Bi-2223/Ag超导带材的失超传播速度研究

文中对超导带材的失超产生机理进行了详细分析,建立了其失超传播的计算模型。在此基础上,对Bi-2223/Ag高温超导带材失超传播进行了实验研究,用四引线法测得不同条件下其失超传播的U-t曲线,由此计算出Bi-2223/Ag超导带材的失超传播速度为0.4cm/s～1.98cm/s。实验结果表明:带材的失超传播速度与载流大小有关,与触发失超的能量无关,带材载流越大,失超传播得越快。     

一维热传播模型下高温超导带的失超特性研究

对Bi-2223/Ag高温超导带材的失超传播特性进行了研究。测量了Bi-2223/Ag带材在有绝缘材料包裹和液氮浸泡环境下的电压变化曲线,同时利用一维热流方程模型,模拟出超导体失超传播过程中由超导态过渡到正常态的温度变化行为,同时还对传输电流和触发能量对失超传播速度的影响进行了实验研究。这些工作对高温超导磁体及电力系统的应用有着重要的参考价值。     

Bi2223带材的临界电流及交流损耗研究

测量了77K温度下不同基体材料和不同芯数带材的临界电流和交流损耗.分析了弯曲应变对它们的影响.结果表明单芯样品的不可逆应变小于0.15%,而多芯样品的不可逆应变在01%到03%之间,多芯导体的机械性能比单芯导体的好,增加芯数可以提高机械性能,金属包套材料对超导芯起到了增强的作用,它防止了超导芯中裂纹的进一步传播.自场损耗随外加应变的增加而增加,这种大幅度的增加与应变使带材的临界电流急剧减小直接相关 关键词： 高温超导体 临界电流 交流损耗     

Study of air heat treatment on Bi-2223/Ag superconducting tapes

Heat treatment has been carried out on commercially available Bi-2223/Ag superconducting tape under various temperature conditions in air. The critical currents (I_C) of tape after heat treatment at different annealing temperatures were tested at the liquid-nitrogen temperature. The microstructures and phase constituents of the tapes were investigated by SEM and XRD, respectively. The results indicate that annealing temperature has a very important influence on the superconducting properties of the tapes. When the temperature is above 840 °C, I_C value drops dramatically. Furthermore, when the temperature reaches up to 860 °C, the tape loses most of its superconducting property because of the decomposition of the superconducting phase Bi-2223.     

Influence of Precursor Powder Fabrication Methods on the Superconducting Properties of Bi-2223 Tapes

Bi-2223 precursor powders are prepared by both oxalate co-precipitation(CP) and spray pyrolysis(SP) methods.The influence of fabrication methods on the superconducting properties of Bi-2223 tapes are systematically studied. Compared to the CP method, SP powder exhibits spherical particle before calcination and smaller particle size after calcinations with more uniform chemical composition, which leads to a lower reaction temperature during calcination process for Bi-2223 tapes. Meanwhile, the non-superconducting phases in SP powder are more uniformly distributed with smaller particle sizes. These features result in finer homogeneity of critical current in large-length of Bi-2223 tape, higher density of filaments and better texture after heat treatment. Therefore,the SP method could be considered as a better route to prepare precursor powder for large-length Bi-2223 tape fabrication.     

Fabrication of joint Bi-2223/Ag superconducting tapes with BSCCO superconducting powders by diffusion bonding

61-Filaments Bi-2223/Ag superconducting tapes have been successfully joined with BSCCO superconducting powder interlayer by diffusion bonding. The electrical properties of the diffusion bonding joints were tested by standard four probe method and the microstructures of the joints were also examined by SEM. Additionally, the phase constituents of the superconducting powders between the tapes before and after bonding process were evaluated by XRD analysis. The result shows that the diffusion bonding joints are superconductive. The microstructures of the joint display a good bonding with no cracks and discontinuities. The joining zones are mainly composed of Bi-2223 phase, Bi-2212 phase and a small amount of CuO, Ca₂PbO₄. At last, the phase transformations of the superconducting powders in the bonding process are discussed.     

熔融织构YBCO块材和Bi-2223/Ag带材磁光图像研究的评述

熔融织构YBCO块材表面的磁感应强度在空间的分布和随时间的变化可以用磁光图像观测.熔融织构YBCO块材的l临界电流密度成功地由饱和抗磁场确定.局域电流密度随时间变化的反常行为从不同磁通动力学模型随空间的时间的转换理解.Bi-2223/Ag带材超导芯中的片晶中的电流密度在67K可达1.5×105A/cm2.由剩余磁感应强度的分布和超声振荡后的碎片证实的超导芯中的网状弱超导区是限制Bi-2223/Ag带材临界电流密度的主要原因.     

