十二烷基磺酸钠改性蒙脱土的制备与表征

利用阴离子表面活性剂十二烷基磺酸钠(SDS)改性天然蒙脱土，研究了反应介质的酸碱性对插层效果的影响。X射线粉未衍射（XRD）、红外光谱（FT-IR）、热重分析（TGA）表明SDS已插层到蒙脱土片层间，沉降实验和流变学性质研究表明改性后蒙脱土在有机介质中表现出很好的分散性、溶胀性和高触变性。这种改性效果优于目前常用的十六烷基三甲基溴化铵(CTAB)处理效果。解释了阴离子表面活性剂对蒙脱土的插层机理。     

改性蒙脱土吸附2,4-二氯-5-硝基苯酚的研究

分别采用新型双子阳离子表面活性剂Y-16和十六烷基三甲基溴化铵(CTAB)改性钠基蒙脱土,通过IR、TGA、XRD对其进行表征,研究了表面活性剂的浓度、改性蒙脱土的用量以及接触时间对2,4-二氯-5-硝基苯酚(DCNP)吸附的影响。结果表明:上述两种表面活性剂成功插入钠基蒙脱土层间结构且扩大了其层间距。随着表面活性剂的浓度、改性蒙脱土的用量、接触时间的增加,改性蒙脱土对DCNP的吸附量也随之增加,并达到最大值。当采用0.1g 1.8CEC改性蒙脱土且接触时间为180min时,CTAB-MMT和Y-16-MMT对DCNP达到最大吸附量分别为184.84mg·g~(-1)、164.47mg·g~(-1)。改性蒙脱土对DCNP的吸附行为符合二级动力学方程和Langmuir等温吸附方程。     

甲苯-2,4-二异氰酸酯修饰蒙脱土及聚苯乙烯蒙脱土纳米复合材料的制备与表征

用FTIR和WAXD法研究了甲苯-2,4-二异氰酸酯(TDI)的邻位和对位异氰酸酯基团与蒙脱土表面羟基的修饰反应,在此基础上提出了结构模型;用TDI修饰后的蒙脱土成功制备了插层型聚苯乙烯/蒙脱土纳米复合材料,并用WAXD和TEM进行了表征.实验结果表明,修饰后TDI与蒙脱土表面形成化学键,使蒙脱土的片层间距显著增大,十六烷基三甲基溴化铵(CTAB)在蒙脱土层间由双层平行排列转变为双层脂肪链倾斜方式排列.在苯乙烯插层聚合过程中,蒙脱土层间距进一步扩大,其初级粒子在聚苯乙烯基体中的厚度约20～50nm.     

聚苯乙烯/硅烷偶联剂修饰蒙脱土纳米复合材料的制备与表征

用硅烷偶联剂修饰蒙脱土，制备了聚苯乙烯/蒙脱土纳米复合材料，并用XRD、FTIR、TEM和TGA等对样品进行了表征，发现硅烷偶联剂对蒙脱土表面进行了良好的修饰；苯乙烯单体在蒙脱土层间的聚合导致蒙脱土片层剥离并无规分散在聚合物基体中，片层长度为100-200nm，厚度小于10nm。     

sPS/PA6/蒙脱土纳米复合材料的制备与性能

讨论了间规聚苯乙烯 (sPS) 尼龙 6(PA6) 磺化间规聚苯乙烯 (SsPS H) 蒙脱土纳米复合材料的制备技术和新材料的结构与性能特征 .蒙脱土经层间改性处理后 (MTN) ,可分别将SsPS H和aPS(无规聚苯乙烯 )插入其纳米层间 ,制备出插层型纳米复合物MTN SsPS和MTN aPS .在sPS/PA6/SsPS H三组分共混体系中加入MTN SsPS或MTN aPS ,进行四组分熔融共混即可制备出sPS/PA6/SsPS H/蒙脱土纳米复合材料 .TEM测定证实了蒙脱土在基体中的层厚分布约为 5 0nm .此外 ,采用DSC、DMA、XRD及力学性能测试仪等现代分析方法对sPS/PA6/SsPS H/蒙脱土纳米复合材料的结构与性能进行了详细研究 .研究结果表明这种纳米复合材料具有优良的综合性能     

