Mg0.9Zr0.1B2/Cu wires were successfully synthesized by SHS method in the air

Mg_0.9Zr_0.1B₂/Cu wires were successfully synthesized by powder-in-tube (PIT) techniques with self-propagating high-temperature synthesis (SHS) method. We loaded the mixed of Mg, Zr and B power into Cu tube. The tube was drawn to a wire and each end of the tube was sealed by the sealant, then rolled into solenoid with 1.5 cm diameter. The wire was heated up to 270 °C in a furnace with general air pressure, then, ignited the wire with electric arc from one of the end, the self-propagating reaction was completed in 2.0–2.5 s. Finally, the prepared wire was followed by furnace cooling to room temperature. The sample was examined using XRD, SEM, and magnetization measurements. The experiments show that there are small MgCu₂ and boron-rich phases inner sheath wall of copper tube. The magnesium oxide is small in the sample. So, PIT technologies with SHS method is effective in stopping the volatile and oxidize of magnesium. The J_c results show that Mg_0.9Zr_0.1B₂/Cu wires samples which were synthesized by SHS method are better than those sintered for 1 h and Cu clad pure MgB₂ wire. The highest J_c of the prepared Mg_0.9Zr_0.1B₂/Cu wire by SHS method in the air is 5.1 × 10⁵ A/cm² (5 K, 0.5 T), 1.4 × 10⁵ A/cm² (20 K, 1 T) and 4.3 × 10⁴ A/cm² (30 K, 0.5 T).     

Large transport critical currents of powder-in-tube Sr0.6K0.4Fe2As2/Ag superconducting wires and tapes

We report the achievement of transport critical currents in Sr_0.6K_0.4Fe₂As₂ wires and tapes with a T_c = 34 K. The wires and tapes were fabricated through an in situ powder-in-tube process. Silver was used as a chemical addition as well as a sheath material. All the wire and tape samples have shown the ability to transport superconducting current. Critical current density J_c was enhanced upon silver addition, and at 4.2 K, a largest J_c of ～1200 A/cm² (I_c = 9 A) was achieved for 20% silver added tapes, which is the highest in iron-based wires and tapes so far. The J_c is almost field independent between 1 T and 10 T, exhibiting a strong vortex pinning. Such a high transport critical current density is attributed to the weak reaction between the silver sheath and the superconducting core, as well as an improved connectivity between grains. We also identify a weak-link behavior from the apparent drop of J_c at low fields and a hysteretic phenomenon. Finally, we found that compared to Fe, Ta and Nb tubes, Ag was the best sheath material for the fabrication of high-performance 122 type pnictide wires and tapes.     

Effect of processing temperature on the superconducting properties of acetone doped MgB2 tapes

Correlation of phase formation, critical transition temperature T_c, microstructure, and critical current density J_c with sintering temperature has been studied for acetone doped MgB₂/Fe tapes. Sintering was performed at 600–850 °C for 1 h in a flowing Ar atmosphere. High boron substitution by carbon was obtained with increasing the sintering temperature; however, the acetone doped samples synthesized at 800 °C contain large size MgB₂ grains and more MgO impurities. Incomplete reaction for the acetone doped samples heated at 600 °C result in bad intergrain connectivity. At 4.2 K, the best J_c value was achieved in the acetone doped sample sintered at 700 °C, which reached 24,000 A/cm² at 10 T and 10,000 A/cm² at 12 T, respectively. Our results indicate that the small grain size and less impurity were also important for the improvement of J_c–B properties besides the substitutions of B by C.     

Synthesis and characterization of excess magnesium MgB2 superconductor under inert carbon environment

The structural, transport and magnetic properties of MgB₂ superconductor heavily blended with Mg is studied. The samples are synthesized with a new approach in both, pressed carbon environment and in flowing argon. The excess magnesium used is observed to play dual role: one being the prevention of Mg losses during the synthesis process and hence maintaining the stoichiometry of MgB₂ phase, and second being the formation of Mg milieu probably all around the MgB₂ grains to give a dense structure. Excess Mg also improves the grain connectivity by going into the pores and there by minimizing the insulating junctions. The residual resistivity of the sample is observed to decrease from 57.02 μΩ cm to 10.042 μΩ cm as it is progressively filled with superconductor–normal–superconductor (SNS) type junctions amongst the grains by the virtue of increased magnesium content. The synthesized samples devoid of porosity show the superconducting transition, T_c in the range of 39–34 K as of clean MgB₂ samples, though overloaded with Mg. The excess Mg resulted in enhanced critical current density, J_c from 6.8 × 10³ A cm^?2 to 5.9 × 10⁴ A cm^?2 at 20 K and 10 kOe, with reasonable decrease in the superconducting transition. Thus our samples being overloaded with Mg impart mechanical strength and competitive superconducting properties, which forms a part of interest.     

