激光法测定硝唑尼特结晶介稳区间

用激光法测定了不同温度下硝唑尼特在N,N-二甲基甲酰胺（DMF）、二甲基亚砜（DMSO）、甲醇和丙酮4种溶剂体系中的溶解度与超溶解度,得到硝唑尼特在不同溶剂和不同温度下的介稳区宽度。 结果表明,硝唑尼特在4种溶剂体系中的溶解度、超溶解度和介稳区宽度随温度升高逐渐增大。 在相同温度下,硝唑尼特在DMF、DMSO、甲醇和丙酮中介稳区宽度关系为：丙酮＜DMSO＜甲醇＜DMF。     

不同浓度KCl和NH4Cl溶液中H3BO3介稳区的性质

测定了H3BO3在0~25 ℃内于不同浓度KCl和NH4Cl溶液中的溶解度和超溶解度, 得到了H3BO3的介稳区宽度, 并推算出表观成核级数m, 给出了成核速率方程. 研究了KCl和NH4Cl对H3BO3介稳区性质的影响, 并对影响的机理进行了探讨. 结果表明, KCl使H3BO3介稳区向低温方向移动; NH4Cl使H3BO3介稳区向高温方向移动; 根据所得结论分析了KCl和NH4Cl在柴达木西部油田水析硼过程中的影响, 认为KCl和NH4Cl在蒸发过程中浓度的变化是造成硼分散析出而不能富集的因素之一.     

钴胺素溶析结晶过程及离子杂质对其晶体生长的影响

采用激光法研究了钴胺素的结晶过程热力学,考察了温度、溶剂对溶解度和超溶解度的影响,并测定了介稳区,介稳区的宽度随体系中丙酮含量的减小而变宽. 研究了离子杂质Na+、Mg2+、Ca2+和Fe3+对钴胺素结晶诱导期的影响. 结果表明,离子的存在使得晶体更容易出现断裂和聚结,并用扫描电子显微镜测试技术对晶体的表面形貌进行了表征. 结果表明,Fe3+、Mg2+比Na+、Ca2+影响更明显.     

Li^+, Mg^2^+/Cl^-, SO4^2^——H2O四元体系(25℃)的介稳平衡

本文用等温蒸发的方法, 研究了Li^+, Mg^2^+//Cl^-,SO4^2^--H2O体系(25℃)介稳相平衡, 绘制了介稳相图, 测定了密度、粘度、折光率、电导率和某些液相点的蒸汽压。该介稳相图由六个结晶区构成, 即LiCl·H2O、LiCl·MgCl2·7H2O、MgCl2·6H2O、Li2SO4·H2O、MgSO4·7H2O和MgSO4·6H2O相区。该体系的25℃介稳相图和稳定相图的差异是, 新结晶区MgSO4·6H2O的出现, 使LiSO4·H2O相区扩大, 其它相区缩小。根据Pitzer电解质溶液理论, 用单纯形法在M68000计算机上进行了体系溶解度关系的计算,并获得了计算的溶解度数据, 绘 制了计算的相     

Li^+, Mg^2^+/Cl^-, SO4^2^——H2O四元体系(25℃)的介稳平衡

本文用等温蒸发的方法,研究了 Li~+,Mg~(2+)∥Cl~-,SO_4~(3-)-H_2O 体系(25℃)介稳相平衡,绘制了介稳相图,测定了密度、粘度、折光率、电导率和某些液相点的蒸汽压.该介稳相图由六个结晶区构成,即 LiCl·H_2O、LiCl·MgCl_2·7H_2O、MgCl_2·6H_2O、Li_2SO_4·H_2O、MgSO_4·7H_2O 和 MgSO_4·6H_2O相区.该体系的25℃介稳相图和稳定相图的差异是,新结晶区 MgSO_4·6H_2O 的出现,使 Li_2SO_4·H_2O 相区扩大,其它相区缩小.根据 Pitzer 电解质溶液理论,用单纯形法在 M68000计算机上进行了体系溶解度关系的计算,并获得了计算的溶解度数据,绘制了计算的相图.     

