Monolithic capillary columns based on ethylene glycol dimethacrylate for separation of polymers by molecular mass

Polar monolithic capillary columns for the molecular-mass separation of polystyrene standards are synthesized on the basis of ethylene glycol dimethacrylate. The monolith structure is optimized through variation in the type of porogen because variation in other synthesis parameters (the time and temperature of polymerization, the amount of monomer in the initial feed) is inefficient. The separation of polymers on monolithic sorbents proceeds via a combined exclusion-hydrodynamic mechanism. In terms of a model that allows for contributions of both mechanisms to retention, calibration plots are drawn for the synthesized columns. Monolithic columns with the optimum monolith structure make it possible to use up to 60% of the column free volume for the efficient separation of polymers in a broad molecular-mass range.     

Effect of the nature of a porogen on the porous structure of monolithic polydivinylbenzene sorbents

In quartz capillaries, macroporous monolithic sorbents based on divinylbenzene are synthesized and their porous structure is studied via inverse size-exclusion-hydrodynamic chromatography. Either a single-component porogen (a higher alcohol) or a two-component porogen (a mixture of a higher alcohol and mesitylene) is used for the synthesis of monoliths. The removal of a solvent good for a polymer from a porogen results in an increase in the size of flow-through channels and a decrease in the free-space volume inside the monolith; this space is used for the separation of polymer sorbates (the working volume of a column). At the same time, the volume of micro- and mesopores in the monolith structure is practically independent of the content of the good solvent in the porogen. It is inferred that the good porogen plays an active role in formation of the macroporous structure of monoliths. The structure of monoliths obtained on the basis of the two-component porogen with the use of nonanol and mesitylene or toluene is optimum for the molecular-mass analysis of polymers.     

Improvement of proteome coverage using hydrophobic monolithic columns in shotgun proteome analysis

Monolithic columns are widely used in shotgun proteome analysis. However, it is difficult to increase the separation capability and proteome coverage by using conventionally organic polymer-based monolithic column due to the difficulty of controlling homogeneity of the overall pore structure (both pores and microglobules), which leads to relatively low column efficiency. Therefore, we studied the effect of constitute and percentage of porogenic solvent, functional monomer, column length, and separation gradient on the peak capacity and proteome coverage by methacrylate-based reversed phase monolithic columns. It was demonstrated that the porous property of the hydrophobic monolith, which was mainly determined by the porogenic solvent, was crucial to the proteome coverage when similar methacrylate monomer was utilized and a ternary porogenic solvent was adopted to prepare C12 monolithic column with relatively homogeneous overall pore structure. It was also shown that high proteome coverage could be reliably obtained with online multidimensional separation using totally monolithic columns system with the length of analytical column at 85 cm and reversed phase separation gradient at 210 min.     

The synthesis and study of monolithic capillary columns for ion chromatography of anions

The physicochemical and chromatographic parameters of ion-exchange monolithic matrices and capillary columns on their basis were measured. A method was suggested for producing high-efficiency ionexchange monolithic capillary columns with the monolith structure optimized for efficient selective separation of anions in ion chromatography. The influence of the conditions of synthesis of monoliths on their porosity, permeability, the structure of the monolith layer, and the impedance of monolithic columns on their basis was investigated. Original Russian Text ? A.A. Kurganov, A.A. Korolev, E.N. Viktorova, A.Yu. Kanat’eva, 2009, published in Zhurnal Fizicheskoi Khimii, 2009, Vol. 83, No. 2, pp. 375–379.     

Capillary monolithic titania column for miniaturized liquid chromatography and extraction of organo-phosphorous compounds

A new sol?Cgel protocol was designed and optimized to produce titanium-dioxide-based columns within confined geometries such as monolithic capillary columns and porous-layer open-tubular columns. A surface pre-treatment of the capillary enabled an efficient anchorage of the monolith to the silica capillary wall during the synthesis. The monolith was further synthesized from a solution containing titanium n-propoxide, hydrochloric acid, N-methylformamide, water, and poly(ethylene oxide) as pore template. The chromatographic application of capillary titania-based columns was demonstrated with the separation of a set of phosphorylated nucleotides as probe molecules using aqueous normal-phase liquid chromatography conditions. Capillary titania monoliths offered a compromise between the high permeability and the important loading capacity needed to potentially achieve miniaturized sample preparations. The specificity of the miniaturized titania monolithic support is illustrated with the specific enrichment of 5??-adenosine mono-phosphate. The monolithic column offered a ten times higher loading capacity of 5??-adenosine mono-phosphate compared with that of the capillary titania porous-layer open-tubular geometry.     

