Comparative study for the analysis of parabens by micellar electrokinetic capillary chromatography with and without large-volume sample stacking technique

The separation and determination of four parabens (methyl, ethyl, propyl, and butyl p-hydroxybenzoate) which are commonly used as preservatives in cosmetic products, by micellar electrokinetic capillary chromatography (MEKC) with and without large-volume sample stacking (LVSS) technique were compared. As an effective on-line concentration technique, LVSS was successfully combined with MEKC to determine neutral parabens in an acidic media. The effects of some typical parameters such as sample volume, buffer pH, temperature, and concentration of surfactant were examined. The detection limits for this LVSS-MEKC method were found to be 3.0 × 10⁻⁷ M for each of the parabens based on the signal-to-noise ratio of 3, which were around 300 times lower than normal MEKC technique. The curves of peak response versus concentration were linear from 1.0 × 10⁻⁶ to 5.0 × 10⁻⁵ M with regression coefficients of 0.9987, 0.9960, 0.9925 and 0.9864, respectively. A simple and easy-manipulative sample preparation method was developed and validated by analyzing commercially available cosmetic samples. It was found that with current sample preparation process and instrumentation system, 0.5 g of sample is enough for the analysis of parabens preservatives in cosmetic product with satisfactory results.     

Immobilized capillary adenosine deaminase microreactor for inhibitor screening in natural extracts by capillary electrophoresis

A novel strategy for the preparation of in-column adenosine deaminase (ADA) microreactor and rapid screening of enzyme inhibitors in natural extracts was demonstrated. In this approach, ADA was encapsulated in anionic polyelectrolyte alginate that was immobilized on the surface of fused-silica capillary via ionic binding technique with cationic polyelectrolyte polyethylenimine (PEI). On-line enzyme inhibition study was performed by capillary electrophoresis (CE). The substrate and product were baselined separated within 75 s. The enzyme activity was determined by the quantification of peak area of the product. Enzyme inhibition can be read out directly from the reduced peak area of the product in comparison with a reference electropherogram obtained in the absence of any inhibitor. The inhibition percentage was used to evaluate relative activity of ADA microreactor. A known ADA inhibitor, erythro-9-(2-hydroxy-3-nonyl) adenine (EHNA) was employed as a model compound for the validation of the inhibitor screening method, and the screening of ADA inhibitor in 19 traditional Chinese herbal medicines was performed.     

Large‐volume sample stacking with polarity switching for monitoring of nucleotide pyrophosphatase/phosphodiesterase 1 (NPP1) reactions by capillary electrophoresis

Nucleotide pyrophosphatase/phosphodiesterase 1 (NPP1) is a membrane glycoprotein involved in the hydrolysis of extracellular nucleotides. Its main substrate is ATP yielding AMP and pyrophosphate. NPP1 has been proposed as a novel drug target, for diabetes type 2 and the treatment of calcium pyrophosphate dihydrate deposition disease leading to inflammatory arthritis. The monitoring of NPP1 reactions is difficult because its velocity is very slow requiring highly sensitive analytical procedures. In this study, a method of large‐volume sample stacking with polarity switching was developed, and separations were optimized. Large sample volumes were loaded by hydrodynamic injection (5 psi, 13 s) followed by removal of a large plug of sample matrix from the capillary using polarity switching (?10 kV). The stacked analytes were subsequently separated in phosphate buffer (100 mM, pH 9.2) at 20 kV. The validated method was found to be linear (R² = 0.9927) in the concentration range of 0.05–50 μM of AMP, with high accuracy and precision. The determined LOD and LOQ of AMP were 18 nM and 60 nM, respectively. Compared to a previously reported CE procedure using sweeping technique, a fivefold improvement of sensitivity was achieved. Moreover, the new technique was faster, and reproducibility of migration times was improved (RSD value = 1.2%). Importantly, adenine nucleotide analogs and derivatives tested as NPP1 inhibitors could be completely separated from the substrate ATP and the enzymatic product AMP. The method was applied to NPP1 inhibition assays investigating nucleotide‐derived inhibitors in the presence of ATP.     

Determination of mercaptopurine and its four metabolites by large-volume sample stacking with polarity switching in capillary electrophoresis

This study describes approaches for stacking a large volume of sample solutions containing a mixture of mercaptopurine monohydrate, 6-methylmercaptopurine, thioguanine, thioguanosine, and thioxanthine in capillary electrophoresis (CE). After filling the run buffer (60 mM borate buffer, pH 8.5), a large sample volume was loaded by hydrodynamic injection (2.5 psi, 99.9 s), followed by the removal of the large plug of sample matrix from the capillary using polarity switching (-15 kV). Monitoring the current and reversing the polarity when 95% of current recovered, the separation of anionic analytes was performed in a run buffer < 20 kV. Around 44- to 90-fold improvement of sensitivity for five analytes was achieved by large-volume stacking with polarity switching when compared with CE without stacking. This method was feasible for determination of the analytes spiked in plasma. Removing most of electrolytes from plasma is a key step for performing large-volume sample stacking. Solid-phase extraction was used for pretreatment of biological samples. To our knowledge, this study is one of few applications showing the possibilities of this stacking procedure to analyze biological samples by large-volume sample stacking with polarity switching (LVSSPS) in CE.     

