉缓蚀剂膜在Q235钢表面生长和衰减规律的影响

采用弱极化法、电化学阻抗谱等手段研究了烷基咪唑啉和硫脲基烷基咪唑啉缓蚀剂对Q235钢在饱和CO2盐溶液中的缓蚀行为变化, 探讨了吸附膜的形成与衰减规律. 结果表明, 烷基咪唑啉和硫脲基烷基咪唑啉缓蚀剂都是以控制阳极过程为主的混合界面型缓蚀剂. 在85 ℃下, 烷基咪唑啉成膜相对较慢, 吸附能力较弱, 容易发生脱附; 而硫脲基的引入, 使得硫脲基烷基咪唑啉缓蚀剂溶液存在自动修复能力, 增强了咪唑啉环的吸附性能, 提高了缓蚀剂的缓蚀性能; 硫脲基烷基咪唑啉水解开环后, 成膜性能下降, 膜寿命和缓蚀效率也大大降低. 最后采用量子化学计算对上述结论进行了验证和解释.     

辛烷基二甲基苄基季铵盐离子液体对Q235钢的缓蚀性能

利用失重分析、 极化曲线、 电化学阻抗谱和扫描电子显微镜等研究了辛烷基二甲基苄基季铵盐离子液体(ODBA)对1 mol/L盐酸溶液中Q235钢的缓蚀性能, 并分析了其在Q235钢表面的吸附行为. 失重分析结果表明, 随着ODBA浓度的增加, 缓蚀效率逐渐提高, 在ODBA质量浓度为0.2 g/L、 温度为30 ℃时, 缓蚀效率可达95.53%; 电化学测试结果与失重分析结果一致; 热力学研究结果表明, ODBA在碳钢表面的吸附是放热过程, 且遵循Langmuir吸附等温线, 是以化学吸附为主的混合型吸附; 同步热分析测试表明ODBA具有良好的热稳定性.     

Role of novel oxazocine derivative as corrosion inhibitor for 304 stainless steel in acidic chloride pickling solutions

Inhibition of 304 stainless steel corrosion in acidic chloride pickling (1.0 M HCl) solutions by newly synthesized oxazocine derivative 4 as a corrosion inhibitor have been studied using weight loss, potentiodynamic polarization, and atomic absorption spectroscopy investigations. Potentiodynamic polarization curves show that the inhibitor behaves as a mixed-type. The adsorption of the inhibitor on the metal surface in the acid solution was found to obey Langmuir’s adsorption isotherm. The inhibition mechanism of the investigated inhibitor was discussed in terms of its adsorption on the metal surface. The relationship between the molecular structure and the inhibition efficiency was elucidated by quantum chemical calculations.     

Study on the corrosion inhibition of biomass carbon quantum dot self- aggregation on Q235 steel in hydrochloric acid

At present, the development of efficient green corrosion inhibitors has become one of the important directions of metal corrosion protection. In this paper, biomass carbon quantum dots (BCQDs) were prepared by hydrothermal reaction using biomass precursors. The optical properties and structural composition of the synthesized BCQDs were characterized in detail. After that, the corrosion inhibition performance of BCQDs was evaluated by EIS, Tafel, SEM and TEM. The electrochemistry and surface tests demonstrate that the aggregates can effectively prevent Q235 steel from corrosion in 1 M HCl medium at 298 K-328 K, with the maximum inhibition efficiency of 94.1 % at the concentration of 200 mg/L at 308 K. Finally, the corrosion inhibition mechanism was analyzed by FTIR, CA and XPS on the surface of the corroded carbon steel samples. The inhibition mechanism suggests that BCQDs can inhibit metal corrosion by self-aggregation and adsorption on metal surface. This is owing to its small size effect and functional groups containing heteroatoms, easily forming dense protective film.