Li~ ,Na~ //SO_4~(2-),B_4O_7~(2-)-H_2O交互四元体系288K介稳相平衡研究

采用等温蒸发法研究了四元体系Li ,Na //SO42-,B4O72--H2O288K介稳相平衡及平衡液相物化性质(密度、电导率、折光率、粘度和pH值),测定了该四元体系288K条件下介稳平衡溶液溶解度及物化性质。根据实验数据绘制了相应的介稳相图及物化性质组成图。研究发现:该体系介稳平衡中有复盐Li2SO·4Na2SO4形成。其介稳相图中有3个共饱和点,7条单变量曲线,平衡固相为:Li2SO·4H2O,Na2SO4,Li2SO·4Na2SO4,Li2B4O7·3H2O,Na2B4O·710H2O。复盐Li2SO·4Na2SO4和一水硫酸锂(Li2SO·4H2O)有较小的结晶区,而Li2B4O7·3H2O和Na2B4O7·10H2O有较大的结晶区;该四元体系介稳平衡条件下未发现Na2SO·410H2O的结晶区。     

钴胺素的溶析结晶研究以及离子杂质对晶体生长的影响

采用激光法研究了钴胺素的结晶热力学,包括在不同温度下,不同溶剂配比下的溶解度和超溶解度,介稳区的测定。研究了四种不同的离子杂质(Na+,Mg2+,Ca2+and Fe3+)对钴胺素结晶诱导期的影响。通过实验结果表明钴胺素在溶析结晶过程中,Fe3+和Mg2+要比Na+和Ca2+具有更明显的影响。     

五元体系Li+,Na+//CO32-,So42-,B4O72-H2O 288 K介稳相平衡研究

采用等温蒸发法研究五元体系Li+,Na+//CO32-,SO42-,B4O72--H2O 288 K介稳相平衡关系,测定在288 K条件下的介稳平衡溶液中各组分的溶解度和溶液密度,根据实验数据绘制相应的介稳平衡相图及密度组成图.研究结果表明该五元体系介稳相平衡中有复盐Na3Li(SO4)2·6H2O生成,其介稳相图中有4个共饱点,9条单变量曲线,6个Li2CO3饱和的结晶区分别为LiBO2·8H2O,Na284O7·10H2O,Na2CO3·10H2O,Na2SO4,Li2O4·H2O和复盐Na3Li(SO4)2·6H2O.     

Na+, K+//Cl-, B4O2-7-H2O四元体系273 K介稳相平衡

采用等温蒸发法研究了四元体系Na+, K+//Cl-, B4O2-7-H2O 273 K时的介稳相平衡与相图. 测定了该体系273 K平衡液相中各组分的溶解度及平衡液相的密度; 绘制了该体系的介稳相图. 该四元体系273 K相图由5条溶解度单变量线、4个结晶区及2个共饱和点组成. 体系无复盐或固溶体形成. 四个结晶区分别对应单盐NaCl、KCl、K2B4O7·4H2O 和Na2B4O7·10H2O. 共饱点E1处KCl、NaCl及Na2B4O7·10H2O三盐共饱和,所对应的平衡液相组成为w(Cl-)=29.15%, w(B4O2-7)=0.64%, w(K+)=5.97%, w(Na+)=15.55%; 共饱和点E2处盐KCl、Na2B4O7·10H2O和K2B4O7·4H2O的三盐共饱和, 所对应的平衡液相组成为w(Cl-)=22.84%, w(B4O2-7)=10.98%, w(K+)=28.01%, w(Na+)=1.53%. 同体系298 K时的稳定相图相比, 273 K时硼酸钠的结晶区变大, 而硼酸钾、氯化钠结晶区变小.     

五元体系Li~+,K~+//CO_3~(2-),SO_4~(2-),B_4O_7~(2-) -H_2O在288 K时的介稳相平衡研究

采用等温蒸发法研究了五元体系Li~+,K~+//CO_3~(2-),SO_4~(2-),B_4O_7~(2-) -H_2O在288 K时的介稳相平衡关系,测定了该五元体系在288 K条件下的介稳平衡的溶解度和溶液密度,根据实验数据绘制了相应的介稳平衡相图和水图,相平衡研究结果表明该五元体系介稳相平衡中有复盐K_2SO_4·Li_2SO_4生成,其介稳相图(Li_2CO_3饱和)有4个共饱和点,9条单变量曲线,6个Li_2CO_3饱和的结晶区分别为LiBO_2·8H_2O,K_28_4O_7·4H_2O,K_2CO_3·3/2H_2O,K_2SO_4,Li_2SO_4·H_2O和复盐K_2SO_4·Li_2SO_4.     