The Influence of the Natures of the Carrier Gas and the Stationary Phase on the Separating Properties of Monolithic Capillary Columns in Gas Adsorption Chromatography

A model mixture of light hydrocarbons was used to study the separation capacity of monolithic capillary columns based on divinylbenzene with five different carrier gases, including helium, hydrogen, nitrogen, carbon dioxide, and nitrous oxide. The results were correlated with the previously obtained data on monolithic columns based on silica gel. It was shown that the influence of the nature of the carrier gas was weaker than for silica gel columns; the polymeric columns studied behaved similarly to hollow capillary columns with polymeric stationary phases and exhibited an efficiency gain of 20–30% along the series He < H₂ < N₂ ～ N₂O < CO₂. Based on the minimum HETP (～15 μm) obtained for the investigated monolithic columns under optimum conditions with N₂O or CO₂ as a carrier gas, the conclusion was drawn that the creation of divinylbenzene-based monolithic capillary columns with a high specific efficiency was possible.     

High-efficiency peptide analysis on monolithic multimode capillary columns: Pressure-assisted capillary electrochromatography/capillary electrophoresis coupled to UV and electrospray ionization-mass spectrometry

High-efficiency peptide analysis using multimode pressure-assisted capillary electrochromatography/capillary electrophoresis (pCEC/pCE) monolithic polymeric columns and the separation of model peptide mixtures and protein digests by isocratic and gradient elution under an applied electric field with UV and electrospray ionization-mass spectrometry (ESI-MS) detection is demonstrated. Capillary multipurpose columns were prepared in silanized fused-silica capillaries of 50, 75, and 100 microm inner diameters by thermally induced in situ copolymerization of methacrylic monomers in the presence of n-propanol and formamide as porogens and azobisisobutyronitrile as initiator. N-Ethylbutylamine was used to modify the chromatographic surface of the monolith from neutral to cationic. Monolithic columns were termed as multipurpose or multimode columns because they showed mixed modes of separation mechanisms under different conditions. Anion-exchange separation ability in the liquid chromatography (LC) mode can be determined by the cationic chromatographic surface of the monolith. At acidic pH and high voltage across the column, the monolithic stationary phase provided conditions for predominantly capillary electrophoretic migration of peptides. At basic pH and electric field across the column, enhanced chromatographic retention of peptides on monolithic capillary column made CEC mechanisms of migration responsible for separation. The role of pressure, ionic strength, pH, and organic content of the mobile phase on chromatographic performance was investigated. High efficiencies (exceeding 300 000 plates/m) of the monolithic columns for peptide separations are shown using volatile and nonvolatile, acidic and basic buffers. Good reproducibility and robustness of isocratic and gradient elution pressure-assisted CEC/CE separations were achieved for both UV and ESI-MS detection. Manipulation of the electric field and gradient conditions allowed high-throughput analysis of complex peptide mixtures. A simple design of sheathless electrospray emitter provided effective and robust low dead volume interfacing of monolithic multimode columns with ESI-MS. Gradient elution pressure-assisted mixed-mode separation CE/CEC-ESI-MS mass fingerprinting and data-dependent pCE/pCEC-ESI-MS/MS analysis of a bovine serum albumin (BSA) tryptic digest in less than 5 min yielding high sequence coverage (73%) demonstrated the potential of the method.     