聚N-甲基苯胺/蒙脱土纳米复合材料的合成及其协同电流变效应

用插层聚合法制备了聚N 甲基苯胺 蒙脱土纳米复合材料微粒 ,通过IR、XRD及TEM对其结构进行了表征 .观察发现聚N 甲基苯胺插入蒙脱土层间后 ,蒙脱土片层间距由 0 96nm扩大至 1 34nm .将其分散在甲基硅油中 (2 0wt% )配制成无水电流变液 ,该复合材料表现出显著的协同效应 ,具有较好的电流变行为 .实验表明在电场作用下聚N 甲基苯胺 蒙脱土纳米复合材料的电流变效应比聚苯胺、蒙脱土都有显著提高 ,在 3kV mm(DC ,74 5s- 1 )时 ,剪切强度达 6 0kPa ;同时抗沉降性极好 ,静置 6 0天沉淀率小于 3% .介电性能测试表明聚N 甲基苯胺 蒙脱土纳米颗粒的介电常数和介电损耗较蒙脱土和聚N 甲基苯胺明显提高 ,电导率也达到了最佳范围 .     

新型小分子液晶有机蒙脱土的制备与表征

运用自制的两种新型小分子液晶插层剂对蒙脱土进行有机化修饰,并用IR,XRD,TG及TEM等对有机蒙脱土结构和性能进行了表征与分析。结果表明:有机蒙脱土的层间距由1.00 nm分别增大到2.50 nm和2.88 nm,且能分散均匀,排列疏松,耐热性能也有了显著提高。     

间规聚苯乙烯/尼龙6/磺化间规聚苯乙烯/蒙脱土纳米复合材料的研究

以磺化间规聚苯乙烯（SsPS)为增容剂，将间规聚苯乙烯（sPS)和尼龙6／改性蒙脱土纳米复合物（PA6－MTA）共混，得到综合性能优良的新型多组分聚合物／蒙脱土纳米复合材料（sPS/PA6/SsPS/MTA)。用DSC、DMA、WAXD及力学性能测试仪研究了纳米复合材料的结构与性能。TEM测定证明了蒙脱土在基体中的层厚分布为10－50nm。     

基于胶束插层方法制备高热稳定性和大层间距有机化蒙脱土

采用不同方法制备了多种有机化蒙脱土,并分别采用X射线衍射仪、红外光谱分析仪、热重分析仪、电感耦合等离子体发射光谱仪、元素分析仪、扫描电子显微镜对产物进行了表征,并提出了有机物插层新方式——胶束插层.结果表明:适量钠基蒙脱土(Na-MMT)、十六烷基三甲基溴化铵(CTAB)和磷酸三苯酯(TPP)在丙酮/水的混合溶剂中进行溶液插层,得到的有机化蒙脱土具有更大的层间距,比单纯采用CTAB的插层效果显著.产物中含有约21.54%的CTAB和17.47±1.05%的TPP,插层机理为CTAB-TPP胶束插层.该有机化蒙脱土的初始热降解温度比单纯CTAB插层蒙脱土最多提高了17.4℃.采用该方法制备的改性蒙脱土既可以进一步提高蒙脱土的层间距,又可以封闭TPP于MMT的片层间,阻止TPP挥发;同时克服季铵盐改性蒙脱土的热稳定性低的问题,得到了层间距大、热稳定性高的有机化蒙脱土,为有机化蒙脱土在高熔点聚合物改性方面提供了条件.     

三聚苯撑乙烯/蒙脱土发光光谱的时间依赖性

用原位插层法制备了插层型的三聚苯撑乙烯/蒙脱土(TPV/MMT)纳米复合材料. 研究了新制备及在室温储存180天后的TPV/MMT纳米复合材料的荧光光谱及蒙脱土层间距的变化情况. 荧光光谱分析表明, 储存180天后, TPV/MMT纳米复合材料的最大发射峰由494 nm蓝移到438 nm, 半峰宽由77 nm增加到104 nm. X射线衍射结果表明, 与新制备的复合材料相比, 蒙脱土的层间距由1.52 nm减小到1.22 nm. 红外光谱分析表明, 室温储存180天后的三聚苯撑乙烯苯环的某些特征峰由1598 和1554 cm-1分别红移到1506和1462 cm-1. 依据相关实验和理论数据探讨了储存180 天前后TPV在蒙脱土中聚集态结构的变化方式.     

