A new method for the quantitative analysis of organochlorine pesticides and polychlorinated biphenyls

A simple method is described for the quantitative determination of organochlorine pesticides and polychlorinated biphenyls (PCB's) in water at the sub-ppb level. A micro gas-phase extractor advantageously replaces other preconcentration and purification techniques. The extract is analyzed by capillary gas chromatography without further enrichment. The recovery at the ppb level was nearly 100% for organochlorine pesticides and more than 80% for PCB's. The complete procedure including sample preparation, steam distillation-extraction, and capillary gas chromatographic analysis is carried out in less than four hours.     

Determination of 3-phenyl-4-hydroxy-6-chloropyridazine in groundwater using enrichment on porous organic polymers

Summary A method is described for the determination of 3-phenyl-4-hydroxy-6-chloropyridazine in potable water. The method is based on isolation and enrichment by passing the water sample through a column of macroreticular polymeric adsorbent resin, concentration, derivatisation with pentafluorobenzoyl chloride and GC measurement with a N-specific detector. The individual experiments for establishing the working conditions, especially the adsorption characteristics of different types of resin, are described. The highest enrichment efficiency is obtained with the methacrylate-type resin XAD7. In field-sampling experiments a 10cm column yields 57% recovery at 100mLmin^–1 flow rate, 0.3 ppb concentration level and 1 L sample volume. The method is completely documented; performance data are a detection limit of 0.07 g L^–1 and a mean recovery of 75% at the 0.3 ppb level.     

The efficiency of cellix-p for the preconcentration of lead and other trace metals from waters

The cheating ion-exchanger Cellex-P, a cellulose phosphate ester, is shown to be effective for the preconcentration of Cu, Ni, Mn, Cd, Zn and Pb from water. The pH of the sample is not critical within the approximate range 5–8. The collected ions can be eluted efficiently in 10–25 ml of 1 M nitric acid from 2–16.5-cm columns of resin. Common salts present in natural waters do not interfere. Cellex-P is used for the preconcentration and determination of the metal ions in potable water by graphite-furnace atomic absorption spectrometry.     

Stereoselective analysis of acid herbicides in natural waters by capillary electrophoresis.

A capillary electrophoretic method for the stereoselective analysis of aryloxypropionic and aryloxyphenoxypropionic acidic herbicides in ground water and river water was performed. Vancomycin and gamma-cyclodextrin were added to the background electrolyte (BGE) as chiral selectors. Water sample preconcentration was accomplished by solid-phase extraction on styrene-divinylbenzene packed cartridges (2 L of ground water and 1 L of river water). The analytical method allowed for the resolution of mecoprop, fenoprop, fluazifop and haloxyfop racemic mixtures in natural water samples spiked with enantiomer concentration levels in the range 0.1-0.13 ppb for ground water and 0.4-0.54 ppb for river water.     

On-line pre-concentration of atrazine by antibody immobilization capillary electrophoresis

Antibody coupled capillary electrophoresis was employed in the pre-concentration and detection of atrazine at the parts per billion (ppb) level. A 1000-fold increase in detection has been demonstrated in the use of IgG anti-atrazine monoclonal antibodies for the analysis of atrazine in well water by capillary zone electrophoresis (CZE) with UV-VIS detection. These results were confirmed by an enzyme linked immunosorbent assay (ELISA) specific for atrazine.     

Direct measurement of part-per-billion levels of dimethyl sulfoxide in water by gas chromatography with stacked injection and chemiluminescence detection

Dimethyl sulfoxide (DMSO) is a chemical of industrial significance with many important applications. DMSO is used as an industrial solvent, in drug delivery and healthcare applications, among others. Analysis of DMSO in water typically involves extensive sample preparation, enrichment, and derivatization to improve solute detectability. A novel gas chromatographic procedure has been developed for the direct measurement of trace levels of DMSO in an aqueous matrix, such as potable water. The technology utilizes stacked injection techniques for in-column solute enrichment, a precolumn to enhance solute focusing effects, and sulfur chemiluminescence detection for matrix suppression and sensitivity. A detection limit of 2 parts per billion (ppb) (v/v) of DMSO in water was attained. Relative precision of less than 7% at the concentration of 10 ppb (v/v) of DMSO was demonstrated. A correlation coefficient of 0.9988 was obtained over a range of 2 ppb (v/v) to 100 ppb (v/v). No detectable carry-over was found at the 5 ppb (v/v) level whereas less than 4% carry-over was observed at the 100 ppb (v/v) level. Various sample storage media including glass, polyethylene, and polycarbonate were also studied to minimize solute loss. Recoveries greater than 84% were achieved with all storage media tested. The method was found to be reliable and simple to implement.     

