飞秒脉冲烧蚀单晶硅的超快动力学

利用基于Pump-probe系统的超快时间分辨阴影图的方法,研究了空气中飞秒激光烧蚀单晶硅的动力学过程。实验采用脉宽为50 fs、平均能量密度约35 J/cm2的单脉冲激光烧蚀单晶硅,获取飞秒激光烧蚀单晶硅过程中等离子体和冲击波的形成和发展过程的时间分辨阴影图。实验结果表明：飞秒激光烧蚀单晶硅导致其表面物质喷发的过程是不连续的,分为明显的两次喷发过程。这表明飞秒激光与单晶硅作用的过程中,在不同的时间段可能由不同的机制主导,在前期可能是多光子电离为主,在后期可能是由多光子效应和雪崩效应共同作用。研究还发现,延迟时间较长时,冲击波形状发生畸变。     

Thermal process of silica glass microchannels fabricated by femtosecond laser ablation

In order to improve the morphology of microchannels fabricated by femtosecond laser ablation, the thermal process was introduced into the post-treatment processing. It was found that the thermal process cannot only decrease the roughness but also the width and depth of the microchannel. The change rates of width, depth, and roughness of the microchannel increase with processing temperature. When we prolong the time of constant temperature, the change rate of the width decreases at the beginning, and then it tends to be stable. However,the change rates of depth and roughness increase, and then they tend to be stable. In this Letter, we discuss the reasons of the above phenomena.     

Thermal analysis of intense femtosecond laser ablation of aluminum

This paper numerically simulates the process of ablation of an aluminum target by an intense femtosecond laser with a fluence of 40 J/cm 2 based on the two-temperature equation,and obtains the evolution of the free electron temperature and lattice temperature over a large temporal and depth range,for the first time. By investigating the temporal evolution curves of the free electron temperature and lattice temperature at three representative depths of 0,100 nm and 500 nm,it reveals different characteristics and mechanisms of the free electron temperature evolution at different depths. The results show that,in the intense femtosecond laser ablation of aluminum,the material ablation is mainly induced by the thermal conduction of free electrons,instead of the direct absorption of the laser energy; in addition,the thermal conduction of free electrons and the coupling effect between electrons and lattice will induce the temperature of free electrons deep inside the target to experience a process from increase to decrease and finally to increase again.     

飞秒激光烧蚀硅表面产生微纳结构过程中激光脉冲数目的影响

为了研究飞秒激光脉冲数目与硅表面形貌之间的关系,在相同的SF6气体氛围下,改变照射硅表面的飞秒激光脉冲数,发现在飞秒激光照射下由硅表面形成的微型锥状尖峰的高度与飞秒激光脉冲数呈现一种非线性关系.通过对该关系的研究有利于找出在制造具有较高吸收效率的高微型锥状尖峰的"黑硅"的实验条件,有利于基于"黑硅"材料的光电器件转化效...     

Thermal melting and ablation dynamics on a femtosecond laser-heated highly-oriented pyrolytic graphite surface

Time-resolved optical reflection microscopy studies demonstrate spatiotemporal dynamics of melting and ablation of graphite surface molten by single IR femtosecond laser pulses, which are revealed by monitoring picosecond oscillations of the probe reflectivity modulated by transient acoustic reverberations in the surface melt. Temporal periods and amplitudes of the reverberations are affected through transient variations of melt thickness and acoustic impedance by melting, thermal expansion, spallation and fragmentation processes, thus enabling quantitative evaluation of their contributions and basic parameters.     

Polarization-dependent ablation of silicon using tightly focused femtosecond laser vortex pulses

We demonstrate experimentally that, in a tight focusing geometry, circularly polarized femtosecond laser vortex pulses ablate material differently depending on the handedness of light. This effect offers an additional degree of freedom to control the shape and size of laser-machined structures on a subwavelength scale.     