力学性能对Bi-2223/Ag超导带材临界电流影响实验研究

本文主要研究了在77K温度下,拉伸应变和弯曲应变对Bi-2223/Ag超导带材临界电流的影响,得到了超导带材的临界电流随拉伸强度、曲率半径变化规律.实验结果显明,拉伸作用在超导带材上产生的形变对其临界电流(Ic)的影响存在一个临界值εirr=0.3%.形变小于此临界值,Ic变化较小,超过此临界值,临界电流急剧下降.弯曲实验同样存在类似关系.同步辐射光源对超导带材检测表明,在形变情况下,超导氧化物陶瓷芯的微裂纹迅速增加和交织是Ic降低的主要原因.     

Bi-2223/AgAu 带材及应用进展

Bi-2223/AgAu 高温超导带材因为较低的热导率和较高的载流性能, 被认为是制备高温超导电流引线的最佳材料之一. 这篇文章简单介绍了高温超导电流引线的工作特点和不同包套 Bi-2223 带材的热导率, 在此基础上详细介绍了目前 Bi-2223/AgAu 带材和高温超导电流引线国内外研究进展, 最后展望了 Bi-2223 带材的发展趋势.     

添加超导中间层扩散连接BSCCO带材

采用超导粉末作中间层对BSCCO带材进行连接是比较有效的方法.超导粉末中间层中Bi-2223超导相的含量影响着连接的效果,超导相含量为88.5%的中间层连接所得到的接头的连接效率比含量为55%的中间层连接的接头的连接效率高18个百分点.另外在超导粉末中间层中添加适量的金属Ag可以有效的降低中间层的熔点,增加中间层的粘性,减少连接的缺陷,提高连接的质量.     

Investigation of Bi-2223 high temperature superconducting tape as the material for gradient coil in MRI

The use of Bi-2223 high temperature superconducting (HTS) tape as a material for gradient coils in MRI is evaluated in this paper. Bi-2223 tapes have a very high critical current and a very low power loss. A HTS tape gradient coil is expected to provide much higher gradient strength and generate much lower heating than a copper coil. Measurements of the AC power loss of Bi-2223 tapes at typical operating frequencies for gradient coils are presented. The degradation of the critical current and its effect on the increase of AC power loss is analyzed. Practical technical issues such as resistance, gradient strength and mechanical performance are also discussed. A prototype Bi-2223 HTS tape gradient coil is evaluated to verify the concept.     

Bi-2223喷雾热分解粉末热处理工艺优化

Bi-2223 带材目前在电流引线、 超导电机、 超导电缆、 超导限流器等领域实现了许多示范性应用, 载流性能是表征其性能的重要指标, 而高质量的前驱体粉末是最终带材性能的关键保障. 本文选用具有工艺简单、 粉末效率高、 批次稳定性好等优点的喷雾热分解法制备的Bi-2223 前驱体粉末, 利用 TG-DSC、XRD、SEM 等测试手段对低氧条件下不同保温时间烧结的粉末进行分析, 并结合最终带材的载流性能测试结果, 获得了最优粉末烧结参数, 为后续喷雾热分解粉末的进一步生成 Bi-2223 相以及高性能粉末的制备提供了依据.     

ITER电流引线高温超导叠制作工艺及性能测试

ITER高温超导电流引线载流能力最大要达到68 kA,一根电流引线共需要1000多根银金基Bi-2223高温超导带并联.这些高温超导带分成90叠,每叠由12层带组成.银金基Bi-2223带价格是普通银基Bi系带的4～5倍,而目前欧洲超导公司提供的超导叠的报价几乎是其带价格加倍,所以开发超导叠的制作工艺是非常有价值的.本文详细的介绍了超导叠的真空钎焊制作工艺,并进行了77 K下超导带的接头电阻测试和77 K自场下的临界电流测试,以及模拟在实际运行温度65～5 K条件下高温超导叠的载流能力测试和接头电阻的测试.测试结果证明了此工艺的可行性.     

外场下机械振动对高温超导带材交流损耗的影响

高温超导带材在磁场中传输交变电流时,将受到电磁力的作用而产生机械振动,振动对带材的交流损耗将产生影响.本文讨论了振动情况下交流损耗的测量方法,在平行于带面的直流磁场下,测量了Bi-2223/Ag高温超导带材在不同振动情况下的交流损耗.结果显示:当传输电流频率偏离样品的共振频率时,振动对带材的交流损耗影响不大;只有当电流频率在共振频率附近时,样品产生剧烈振动,交流损耗才有明显的增加;另外,带材振动时的交流损耗随频率变化曲线的斜率比不振动时略有增加.     