PU/MOMMT纳米复合材料的制备与研究

纳米复合材料由于其纳米尺寸效应，表面效应以及纳米粒子与基体界面间强的相互作用，具有优于相同组分常规复合材料的力学、热学等性能，引起了人们的广泛关注。用纳米材料改性聚合物，制备纳米复合材料是获得高性能高分子复合材料的重要方法。1998年以来，Pinnavaia等首先制备了聚氨酯，蒙脱土（PU／MMT）纳米复合材料，研究了有机蒙脱土在聚醚中的分散性。其后Chen等将聚羟基己内酯/蒙脱土（PCL／MMT）纳米复合材料加入到PCL和二苯基甲烷-4，4＇-二异氰酸酯（MDI）合成的预聚体与1，4-丁二醇扩链反应后的溶液中，制备了PU／MMT纳米复合材料。少量PCL／MMT的引入可使复合材料的综合性能大幅提高。     

Temperature effects on surface activity and application in oxidation of toluene derivatives of CTAB-SDS with KMnO4

The γ_cmc values of CTAB-SDS decrease from 63.67 mN/m at 10‡C to 36.38 mN/m at 90‡C, slightly lower than those of either CTAB or SDS. Correspondingly, the CMC of CTAB-SDS decreases almost by half. The increase of surface activity of CTAB-SDS can be attributed to the relatively weak electrostatic interaction at high temperature, which is supported by the increase of solubility of CTAB-SDS with rise in temperature. Catalytic effect on oxidation of toluene derivatives with potassium permanganate follows the order CTAB-SDS > SDS > CTAB. This is not caused by the dissociative effect of CTAB-SDS with low surface activity at low temperature, as seen from the fact that almost all oxidative products can be retrieved for different toluene derivatives and surfactants by mimicking the conditions of reaction. In the emulsifications of toluene derivatives at 90‡C, the time that turbid water layers of surfactant solutions take to become clear is the same as that of the catalytic effect on oxidation of toluene derivatives. Thus, it can be inferred that surfactants can improve the oxidation yields of toluene derivatives by increasing the contact between two reacting phases.     

Effect of cetyltrimethylammonium bromide addition on the emulsions stabilized by montmorillonite

The wettability of montmorillonite could be in situ modified by cationic surfactant cetyltrimethylammonium bromide (CTAB). The type and stability of emulsions prepared from montmorillonite with different concentrations of cationic surfactant were investigated, and a double phase inversion of emulsions was observed. The adsorption of CTAB on montmorillonite particles was studied by surface tension and zeta potential measurements, and the variation of the wettability of particles with the concentration of CTAB was characterized by the contact angle measurements. The adsorption of particles at the surface of emulsion droplets was observed by laser-induced confocal scanning microscopy. At low surfactant concentrations, the adsorption of CTAB on montmorillonite increased the hydrophobicity of the particles, and the stability of oil-in-water emulsions was enhanced. With the increase of the CTAB concentration, montmorillonite particles changed from hydrophilic to hydrophobic, and water-in-oil emulsions were obtained. However, at higher surfactant concentrations, the emulsions inverts to O/W again because montmorillonite particles were reconverted into hydrophilic due to the formation of CTAB bilayer on the surface of montmorillonite.     

Structure Characterization and Thermal Properties of PMMA／Montmorillonite Nanocomposites via Emulsion Polymerization

Montmorillonite(MMT) modified with sodium silicate can change the arrangement of its layers fromedge-face and edge-edge to face-face. With the fine dispersion of the modified MMT in water, the cation-ex-change reaction was carried out with cetyltrimethyl ammonium bromide (CTAB) to obtain organo-montmoril-lonite (OMMT). As OMMT was uniformly dispersed in methyl methacrylate (MMA) monomer, PMMA/OMMT nanocomposites were formed via a common emulsion polymerization. The products were extractedwith hot acetone and characterized by FTIR, molecular weight, X-ray diffraction(XRD), transmission elec-tron microscopy(TEM), DSC and TGA. These results show that most of the OMMT layers have been exfo-liated, while the thermal stability is increased obviously. By means of FTIR spectral analysis, the ratios ofthe macromolecular radicals‘ termination of disproportionation patterns to combination are increased with theaddition of OMMT. This result further confirms the increase of the thermal degradation temperatures andglass transition temperatures of the PMMA/OMMT nanocomposites.     

