Anion-correlated conduction band edge shifts and charge transfer kinetics in dye-sensitized solar cells with ionic liquid electrolytes

In solvent-free ionic liquid electrolytes for efficient dye-sensitized solar cells, iodide and non-iodide melts are ordinarily blended in order to attain a high dynamic fluidity and thereby meet a fast mass transport of electroactive species. This common tactic could bring forth a prominent impact of various anions on cell efficiency by altering photocurrent and/or photovoltage. Herein we report evident effects of the dicyanamide versus tetracyanoborate anion on the energetics of titania conduction band edge and the kinetics of multi-channel charge-transfer reactions in cells employing a high absorption coefficient ruthenium sensitizer C106. A slightly shorter photoluminescence lifetime of C106 grafted on alumina is probed for the tetracyanoborate-based reference cell with respect to the dicyanamide counterpart. However, owing to a more favourable thermodynamic driving force of ～90 meV, the tetracyanoborate anion prompts an almost 3-fold faster electron injection from the excited-state dye to titania than dicyanamide, leading to a higher charge separation yield, which is in good agreement with an almost indistinguishable ratio of external quantum efficiency enhancement in the whole spectral response region. Compared to tetracyanoborate, the presence of dicyanamide at the titania/electrolyte interface evokes a 27-fold smaller interfacial electron exchange rate (K) with triiodide, accounting for the open-circuit photovoltage variation observed in current-voltage measurements.     

Stable mesoscopic dye-sensitized solar cells based on tetracyanoborate ionic liquid electrolyte

A stable dye-sensitized solar cell has been obtained based on a new binary ionic liquid electrolyte system containing 1-propyl-3-methylimidazolium iodide and 1-ethyl-3-methylimidazolium tetracyanoborate.     

High efficiency dye-sensitized nanocrystalline solar cells based on ionic liquid polymer gel electrolyte

An ionic liquid polymer gel containing 1-methyl-3-propylimidazolium iodide (MPII) and poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) has been employed as quasi-solid-state electrolyte in dye-sensitized nanocrystalline TiO2 solar cells with an overall conversion efficiency of 5.3% at AM 1.5 illumination.     

Structure and dynamics of a confined ionic liquid. Topics of relevance to dye-sensitized solar cells

The behavior of a model ionic liquid (IL) confined between two flat parallel walls was studied at various interwall distances using computer simulations. The results focus both on structural and dynamical properties. Mass and charge density along the confinement axis reveal a structure of layers parallel to the walls that leads to an oscillatory profile in the electrostatic potential. Orientational correlation functions indicate that cations at the interface orient tilted with respect to the surface and that any other orientational order is lost thereafter. The diffusion coefficients of the ions exhibit a maximum as a function of the confinement distance, a behavior that results from a combination of the structure of the liquid as a whole and a faster molecular motion in the vicinity of the walls. We discuss the relevance of the present results and elaborate on topics that need further attention regarding the effects of ILs in the functioning of IL-based dye-sensitized solar cells.     

Anionic structure-dependent photoelectrochemical responses of dye-sensitized solar cells based on a binary ionic liquid electrolyte

Room temperature ionic liquids (RTILs) have been used as electrolytes to investigate the anionic structure dependence of the photoelectrochemical responses of dye-sensitized solar cells (DSCs). A series of RTILs with a fixed cation structure coupling with various anion structures are employed, in which 1-methyl-3-propylimidazolium iodide (PMII) and I(2) are dissolved as redox couples. It is found that both the diffusivity of the electrolyte and the photovoltaic performance of the device show a strong dependence on the fluidity of the ionic liquids, which is primarily altered by the anion structure. Further insights into the structure-dependent physical properties of the employed RTILs are discussed in terms of the reported van der Waals radius, the atomic charge distribution over the anion backbones, the interaction energy of the anion and cation, together with the existence of ion-pairs and ion aggregates. Particularly, both the short-circuit photocurrent and open-circuit voltage exhibit obvious fluidity dependence. Electrochemical impedance and intensity-modulated photovoltage/photocurrent spectroscopy analysis further reveal that increasing the fluidity of the ionic liquid electrolytes could significantly decrease the diffusion resistance of I(3)(-) in the electrolyte, and retard the charge recombination between the injected electrons with triiodide in the high-viscous electrolyte, thus improving the electron diffusion length in the device, as well as the photovoltaic response. However, the variation of the electron diffusion coefficients is trivial primarily due to the effective charge screening of the high cation concentration.     