Reactivity and oxygen diffusion property of resistive barriers for Bi-2223/Ag tapes

Reactivity of several oxide materials (OM) with BSCCO powder and oxygen diffusion through OM layer has been tested at temperature ≈840 °C in air. The OM (e.g.: BaZrO₃, SrCO₃, MgO and ZrO₂) showing the low or no reactivity with BSCCO have been mixed (10 wt.%) with precursor powder and used for single-core tapes. Bi-2223/Ag/OM/Ag single-core tapes with oxide barriers made of BaZrO₃, SrCO₃, ZrO₂ and Al₂O₃ have been also prepared by a standard powder-in-tube technique. The used OM in the direct contact with BSCCO influences the electrical properties of Bi-2223 phase differently. These is because the oxides react with BSCCO during the heat treatment and simultaneously affect the 2212→2223 phase transformation, the Bi-2223 grain growth and so also grain connectivity. SrCO₃ powder has been evaluated as the best material from the point of no destructive effect on 2223 phase transport current property. The oxide barrier controls the oxygen diffusion during the tape heat treatment and simultaneously the HTS phase formation kinetics, its purity and content within the superconducting core. For single-core Bi-2223/Ag/OM/Ag tapes, the highest current density was measured for Al₂O₃ due to only slightly reduced oxygen diffusion through the barrier.     

Decrease of magnetic AC loss in twisted-filament Bi-2223 tapes

In AC power-engineering applications, a large part of the AC loss in the superconductor is due to magnetization by the external field. This magnetic AC loss has been well described for the low-T_c conductors. In Bi-2223 tapes the picture is different due to strong anisotropy, granularity and flux creep. Magnetic AC loss in various twisted and non-twisted Bi-2223 tapes has been measured at power frequencies by a pickup method. The results are compared to theoretical models of magnetization loss. When the field is parallel to the tape plane, the filaments in twisted tapes can be decoupled and the AC loss is decreased even when the matrix is pure silver. The extra effect of higher-resistance matrix materials is studied. In perpendicular field it is more difficult to decouple the filaments, due to the particular tape geometry. Contrary to a wire, there are essential differences between the AC loss mechanisms in a long twisted tape and those in a short piece of non-twisted tape. Finally, the dynamic resistance caused by the AC magnetic field is examined.     

The frequency dependence of AC transport losses in stacked Bi—2223／Ag superconducting tapes

AC transport losses in a single superconducting tape, double-and triple-stacked Bi-2223/Ag superconducting tapes were measured by use of electrical method. The measurements were carried out at 77K with the frequency of AC transport currents ranging from 50 to 100Hz. The dependence of AC losses on frequency and the number of tapes in the stack were presented and analysed.     

磁约束等离子体推进器高温超导磁体系统的电磁计算

在地面实验中磁约束等离子体推进器磁体系统是靠四个NbTi低温超导磁体提供磁场,现在设计依靠G-M制冷机传导制冷的由Bi2223超导带材绕制成的四个高温超导磁体替代以前的四个低温超导磁体.本文利用ANSYS有限元分析软件进行电磁计算,得出高温超导磁体的参数。     

Superconducting joint of Bi-2223/Ag superconducting tapes by diffusion bonding

61-Filaments Bi-2223/Ag superconducting tapes have been joined by diffusion bonding. The critical currents (I_Cs) of the joints are obtained by using standard four probe method under no magnetic field in the liquid nitrogen. The microstructures of the joints are evaluated by the electron microscope in electron backscatter diffraction mode and the phase compositions of the superconducting cores of the joint and the original tape are determined by X-ray diffraction (XRD). The results show diffusion bonding is effective bonding technique for HTS tapes, and the bonding time is reduced greatly from hundreds of hours to a few hours, and the bonding pressure also changes from 140–4000 MPa to 3 MPa. Furthermore, the diffusion bonding joints sustain superconducting properties, and the critical current ratios (CCR_O) of the joints are in the range of 35%–80%. Microstructures of the typical joint display a good bonding and some defects existed in traditional method are avoided. XRD results show that the phase compositions of the superconducting cores have no obvious changes before and after diffusion bonding, which offers physical and material bases for high superconducting property of the joints.     

Comparative study on the critical current performance of Bi-2223/Ag and YBCO wires in low magnetic fields at liquid nitrogen temperature

A comparative study on the critical current performance of Bi-2223/Ag and YBCO coated conductor wires in low magnetic fields at liquid nitrogen temperature was carried out in this work. Five commercial high temperature superconductor wires from different manufacturers were collected. Their critical currents were measured in magnetic fields, ranging from 0 to 0.4 T. On contrary to the common conception, the Bi-2223/Ag samples had better performance than YBCO coated conductor samples in the magnetic fields parallel to the wide surface of superconducting wires within the experimental scope. We also found similar results by collecting the concerned datum from the published literatures to confirm our measurement results. At the present stage, this fact made that the Bi-2223/Ag wires might be the preferred choice for the applications with mainly low parallel fields involved, unless other considerations were prioritized.