On-line solid phase extraction system using PTFE packed column for the flame atomic absorption spectrometric determination of copper in water samples

A new flow injection on-line adsorption preconcentration system adapted to flame atomic absorption spectrometry (FAAS) for copper determination at the mug l(-1) level was developed. Polytetrafluoroethylene (PTFE) turnings packed in a mini-column were used as sorbent material. The copper ammonium pyrrolidine dithiocarbamate (APDC) complex was sorbed on the PTFE turnings, from which it could be eluted on-line instantly by isobutyl methyl ketone (IBMK) into the flame at a flow rate of 2.3 ml min(-1). The system was optimized and offered good performance characteristics with practically unlimited life time, greater flow rates and improved flexibility, as compared with other sorbent materials and the knotted reactor preconcentration systems. With 1 min preconcentration time, and a sample frequency of 40 h(-1), the enhancement factor was 340, which could be further improved by increasing the preconcentration time. The detection limit was c(L)=0.05 mug l(-1), and the precision was 1.5%, at the 2.0 mug l(-1) Cu level. The method has been applied successfully to the analysis of potable, river and seawater, and its accuracy was tested by the analysis of certified reference materials and by recovery measurements on spiked samples. No significant interferences exist from other substances usually occurring in natural water.     

Use of chelating resins and inductively coupled plasma mass spectrometry for simultaneous determination of trace and major elements in small volumes of saline water samples

For some saline environments (e.g. deeply percolating groundwater, interstitial water in marine sediments, water sample collected after several steps of fractionation) the volume of water sample available is limited. A technique is presented which enables simultaneous determination of major and trace elements after preconcentration of only 60 mL sample on chelating resins. Chelex-100 and Chelamine were used for the preconcentration of trace elements (Cd, Cu, Pb, Zn, Sc) and rare earth elements (La, Ce, Nd, Yb) from saline water before their measurement by inductively coupled plasma mass spectrometry. Retention of the major elements (Na, Ca, Mg) by the Chelamine resin was lower than by Chelex; this enabled their direct measurement in the solution after passage through the resin column. For trace metal recoveries both resins yield the same mass balance. Only Chelex resin enabled the quantitative recovery of rare earth elements. The major elements, trace metals and rare earth elements cannot be measured after passage through one resin only. The protocol proposes the initial use of Chelamine for measurement of trace and major elements and then passage the same sample through the Chelex resin for determination of the rare earth elements. The detection limit ranged from 1 to 12 pg mL^–1. At concentrations of 1 ng mL^–1 of trace metals and REE spiked in coastal water the precision for 10 replicates was in the range of 0.3–3.4% (RSD). The accuracy of the method was demonstrated by analyzing two standard reference waters, SLRS-3 and CASS-3.     

Determination of absorption efficiencies of carbon dioxide absorbents by gas chromatography

An HP-5880A gas chromatograph equipped with FID has been used to determine the efficiency of various CO(2) absorbents and some molecular sieves. Temperature, the CO(2) concentration in the absorbed gas mixture and space velocity of the gas mixture have effects on the absorption efficiency to different degrees, but temperature is a controlling factor. It has been established that in gas analysis the systematic errors arising from CO(2) impurities in the carrier gas are negligible when CO(2) is absorbed by carbon dioxide absorbents. Three methods for eliminating blank error are presented. The differential volume method through preconcentrating at the same time but at different flow-rates (DVMST) is proposed as the best method in preconcentration analysis. With the preconcentration technique, the minimum detectable level for CO(2) in a 10-litre sample is around 0.3 ppb(v/v).     

Use of chelating resins and inductively coupled plasma mass spectrometry for simultaneous determination of trace and major elements in small volumes of saline water samples

For some saline environments (e.g. deeply percolating groundwater, interstitial water in marine sediments, water sample collected after several steps of fractionation) the volume of water sample available is limited. A technique is presented which enables simultaneous determination of major and trace elements after preconcentration of only 60 mL sample on chelating resins. Chelex-100 and Chelamine were used for the preconcentration of trace elements (Cd, Cu, Pb, Zn, Sc) and rare earth elements (La, Ce, Nd, Yb) from saline water before their measurement by inductively coupled plasma mass spectrometry. Retention of the major elements (Na, Ca, Mg) by the Chelamine resin was lower than by Chelex; this enabled their direct measurement in the solution after passage through the resin column. For trace metal recoveries both resins yield the same mass balance. Only Chelex resin enabled the quantitative recovery of rare earth elements. The major elements, trace metals and rare earth elements cannot be measured after passage through one resin only. The protocol proposes the initial use of Chelamine for measurement of trace and major elements and then passage the same sample through the Chelex resin for determination of the rare earth elements. The detection limit ranged from 1 to 12 pg mL(-1). At concentrations of 1 ng mL(-1) of trace metals and REE spiked in coastal water the precision for 10 replicates was in the range of 0.3-3.4% (RSD). The accuracy of the method was demonstrated by analyzing two standard reference waters, SLRS-3 and CASS-3.     

