Adsorption from ternary liquid mixtures on silica gel and aluminium oxide

Formation of mixed adsorbed layers was tested for ternary liquid mixtures containing methanol or acetone and the binary solvent benzene+n — heptane. The specific excess adsorption isotherms from the liquid phase were measured on silica gel, silanized silica gel and aluminium oxide. The experimental adsorption data are discussed on the basis of the changes in the mixed solvent composition.     

Conformation of polyesters adsorbed on solid surfaces

The conformation of a polyester, poly(ethylene o-phthalate), of relatively low molecular weight was studied after adsorption. The extension of the adsorbed molecule in a poor solvent on several planar metal surfaces was studied by ellipsometry and the fraction p of attached groups on colloidal silica particles in a good solvent was determined by the shift in the infrared absorption frequency between free and adsorbed carbonyl groups. In contrast to previously reported results for polystyrene, the extension normal to the surface remained constant (～70 A.) while the concentration of polymer in the adsorbed film increased during the adsorption period. The value of p (0.34 for MW = 5400) is relatively high and was independent of surface population for the range of solution concentrations measured. Differences between these results and those for polystyrene are interpreted as resulting from differences in interaction energy and chain stiffness.     

Self-immobilization of poly(methyloctylsiloxane) on high-performance liquid chromatographic silica

Poly(methyloctylsiloxane) (PMOS) was deposited on HPLC silica by a solvent evaporation procedure and this material was then extracted, using a good solvent for the PMOS, after different time periods, to remove unretained liquid polymer. Solvent extraction data reveal changes which occur at ambient temperature as a function of the time interval between particle loading and extraction. The quantity of PMOS remaining on the silica after extraction, as determined by elemental analysis for carbon, is attributed to strongly adsorbed polymer. This phenomenon is termed self-immobilization. Solid-state 29Si NMR spectra indicate the formation of a silicon species with a different chemical shift than the original PMOS. These new signals are attributed to a combination of different adsorbed and chemically bonded groups.     

Perchloric Acid Supported on Silica Catalyzed Efficient Synthesis of 1,5‐Benzodiazepines

Perchloric acid adsorbed on silica gel efficiently catalyzed the condensation of o‐phenylenediamines (OPDA) with cyclic and acyclic ketones at ambient temperature to afford 1,5‐benzodiazepines in good yields under solvent‐free conditions.     

Electron spin resonance studies of spin-labelled polymers—18: Adsorption of spin-labelled poly(vinyl acetate) on silica surfaces

The adsorption of spin-labelled poly(vinyl acetate) from dilute solutions in ethyl acetate, chloroform and toluene onto three silica adsorbents of different surface silanol contents was studied. The adsorption capacities of the three silica samples, which decreased with decreasing surface silanol content, were dependent on the nature of the solvent, being greatest in the poor solvent toluene and least in the good solvent ethyl acetate. The ESR spectra of the polymer adsorbed on the silica of highest silanol content suggested that the polymer had a relatively flat conformation when toluene or chloroform was solvent and a more looped conformation when ethyl acetate was solvent. With the silica of intermediate silanol content, the polymer adsorbed from chloroform solution also had a loopy conformation. The silica of lowest silanol content was prepared by treating the first silica absorbent with trimethylchlorosilane. The line-shapes in the ESR spectrum of the labelled polymer adsorbed on this modified silica indicated a change in mode of adsorption.     

Spectrometry: Speciation of Parts PER Billion of Metal Ions Using Silica and C18-Bonded Silica Columns and Graphite Furnace Atomic Absorption Spectrometry

Abstract

It is demonstrated that silica gel columns will quantitatively adsorb free Cu²⁺ and Pb²⁺ ions at pH > 8. These are eluted with 0.1 M HNO₃ but not with methanol. Negatively charged EDTA chelates are not adsorbed. Neutral APDC chelates are partially adsorbed on silica columns, but are quantitatively adsorbed on C18-bonded columns, and are eluted with methanol. The metal ions are partially adsorbed on C18-bonded columns, due to residual silanol groups. A microcolumn (1 mm i.d., 5 cm length) manifold system is described for automatic delivery of eluant (0.12 ml) to a heated atomic absorption graphite atomizer, using either methanol or 0.1 M HNO₃ in methanol eluant, allowing speciation and measurement of parts per billion of metals. These studies demonstrate that by using a mixed column or sequential columns of silica gel and C18-bonded silica, cationic and neutral metal species could be adsorbed, followed by sequential elution and measurement using methanol and then 0.1 M HNO. Negatively charged species could be measured directly in the sample eluant or obtained by difference from a total metal measurement.     

