用四(4-三甲铵苯基)卟啉作显色剂导数分光光度法同时测定钴镉铅的研究

本文以四(4-三甲铵苯基)卟啉作显色剂,在阳离子表面活性剂CPB存在下的pH9.8缓冲溶液中,利用三阶导数分光光度法,对钴、镉、铅的同时测定进行了详细研究。本方法测定灵敏度较高,对合成样品进行测定,结果令人满意。     

三阶导数分光光度法同时测定铜,钴与镉

采用三阶导数光谱技术，以ｍｅｓｏ－四（４－三甲铵基苯基）卟啉作显色剂分光光度法同时测定了微量的铜、钴与镉。方法中以铅离子掩蔽过剩试剂的吸收峰，然后进行三级微分求导，可以使铜、钴、镉吸收峰完全分开，于４１５ｎｍ、４３４ｎｍ及４３８ｎｍ处同时测定３元素含量，由三阶导数光谱的吸光值可求算出配合物的三阶导数摩尔吸光系数分别为：１．１１×１０６、３．９５×１０５及６．４７×１０５Ｌ·ｍｏｌ－１·ｃｍ－１。     

石墨炉原子吸收测定高纯稀土氧化物中的镉和钴

本文用APDC作萃取剂,用MIBK作萃取溶剂,从pH≈4的稀土溶液中分离富集镉、钴,然后用石墨炉测定。镉的检出限是1.6×10~(-8)％,钴是7.5×10~(-8)％。用此法分析了高纯氧化钇、氧化钕、氧化镧,得到了满意的结果。由于APDC与稀土元素都不能形成稳定络合物,此法可视为测定不同稀土化合物中镉、钴的通用方法。 (一)仪器及试剂 1.仪器及测定条件:P-E2380原子吸收分光光度计;HGA-400型石墨炉;日立56型记录仪;镉、钴空心阳极灯(上海产)。镉灯电流8毫安;分析线2288埃;狭缝0.7毫微米干燥温度110℃,20秒;灰化温度350℃,20秒;原子化温度1700℃,5秒;正常加热;净化     

快速石墨炉原子吸收法测定金属钴和海水中微量镉

报道了用热解石墨涂层管快速无干扰直接测定金属钴中镉的方法,并提出以草酸为基体改进剂降低背景吸收直接测定海水中微量镉.     

导数—多波长线性回归吸光光度法同时测定锰钴锌

研究了以5-Br-PADAP为显色剂,导数-多波长线性回归吸光光度法同时测定锰、钴、锌。在pH 9.2的氯化铵-氨水和乳化剂OP介质中,锰、钴和锌与5-Br-PADAP发生较灵敏的显色反应。在波长560～574nm范围内每隔2nm进行导数-多波长线性回归,方法应用于大米、面粉和啤酒中的锰、钴、锌同时测定,获得了较好的结果。     

天然杂质对闪锌矿电子结构和半导体性质的影响

采用密度泛函理论系统研究了分别含有十四种天然杂质的闪锌矿的电子结构,并讨论了这十四种杂质对闪锌矿半导体性质的影响.研究结果表明,锰、铁、钴、镍、铜、镉、汞、银、铅、锑杂质的存在使闪锌矿的带隙变窄,导致吸收带边增大.除了镉和汞杂质外,其余杂质的存在均导致费米能级向高能级方向移动,并且在闪锌矿禁带中产生了杂质能级.铁、镓、锗、铟、锡、锑杂质使闪锌矿的半导体类型由p型变为n型;而锰、钴、镍、铜、镉、汞、银、铅杂质对闪锌矿的半导体类型没有影响.铜杂质使闪锌矿由直接带隙变为间接带隙半导体.     

双波长K系数—导数吸光光度法同时测定重油中钴和镍

提出了双波长K系数-导数吸光光度法,以样品中两组分的峰值波长互为测定波长和参比波长,以一套导数值数据进行两组分的同时测定,具有简便、灵敏度高的优点.以三正辛胺萃取分离干扰离子,OP—5-Br-PADAP显色体系同时测定了重油中的钴、镍.结果令人满意.     