Effect of the nature of the carrier gas on the chromatographic characteristics of monolithic silica capillary columns

Chromatographing a model mixture of hydrocarbons with various carrier gases (helium, hydrogen, nitrogen, carbon dioxide, and nitrous oxide) was used to study the separation ability of monolithic silica capillary columns. It was revealed that the nature of the carrier gas strongly affects the retention time of the sorbates and the height equivalent to a theoretical plate (HETP) of the column, with the values of both these parameters decreasing in the series He > H₂ > N₂ > CO₂ ～ N₂O. This effect was found to be more pronounced for normal hydrocarbons than for their isomers. For chromatographing with CO₂ or N₂O under optimum conditions, the HETP was 25–30 μm, a value indicative of a higher specific efficiency of monolithic capillary columns. Theoretical correlations between the HETP and the properties of the mobile phase were considered. As a result, it was concluded that elevated pressures of the carrier gas, which are required to ensure the optimum operation of monolithic capillary columns, may affect the properties of the chromatographic system.     

Enantioseparation on cellulose dimethylphenylcarbamate-modified zirconia monolithic columns by reversed-phase capillary electrochromatography

This work reports the preparation of monolithic zirconia chiral columns for separation of enantiomeric compounds by capillary electrochromatography (CEC). Using sol–gel technology, a porous monolith having interconnected globular-like structure with through-pores is synthesized in the capillary column as a first step in the synthesis of monolithic zirconia chiral capillary columns. In the second step, the surface of the monolith is modified by coating with cellulose tris(3,5-dimethylphenylcarbamate) (CDMPC) as the chiral stationary phase to obtain a chiral column (CDMPCZM). The process of the preparation of the zirconia monolithic capillary column was investigated by varying the concentrations of the components of the sol solution including polyethylene glycol, water and acetic acid. CDMPCZM is mechanically stable and no bubble formation was detected with the applied current of up to 30 μA. The enantioseparation behavior of the CDMPCZM columns was investigated by separating a set of 10 representative chiral compounds by varying the applied voltage and pH and organic composition of the aqueous organic mobile phases.     

双苯基杂化整体柱的制备及毛细管电色谱性能研究

以苯基三乙氧基硅烷(PTES)和1,4-双三乙氧基硅基苯(BTEB)为反应单体,分别采用盐酸和十二胺为催化剂,通过两步酸碱催化的溶胶-凝胶法制备了新型双苯基杂化硅胶毛细管电色谱整体柱。分别采用扫描电镜、红外光谱和压汞法对材料的结构特性进行了表征。结果表明,所制备的材料具有特定的网络结构特征,孔径主要分布在3.4μm左右,材料的总孔容为3.5 cm3/g,比表面积为145 m2/g。新型整体柱能够很好地分离烷基取代苯、稠环芳烃、取代苯胺和硝基苯酚异构体。整体柱重复性实验表明,6种苯的同系物保留时间和容量因子的相对标准偏差分别小于0.61%和0.30%(n=8)。不同批次的整体柱的保留时间和容量因子的相对标准偏差分别小于7.2%和5.6%(n=3)。     

Developments in ion chromatography using monolithic columns

The focus of this review is on current status and on-going developments in ion chromatography (IC) using monolithic phases. The use and potential of both silica and polymeric monoliths in IC is discussed, with silica monoliths achieving efficiencies upwards of 10(5) plates/m for inorganic ions in a few minutes or less. Ion exchange capacity can be introduced onto the monolithic columns through the addition of ion interaction reagents to the eluent, coating of the monolith with ionic surfactants or polyelectrolyte latexes, and covalent bonding. The majority of the studies to date have used surfactant-coated columns, but the stability of surfactant coatings limits this approach. Applications of monolithic IC columns to the separation of inorganic anions and cations are tabulated. Finally, a discussion on the recent commercialization of monolithic IC columns and the use of monolithic phases for IC peripherals such as preconcentrator columns, microextractors and suppressors is presented.     

Recent Advances of Polymer Monolithic Columns Functionalized with Micro/Nanomaterials: Synthesis and Application

The field of separation science has recently witnessed an explosion of interest and progress in the design and study of porous polymer monolithic materials. Monolithic columns with their unique structure possess some exceptional characteristics, which make them an excellent tool in the hands of analytical chemists, not only for separation but also for sample pretreatment. As a new member of the polymer monolith family, the micro/nanomaterial-functionalized polymer monolith has attracted considerable attention due to its many distinct characteristics, such as high permeability and selectively tailored surface chemistries. It exhibits great potential in separation science and analytical sample preparation. This review summarizes and highlights recent major advances of the micro/nanomaterial-functionalized polymer monolith, focusing on design considerations and the application of separation and enrichment. A brief overview of the properties of polymer monolithic columns is included, and then specific attention is paid to discuss the methods of fabrication and application of the micro/nanomaterial-functionalized polymer monolith in separation, sample pretreatment and enrichment, and highly sensitive detection. Finally, future possible research directions and challenges in the field are discussed.     