A Novel Low Solvent Method for Grafting Polyaniline to Silylated Silica

Summary: Silica gel, an important inorganic polymer with many applications, was silylated with 3-(phenylaminopropyl)trimethoxysilane (PAPTMOS) by means of a novel “low solvent” method, whereby the silane was dissolved in a small amount of methanol, mixed with silica and reaction carried out in a heated vacuum oven. Polyaniline (PANI) was grafted to the silylated silica by in situ polymerization of aniline, then dedoped with aqueous ammonia. Physically adsorbed PANI was removed from the modified silica by washing with tetrahydrofuran (THF) and N-methyl-2-pyrrolidone (NMP). The silylated, PANI-modified silica had electrical conductivity 1.2 × 10⁻³ S cm⁻¹ after being re-doped with methanesulfonic acid. FTIR, elemental analysis, X-ray photoelectron spectroscopy, solid-state ¹³C and ²⁹Si NMR and morphological studies by SEM confirmed successful formation of the SiO₂-polyaniline hybrid material.     

硅胶自溶液中吸附胆固醇和卵磷脂

卵磷脂和胆固醇是细胞膜的主要组成,它们在不同界面上的定向排列方式对细胞膜的结构与功能起着重要的作用。用固体物质自非水溶剂中吸附类脂化合物形成类脂单层,再自水溶液中吸附蛋白质,可制成固体载体上的模拟生物膜。在固体表面上的类脂单层膜中类脂分子的定向方式与溶剂和固体表面性质有关。这些研究大多数是以非孔性物质为吸附剂(如aerosil,石墨化炭黑,carbochrom.等)自有机溶剂中吸附类脂化合物(主要是胆固醇和卵磷脂),根据单层饱和吸附时分子占据的面积推算单层中类脂化合物分子的取向。实际应用的吸附剂大多是孔性的,因此研究类脂化合物在孔性吸附剂(如,硅胶、活性炭等)上的吸附机理更有实际意义。     

Solvatochromic studies on the hydrogen-bond donating and dipolarity/polarizability properties of the polyethylene oxide/silica interface

The polarity of the polyethylene oxide(PEO)/silica interface in 1,2-dichloroethane as solvent is classified by means of linear solvation energy (LSE) relationships . The properties of the bare silica particle surface and the silica/PEO interface is expressed by two terms: the dipolarity/polarizability (π*) of the interface and the hydrogen-bond donating ability (α) of the surface silanols. These terms can be defined by using the Kamlet–Taft solvent parameters α and π* as a reference system. The interfacial polarity parameters α and π* were calculated by means of correlation analyses of the energy of the UV/vis absorption maxima of the surface polarity indicators: di-cyano-bis(1,10-phenanthroline) iron II, bis-4,4′-(N,N-dimethylamino) benzophenone, and 2,6-diphenyl-4-(2,4,6-triphenyl-N-pyridino)phenolate when adsorbed onto the PEO/silica particle surface. The experimental values of the E _T(30) parameter of the PEO/silica interface are compared with independently calculated values employing specific LSE relations derived for well-behaved regular solvents and functionalized silicas. PEO adsorption on silica causes a decrease in the value of the α parameter of the silica surface and an evident increase in the dipolarity/polarizability of the interface. Received: 16 December 1998 Accepted in revised form: 8 January 1999     

Application of a monolithic silica capillary adsorbent for the preconcentration of airborne trichloroethylene and tetrachloroethylene

Monolithic silica with a bimodal pore structure was prepared in a fused silica capillary by the sol-gel process and investigated as an adsorbent for the preconcentration of airborne trichloroethylene and tetrachloroethylene. The airborne trichloroethylene and tetrachloroethylene are adsorbed when they flow through the silica capillary column and can be desorbed by liquid hexane followed by GC/MS analysis. The monolithic silica adsorbent is mechanically stable and no frits or other special structures are needed to retain them in place. In addition, owing to the smaller size of the capillary column, only a small volume of desorption solvent is needed. The present investigation demonstrates the satisfactory applicability of monolithic silica as a capillary adsorbent.     

Adsorption of polar substances from binary and ternary mixtures on silica gel

The adsorption isotherms of acetone and methyl ethyl ketone from binary and ternary mixtures in benzene and n-heptane on silica gel were measured. The experimental adsorption data are discussed on the basis of changes of the composition of mixed solvent (benzene + n-heptane) in ternary mixtures. It has been found that the different structures of the surface phase correspond to the system investigated. The marked dependence of the adsorption on the solvent character is demonstrated. For benzene and ternary (ketone + benzene + n-heptane) mixtures a mixed character of the surface phase is observed whose composition is determined by competition of liquid components for silica surface as well as its tendency to complex. Bilayer model of the surface phase gives a good representation of the experimental data for binary systems benzene + ketone.     

