Acoustic dispersion and attenuation measurement using both transmitted and reflected pulses

Traditional broadband transmission method for measuring acoustic dispersion and attenuation requires the measurement of the thickness of the specimen, the transmission coefficient at the water–specimen interface, and the Fourier spectra of two transmitted pulses. A new method has recently been developed that can determine both the thickness and dispersion of the specimen by utilizing the phase spectra of two additional pulses reflected back from the front and back surfaces of the specimen. In this paper, the method is further extended to the measurement of attenuation. If the density of the specimen is known, the frequency-dependent transmission coefficient can be determined based on the measured phase velocity, and only the amplitude spectra of the two transmitted pulses are used to determine the attenuation. If the density of the specimen is unknown, the attenuation can be determined from the amplitude spectra of all the four pulses. In both cases, the thickness estimated from the phase spectra of the four pulses is utilized. Experimental results from two specimens are presented to demonstrate the application of the new method.     

A novel method for the measurement of acoustic speed

Traditional methods for measuring acoustic speed require knowledge of either the specimen thickness or the distances between the transducers and the specimen. In general, the accuracy in measuring these quantities determines the accuracy of the experimental technique for measuring speed. This problem is particularly acute in measuring sound speed in biological specimens. A new method for measuring acoustic speed of materials, which eliminates the need for determining these quantities, has been developed. The technique, which necessitates the use of only one transducer, requires measurement of four times of flight of a sound pulse and the knowledge of the speed of sound in a reference fluid medium in which the specimen is placed. Ultrasonic speed in stainless steel and Plexiglas was measured using this method to verify its validity. Results on measurements on porcine liver, myocardium, and soft fat are also reported.     

Simultaneous measurement of sound velocity and wall thickness of a tube.

A method for simultaneously measuring the sound propagation velocity and the thickness of each wall on the opposite sides of a tube is presented. The method uses a pair of ultrasound transducers to produce two reflected pulses from the outer and inner surfaces of the tube wall on the each side, and two transmitted pulses, one with and one without the tube sample between the two transducers. Using the time-domain analysis, sound velocity and wall thickness of the tube are determined from the time delays between the three pairs of ultrasound pulses, whereas using the frequency-domain analysis, phase velocity, group velocity, and wall thickness of the tube are determined from the phase differences between the three pairs of ultrasound pulses. Results of measurements on five tube samples are reported.     

Classroom measurements of sound speed in fresh/saline water

A tabletop apparatus permitting demonstrations and hands-on student exercises in the measurement of sound speed in water as a function of both temperature and salinity, at atmospheric pressure, is described. By measuring sound speed using a differential technique with a precisely measured path length difference Δx, errors due to uncertainty in original path length are minimized. The apparatus can be used to measure sound speed in freshwater baths of varying temperature and room temperature baths of varying salinities to provide the student a clear picture of sound speed variation along two axes.     

深海近距离声场频率-距离干涉结构反演海底声学参数

地声反演一般存在多解性的问题,不易有效分离沉积层声速与厚度,本文提出了一种当声源与接收水听器分别位于海面与海底附近时匹配声场干涉周期反演深海沉积层声速与厚度的方法。该声场周期结构由直达波与海底沉积层反射回波干涉形成,其干涉周期受沉积层声速和厚度影响,通过匹配实测与理论计算的声场干涉周期可有效反演沉积层声速和厚度。开展了深海实验验证,利用水听器接收到的近距离船舶噪声的声场干涉条纹,反演得到的实验海域海底沉积层声速与该海域海底表层采样平均值差小于20 m/s。数值仿真与实验结果表明该方法可以有效反演沉积层的声速与厚度。      

Refractive index measurement by spectrally resolved interferometry using a femtosecond pulse laser

We describe a measurement method of refractive indices by way of spectrally resolved interferometry using a femtosecond pulse laser. The method is dispersion insensitive and requires no prior precise knowledge of the geometrical thickness of the specimen. Not only the group but also the phase refractive index can be determined over the wide spectral range covered by the optical comb of the femtosecond pulse laser in use.     

Non-contact acoustic method for the simultaneous measurement of thickness and acoustic properties of biological tissues

The frequency dependence of the magnitude and phase shift of reflected waves from a thin tissue specimen has been found to yield characteristics patterns as a function of the specimen thickness. By analysis of those characteristic patterns, the specimen thickness can be determined so that the attenuation constant and the sound speed can be obtained by a non-contact procedure. The method is demonstrated in the frequency range 100 MHz to 200 MHz, using a scanning acoustic microscope and approximately 10 μm thick myocardial tissue samples of human origin, one paraffin embedded.     