Thickness dependence of Ic and Jc of LTG-SmBCO coated-conductor on IBAD-MgO tapes

We have reported SmBa₂Cu₃O_y (SmBCO) films on single crystalline substrates prepared by low-temperature growth (LTG) technique. The LTG-SmBCO films showed high critical current densities in magnetic fields compared with conventional SmBCO films prepared by pulsed laser deposition (PLD) method. In this study, to enhance critical current (I_c) in magnetic field, we fabricated thick LTG-SmBCO films on metal substrates with ion-beam assisted deposition (IBAD)-MgO buffer and estimated the I_c and J_c in magnetic fields.All the SmBCO films showed c-axis orientation and cube-on-cube in-plane texture. T_c of the LTG-SmBCO films were 93.1–93.4 K. J_c and I_c of a 0.5 μm-thick SmBCO film were 3.0 MA/cm² and 150 A/cm-width at 77 K in self-field, respectively. Those of a 2.0 μm-thick film were 1.6 MA/cm² and 284 A/cm-width respectively. Although I_c increased with the film thickness increasing up to 2 μm, the I_c tended to be saturated in 300 A/cm-width. From a cross sectional TEM image of the SmBCO film, we recognized a-axis oriented grains and 45° grains and Cu–O precipitates. Because these undesired grains form dead layers, I_c saturated above a certain thickness. We achieved that I_c in magnetic fields of the LTG-SmBCO films with a thickness of 2.0 μm were 88 A/cm-width at 1 T and 28 A/cm-width at 3 T.     

Influence of Zr and Ce doping on electromagnetic properties of (Gd,Y)–Ba–Cu–O superconducting tapes fabricated by metal organic chemical vapor deposition

(Gd,Y)Ba₂Cu₃O_x tapes have been fabricated by metal organic chemical vapor deposition (MOCVD) with Zr-doping levels of 0–15 mol.% and Ce doping levels of 0–10 mol.% in 0.4 μm thick films. The critical current density (J_c) of Zr-doped samples at 77 K, 1 T applied in the orientation of H 6 c is found to increase with Zr content and shows a maximum at 7.5% Zr doping. The 7.5% Zr-doped sample exhibits a critical current density (J_c) of 0.95 MA/cm² at H 6 c which is more than 70% higher than the J_c of the undoped sample. The peak in J_c at H 6 c is 83% of that at H 6 a–b in the 7.5% Zr-doped sample which is more than twice as that in the undoped sample. Superconducting transition temperature (T_c) values as high as about 89 K have been achieved in samples even with 15% Zr and 10% Ce. Ce-doped samples with and without Ba compensation are found to exhibit substantially different J_c values as well as angular dependence characteristics.     

Effects of doping with nanoscale Co3O4 particles on the superconducting properties of powder-in-tube processed MgB2 tapes

Nanoscale Co₃O₄ particles were doped into MgB₂ tapes with the aim of developing superconducting wires with high-current-carrying capacity. Fe-sheathed MgB₂ tapes with a mono-core were prepared using the in situ powder-in-tube (PIT) process with the addition of 0.2–1.0 mol% Co₃O₄. The critical temperature decreased monotonically with an increasing amount of doped Co₃O₄ particles for all heat-treatment temperatures from 600 to 900 °C. However, the transport critical current density (J_c) at 4.2 K varied with the heat-treatment temperatures. The J_c values in magnetic fields ranging from 7 to 12 T decreased monotonically with increasing Co₃O₄ doping level for a heat-treatment temperature of 600 °C. In contrast, some improvements on the J_c values of the Co₃O₄ doped tapes were observed in the magnetic fields below 10 T for 700 and 800 °C. Furthermore, J_c values in all the fields measured increased as the Co₃O₄ doping level increase from 0 to 1 mol% for 900 °C. This heat-treatment temperature dependence of the J_c values could be explained in terms of the heat-treatment temperature dependence of the irreversibility field with Co₃O₄ doping.     