An iodine-free electrolyte based on ionic liquid polymers for all-solid-state dye-sensitized solar cells

An ionic liquid polymer, poly (1-alkyl-3-(acryloyloxy)hexylimidazolium iodide), was employed as an iodine-free electrolyte in all-solid-state dye-sensitized solar cells with an overall conversion efficiency of 5.29% under AM 1.5 simulated solar light (100 mW cm(-2)) illumination.     

Solvent-free ionic liquid electrolytes without elemental iodine for dye-sensitized solar cells

A new type of electrolyte with a sulfide/polysulfide redox couple and I(-) was prepared as a solvent-free ionic liquid for application in dye-sensitized solar cells, reaching efficiencies of 5.2-6.4% under AM 1.5G, 100 mW cm(-2) light illumination, and 6.6% efficiency was obtained under 0.1 sun irradiation.     

Rubbery copolymer electrolytes containing polymerized ionic liquid for dye-sensitized solar cells

A novel type of random copolymer comprised of a polymerized ionic liquid, poly(1-((4-ethenylphenyl)methyl)-3-butyl-imidazolium iodide) (PEBII), and amorphous rubbery poly(oxyethylene methacrylate) (POEM) was synthesized and employed as a solid electrolyte in an I₂-free dye-sensitized solar cell (DSSC). The copolymer electrolytes deeply infiltrated into the nanopores of mesoporous TiO2 films, resulting in improved interfacial contact of electrode/electrolyte. The glass transition temperature (T _g) of the PEBII–POEM (?23 °C) was lower than that of PEBII homopolymer (?4 °C), indicating greater chain flexibility in the former. However, the DSSC efficiency of PEBII–POEM (4.5 % at 100 mW/cm²) was lower than that of PEBII (5.9 %), indicating that ion concentration is more important than chain flexibility. Interestingly, upon the introduction of ionic liquid, i.e., 1-methyl-3 propylimidazolium iodide, the efficiency of PEBII remained almost constant (5.8 %), whereas that of PEBII–POEM was significantly improved up to 7.0 % due to increased I^? ion concentration, which is one of the highest values for I₂-free DSSCs.     

Electrolytes for dye-sensitized solar cells based on interhalogen ionic salts and liquids

In this paper, we report on the preparation of interhalogen ionic liquids of the general formula [K+]XY2-, where K+=1,3-dialkylimidazolium, 1,2,3-trialkylimidazolium, or N-alkylpyridinium; XY2-=IBr2- or I2Br-. These compounds were characterized in solution and the solid state by NMR, IR, Raman, and mass spectroscopy. The crystal structure of the compound [Me2BuIm]IBr2 (7) shows that the IBr2- anion has a linear Br-I-Br structure. Indications of an equilibrium between different forms of XY2- anions in solution are observed. Interhalogen ionic salts and liquids were used as electrolyte components for encapsulated monolithic dye-sensitized solar cells. Overall light-to-electricity conversion efficiencies up to 6.4%, 5.0%, and 2.4% at 1000 W/m2 were achieved by using electrolytes based on interhalogen ionic salts and gamma-butyrolactone, glutaronitrile, or native ionic liquids as solvents, respectively. Moreover, in terms of stability, the cell performance lost 9-14% of the initial performance after 1000 h illumination at 350 W/m2.     