Solid-phase extraction and sample stacking-micellar electrokinetic capillary chromatography for the determination of multiresidues of herbicides and metabolites

Micellar electrokinetic capillary chromatography (MEKC) with diode array detection was used for the separation of 13 compounds (eight herbicides widely used in agriculture: metribuzin, lenacil, ethofumesate, atrazine, terbutryn, isoproturon, chlorotoluron and linuron, and five of their principal degradation products; namely, deethylatrazine, 2-hydroxyatrazine, deethyl-2-hydroxyatrazine, deisopropylatrazine and 3-chloro-4-methylphenylurea). Peak separation for the 13 analytes was not successful when a single surfactant system was employed, neither sodium dodecyl sulfate (SDS) nor dioctyl sulfosuccinate (DOSS) sodium salt. However, a mixture of these herbicides was successfully separated using a mixed micellar system involving SDS–DOSS in less than 14 min. An application study of an on-line concentration technique for MEKC was carried out to enhance sensitivity. The optimized on-line stacking procedure consisted simply of the addition of 50 mM of sodium chloride to the injection sample, the stacking effect being more intensive as analyte polarity increased. When this stacking procedure was combined with an off-line sample preconcentration step, based on solid-phase extraction, analytes could be detected in the ppb range. The whole method was applied to ultra-high-quality and natural waters. Linear relationships between the analytical signal and the initial analyte concentration were found to be independent of the type of water, except for the more polar analytes for which small differences were observed.     

Extraction,separation, and fluorometric analysis of selected environmental contaminants

Teratogenic, carcinogenic, and pervasive endocrine disrupting compounds (EDCs) in suspect water systems present an immediate threat to both the environment and potable water supplies. The US Environmental Protection Agency mandated research regarding suspect EDCs, personal care products, and pesticide pollution requires the use of suitable methods of analysis that can perform extraordinarily well in the field and show low “cost to benefit” ratios. Such methods must increasingly address the need for enhanced sensitivity and selectivity in interrogating complex mixtures. Here, several device and method optimization strategies, specific for these classes of compounds, are discussed and include, among others, the preconcentration of field samples utilizing high performance extraction disk cartridges. Matrix interferences and undetectable concentration levels are eliminated by the way of an RP extraction technique that is vital to obtaining detectable concentrations of target analytes in the ppb range. Established capillary EKC methods are modified and implemented on a short capillary for low nanoliter discrete injections, efficient separations, and detection with LIF of analyte mixtures. Efficient separations were achieved with plate counts ranging from 10³ to 10⁴. Analytes spiked into real sample matrices at ppb levels were easily separated and detected via LIF using a He/Cd laser operating at 325 nm. The presented techniques are valuable in determining both the presence and concentration of suspect contaminates in different water systems. The methods presented here could easily be extended to microfluidic platforms with little to no optimization for on‐site testing.     

New strategy for the biosorption of atrazine after magnetic solid‐phase extraction from water followed by high‐performance liquid chromatography analysis

We describe a rapid and simple microextraction of atrazine from water samples. This method is based on the use of magnetic nanoparticles as sorbents and bioaggregates that are applied to the extraction and preconcentration of atrazine. The resulting magnetic nanoparticles possess a fast adsorption kinetics and high adsorption capacity. Bioaggregates made up of rhaminolipid biosurfactant were assessed as a new strategy for the sample treatment. The extractant was obtained from magnetic nanoparticles using the magnetic solid‐phase extraction method. Then the target analyte was rapidly transferred from the sorbent surface to bioaggregates, which have a low toxicity and are green and ecofriendly. Finally, the extract is centrifuged and transferred to micro‐syringe for analysis by high‐performance liquid chromatography. Experimental parameters affecting the extraction efficiency were studied and optimized. Under optimum conditions the enrichment factor was 268. The linear dynamic range and limit of detection were 0.1–50 and 0.033 μg/L, respectively. The relative standard deviation for six replicate measurements was 5.3%. The results demonstrate good applicability of biosorption‐assisted magnetic solid‐phase extraction method for the determination of atrazine from water samples.     