导数分光光度法同时测定镍样中微量钴和铁

本文利用硫氰酸铵和丙酮的混合液作显色剂,利用-阶导数消除基体镍和多数离子的干扰,对金属镍中微量钴和铁进行同时测定,结果满意。     

示波极谱法连续测定含钴和锡矿石中铜、铅、镉、锌

矿石中锌、铜、铅、镉的极谱法测定,大都是在不同的底液中分别进行。在氢氧化铵-氯化铵底液中,锌、铜、镉虽有良好的极谱波,但钴与锌波重叠,严重干扰测定,大量锰亦有影响。在盐酸底液或氨基乙酸-氯化铵底液中,锌、铜、铅、镉虽可连续测定,但锡与     

纤维素非水溶剂的进展

一、纤维素非水溶剂研究的历史 自从1857年Schweizer发现铜氨溶液可以溶解纤维素以来,至今已有一个多世纪,其后,仍不断研究。到本世纪50年代,以联邦德国Jayme为代表,以乙二胺溶剂为基础,加上镉、镍、钴、锌等金属氧化物,构成了镉、镍、钴、锌的乙二胺溶剂体系,均可溶解纤维     

Colorimetric assay for parallel detection of Cd2+, Ni2+ and Co2+ using peptide-modified gold nanoparticles

A colorimetric assay has been developed for parallel detection of Cd(2+), Ni(2+) and Co(2+) utilizing peptide-modified gold nanoparticles (P-AuNPs) as a sensing element based on its unique surface plasmon resonance properties. The functional peptide ligand, CALNNDHHHHHH, was self-assembled on gold nanoparticles (AuNPs) to produce P-AuNPs probe. The P-AuNPs probe could be used to simultaneously detect and showed different responses to the three ions Cd(2+), Ni(2+) and Co(2+) in an aqueous solution based on the aggregation-induced color change of AuNPs. The method showed good selectivity for Cd(2+), Ni(2+) and Co(2+) over other metal ions, and detection limit as low as 0.05 μM Cd(2+), 0.3 μM Ni(2+) or 2 μM Co(2+). To simultaneously (or parallel) detect the three metal ions coexisting in a sample, EDTA and imidazole were applied to mask Co(2+) and Ni(2+) for detecting Cd(2+), glutathione and EDTA were applied to mask Cd(2+) and Co(2+) for detecting Ni(2+), and glutathione and imidazole were applied to mask Cd(2+) and Ni(2+) for detecting Co(2+). Finally, the simple and cost-effective probe could be successfully applied for simultaneously detecting Cd(2+), Ni(2+), and Co(2+) in river water. Because this novel P-AgNPs-based probe design offers many advantages, including simplicity of preparation and manipulation compared with other methods that employ specific strategies, the sensing system shows potential application in the developing region for monitoring water quality.     

Synthesis of bis(amino alcohol)oxalamides and their usage for the preconcentration of trace metals by cloud point extraction.

C(2)-Symmetric two bis(amino alcohol)oxalamides (diamidediols) were synthesized and fully characterized. A new method was developed and successfully applied for the simultaneous preconcentration of both trace and toxic metals in water, by using C(2)-symmetric compounds. Under the optimum experimental conditions (i.e. pH = 10.0 +/- 0.2, 2.75 x 10(-3) mol L(-1) N,N'-bis[(1R)-1-ethyl-2-hydroxyethyl]ethanediamide (DAD1), 1.75 x 10(-3) mol L(-1) N,N'-bis[(1S)-1-benzyl-2-hydroxyethyl]-ethanediamide (DAD2), 0.10% w/v octylphenoxy-polyethoxyethanol (Triton X-114)), calibration graphs were linear in the range of 2.5 - 25.0 ng mL(-1) for Cu and Cd, 5.0 - 25.0 ng mL(-1) for Co and Ni. The enrichment factors were 18, 23, 18 and 20 for Cd, Cu, Co and Ni in the case of DAD1, respectively; 20, 22, 17 and 20 for Cd, Cu, Co and Ni in the case of DAD2. The limits of detection for DAD1 were found to be 0.45, 0.50, 1.25 and 0.60 ng mL(-1) for Cd, Cu, Co and Ni, respectively, and for DAD2 were found to be 0.44, 0.25, 0.60 and 1.55 ng mL(-1) for Cd, Cu, Co and Ni, respectively. The developed method was applied to the determination of Cu, Cd, Co and Ni in water samples and certified reference materials with satisfactory results.     