Effect of a linear polymer on crosslinking heterophase copolymerization of maleic anhydride, styrene, and divinylbenzene

A polymeric porogene has been shown to promote the formation of a developed porous structure in network maleic anhydride-styrene-divinylbenzene copolymers synthesized through crosslinking free-radical alternating copolymerization in the presence of a solvating solvent (dioxane).     

Chemically modified chiral monolithic silica column prepared by a sol-gel process for enantiomeric separation by micro high-performance liquid chromatography

In this work a new type of chiral monolith silica column was developed for the chiral separation by micro high-performance liquid chromatography (micro-HPLC). The chiral monolith column with a continuous skeleton and a large through-pore structure was prepared inside a capillary of 100 microm I.D. by a sol-gel process, and chemically modified with chiral selectors, such as L-phenylalaninamide, L-alaninamide and L-prolinamide, on the surface of the monolithic silica column. Based on the principle of ligand exchange, these chiral monolithic columns were successfully used for the separation of dansyl amino acid enantiomers, as well as hydroxy acid enantiomers by micro-HPLC. The chromatographic conditions, the enantioselectivity and the performance of columns are discussed.     

The effect of the nature of the stationary phase on the gas chromatographic retention of sorbates in monolithic columns

Retention factors were measured on silica gel, ethylene glycol dimethacrylate, and divinylbenzene monolithic columns for five groups of sorbates with different polarities. The retention factors of sorbates did not correlate directly with the polarity of the stationary phase probably because of differences in inner surface areas of sorbates accessible to sorbates. For the ethylene glycol dimethacrylate and divinylbenzene monoliths, the “methylene” selectivity was approximately the same and appreciably higher than for the silica gel monolith when helium was used as a carrier gas and approximately the same for monoliths of all types when the carrier gas was CO₂. Original Russian Text ? V.E. Shiryaeva, A.A. Korolev, T.P. Popova, A.A. Kurganov, 2009, published in Zhurnal Fizicheskoi Khimii, 2009, Vol. 83, No. 7, pp. 1365–1369.     

Poly(divinylbenzene-alkyl methacrylate) monolithic stationary phases in capillary electrochromatography

In this study, a series of poly(divinylbenzene-alkyl methacrylate) monolithic stationary phases, which were prepared by single step in situ polymerization of divinylbenzene and various alkyl methacrylates (butyl-, octyl-, or lauryl-methacrylate), were developed as separation columns of benzophenone compounds for capillary electrochromatography (CEC). In addition to the presence of plenty of benzene moieties, the stationary phases contained long and flexible alkyl groups on the surface. With an increase in the molecular length of alkyl methacrylate, the polymeric monolith, which had higher hydrophobicity, effectively reduced the peak tailing of benzophenones, but a weaker retention was observed. The unusual phenomenon was likely due to the π–π interaction between the aromatic compound and the polymeric material. The usage of longer alkyl methacrylate as reaction monomer limited the retention of aromatic compounds on the stationary phase surface, thus the π–π interaction between them was possibly reduced. Consequently, the retention time of aromatic compounds was markedly decreased with an increase in carbon length of alkyl methacrylate that was carried on the polymeric monolith. Compared to previous reports on polystyrene-based columns in which the peak-tailing problem was reduced by decreasing the benzene moieties on the stationary phase, this study demonstrated that the undesirable retention (peak-tailing) could also be improved by the inclusion of long alkyl methacrylate to the polystyrene-based columns.     