Synthesis of cross-linked chitosan modified with the glycine moiety for the collection/concentration of bismuth in aquatic samples for ICP-MS determination.

A chelating resin, cross-linked chitosan modified with the glycine moiety (glycine-type chitosan resin), was developed for the collection and concentration of bismuth in aquatic samples for ICP-MS measurements. The adsorption behavior of bismuth and 55 elements on glycine-type chitosan resin was systematically examined by passing a sample solution containing 56 elements through a mini-column packed with the resin (wet volume; 1 ml). After eluting the elements adsorbed on the resin with nitric acid, the eluates were measured by ICP-MS. The glycine-type chitosan resin could adsorb several cations by a chelating mechanism and several oxoanions by an anion-exchange mechanism. Especially, the resin could adsorb almost 100% Bi(III) over a wide pH region from pH 2 to 6. Bismuth could be strongly adsorbed at pH 3, and eluted quantitatively with 10 ml of 3 M nitric acid. A column pretreatment method with the glycine-type chitosan resin was used prior to removal of high concentrations of matrices in a seawater sample and the preconcentration of trace bismuth in river water samples for ICP-MS measurements. The column pretreatment method was also applied to the determination of bismuth in real samples by ICP-MS. The LOD of bismuth was 0.1 pg ml(-1) by 10-fold column preconcentration for ICP-MS measurements. The analytical results for bismuth in sea and river water samples by ICP-MS were 22.9 +/- 0.5 pg ml(-1) (RSD, 2.2%) and 2.08 +/- 0.05 pg ml(-1) (RSD, 2.4%), respectively.     

Large volume sample stacking of cationic tetracycline antibiotics toward 10 ppb level analysis by capillary electrophoresis with UV detection

This paper aimed to build up a sensitive CE method for the analysis of tetracyclines (TCs) antibiotics (including tetracycline, chlorotetracycline, oxytetracycline, and doxycycline) with conventional UV detection. Here, the large volume sample stacking was applied to achieve in capillary preconcentration of the targets. To achieve large volume sample stacking, the essential step was a large volume of sample (around 83.3% of total capillary length from inlet to detection window) hydrodynamically loaded. Then, the reserved voltage was added in order to push the sample matrix out of the capillary. Due to different pH between sample solution (pH 4.6) and BGE (pH 11.0), the cationic TCs would turn into negatively charged while the sample matrix was removing from the capillary. Finally, the anionic TCs were stacked at the inlet for the subsequent separation. Although the loss of sample existed during their charge transformation, the LODs could be improved around 40 times than that obtained by normal hydrodynamic injection CE method. Here, the LODs were in the range of 8.1–14.5 μg/L, around 10 ppb that close to the level by electrochemiluminescence or laser‐induced fluorescence detection of TCs by CE. The precision was characterized by RSDs of migration times and peak areas, which were in the range of 0.19–0.24% and 0.97–2.54%, respectively. The recoveries of the developed method were in the range of 95–112% by spiking TCs in the tap water. The proposed inline preconcentration CE method could be a simple, speed, and sensitive method for the quantitative analysis of TCs.     

Dynamic pH junction-sweeping capillary electrophoresis for online preconcentration of toxic pyrrolizidine alkaloids in Chinese herbal medicine

There is a need to develop simple yet effective preconcentration methods to enhance concentration sensitivity for CE analysis of trace level analytes in real samples, particularly when commonly available but less sensitive detection methods, e.g., UV detection, are used. In this report, a hyphenated online preconcentration strategy combining dynamic pH junction with sweeping (i.e., dynamic pH junction-sweeping) was employed for the analysis of four toxic pyrrolizidine alkaloids (PAs) of senkirkine, senecionine, retrorsine, and seneciphylline in Chinese herbal medicine (Kuan donghua). Direct electrokinetically focusing of a large sample volume injection (up to 20% of capillary length) on the capillary was performed using the dynamic pH junction-sweeping method. A sample matrix consisting of 10 mM phosphate with 20% methanol at pH 4.0 and a BGE containing 20 mM borate, 30 mM SDS, and 20% methanol at pH 9.1 were utilized to realize dynamic pH junction-sweeping for PAs. This online preconcentration strategy resulted in sensitivity enhancement factors ranging from 23.8- to 90.0-fold for the four toxic PAs, giving an LOD as low as 30 ppb for the PAs. Critical factors such as sample matrix type, pH, and salt concentration were also examined to achieve higher sensitivity enhancement, shorter analysis time, and better resolution. The results indicate that the proposed dynamic pH junction-sweeping technique is a powerful alternative approach for identification and determination of trace levels of these toxic PAs and other hydrophobic, protonatable compounds in real samples.     