Co-sensitization of organic dyes for efficient ionic liquid electrolyte-based dye-sensitized solar cells

The co-sensitization of two organic dyes (SQ1 and JK2), which are complementary in their spectral responses, shows enhanced photovoltaic performance compared with that of an individual organic dye-sensitized solar cell. The power conversion efficiency of the co-sensitized organic dye solar cell based on the newly developed binary ionic liquid (solvent-free) electrolyte gives 6.4% under AM 1.5 sunlight at 100 mW/cm2 irradiation, which is higher than that of individual dye-sensitized solar cells. The incident monochromatic photon-to-current conversion efficiency (IPCE) of the co-sensitized solar cell shows typical absorption peaks at 530 and 650 nm corresponding to the two dyes and displays a broad spectral response over the entire visible spectrum with IPCE of >40% in the 400-700 nm wavelength domain.     

A supercooled imidazolium iodide ionic liquid as a low-viscosity electrolyte for dye-sensitized solar cells

A series of allyl-functionalized imidazolium salts are reported, including 1-allyl-3-ethylimidazolium iodide and 1-allyl-3-propylimidazolium iodide, which have melting points close to room temperature and show typical properties of supercooled fluids if heated above their melting points. Their viscosities in the liquid state are considerably lower than the benchmark ionic liquid used in solar cells, viz., 1-propyl-3-methylimidazolium iodide. Electrolytes containing these new liquids provide excellent efficiencies and good stability in dye-sensitized solar cells when subjected to an accelerated-light soaking test at 60 degrees C. The structures of three of the new salts have been established in the solid state by single-crystal X-ray analysis.     

A thiolate/disulfide ionic liquid electrolyte for organic dye-sensitized solar cells based on Pt-free counter electrodes

The ionic liquid, 1-ethyl-3-methylimidazolium tetracyanoborate, was employed to prepare a thiolate/disulfide ionic liquid electrolyte with low viscosity for organic dye-sensitized solar cells (DSCs). CoS was introduced and showed better photovoltaic performance in DSCs than the ubiquitous platinized FTO CE.     

Novel photosensitizer for dye-sensitized solar cell based on ionic liquid–doped blend polymer electrolyte

The existing energy situation demands not only the huge energy in a short time but also clean energy. In this regard, an integrated photo-supercapacitor device has been fabricated in which photoelectric conversion and energy storage are achieved simultaneously. A novel carbazole-based dye is synthesized and characterized for photosensitizer. The silver-doped titanium dioxide (Ag-TiO₂) is synthesized, and it is used as photoanode material. Different concentrations of tetrabutylammonium iodide (TBAI)-doped polyvinyl alcohol–polyvinylpyrrolidone (PVA-PVP) blend polymer electrolytes are prepared, and their conductivity and dielectric properties were studied. Reduced graphene oxide (r-GO) is synthesized by a one-pot synthesis method and confirmed using Raman spectroscopy for counter electrode material in dye-sensitized solar cell (DSSC) and supercapacitor electrodes. The DSSC having 4% Ag-TiO₂–based photoanode showed the highest efficiency of 1.06% (among r-GO counter electrodes) and 2.37% (among platinum counter electrodes). The supercapacitor before integration and after integration exhibits specific capacitance of 1.72 Fg⁻¹ and 1.327 Fg⁻¹, respectively.

Graphical Abstract

     

A novel deep eutectic solvent-based ionic liquid used as electrolyte for dye-sensitized solar cells

We utilize a quaternary ammonium salt-derivative ionic liquid called G.CI which is a eutectic mixture of glycerol and choline iodide as electrolyte for dye-sensitized solar cells. Such eutectic compound belongs to a new series of ionic liquid called deep eutectic solvents (DES), which possess many outstanding features compared to the traditional imidazolium-based ionic liquids including cheap raw materials, simple preparation procedures and better biocompatibility. Current–voltage characteristics of the G.CI/PMII-based binary electrolytes stand at 0.533 V on V_oc, 12.0 mA cm^?2 on J_sc, 0.582 on fill factor, and 3.88% cell efficiency under AM 1.5, 100 mW/cm² illuminations. The comparable cell performance together with all the above advantages makes G.CI as a strong candidate for future electrolyte development for dye-sensitized solar cells (DSSCs).     