Experimental investigation of ablation efficiency and plasma expansion during femtosecond and nanosecond laser ablation of silicon

Femtosecond laser (Ti:sapphire, 100 fs pulse duration) ablation of silicon in air was compared with nanosecond laser (Nd:YAG, 3 ns pulse duration) ablation at ultraviolet wavelength (266 nm). Laser ablation efficiency was studied by measuring crater depth as a function of pulse number. For the same number of laser pulses, the fs-ablated crater was about two times deeper than the ns-crater. The temperature and electron number density of the laser-induced plasma were determined from spectroscopic measurements. The electron number density and temperature of fs-induced plasmas decreased faster than ns-induced plasmas due to different energy deposition mechanisms. Images of the laser-induced plasma were obtained with femtosecond time-resolved laser shadowgraph imaging. Plasma expansion in both the perpendicular and the lateral directions were compared. PACS 52.38.Mf; 52.30.-q     

Formation of silicon nanoparticles and web-like aggregates by femtosecond laser ablation in a background gas

We show that the mechanism of nanoparticle formation during femtosecond laser ablation of silicon is affected by the presence of a background gas. Femtosecond laser ablation of silicon in a H₂ or H₂S background gas yields a mixture of crystalline and amorphous nanoparticles. The crystalline nanoparticles form via a thermal mechanism of nucleation and growth. The amorphous material has smaller features and forms at a higher cooling rate than the crystalline nanoparticles. The background gas also results in the suspension of plume material in the gas for extended periods, resulting in the formation (on a thin film carbon substrate) of unusual aggregated structures including nanoscale webs that span tears in the film. The presence of a background gas provides additional control of the structure and composition of the nanoparticles during short pulse laser ablation. PACS 81.16.-c     

Thermal character in organic polymers with nanojoule femtosecond laser ablation

Ablation experiments with femtosecond (fs) laser pulse (pulse duration 37 fs, wavelength 800 nm) on organic polymers have been performed in air. The ablation threshold is found to be only several nanojoules. The diameters of the dots ablated in the organic polymers are influenced by the laser fluence and the number of laser pulses. It is observed that heat is diffused in a threadlike manner in all directions around the central focus region.Explanations of the observed phenomena are presented. A one-dimensional waveguide is also ablated in the organic polymers.     

Superresolved femtosecond laser ablation

The determinist behavior of the femtosecond ablation process allows morphing features well under the diffraction limit by utilizing the thresholding effect, down to the nanometer scale. Because there are a vast range of applications where scaling down the size of the features is a major concern, we investigate the use of superresolving pupil plane filters. As is well known, these filters redistribute the focused optical intensity for a narrower bright spot and, as a trade-off, increase the sidelobes. However, this drawback can be rendered insignificant if all the outer optical power is kept under the determinist threshold value. Two types of pure absorbing binary filter have been tried, giving credence to a size reduction of the ablations in fused silica.     

266 nm飞秒激光烧蚀单晶硅的分子动力学模拟

 基于Stillinger-Weber(SW)势和“x-分区”模型,用分子动力学方法模拟了266 nm飞秒激光烧蚀单晶硅的过程,给出了烧蚀过程的物理图像,烧蚀过程中材料内部缺陷的产生与发展最终导致整层材料被移除。对比研究了烧蚀材料中不同区域粒子的运动轨迹,结果体现了在固、液、气不同状态下粒子的运动特征。模拟了激光诱导应力波的传播,其速度为8.18 km/s。     

Lithographical laser ablation using femtosecond laser

Lithographical laser ablation was demonstrated using a femtosecond laser with a lithographical optical system. In this method, a femtosecond laser beam passes through a mask and the pattern is imaged on a film by a coherent optical system. As a result, the film is lithographically ablated, and a micron-sized pattern can be generated in a single shot. The resolution of generation was 13 m, and the narrowest width of a generated line was about 4 m. Moreover, the system was applied to transmission gratings as masks, and nano-sized periodic structures such as nano-sized hole matrices and nano-meshes were generated in a single shot. PACS 52.38.Mf; 42.25.Hz; 42.82.Cr; 81.16.-c     

Generation of web-like structures and nanoparticles by femtosecond laser ablation of silicon target in ambient air

Silicon nanoparticles were produced by femtosecond laser ablation in ambient air. Obtained samples were studied using dark-field optical microscopy, scanning electron microscopy and Raman-scattering spectroscopy. Two groups of structures can be found: (1) branched amorphous structures with a minimum element size of about 10 nm and incorporations of nanocrystals (0.6–6.6 nm from Raman scattering analysis); (2) larger crystal particles with smooth surface and a typical size of 50–200 nm that provide directional visible light scattering (at dark-field optical microscopy observations). An influence of environment on resulting phase composition of silicon nanoparticles was investigated by numerical evaluation of nanoparticle’s cooling rate. The calculation shows that cooling in ambient air ensures cooling rate sufficient for crystallization.     