Synthesis and characterization of organomodified Na-MMT using cation and anion surfactants

The Sodium Montmorillonite (Na-MMT) is not susceptible to polymer due to its organophilic character and low basal spacing. The primary objective of this study was to improve Na-MMT platelets separation by organically modifying it with cation and anion exchanges using Cetyl trimethyl ammonium bromide (CTAB) and Sodium dodecyl sulfate (SDS) respectively. Basal spacing, presence of functional groups, Zetapotential with particle size analysis and thermal stability of the Organomodified Na-MMT (OMMT) were characterized using XRD, FTIR, zeta-potential analyzer and TGA respectively. The basal spacing of CTAB modified OMMTincreased to 19.5 ? from 11.0 ? which corresponds to the basal spacing of Na-MMT. The SDS modified OMMT did not show any increase in the basal spacing. FTIR spectra of CTAB modified Na-MMT illustrated the attachment of CTAB functional groups to Na-MMT, while the same was absent in the case of SDS modified Na-MMT. The zeta-potential of Na-MMT shifted from −24.88 mV to 15.66 mV in the case of CTAB modified Na-MMT and 12.49 mV for SDS modified Na-MMT, indicating a greater surface potential of the modified nanoclay. The TGA showed greater weight loss for CTAB modified Na-MMT than that for Na-MMT, indicating the effective Na⁺ ion exchange with alkyl amines.     

高抗冲聚苯乙烯/蒙脱土复合材料的阻燃性研究

用经十六烷基三甲基溴化铵有机化改性的蒙脱土 (OMMT)与高抗冲聚苯乙烯 (HIPS)通过熔融插层法制备了HIPS OMMT复合材料 ,用X ray衍射技术对材料结构进行了表征 ,发现钠基蒙脱土 (Na+ MMT)和有机蒙脱土的层间距分别为 1 5 1nm和 2 18nm ,HIPS OMMT(5phr)复合材料中蒙脱土的层间距因聚合物大分子的插入扩大为 3 4 4nm ;而HIPS与Na+ MMT形成的复合材料的层间距与Na+ MMT的层间距相比却没有变化 ,表明未有机化处理土没有形成插层结构 .锥形量热仪的研究结果表明HIPS OMMT复合材料的热释放速率、质量损失速率以及生烟速率等燃烧特性参数均显著降低 ,具有较明显的阻燃性和抑烟性 ,而HIPS Na+ MMT非插层型复合材料只有在Na+ MMT很高填充量下 (>2 0phr)才有一定阻燃效果 .比较了铵盐对HIPS阻燃性的影响 ,结果表明铵盐自身的阻燃作用很小 ,主要是插层复合结构起阻燃作用 .     

聚氨酯/蒙脱土纳米复合材料的制备与性能研究

纳米复合材料由于其纳米尺寸效应 ,表面效应以及纳米粒子与基体界面间强的相互作用 ,具有优于相同组分常规复合材料的力学 ,热学等性能 ,引起了人们的广泛关注 .用纳米材料改性聚合物 ,制备纳米复合材料是获得高性能高分子复合材料的重要方法 ,采用较多的是插层复合法 ,可分为两类 ,一是单体预先插层于层状结构填料的晶片层间 ,然后聚合 ;二是聚合物溶液或熔体直接插层于层状结构填料的晶片层间 .聚氨酯 (PU)是由多异氰酸酯与多元醇通过加聚反应而形成的高聚物 ,其重复结构单元是氨基甲酸酯链段( R2 OCONHR1NHCOO) .PU弹性体具有耐磨…     

Characterization of surfactant and phospholipid vesicles for use as pseudostationary phases in electrokinetic chromatography