A solvent-free, SeCN-/(SeCN)3- based ionic liquid electrolyte for high-efficiency dye-sensitized nanocrystalline solar cells

A solvent-free ionic liquid electrolyte based on the SeCN-/(SeCN)3- redox couple has been employed for high-efficiency dye-sensitized nanocrystalline solar cells. For the first time an alternative redox couple has been identified to rival and even exceed the performance of the iodide/triiodide couple even at full sunlight. Unprecedented 7.5-8.3% power conversion efficiencies under AM 1.5 sunlight have been achieved for photovoltaic devices with solvent-free ionic liquid electrolytes.     

Gelation of ionic liquid with exfoliated montmorillonite nanoplatelets and its application for quasi-solid-state dye-sensitized solar cells

The exfoliated montmorillonite (exMMT) nanoplatelets that carry negative charges are capable of adsorbing 1-methyl-3-propyl-imidazolium cations to form a gel-type ionic liquid-based electrolyte system for dye-sensitized solar cell (DSSC). Interestingly, it also increases the power conversion efficiency of DSSC from 6.58% to 7.77% at full sun. The increased efficiency is attributed to the decreased resistance of gel electrolyte system and enhanced reduction reaction rate at the counter electrode, both of which are related to the two-dimensional electrolyte nature of exMMTs that repel the I(-)/I(3)(-) redox couples toward their major conduction pathway.     

The promoting effect of a dicyanamide based ionic liquid in the selective hydrogenation of citral

Conventional supported heterogeneous palladium catalysts in combination with a dicyanamide based ionic liquid are highly active with excellent selectivity in enabling the one-pot synthesis of citronellal through citral hydrogenation.     

Influence of ionic liquids bearing functional groups in dye-sensitized solar cells

Ionic liquids containing the nitrile and vinyl functional groups attached to imidazolium cations combined with various anions, e.g., iodide, bis[(trifluoromethyl)sulfonyl]imide ([TFSI]-), or dicyanamide ([N(CN)2]-), have been prepared and characterized. These ionic liquids have been successfully used as electrolytes for dye-sensitized solar cells based on nanocrystalline TiO2 with the amphiphilic ruthenium sensitizer [ruthenium (4,4'-dicarboxylic acid-2,2'-bipyridine)(4,4'-bis(p-hexyloxystyryl)-2,2'-bipyridine)][NCS]2 (coded K-19). The iodide salt was used in 3-methoxypropionitrile-based electrolytes, and the performances of both types of devices were evaluated on the basis of their photocurrent density-voltage characteristics and dark current measurements, demonstrating that the functional groups do not exert a detrimental effect on the performance. The solid-state structure of the nitrile-functionalized salt [C1C3CN(im)]I has also been established by single-crystal X-ray diffraction, revealing extensive hydrogen bonding between the cation protons and the iodide.     

Composite electrolytes based on poly(ethylene oxide) and binary ionic liquids for dye-sensitized solar cells

The sunlight is the largest single available source of clean and renewable energy to ensure human society’s sustainable development. Owing to their low production cost and high energy conversion efficiency, dye-sensitized solar cells (DSSCs) have been regarded as good alternatives to conventional photovoltaic devices. Herein, a series of composite electrolytes based on poly(ethylene oxide) (PEO) and the binary ionic liquids 1-propyl-3-methy-imidazolium iodide ([PMIm]I) and 1-ethyl-3-methylimidazolium thiocyanate ([EMIm][SCN]) were prepared and then applied to fabricate six DSSCs. The composite electrolytes were characterized by fourier transform infrared spectroscopy (FTIS), X-ray diffraction (XRD), and electrochemical impedance spectra (EIS). It was shown that the addition of binary ionic liquids would reduce the degree of crystallinity of PEO, thus improving the ionic conductivities of the electrolytes by about 2 orders of magnitude. Investigation on the photovoltaic performances of these DSSCs showed that the fill factor (FF) could reach up to 0.67 and energy conversion efficiency (η) could reach up to 4.04% under AM 1.5 full sunlight (100 mW/cm2).