Intrinsic pinning properties of FeSe0.5Te0.5

The intrinsic pinning properties of FeSe_0.5Te_0.5, which is a superconductor with a critical temperature T_c of approximately 14 K, were studied through the analysis of magnetization curves obtained using an extended critical state model. For the magnetization measurements carried out with a superconducting quantum interference device (SQUID), external magnetic fields were applied parallel and perpendicular to the c-axis of the sample. The critical current density J_c under the perpendicular magnetic field of 1 T was estimated using the Kimishima model to be equal to approximately 1.6 × 10⁴, 8.8 × 10³, 4.1 × 10³, and 1.5 × 10³ A/cm² at 5, 7, 9, and 11 K, respectively. Furthermore, the temperature dependence of J_c was fitted to the exponential law of J_c(0) × exp(?αT/T_c) up to 9 K and the power law of J_c(0) × (1 ? T/T_c)ⁿ near T_c.     

Aqueous polymer–nitrate solution deposition of YBCO films

High critical current density YBa₂Cu₃O_7?x (YBCO) films were prepared by solution deposition of aqueous non-fluorine precursors. Non-fluorine polymer-assisted deposition (PAD) processes utilizing rheology modifiers and chelating agents were used to produce 50 nm films with a critical current density (J_c) over 3 MA/cm² and 400 nm films with J_c > 1 MA/cm²_. T_c measurements indicated that films have T_c values near 90 K. The total heat treatment time to produce these high performance films was less than 4 h. Rheology modifiers such as polyvinyl alcohol (PVA) and hydroxyethyl cellulose (HEC) were used to increase the thickness of deposited films independent of the solution cation concentration. Chelating agents such as polyethylene glycol (PEG) and sucrose increased the barium ion solubility. Nitrate crystallization during deposition was controlled through rapid drying with vacuum and coating with hot solutions.     

Effects of copper doping in MgB2 superconductor

Magnesium diboride, recently discovered as superconductor, is extremely interesting in respect to pairing mechanisms and phonon-mediated superconductivity, but its transition temperature (39 K) is decidedly too low for practical applications. A rush for substitutions started, intended to raise T_c and possibly maintain acceptable critical current density. The difficult introduction of Cu was attempted, through a complex procedure employing CuB₂₄ instead of metallic Cu: owing to the tendency of Cu to form inter-metallic compounds with Mg, only a maximum of 3 mol% of Cu was safely substituted to Mg in MgB₂ lattice and a small parameters contraction proportional to Cu content was recorded. The results are a decrease in T_c of about 0.5 K, not far from that found with Al addition, whose reasons are discussed and interpreted in terms of holes doping.     

Carbon doping of MgB2 by toluene and malic-acid-in-toluene

The decomposition of malic acid (C₄H₆O₅) in the presence of Mg and B was studied using Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA) which revealed that malic acid reacted with Mg but not B. Also, the addition of toluene (C₇H₈) to dissolve malic acid followed by subsequent drying resulted in no reaction with Mg, indicating that the malic acid had decomposed during the dissolution/drying stage. The total carbon contributed by toluene versus a toluene/5 wt.% malic acid mixture was measured using a LECO CS600 carbon analyzer. The toluene sample contained ～0.4 wt.% C while the toluene/malic acid mixture had ～1.5 wt.% C, demonstrating that the toluene contributed a significant amount of carbon to the final product. Resistivity measurements on powder-in-tube MgB₂ monofilamentary wires established that the toluene/malic acid doped sample had the highest B_c2. However, the toluene-only sample had the highest transport J_c over most of the magnetic field range (0–9 T), equaled only by that of toluene/malic-acid sample in fields above 9 T.     

Critical current density in MgB2 bulk samples after co-doping with nano-SiC and poly zinc acrylate complexes

The co-doped MgB₂ bulk samples have been synthesized using an in situ reaction processing. The additives is 8 wt.% SiC nano powders and 10 wt.% [(CH₂CHCOO)₂Zn]_n poly zinc acrylate complexes (PZA). A systematic study was performed on samples doped with SiC or PZA and samples co-doped with both of them. The effects of doping and co-doping on phase formation, microstructure, and the variation of lattice parameters were studied. The amount of substituted carbon, the critical temperature (T_c) and the critical current density (J_c) were determined. The calculated lattice parameters show the decrease of the a-axis, while no obvious change was detected for c-axis parameter in co-doped samples. This indicates that the carbon was substituted by boron in MgB₂. The amount of substituted carbon for the co-doped sample shows an enhancement compared to that of the both single doped samples. The co-doped samples perform the highest J_c values, which reaches 3.3 × 10⁴ A/cm² at 5 K and 7 T. It is shown that co-doping with SiC and organic compound is an effective way to further improve the superconducting properties of MgB₂.     