Monolithic capillary columns based on pentaerythritol acrylates for molecular‐size‐based separations of synthetic polymers

Monolithic capillary columns based on pentaerythritol triacrylate and pentaerythritol tetraacrylate were synthesized using different compositions of polymerization mixtures and different polymerization conditions. The impact of porogen type and porogen/monomer ratio on the porosity of synthesized monoliths was investigated. Porogen type appears to be the main factor influencing the separating properties of the monolithic sorbent. Using optimal polymerization conditions (porogen type, porogen/monomer ratio, reaction temperature, time etc.) monoliths with a porous structure optimized for polymer separations can be obtained. The monolithic capillary columns containing porous sorbents with optimized porosity are capable of separating 10 to 12 polystyrene standards in one chromatographic run utilizing both size exclusion chromatography and hydrodynamic chromatography separation mechanisms.     

牛血清白蛋白修饰毛细管整体柱的制备及组氨酸对映体分离

以甲基丙烯酸缩水甘油酯为单体, 乙二醇二甲基丙烯酸酯为交联剂, 环己醇和正十二醇混合溶液为致孔剂, 在最佳聚合条件下, 以偶氮二异丁腈为引发剂, 制备了毛细管整体柱基质, 并且研究了单体、交联剂及致孔剂对整体柱基质孔结构及渗透性的影响; 使用Epoxy方法在基质表面键合BSA, 制得BSA修饰的毛细管整体柱. 将此毛细管整体柱应用于毛细管电色谱中, 成功地分离出了组氨酸对映体, 分离度良好.     

Evaluation of a methacrylate-bonded cyclodextrins as a monolithic chiral stationary phase for capillary electrochromatography (CEC)-UV and CEC coupled to mass spectrometry

Glycidyl methacrylate-bonded β-cyclodextrin (GMA-β-CD) is synthesized as a new chiral monomer by direct chemical bonding with GMA using a fast and simple alternative procedure. Next, rigid and homogenous monolithic columns were prepared by polymerization of GMA-β-CD monomer with ethylene dimethacrylate (EDMA), in the presence of commonly used porogens and a charged achiral monomer to form a versatile chiral monolith. This is the first report in which a preparation procedure for a methacrylate-bonded CD is introduced for chiral separations in CEC. The degree of substitution of GMA-β-CD monomer and mobile-phase parameters were optimized to achieve the highest enantioselectivity and plate number. To evaluate the GMA-β-CD monolithic column, different classes of chiral compounds were screened. Under the optimized β-CD monolith phase and the optimum mobile-phase conditions, 30 neutral and basic chiral compounds and two acidic compounds could be separated. The high chemical and mechanical stability, homogenous microflow and no loss of material at the interface allows for the first time the feasibility of applying this polymer-based monolithic column for CEC coupled to ESI-MS. Compared with CEC-UV, CEC-ESI-MS showed higher sensitivity and lower resolution. However, resolution greater than 1.0 can still be obtained for majority of the select tested compound in CEC-ESI-MS with at least three out of seven compound providing Rs≥1.5. The results reinforce the potential of GMA-β-CD monolithic columns for chiral separations with high sensitivity in CEC-ESI-MS. Finally, using hexobarbital as the model chiral analyte, the monolithic column demonstrated excellent stability and reproducibility of retention time and enantioselectivity.     

Repeatability in column preparation of a reversed-phase C18 monolith and its application to separation of tocopherol homologues

This work investigated the repeatability of column preparation for a reversed-phase C18 monolith, namely stearyl methacrylate-co-ethylene glycol dimethacrylate (SMA-EDMA). The columns were thermally polymerised using three commonly available heating devices (GC oven, hot air oven and water bath) and their chromatographic performance evaluated using micro-liquid chromatography for separation of five test compounds. Precision in terms of %RSD of retention times were 9.0, 6.5, and 12.5 using GC oven, hot air oven and water bath, respectively. Between-batch precision for the hot air oven (n = 3 days) was less than 10.4% for retention time. The SMA-EDMA monolith was applied to the separation of tocopherol homologues by capillary electrochromatography. Usually tocopherol homologues cannot be completely separated by conventional reversed-phase C8- or C18-packed bed or C18-silica based monolithic columns. Polymer monolith has been shown to give remarkable selectivity towards the tocopherols compared to the conventional microparticulate phase and silica based monolith. Successful separation of the tocopherol isomers was achieved on the SMA-EDMA monolith without any column modification.