相移干涉法测量ICF微球内表面粗糙度

 通过分析光线通过微球壳层后各界面的相位分布,讨论了相移干涉法测量微球内表面粗糙度的基本原理,研究了微球上部壳层对内表面粗糙度测量的影响,得到了聚苯乙烯,聚a甲基苯乙烯微球的内表面形貌特征图像,测量数据与原子力显微镜测量数据在同一量级。以微球壳层对超光滑碳化硅及单晶硅片表面形貌的调制作用为研究对象,讨论了微球的外表面粗糙度以及微球壁厚对内表面粗糙度测量结果的影响,确定了相移干涉法测量微球内表面粗糙度的不确定度,实验结果表明：对于表面粗糙度小于30 nm、厚度小于9 mm的微球,测量不确定度小于0.4 nm。     

Pulse-echo measurement of longitudinal sound velocity in nanometer thin films

We propose a method to measure the longitudinal sound velocity in thin films of a few nanometer thickness using laser-based picosecond ultrasonics. In periodic multilayer structures, picosecond pulse-echo techniques were used to measure the effective sound velocity, which is related to the velocities of individual constituents through the superlattice phonon dispersion relation. The individual sound velocities can then be extracted, provided two or more effective velocities are obtained from multilayers of different thickness ratios. Longitudinal sound velocities in ion-beam sputtered Mo and amorphous Si films of 2 to 5 nm thickness have been determined to be 98 and 94% of the bulk speed, respectively. We believe this technique has general applicability to sound velocity measurement in ultra-thin films. PACS 68.60.Bs; 68.65.Ac; 78.47.+p     

Extremely simple device for measuring 20-fs pulses

We demonstrate an extremely simple frequency-resolved optical-gating device (GRENOUILLE) capable of measuring pulses with spectra wider than 100 nm. Its nearly all-reflective geometry minimizes the material dispersion, allowing accurate measurement of pulses as short as 19 fs.     

用脉冲光声法测量固体介质中声速

提出了一种利用脉冲光声技术测量固体介质中声速的方法,建立了由YAG激光器和超声探测器组成的实验系统,脉冲激光在固体表面产生脉冲超声波,通过测量脉冲声波在固体内多次反射后的出射信号及固体的厚度,即可算出固体介质中的声速.对黄铜及铝的测量结果表明,这是一种准确性较高的固体介质中声速测量方法.该测量方法可作为综合设计性物理实...     

水下翼型结构流噪声实验研究

为测量流激水下翼型结构的流噪声,提出了一种混响箱测量方法。在重力式水洞中搭建了一套实验测量系统,利用混响箱法测量了水下翼型结构模型的辐射声功率。在此基础上研究了流速及结构参数(厚度、肋、声学覆盖层)对其辐射声功率的影响。结果表明:当流速小于5 m/s时,辐射声功率随流速的6次方增长,符合偶极子的辐射规律;当流速大于5 m/s时,辐射声功率随流速的10土1次方规律增长,不再按偶极子的规律辐射;若对水下翼型结构模型加厚、加环肋及外部敷设黏弹性材料,均可在一定程度上抑制流噪声。此研究方法可对水下复杂结构的辐射声功率测量及结构优化设计提供一定的参考。      

高速光脉冲的测量方法

 综述了目前国际上公认的测量高速光脉冲的几种方法，主要包括电光条纹相机（SC）、快速脉冲取样、二次谐波产生（SHG）、频率分辨光学门（FROG）以及光谱相位干涉直接电场重建（SPIDER）等。详细地阐述和分析了这些方法的原理、特点、适用范围以及它们的研究现状。     

Uncertainty of array-based measurement of radiated and absorbed sound intensity

Patch near-field acoustic holography (NAH) coupled with an array of sound intensity probes allows separating the sound field incident on a surface from the one radiated by the surface itself. Although the measurement principle has been successfully used to separate the noise source contribution from disturbing sources and/or noise reflections, the method accuracy has not been investigated in the literature. We describe the results of experiments meant to evaluate the uncertainty in the identification of noise radiated by vibrating panels with different absorption characteristics in presence of an incident acoustic radiation using the statistically optimized near-field acoustic holography. Measurement errors were evaluated through tests performed in controlled acoustic conditions. Results evidenced that the measurement uncertainty depends on the accuracy of the microphone array positioning and on the incident sound field. These conclusions were in agreement with the results obtained by simulations in the phase of instrument optimization.     