Textured Sr1−xKxFe2As2 superconducting tapes with high critical current density

A critical issue in depressing critical current density in polycrystalline iron pnictides is intrinsic weak-link behavior. Using well established, industrial scalable, deformation processes, we have achieved c-axis aligned grains in powder-in-tube Sr_0.6K_0.4Fe₂As₂ tapes. This is followed by a short high-temperature annealing to enhance the connectivity. The resultant Sr_1?xK_xFe₂As₂ superconducting tapes have transport critical current densities exceeding 5000 A/cm² at 4.2 K in self field. This advance open up possibilities for fabricating iron-based superconducting tapes capable of carrying high currents.     

Critical properties of superconducting Ba1−xKxFe2As2

Magnetisation and magneto-resistance measurements have been carried out on superconducting Ba_1?xK_xFe₂As₂ samples with x = 0.40 and 0.50. From high field magnetization hysteresis measurements carried out in fields up to 16 T at 4.2 K and 20 K, the critical current density has been evaluated using the Bean critical state model. The J_C determined from the high field data is >10⁴ A/cm² at 4.2 K and 5 T. The superconducting transitions were also measured resistively in increasing applied magnetic fields up to 12 T. From the variation of the T_C onset with applied field, dH_C2/dT at T_C was obtained to be ?7.708 T/K and ?5.57 T/K in the samples with x = 0.40 and 0.50.     

Effect of W-addition on pinning property of MgB2

The 5d transition metal W was added into the MgB₂ superconductor. The Mg, B and W were sintered at 1173 K for 30 min under H₂/Ar atmosphere in the electric furnace. The W_x(MgB₂)_1?x samples were prepared in the W concentration range of 0 ? x ? 0.05. Temperature and field dependences of magnetization were measured by the SQUID magneto-meter. The field and x dependences of J_c at 20 K were analyzed by the extended critical state model. The enhancement of J_c became maximum for the x = 0.02 sample.     

Effect of the composition on the superconducting properties of IBAD-MgO SmBCO coated conductors with superconducting film directly deposited on epi-MgO layer

Sm_1+xBa_2?xCu_3+yO_7?δ (SmBCO) films were directly deposited on the epi-MgO/IBAD-MgO/Y₂O₃/Al₂O₃/Hastelloy template by co-evaporation using the evaporation using drum in dual chambers (EDDC) system without the buffer layer in order to investigate the effect of the composition ratios on superconducting property, microstructure and texture of SmBCO film. The films with gradient composition ratios of Sm:Ba:Cu were deposited using a shield with an opening which was placed between the substrate and the boats. The highest I_c of 52 A (corresponding to J_c = 1.6 MA/cm² and a thickness of 800 nm) was observed at 77 K in self field at a composition x = 0.01–0.05 and y = ?0.23 to ?0.46. When the composition ratio is outside this range, the I_c value rapidly decreased. The superconducting critical current was highly dependent on the composition ratio. As the composition ratio is farther away from that of the highest I_c, the SmBCO (1 0 3) peak intensity increased and the amount of a-axis oriented parts increased. A dense microstructure with round-shape grains was observed in the region showing the highest I_c. The optimum composition ratio can be found by analyzing films deposited with variable deposition rates of each depositing element.     

Fabrication and characterization of iron pnictide wires and bulk materials through the powder-in-tube method

The recent discovery of superconductivity in the iron-based superconductors with very high upper critical fields presents a new possibility for practical applications, but fabricating fine-wire is a challenge because of mechanically hard and brittle powders and the toxicity and volatility of arsenic. In this paper, we report the synthesis and the physical characterization of iron pnictide wires and bulks prepared by the powder-in-tube method (PIT). A new class of high-T_c iron pnictide composite wires, such as LaFeAsO_1?xF_x, SmFeAsO_1?xF_x and Sr_1?xK_xFeAs, has been fabricated by the in situ PIT technique using Fe, Ta and Nb tubes. Microscopy and X-ray analysis show that the superconducting core is continuous, and retains phase composition after wire drawing and heat treatment. Furthermore, the wires exhibit a very weak J_c-field dependence behavior even at high temperatures. The upper critical field H_c2(0) value can exceed 100 T, surpassing those of MgB₂ and all the low temperature superconductors and indicating a strong potential for applications requiring very high field. These results demonstrate the feasibility of producing superconducting pnictide composite wire. We also applied the one-step PIT method to synthesize the iron-based bulks, due to its convenience and safety. In fact, by using this technique, we have successfully discovered superconductivity at 35 K and 15 K in Eu_0.7Na_0.3Fe₂As₂ and SmCoFeAsO compounds, respectively. These clearly suggest that the one-step PIT technique is unique and versatile and hence can be tailored easily for other rare earth derivatives of novel iron-based superconductors.     