Novel Phenomena of Crystallization and Emulsification of Hydrophobic Solute in Aqueous Solution

Emulsification of lauric acid in an aqueous ethanol solution including lauric acid solute has been observed during cooling before crystallization of lauric acid occurs. The nature of two different solubility curves was explained for the system of lauric acid and aqueous ethanol solution. The mutual solubility of the two liquid phases controls emulsification; the solid solubility of lauric acid controls crystallization. The mutual solubility curve appears at relatively high temperature, and the solid solubility curve at relatively low temperature. Crystallization essentially generates a solid metastable zone under the solid solubility curve. A supersaturated solution can be obtained in the metastable zone. However, no nucleation occurs in the metastable zone. The metastable zone, therefore, still caused emulsification at low temperature before crystallization of lauric acid occurred. The hypothetical mutual solubility curve for the aqueous solution including hydrophobic solutes appeared invariably even at low temperature in the metastable zone under the solid solubility. Copyright 2001 Academic Press.     

Effects of different temperatures and additives on the metastable zone width precipitation kinetics of NaBO2

In this study, the sodium metaborate, which is applicable in various industrial areas, and its metastable zone width that is very important for its production by crystallization, and its nucleation are investigated to obtain the necessary thermodynamic parameters. The polythermal and isothermal method has been used for the measurement of metastable zone width. Metastable zone width of NaBO₂ has found at 9°C at average and cooling rate do not have any effect on it. In addition, the effect of sodium metaborate on the hydrogen storage capacity of sodium borohyride solutions that is known as one of the best hydrogen sources today is investigated at the various concentrations of sodium borohyride in the medium. Results have shown that three different areas emerged as the percentage of NaBH4 in the solution increased.     

A new reagent pair sodium percarbonateacetic anhydride for epoxidation of olefins

A new convenient method for epoxidation of olefins by sodium percarbonate — acetic anhydride is reported. It is found that the epoxides in 60–80% yields can be obtained in 18–24 h without ultrasonication. However, higher yields (some nearly quantitative) can be reached only within 1–3 h under ultrasonication. A comparison between the ultrasonicated epoxidations by use of sodium percarbonate and sodium perborate is also made. The experimental results have revealed that ultrasonication plays a main role in accelerating the interaction of both sodium percarbonate and sodium perborate with acetic anhydride, but it does not alter the mechanism of these two epoxidations.     

Effect of magnetic field on sodium arsenate metastable zone width and crystal nucleation kinetics for crystallization

Sodium arsenate, the main component of arsenic-containing solid waste pollutants, causes serious environmental health threats. Crystallization is one of the effective methods for separating and purifying sodium arsenate from arsenic-alkali residue lixivium. However, the crystallization process is limited for its low observability and the lack of separation and purification data. In this work, a laser detection system with a magnetic field generator was designed, and the solubility, metastable zone width, interfacial tension, interfacial entropy factor, crystal nucleation, and growth rate of sodium arsenate were investigated in a constant composition environment. The results showed that the solubility, metastable zone width, interfacial tension, and interfacial entropy factor decreases with the presence of a magnetic field. The magnetic field shortened the crystallization induction time and changed the nucleation and growth rate of sodium arsenate. Under the magnetic field, the nucleation rate increased from 2.43 × 10¹⁶ to 8.98 × 10¹⁷ (s m³)⁻¹, and the growth rate decreased from 4.94 × 10⁻⁸ to 2.73 × 10⁻⁸ (s m³)⁻¹, the growth mechanism of sodium arsenate as a continuous growth mode was unchanged. In addition, the X-ray diffraction and infrared showed that the crystal structure of sodium arsenate is unaffected by the magnetic field, indicating that the enhancement of the crystallization process of sodium arsenate with the magnetic field could be a feasible method in engineering application.     