The physical, electrophoretic and chromatographic properties (mean diameter, electroosmotic flow, electrophoretic mobility, elution range, efficiency, retention, and hydrophobic, shape, and chemical selectivity) of three surfactant vesicles and one phospholipid vesicle were investigated and compared to a conventional micellar pseudostationary phase comprised of sodium dodecyl sulfate (SDS). Chemical selectivity (solute-pseudostationary phase interactions) was discussed from the perspective of linear solvation energy relationship (LSER) analysis. Two of the surfactant vesicles were formulated from nonstoichiometric aqueous mixtures of oppositely charged, single-tailed surfactants, either cetyltrimethylammonium bromide (CTAB) and sodium octyl sulfate (SOS) in a 3:7 mole ratio or octyltrimethylammonium bromide (OTAB) and SDS in a 7:3 mole ratio. The remaining surfactant vesicle was comprised solely of bis(2-ethylhexyl)sodium sulfosuccinate (AOT) in 10% v/v methanol, and the phospholipid vesicle consisted of 1-palmitoyl-2-oleyl-sn-glycero-3-phosphocholine (POPC) and phosphatidyl serine (PS) in 8:2 mole ratio. The mean diameters of the vesicles were 76.3 nm (AOT), 86.9 nm (CTAB/SOS), 90.1 nm (OTAB/SDS), and 108 nm (POPC/PS). Whereas the coefficient of electroosmotic flow (10(-4) cm2 V(-1) s(-1)) varied considerably (1.72 (OTAB/SDS), 3.77 (CTAB/SOS), 4.05 (AOT), 5.26 (POPC/PS), 5.31 (SDS)), the electrophoretic mobility was fairly consistent (-3.33 to -3.87 x 10(-4) cm2 V(-1) s(-1)), except for the OTAB/SDS vesicles (-1.68). This resulted in elution ranges that were slightly to significantly larger than that observed for SDS (3.12): 3.85 (POPC/PS), 8.6 (CTAB/SOS), 10.1 (AOT), 15.2 (OTAB/SDS). Significant differences were also noted in the efficiency (using propiophenone) and hydrophobic selectivity; the plate counts were lower with the OTAB/SDS and POPC/PS vesicles than the other pseudostationary phases (< or = 75,000/m vs. > 105,000/m), and the methylene selectivity was considerably higher with the CTAB/SOS and OTAB/SDS vesicles compared to the others (ca. 3.10 vs. < or = 2.6). In terms of shape selectivity, only the CTAB/SOS vesicles were able to separate all three positional isomers of nitrotoluene with near-baseline resolution. Finally, through LSER analysis, it was determined that the cohesiveness and hydrogen bond acidity of these pseudostationary phases have the greatest effect on solute retention and selectivity.     

β-羟基丁酸与β-羟基戊酸共聚物 (PHBV)/蒙脱土纳米复合材料的结构与性能

用溶液复合法成功地制备了插层型PHBV／蒙脱土纳米复合材料。采用X射线衍射（XRD）和透射电子显微镜（TEM）研究了复合材料的结构，硅酸盐片层间距从1.8nm升至2.4nm左右。同时研究了复合材料的结晶，熔融，动态力学行为和力学性能，发现有机蒙脱土的加入，可以加快PHBV的结晶,降低熔融温度，使基体的玻璃化转变温度升高，提高了材料的力学性能，有机蒙脱土含量在3％时，其综合性能最佳。     

Surfactant-assisted synthesis,characterizations, and room temperature ammonia sensing mechanism of nanocrystalline CuO

CuO nanocrystalline powder has been synthesized by a sol?gel auto combustion route with cetyltrimethylammonium bromide (CTAB) as cationic surfactant, and sodium dodecyl sulphate (SDS) as anionic surfactant. The powder samples are characterized by TGA/DTA, XRD, FESEM, and TEM techniques. Thermal analysis of the dried gel samples shows that addition of surfactant in the precursor increases the heat of reaction, which is evolved in the decomposition of metal citrate complex. The CTAB and SDS addition in the reaction mixture lowers the average crystallite size to few tens of nanometer. Surfactant doping in precursor causes a variation in lattice strain and changes to its type to compressive. CuO nanoparticles are bound together into facets–like weakly aggregated clusters, as indicated by FESEM images. TEM micrographs indicate the porous, nearly spherical particles having crystallite size around 7 and 18 nm for CTAB and SDS surfactant assisted CuO samples respectively. CuO nanoparticles assembled as thick film have been tested for their response to 100 ppm ammonia gas at room temperature. Cationic surfactant assisted sample shows maximum response to ammonia as compared to anionic surfactant. The CTAB assisted sensor shows almost completes recovery in 500 s whereas SDS assisted sample shows 75% recovery in the same time. The ammonia response of the films obeys the Elovich equation. The response rate of sensor is found to be maximum for CTAB assisted CuO films as compared to other samples. The kinetics of the response reaction shows that the ionic surfactants assisted CuO follows second order reaction kinetics.