In situ characterization of transport properties of superconducting (Cu, C)-system thin films

Transport properties of (Cu, C)Ba₂CuO_x [(Cu, C)-1201] thin films have been characterized by in situ temperature dependence of resistivity, without breaking vacuum from the deposition to the measurement. In in situ transport properties measurements, the obtained results reveal that (Cu, C)Ba₂CuO_x films exhibit T_c > 20 K on the cased of conductivity at 290 K (σ_[290 K]) > 4 × 10² S/cm and temperature coefficient of resistivity (TCR) > 1.5 × 10^?3 K^?1, and doping level of them should be in between under-doped and optimally-doped states. Their results suggest that there would be possible to further increases of T_c, and XPS data suggest that (Cu, C)-system should have the excellent dopability in their charge reservoir and the possibility of low anisotropy.     

Effects on Jc of pinning center morphology for multiple-in-line-damage in coated conductor and bulk,melt-textured HTS

The properties of discontinuous aligned pinning centers (PCs) created by high-energy heavy-ions are compared for bulk melt-textured and coated conductor HTS. Properties of PCs, which increase J_c (pinning potential and entanglement), and negative properties which decrease J_c (e.g., decreased T_c and percolation paths) are evaluated. Mechanisms are proposed to explain the very large increases in J_c resulting from multiple-in-line-damage (MILD) compared to continuous columnar pinning centers (CCPC). In particular, a mechanism which results in fluxoid entanglement, even for parallel (unsplayed) PCs, is discussed. The same mechanism is found to also account for restoration of much of the pinning potential expected to be lost due to the gaps in MILD PCs. It also accounts for the fact that at high fluence, J_c increases as fluence is increased, instead of decreasing as expected. The very low self-field in coated conductor permits separation of the negative and positive effects of PCs. It is found that parameters developed to quantify the negative effects in bulk melt-textured YBCO, by 63 GeV U²³⁸ ions, successfully describe damage to 2.1 μm thick coated conductor by 1 GeV Ru⁴⁴ ions. Coated conductor at 77 K and self-field is generally known to have J_c about 100 times that of melt-textured YBCO. However, at 77 K and applied field of 1 T, when both forms of HTS are processed with comparable numbers of near-optimum MILD PCs, the difference in J_c is reduced to a factor of 1.3–2. Whereas J_c for melt-textured YBCO increased sharply, by a factor of up to 16.8 for high-fluence MILD PCs, J_c in coated conductor increased by a smaller factor of 2.5–3.0. Nevertheless, 2.1 μm thick coated conductor, with near-optimum MILD PCs, exhibits J_c = 543 kA/cm² at 77 K and applied field of 1.0 T, and I_c = 114 A/cm-width of conductor. This is the highest value we find in the literature. The phenomenology developed indicates that for optimum MILD PCs in coated conductor, J_c ～ 700 ± 70 kA/cm² should be achievable at 77 K, 1.0 T.     

Deposition of Gd2Zr2O7 single buffer layers with different thickness for YBa2Cu3O7−δ coated conductors on metallic substrates

A series of Gd₂Zr₂O₇ (GZO) single buffer layers with different thicknesses were epitaxially grown on highly textured Ni–5 at.% W tapes using pulsed laser deposition. These allow the subsequent growth of high-quality superconducting YBa₂Cu₃O_7?δ layers. The superconducting transition temperature T_c reaches a maximum value of 92.4 K as well as a narrow transition width of 0.8 K for the optimized GZO layer thickness. The inductive measurements show the critical current density as high as 1.2 MA/cm² at 77 K in self-field, indicating that a GZO single buffer layer is a suitable alternative for simplifying the second generation high T_c superconducting coated conductors architecture.