Combination of solid-phase extraction and large-volume stacking with polarity switching in micellar electrokinetic capillary chromatography for the determination of traces of nonsteroidal anti-inflammatory drugs in saliva

A reliable MEKC method for the identification and quantitation of traces of the nonsteroidal anti-inflammatory drugs (NSAIDs) ketoprofen, fenbufen and indomethacin in saliva is proposed. Using CE to analyze biological samples often requires suppressing the interferences and peak broadening typically resulting from high-conductivity sample matrices. We addressed this problem by using Microcon, a centrifugal filter device, to reduce the viscosity of saliva and exclude most higher-molecular-mass substances. This initial pretreatment was followed by the combined used of off-line SPE to isolate and concentrate the analytes, and large-volume stacking with polarity switching (LVSS) in the capillary. These two preconcentration steps allow the determination of NSAIDs at concentrations above 0.1 microg/L; therefore, the proposed SPE/LVSS/MEKC method affords a 500-fold sensitivity enhancement relative to conventional CE injection. The LODs obtained afford the determination of NSAIDs in saliva, where analytes can be present at the microgram-per-liter level.     

Combination of off-line solid-phase extraction and on-column sample stacking for sensitive determination of parabens and p-hydroxybenzoic acid in waters by non-aqueous capillary electrophoresis

For the first time, a procedure based on solid-phase extraction (SPE) for the simultaneous extraction of a group of parabens (methyl, ethyl, propyl, butyl and benzyl p-hydroxybenzoates) and p-hydroxybenzoic acid (PHBA), from environmental water samples has been developed. Analysis of the extracts was performed by non-aqueous capillary electrophoresis (NACE) coupled with diode array detection (DAD), using large-volume sample stacking (LVSS) based on the electroosmotic flow pump as on-column preconcentration technique. Several water samples, such as tap, river, and wastewater samples, were analyzed using both SPE-NACE-DAD and SPE-LVSS-NACE-DAD methods. It has been observed that in addition to SPE parameters such as sorbent material, sample pH, breakthrough volume, addition of an organic solvent and elution solvent, also sample characteristics, such as organic matter content, have influence on SPE extraction yields, especially in the case of PHBA. The presence of PHBA and some parabens was detected at trace levels in surface water samples. Concentrations up to 8.4 ng mL⁻¹ were found in raw wastewater, with the highest levels corresponding to methylparaben, propylparaben, and their main degradation product, PHBA.     

Oxidized multi-walled carbon nanotubes for the dispersive solid-phase extraction of quinolone antibiotics from water samples using capillary electrophoresis and large volume sample stacking with polarity switching

In this work, a new method for the determination of eleven quinolone antibiotics (moxifloxacin, lomefloxacin, danofloxacin, ciprofloxacin, levofloxacin, marbofloxacin, enrofloxacin, difloxacin, pefloxacin, oxolinic acid and flumequine) in different water samples using dispersive solid-phase extraction (dSPE) and capillary zone electrophoresis with diode-array detection was developed. Oxidized multi-walled carbon nanotubes (o-MWCNTs) were used for the first time as stationary phases for the off-line preconcentration by dSPE of the antibiotics. A 65 mM phosphate buffer at pH 8.5 was found adequate for analyte separation while large volume sample stacking with polarity switching of the analytes dissolved in water containing 10% (v/v) of acetonitrile was carried out in order to improve the sensitivity. dSPE parameters, such as sample volume and pH, o-MWCNT amount, volume and type of eluent in dSPE were optimized. Application of the developed method to the analysis of spiked Milli-Q, mineral, tap, and wastewater samples resulted in good recoveries values ranging from 62.3 to 116% with relative standard deviation values lower than 7.7% in all cases. Limits of detection were in the range of 28-94 ng/L. The proposed method is very fast, simple, repeatable, accurate and highly selective.     

Establishment and application of a new method for the determination of kinetic parameters by plug-plug kinetic capillary electrophoresis (ppKCE)

A novel plug-plug kinetic capillary electrophoresis method was established, which can be used to si-multaneously determine the kinetic parameters kon and koff in interaction systems. The method is comparatively simple and some restrictions in conventional ppKCE methods can be effectively avoided. The requirements for resolution and detection sensitivity in this method are much lower than those of conventional ppKCE. The successful determination of the kinetic parameters and the binding constant Kb between citalopram and BSA showed availability of this method. The results were confirmed by us-ing the time ratio method. The application field of kinetic capillary electrophoresis can be expanded with this new method.     

Quality by design-guided development of a capillary electrophoresis method for the simultaneous chiral purity determination and impurity profiling of tamsulosin

Analytical Quality by Design principles using the design of experiments were applied for the development of a capillary electrophoresis method for the determination of enantiomeric purity and chemically related impurities of tamsulosin. From initial scouting experiments, a dual cyclodextrin (CD) system composed of sulfated β-CD and carboxymethyl-α-CD was selected as the chiral selector. A fractional factorial resolution V+ design was used for the identification of the critical process parameters, while a face-centered central composite design and Monte Carlo simulations were employed for final optimization and defining the design space of the method. The experimental conditions of the working point were: 30 mM sodium phosphate buffer, pH 3.0, containing 40 mg/mL sulfated β-CD and 7 mg/mL carboxymethyl-α-CD, capillary temperature 18°C, applied voltage -23 kV. Following the assessment of robustness by applying a Plackett-Burman design, the method was validated according to the International Council for Harmonization of Technical Requirements for Pharmaceuticals for Human Use guideline Q2(R1). The method allowed the quantification of the chiral impurity and three other related impurities at the 0.1 % level with acceptable accuracy and precision.