A multi-syringe flow injection system for the spectrophotometric determination of trace levels of iron in waters using a liquid waveguide capillary cell and different chelating resins and reaction chemistries

A method integrating a long waveguide capillary cell with a preconcentration resin in a multi-syringe flow injection analysis (MSFIA) system for iron determination in waters was developed. The determination of iron is based on a colorimetric reaction and two reagents were tested, ferrozine and ammonium thiocyanate. A liquid waveguide capillary cell (1.0 m pathlength, 550 µm i.d. and 250 µL internal volume) with a preconcentration resin were used to improve the sensitivity of the determination. Two different preconcentration resins were also tested, Chelex 100 and NTA Superflow. The developed method employing the NTA Superflow with ferrozine colorimetric reagent provided a detection limit of 0.05 µg L^− 1 with a linear response up to 8 µg L^− 1 and a sample throughput rate of 12 per hour. The developed system presents low reagents/sample consumptions. The accuracy was assessed using a certified reference water sample.     

Preconcentration of trace chalcophile elements by a zincon--loaded resin and its application to neutron activation analysis (author's transl)]

A chelating agent-loaded resin consisting of an anion exchange resin and zincon which has widely been employed as a specific reagent for zinc(II) and copper(II) in spectrophotometry was prepared. The adsorption behavior of some chalcophile elements was studied in detail, with respect to pH, flow rate and exchange capacity. From the results, it was confirmed that the zincon-loaded resin reacts selectively with copper(II), zinc(II), mercury(II) and lead(II) at lower pH region, and the above reaction is stoichiometric as in the case of the reaction of zincon with metal ions in aqueous solution. Furthermore, the zincon-loaded resin was applied to the selective concentration of trace amounts of chalcophile elements in natural water samples prior to neutron activation analysis. Water samples taken from the Watarase River were filtered and the pH of each filtrate was adjusted to ca. 5.5. After preconcentration was made by the column method (zincon-loaded resin: 2 x 10-4 mol/g resin, 1.0 g, 7 mm phi x 35 mm), the resin in the column was washed and dried in a desiccator. The standard material was also prepared according to the above mentioned scheme. The sample and the standard materials packed in polyethylene vials were irradiated for 40 min by a neutron flux of 5 x 10(13 n.cm-2.sec-1 in the JRR-4 of the Japan Atomic Energy Research Institute. After cooling the materials, activity measurements were made. The results were 53 ppb for copper, 0.25 ppb for mercury.     

Combination of large volume sample stacking and dynamic pH junction for on-line preconcentration of weak electrolytes by capillary electrophoresis in comparison with isotachophoretic techniques

An on-line preconcentration capillary electrophoresis (CE) technique, which combines a large volume sample stacking with a dynamic pH junction technique, is introduced in this paper. This dynamic pH junction with co-electroosmotic migration is formed between sodium borate pH 9.5 and sodium phosphate pH 2.5 with 150 mM sodium dodecylsulfate (SDS). A full capillary based injection allows determination of weak acidic compounds at ppb concentration levels (achieved LOD for benzoic acid was 11 nmol L(-1)). The proposed preconcentration method was compared with ITP/ITP (LOD 120 nmol L(-1)), ITP/CZE (LOD 740 nmol L(-1)) and a simple CZE method (LOD 23,330 nmol L(-1)). The analytical potential of this method was assessed with juice test samples.     

Separation and preconcentration of trace manganese from various samples with Amberlyst 36 column and determination by flame atomic absorption spectrometry

This work assesses the potential of a new adsorptive material, Amberlyst 36, for the separation and preconcentration of trace manganese(II) from various media. It is based on the sorption of manganese(II) ions onto a column filled with Amberlyst 36 cation exchange resin, followed by the elution with 5 mL of 3 mol/L nitric acid and determination by flame atomic absorption spectrometry (FAAS) without interference of the matrix. Different factors including pH of sample solution, sample volume, amount of resin, flow rate of sample solution, volume and concentration of eluent, and matrix effects for preconcentration were investigated. Good relative standard deviation (3%) and high recovery (>95%) at 100 μg/L and high enrichment factor (200) and low analytical detection limit (0.245 μg/L) were obtained. The adsorption equilibrium was described well by the Langmuir isotherm model with maximum adsorption capacity of 88 mg/g of manganese on the resin. The method was applied for the manganese determination by FAAS in tap water, commercial natural drinking water, commercial treated drinking water and commercial tea bag sample. The accuracy of the method is confirmed by analyzing the certified reference material (tea leaves GBW 07605). The results demonstrated good agreement with the certified values.