利用自发布里渊散射测量液体声速

为了克服共振干涉法在液体的热力学声速和高频声速测量方面精度不高的问题, 本文建立了一种基于自发布里渊散射原理的测定液体声速的实验装置. 利用法布里-珀罗干涉仪对散射光进行扫描滤波, 数据采集卡结合光子计数器对散射光进行探测, 设计了一种散射光信息采集分析方法. 该实验方法有效的解决了传统布里渊散射方法中信号失真的问题, 显著地提升了液体声速测量精度. 对308.6–906.2 MHz内298.15 K饱和液相CCl₄声速进行了测量, 测量结果与文献值具有较好一致性. 利用法布里-珀罗干涉仪周期性扫描的滤波原理, 通过在测量得到的布里渊频移上加减整数倍个自由波谱区, 得到了更大频率的波谱信息, 进而设计一种测定介质高频声速的方法. 对CCl₄在5406.1–5521.0 MHz频段内的声速进行了测量. 实验结果显示, CCl₄的热力学声速随频率无明显变化, 而高频声速随频率的增大呈增大趋势且远大于热力学声速, 证实CCl₄具有色散现象.     

Ultrashort pulse characterization with a terahertz streak camera

A phase-locked terahertz transient is exploited as an ultrafast phase gate for femtosecond optical pulses. We directly map out the group delay dispersion of a low-power near-infrared pulse by measuring the electro-optically induced polarization rotation as a function of wavelength. Our experiment covers the spectral window from 1.0 to 1.4 μm and reaches a temporal precision better than 1 fs. A quantitative analysis of the detector response confirms that this streaking technique requires no reconstruction algorithm and is also well suited for the characterization of pulses spanning more than one optical octave.     

基于锁定放大器的声速测量法

介绍一种用锁定放大器替代示波器确定声波相位,进行声速测量的方法.利用锁定放大器的高灵敏度、高信噪比的特点,能有效地提高实验装置的抗干扰性和测量准确度,被测量对象也可由原单一频率的超声波改变为任意频率的声波.本实验不确定度<5%,若采用更精密的仪器,实验不确定度很容易达到0 5%.     

On the metrology of the speed of sound in liquids

Decentralization of the standards base in measuring the speed of sound in liquids by expressing the speed of sound in fractions of the speed of light in vacuum is considered. A method to take into account the diffraction effects by measuring the speed of sound in the case of a constant acoustic wavelength and binding the absolute speed of sound values to the calculated thermodynamic values obtained by the nonacoustical method when the adiabatic compressibility is equal to the isothermal one is proposed. Errors of the reproducibility of the unit of the speed of sound in water using the proposed method are estimated.     

Application of acoustic methods for a non-destructive evaluation of the elastic properties of several typologies of materials

In solid phase materials, differently from what happens in the fluid phase, elastic waves propagate both through longitudinal and transverse waves. From the speed of propagation of longitudinal and transverse waves, it is possible to evaluate important elastic properties of the solids under study, namely the Young’s modulus, the Poisson’s coefficient, the bulk modulus and the shear modulus. This work suggests an accurate method for measuring wave propagation speeds in homogeneous and non-homogeneous materials with the purpose to evaluate their mechanical properties and the associated uncertainty.First of all, to assess the performance of the proposed methodology, based on the “pulse-echo” technique, in terms of accuracy and precision, measurements of wave propagation speeds have been carried out, in atmospheric conditions, in well-known homogeneous and isotropic materials, such as copper, aluminum, stainless steel and also polymethyl methacrylate (Plexiglas®), Teflon® and optical glass BK7. These results were compared with the values reported in literature (if present), showing how published speed of sound data are very disperse and not so reliable owing to the lack of a precise uncertainty evaluation and of the temperature value associated to the measurement. Then, the same experimental apparatus was used for measuring speed of sound as a function of temperature (from 274.15 to 313.15 K) for 304 stainless steel and oxygen free copper, showing a good accuracy of the results also for temperature conditions far from ambient. Finally, the same procedure was applied to a non-homogeneous solid, obtaining some very preliminary results in typical mediterranean building material, as Carrara marble.     

A Novel Rotation Speed Measurement Method Based on Surface Acoustic Wave

This paper presents an original passive wireless rotation speed measurement method based on surface acoustic wave (SAW) technology. A theoretical analysis was conducted on the principle of SAW rotation speed measurement and a numerical analysis on the SAW response energy pulses with different rotation angles and resonance frequencies was performed. Numerical calculation results showed that when the distance and the effective length of the antenna connected to SAWR vary with the rotation angle, the energy of acquired SAW response varies periodically. The rotation speed was estimated by searching the crossing points of the SAW response energy pulses and its mean value line. The SAW rotation speed measurement system was set up and the high performance SAW resonators were fabricated on a quartz substrate. The proposed measurement system was tested with a maximum error of 0.6 rpm, indicating that the system is capable of measuring rotation speeds from 10 to 100 rpm. Experimental results verified the validity and feasibility of presented rotation speed measurement method.