Unusual vesicle-micelle transitions in a salt-free catanionic surfactant: temperature and concentration effects

The spontaneous formation of vesicles by the salt-free surfactant hexadecyltrimethylammonium octylsulfonate (TASo) and the features of an unusual vesicle-micelle transition are investigated in this work. In a previous work, we have shown that this highly asymmetric catanionic surfactant displays a rare lamellar miscibility gap in the concentrated regime. Here, we analyze in detail the aggregation behavior in the dilute regime (less than 3 wt % surfactant) as a function of both concentration and temperature. The phase diagram is dominated by a two-phase region consisting of a dispersion of a swollen lamellar phase (Lalpha') in the excess solvent phase (L1). Stable vesicles form in this two-phase region, and upon temperature increase, a transition to a single solution phase containing only elongated micelles occurs. The structural characterization of the aggregates and the investigation of their equilibrium properties have been carried out by light microscopy, cryo-TEM, water self-diffusion NMR, and SANS. Similarly to the lamellar-lamellar coexistence, the changes in microstructure at high dilution and high temperature can be understood from solubility differences, electrostatic interactions, and preferred aggregate curvature. Surface charge in the aggregates stems from the higher solubility of the octylsulfonate (So-) ion as compared to that of the hexadecyltrimethylammonium ion (TA+). Upon temperature increase, the ratio of free So(-) relative to the neutral TASo increases. Consequently, the surface charge density of the aggregates increases, and this ultimately induces a transition to a higher-curvature morphology (elongated micelles). Vesicles can also be spontaneously formed by cooling solutions from the micellar region, and the mean size obtained is practically independent of cooling rate, suggesting that dissociation/charge effects also control this process.     

低温下生物柴油的胶凝特性研究

利用流变仪在小振幅振荡剪切模式下对地沟油、花生油和大豆油生物柴油的胶凝特性进行了研究。结果表明,低温下生物柴油不仅具有冷却胶凝特性,还表现出明显的等温胶凝特性。分析了冷却速率和剪应力对地沟油生物柴油胶凝特性的影响。结果表明,静态降温时降温速率越大,生物柴油的胶凝温度越低,降温及恒温静置过程中同一温度下的胶凝结构越弱。相同降温速率下,生物柴油的胶凝结构和胶凝温度随剪应力的增加而降低,但经受不同剪应力作用的生物柴油恒温静置后胶凝结构相差不大。降温过程中施加的剪应力较小时,冷却胶凝结构随降温速率的增大而降低;剪应力较大时,冷却胶凝结构随降温速率的增大而加强。不管施加的剪应力多大,等温胶凝结构随降温速率的增大而加强。     

Determination and correlation of the solubility of tricin in water and ethanol mixtures

The solubility of tricin in water and ethanol mixtures was measured over the temperature range of (288.15 to 328.15) K. The concentrations of tricin in the aqueous mixtures were assayed by the ultraviolet spectrophotometric method. The experimental solubility data indicated that the solubility of tricin increases with an increase in temperature and an enrichment in ethanol content. The two models, including the modified Apelblat equation and λh equation were used to correlate the experimental solubility data. The calculated solubility of tricin shows good agreement with the experimental results. Additionally, the estimation of thermodynamic properties including the activity coefficients, dissolution enthalpy, and entropy were obtained from the experimental data. Within the studied temperature range the dissolution process of tricin is endothermic, and the driving force is the entropy.     

Crystallization of silver carboxylates from sodium carboxylate mixtures

Silver carboxylates can be made by the reaction of silver nitrate and the corresponding sodium carboxylates. The length of the alkyl chain has a significant impact on the product behavior. In this study, 18, 20, and 22 carbon chains (stearate, arachidate, and behenate, respectively) have been selected. All three sodium carboxylates are very insoluble in water at room temperature. Solutions are obtained above the Krafft temperature, which precipitates lamellar crystals if cooled at the proper cooling rate. Depending on the chain length, metastable morphologies, such as vesicles and tiny fibers, can be seen consecutively before hexagonal plates form. The carboxylate with the shorter chain length reaches equilibrium more quickly. All three silver carboxylates also take on a lamellar structure. Small-angle X-ray scattering (SAXS) shows that the d spacing of the crystals increases as the chain length increases. Cryo-TEM illustrates that the crystallites are the result of micelle nucleation and micelle aggregation. In addition, the crystallization process in the presence of silver bromide nanocrystals has been investigated. In the initial stage, an epitaxial interface is formed between the silver carboxylate crystallites and the cubic silver bromide grains. Budlike and strandlike structures grow because of it. The consequent strand enclosure restrains the crystal growth, which reduces the size and changes the morphology of the crystals.