Determination of Cd,Mo, Cr and Co in biological materials by RNAA

A method for the determination of trace amounts of Mo, Cd, Co and Cr in biological materials by neutron activation analysis with radiochemical separation is presented. The method is based on the ion-exchange scheme developed by SAMSAHL, where Co and Cr are trapped on BioRad Chelex-100 and Cd and Mo on BioRad AG2X8. The elements Mo, Cd and Co can be determined without systematic errors. For the element chromium the situation is less clear, partially due to lack of sufficient certified reference materials for Cr. The method has been used in the characterization of candidate reference materials. Detection limits in these materials range from 1.5 g/kg for Co to 10 g/kg for Cr. Actual levels as low as 8 g/kg for Cd and 7 g/kg for Co were measured.     

On-line Preconcentration and Determination of Trace Metals in Water Samples by Flow Injection Combined with Flame Atomic Absorption Spectrometry via Calix[4]arene Carboxylic Acid Packed Micro-column

An adsorbent calix[4]arene carboxylic acid was employed as the adsorption material for on-line flow injection( FI) micro-column preconcentration coupled with flame atomic absorption spectrometry(FAAS) determination of trace heavy metals(Cu, Pb, Co, Ni and Cd). Parameters such as the pH, loading time and flow rate of sample, and the concentration, volume and flow rate of eluent were optimized. The enrichment factors are 50.0, 56.5, 11.6, 12.1 and 19.1 for Cu, Pb, Co, Ni, and Cd, respectively, and a sample throughput of 20 h^-1 was obtained. The limits of detection for Cu, Pb, Co, Ni, and Cd were in a range of 1.56―3.91 μg/L, and the relative standard deviations(RSDs) were less than 2.76%(n=7). Furthermore, the proposed method was successfully applied to the determination of Cu, Pb, Co, Ni, and Cd in certified reference materials and various water samples.     

Dithlzone extraction and flame atomic absorption spectrometry for the determination of cadmium,zinc, lead,copper, nickel,cobalt and silver in sea water and biological tissues

The method previously described for the determination of Cd, Zn, Cu, Ni and Co in sediments has been adapted for the determination of these metals, and lead and silver in sea water and biological tissues. For sea water the only treatment preceding extraction is pH adjustment; biological tissues are digested in nitric and perchloric acids and the residue taken up in dilute hydrochloric acid prior to pH adjustment and extraction. The method is sufficiently sensitive to allow Cd, Zn, Cu and Ni to be determined in all sea waters, Co and Ag in coastal waters, but Pb only in polluted water.     

Chemically modified multiwalled carbon nanotubes as efficient and selective sorbent for separation and preconcentration of trace amount of Co(II), Cd(II), Pb(II), and Pd(II)

Multi-walled carbon nanotubes (MWCNTs) were chemically functionalized by glutaric dihydrazide (GDH) and characterized with FT-IR technique. This new sorbent was used for enrichment and preconcentration of Co(II), Cd(II), Pb(II), and Pd(II) ions. The adsorption was achieved quantitatively on MWCNTs at pH 4.0, and then the retained metal ions on the adsorbent were eluted with 1.5 mol L^?1 HNO₃. The effects of analytical parameters including pH of the solution, eluent type, sample volume, and matrix ions were investigated for optimization of the presented procedure. The adsorption capacity of the adsorbent at optimum conditions was found to be 33.6, 29.2, 22.1, and 36.0 mg g^?1 for Co(II), Cd(II), Pb(II), and Pd(II), respectively. The LOD values of the method were 0.16, 0.19, 0.17, and 0.12 ng mL^?1 (3Sb, n = 10) for Co(II), Cd(II), Pb(II), and Pd(II), respectively. The RSDs values of the method were 0.75, 0.85, 1.16, and 1.30 ng mL^?1 for Co(II), Cd(II), Pb(II), and Pd(II), respectively. The method was applied for the determination of analytes in soil, well water, and wastewater samples with satisfactory results.     

Non-linear spectral interferences in an inductively coupled plasma optimized for simultaneous multi-element analysis of plant and soil samples by atomic emission spectrometry

Summary The spectral interferences by Al, Ca, Fe, K, Mg and Na in the direct simultaneous determination of As, Cd, Co, Cu, Hg, Pb and Se in plant and soil samples by ICP-AES are investigated, and a non-linear relationship between the apparent analyte concentration for As, Cd, Co, Hg and Se is observed. A correction method for non-linear spectral interferences is discussed and non-linear spectral correction coefficients are calculated.     