Oleophilic ion-exchange resins. IV. Swelling of quaternary ammonium polymers in mixed solvents

The swelling characteristics of an oleophilic anion-exchange resin in methanol–benzene and ethanol–chloroform mixed solvent systems were compared with those of a conventional anion-exchange resin. The oleophilic resin was prepared by amination of chloromethylated polystyrene 1% DVB with N,N-dimethyldodecylamine. It showed a large shift of the swelling peak from polar to less polar solution compositions in both methanol–benzene and ethanol–chloroform systems as compared with the swelling of conventional resins. Total solvent uptake and solvent distribution between resin and solvent phases were also determined. The less polar solvent (benzene or chloroform) was sorbed preferentially by the oleophilic resin over a wide range of composition, while preference for the more polar solvent (methanol or ethanol) by the conventional resin was shown over the entire composition of the mixed solvent systems. The Newman-Krigbaum treatment of mixed solvents was applied to swelling data on the ethanol–chloroform–oleophilic resin system, where the volume of the gel network plus the solvent imbibed was relatively constant over the entire range of composition. The result suggests a strong similarity of the liquid–liquid interaction terms in this gel phase compared with those in the pure binary liquid phase.     

Hydrogen-bonding molecular ruler surfactants as probes of specific solvation at liquid/liquid interfaces

Resonance-enhanced, second harmonic generation (SHG) is used to measure the electronic structure of solutes sensitive to specific solvation adsorbed to liquid/liquid and liquid/solid interfaces. Here, specific solvation refers to solvent–solute interactions that are directional and localized. N-methyl-p-methoxyaniline (NMMA) is a solute whose first allowed electronic transition wavelength remains almost constant (∼315 nm) in non-hydrogen-bonding solvents regardless of solvent polarity. However, in hydrogen-bond-accepting solvents such as dimethylsulfoxide, NMMA’s absorbance shifts to longer wavelengths (320 nm), whereas in hydrogen-bond-donating solvents (e.g., water), the absorbance shifts to shorter wavelengths (∼300 nm). SHG experiments show that at alkane/silica interfaces, surface silanol groups serve as moderately strong hydrogen-bond donors as evidenced by NMMA’s absorbance of 307 nm. At the carbon tetrachloride/water interface, NMMA absorbance also shifts to slightly shorter wavelengths (298 nm) implying that water molecules at this liquid/liquid interface are donating strong hydrogen bonds to the adsorbed NMMA solutes. In contrast, experiments using newly developed molecular ruler surfactants with NMMA as a model hydrophobic solute and a hydrophilic, cationic headgroup imply that, as NMMA migrates across an aqueous/alkane interface, it carries with it water that functions as a hydrogen-bond-accepting partner.     

High-performance liquid chromatography on dynamically modified silica : II. Modification of various silica packings with cetyltrimethylammonium bromide

High-performance liquid chromatography on silica using eluents containing cetyltrimethylammonium (CTMA) bromide was investigated, and adsorption isotherms were determined for two silica packings of different pore diameter and surface area. It was found that about one CTMA ion was adsorbed per square nanometer of the silica surface at pH 7.5 and at a concentration of 6 mM CTMA bromide in 50% of methanol.Fourteen different silica packings were compared using a test mixture, and thirteen were found to exhibit the same selectivity towards the test mixture, which included acids, bases and non-ionic compounds, thus providing a chromatographic system that is largely independent of the origin of the column material.The retention mechanisms for the five test compounds are discussed.     

Solid phase versus solvent extraction of pesticides from water

The average recovery for 12 pesticides spiked into 100 ml of water at 0.1 ppb was 90% when cartridges containing 100 mg of C-18 bonded porous silica were used for adsorption. Flow rates of up to 200 bed volumes per minute were employed for the adsorption step. Quantitative desorption of the pesticides was accomplished with less than 100l of solvent, thus eliminating the need for a solvent reduction step. The pesticides from samples of surface waters were adsorbed onto C-18 bonded porous silica at the sampling site and the cartridges containing the bonded phase were returned to the laboratory for elution and analysis. The analytical results obtained from use of this procedure agreed with those obtained for duplicate samples of the water that were processed in the laboratory using standard solvent extraction procedures.     