Online Solid-Phase Extraction of Cd(II), Cu(II), and Co(II) Using Covalently Attached Bis(salicylaldimine) to Silica Gel for Determination in Food and Water by Flame Atomic Absorption Spectrometry

In this study, a novel sorbent material bearing a bis(aldimine) group was designed and successfully synthesized by covalently bonding a 2-[N,N′-bis(salicylaldimine)]aminoethyl amine ligand to the silica gel surface that was characterized by carbon, hydrogen, and nitrogen elemental analysis, thermogravimetric analysis, and the Fourier transform infrared spectroscopy technique. The sorbent was used for the online solid-phase extraction (SPE) of Cd(II), Cu(II), and Co(II) ions for their determination at trace concentration levels by flame atomic absorption spectrometry. The effective factors for the online SPE such as the pH and the flow rate of the sample solution, and type, volume, and flow rate of eluent were investigated. The concentration levels of Cd(II), Cu(II), and Co(II) were measured in certified reference materials including Virginia tobacco leaves (CTA-VTL-2) and water-trace elements (NWTM-15.2) to validate this method. The metal levels in environmental water were determined by this method, and the values were checked by spiking and recovery experiments and independent analysis by inductively coupled plasma-mass spectrometry. The adsorption capacities of the sorbent were found to be 41.2, 31.6, and 25.6?mg/g for Cd(II), Cu(II), and Co(II), respectively. This method was also successfully used for the determination of Cd(II), Cu(II), and Co(II) concentrations in rice and molasses.     

Flame atomic absorption spectrometric determination of Cd(II), Ni(II), Co(II) and Cu(II) in tea and water samples after simultaneous preconentration of dithizone loaded on naphthalene

A simultaneous preconcentration procedure for the determination of Cd(II), Ni(II), Co(II) and Cu(II) by atomic absorption spectrometry is described. The method is based on solid phase extraction of the metal ions on dithizone loaded on naphthalene in a mini-column, elution with nitric acid and determination by flame atomic absorption spectrometry. The sorption conditions including NaOH concentration, sample volume and the amount of dithizone were optimized in order to attain the highest sensitivity. The calibration graph was linear in the range of 0.5–75.0 ng ml^?1 for Cd(II), 1.0–150.0 ng ml^?1 for Ni(II), 1.0–150.0 ng ml^?1 for Co(II) and 1.0–125.0 ng ml^?1 for Cu(II) in the initial solution. The limit of detection based on 3S_b was 0.13, 0.32, 0.33 and 0.43 ng ml^?1 for Cd(II), Ni(II), Co(II) and Cu(II), respectively. The relative standard deviations (R.S.D) for ten replicate measurements of 20 ng ml^?1of Cd(II), 100 ng ml^?1 of Ni(II), Co(II) and 75 ng ml^?1 of Cu(II) were 3.46, 2.43, 2.45 and 3.26%, respectively. The method was applied to the determination of Cd(II), Ni(II), Co(II) and Cu(II) in black tea, tap and river water samples.     

电感耦合等离子体质谱法快速测定苦荞茶中铜、铅、镉、钴、镍

建立了用硝酸-高氯酸消解样品,电感耦合等离子体质谱法(ICP-MS)测定苦荞茶中铜、铅、镉、钴、镍的方法.方法具有灵敏度高、检出限低、精密度好、基体干扰少、准确可靠、快捷、简便的特点.各元素方法检出限(3SD,μg/L)分别为:铜0.009、铅0.023、镉0.015、钴0.022、镍0.035;方法精密度(RSD,n=12)分别为:铜2.5%～3.0%、铅2.1%～2.3%、镉3.0%～3.8%、钴2.5%～2.6%、镍1.5%～1.9%;各元素加标回收率分别为:铜95.0%～105.0%、铅95.0%～105.0%、镉98.0%～105.0%、钴95.0%～105.0%、镍95.0%～105.0%.在线用铑作为内标95.0%～105.0%.方法经国家一级标准物质验证,测定值与标准值吻合.应用于实际样品测定,结果满意.