Controllable synthesis of silica nanoparticle size and packing efficiency onto PVP-functionalized PMMA via a sol–gel method

This study aimed to investigate synthesis and adsorption behavior of silica nanoparticles onto polyvinylpyrrolidone (PVP)-functionalized poly(methyl methacrylate) under various conditions such as methanol/water ratio, ammonium hydroxide concentration, polymer contents, tetraethylorthosilicate contents, and total volume of solvent via sol–gel method. First, the copolymerization of methyl acrylate as a comonomer and 1-dodecanethiol as a chain transfer agent increased the thermal stability of the product; however, the uniformity of the PMMA particles decreased because of the chain transfer reaction. Second, the adsorption behavior and size of silica nanoparticles could be controlled by adjusting the silica synthesis conditions. The adsorbed silica particle size was greatly influenced by the ammonium hydroxide concentration and the addition of water further enhanced the size increase. However, increasing the water content reduced the packing efficiency of the adsorbed silica particles. Increasing the PVP-functionalized PMMA content at a fixed TEOS content linearly decreased the silica particle size. But TEOS concentration did not significantly affect the silica particle size. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 662–672     

Conformation of adsorbed layers of polyNIPAM on silica in a binary solvent

The conformation of poly( N-isopropylacrylamide) chains adsorbed at a silica interface was studied as a function of concentration in the methanol-water binary solvent mixture. Both water and methanol are good solvents for PNIPAM; however, in certain mixtures cononsolvency is induced by a lowering of the LCST. This led to a decrease in the extent of the PNIPAM layer away from the interface as measured using the colloidal probe technique in the poor solvent region. At low methanol concentrations but still in the good solvent region capillary bridging between the silica surfaces with adsorbed PNIPAM layers was observed due to the increased methanol concentration in this interfacial region over that of the bulk. Furthermore, adsorption measurements showed that PNIPAM adsorbed only weakly to the silica interface with a low surface excess on the order of 0.23 mg/m (2), which allowed study of the behavior of the immobilized PNIPAM chains under highly dilute conditions using the quartz crystal microbalance. As the concentration of methanol increased toward the phase transition boundary, a slight contraction followed by an expansion of the PNIPAM was observed, which is in agreement with previous predictions from theory for polymers in solution.     

Focusing in Liquid Thermal Adsorption Systems

Focusing can be obtained in liquid thermal cycling zone adsorption by significantly increasing the temperature of the hot feed. To prevent boiling column pressure is raised. This method for concentrating dilute fluids was studied using the simulation package ADSIM. The systems studied were ethanol-water on silicalite and toluene-n-heptane on silica gel. Substantial concentration of dilute feeds while producing a pure solvent product were obtained. This research highlights the need for equilibrium data for liquid adsorption systems at elevated temperatures and pressures.     

Manipulating interfacial polymer structures through mixed surfactant adsorption and complexation

The effects of a nonionic alcohol ethoxylate surfactant, C(13)E(7), on the interactions between PVP and SDS both in the bulk and at the silica nanoparticle interface are studied by photon correlation spectroscopy, solvent relaxation NMR, SANS, and optical reflectometry. Our results confirmed that, in the absence of SDS, C(13)E(7) and PVP are noninteracting, while SDS interacts strongly both with PVP and C(13)E(7) . Studying interfacial interactions showed that the interfacial interactions of PVP with silica can be manipulated by varying the amounts of SDS and C(13)E(7) present. Upon SDS addition, the adsorbed layer thickness of PVP on silica increases due to Coulombic repulsion between micelles in the polymer layer. When C(13)E(7) is progressively added to the system, it forms mixed micelles with the complexed SDS, reducing the total charge per micelle and thus reducing the repulsion between micelle and the silica surface that would otherwise cause the PVP to desorb. This causes the amount of adsorbed polymer to increase with C(13)E(7) addition for the systems containing SDS, demonstrating that addition of C(13)E(7) hinders the SDS-mediated desorption of an adsorbed PVP layer.     

INVOLVEMENT OF PHYTOCHROME IN LIGHT CONTROL OF STEM ELONGATION IN CUCUMBER (Cucumis sativus L.) SEEDLINGS

A series of polycondensed aromatic N-heterocycles (acridine, benzo-f-quinoline 1,2,7,8-dibenzacridine and 3,4,5,6-dibenzacridine) were adsorbed from the gas phase and from liquid solution on highly dispersed silica gels with very different specific surface areas and pore sizes. The translational mobility of the adsorbed species was quantified by the triplet decay and the delayed fluorescence following bimolecular triplet-triplet annihilation after pulsed laser irradiation. The decay kinetics were analyzed with conventional second order rate equations and with the fractal approach. The first method is reliable without limitations on adsorbents with large pore diameters. It yields second order annihilation constants of 4 times 10¹²-6 times 10¹¹ dm² mol^?1 s^?1 depending on the masses and sterical requirements of the adsorbates. For the second method a spectral dimension d_s= 4/3 was used. This method is quantitatively applicable to all heterocycles adsorbed on silica gel 60 that have very small pore sizes. An activation energy of 4.9 ± 0.5 kcal mol^?1 was obtained for the translational diffusion of acridine on hydroxylated silica gel.