Surface ablation of lithium tantalate by femtosecond laser

We report measurements of the laser induced breakdown threshold in lithium tantalate with different number of pulses delivered from a chirped pulse amplification Ti: sapphire system. The threshold fluences were determined from the relation between the diameter D² of the ablated area and the laser fluence F₀. The threshold of lithium tantalite under single-shot is found to be 1.84 J/cm², and the avalanche rate was determined to be 1.01 cm²/J by calculation. We found that avalanche dominates the ablation process, while photoionization serves as a free electron provider.     

Ethanol-assisted ablation of silicon and germanium by temporally shaped femtosecond pulses

A surprising phenomenon can be discovered by using femtosecond double-pulse ablation of silicon and germanium in ethanol. The ablation areas present an oscillation increase phenomenon when the pulse delay increases from 200 fs to 1 ps in the fluence range of 0.5–0.6 J∕cm2. In contrast, the ablation areas exhibit an oscillation decrease phenomenon as the pulse delay increases when the laser fluence F 0.5 J∕cm2, which is consistent with the results of the experiment in air. It is considered that the adjustment of the photon–electron coupling efficiency by pulse train technology plays an important role in the ablation process.     

Self-organized nanostructure by a femtosecond laser on silicon

In this paper, ripple structure and hole arrays were investigated. Techniques based on laser scanning microscopes for the processing of periodic structures on silicon with a femtosecond laser (800 nm, 1 kHz, 130 fs) had been used. Ripples and any holes were obtained after laser irradiation in air with S and P polarization. The effect of the scanning speed (v) and the lens with different numerical apertures (NA) on the laser-induced surface topography were studied. We found that the femtosecond laser produces periodic ripples on the silicon surface of the submicron level, the width of line has a tight relationship to the NA and scanning speed. Finally, we process the microapparatus on silicon, for which the wide channel was 800 nm.     

Periodic nanostructures self-formed on silicon and silicon carbide by femtosecond laser irradiation

Laser-induced periodic surface structures (LIPSS) were formed on Si and SiC surfaces by irradiations with femtosecond laser pulses in air. Different kinds of self-organized structures appeared on Si and SiC at laser fluences slightly higher than the damage threshold, which was measured by confocal laser scanning microscope. The characteristic spatial periodicity of every observed structure was estimated reading the peak values of the 2D Fourier transform power spectra obtained from SEM images. The evolution of the spatial periodicity was finally studied with respect to both the laser fluence and the number of laser pulses. As already observed for metals, the behavior of the spatial periodicity on laser fluence can be related to the parametric decay of laser light into surface plasma waves. Our results suggest a wide applicability of the parametric decay model on different materials, making the model a useful tool in view of different applications of LIPSS.     

飞秒脉冲激光辐照对硅发光性能的影响

利用飞秒脉冲激光对单晶硅进行辐照,研究了在不同环境(纯水和空气)和能量密度条件下激光刻蚀过后硅片的光致荧光特性.对于辐照后的硅片,利用了场发射扫描电子显微镜(FESEM)、能谱仪(EDS)、傅里叶红外光谱仪(FT-IR)、光致荧光光谱仪(PL)进行表征.结果显示:在空气中样品表面形成了条纹状微结构,纯水中硅片表面生成了尺寸更小的珊瑚状微结构;激光刻蚀后在硅片表面的生成物主要是SiOx(x2),在纯水中处理后硅片氧元素的含量接近是空气中的4倍;傅里叶变换红外透射谱中主要为Si—Si键(610 cm-1)和Si—O—Si键(1105 cm-1)的振动;在空气和纯水中激发出的荧光均为蓝光(420—470 nm),在各自最佳激发波长下,纯水中荧光强度比空气中强2到3倍,但是在可见光范围内荧光峰的位置和形状都基本没有发生变化.研究表明:氧元素在光致发光增强上起着重要作用,光致发光最主要是由形成的氧缺陷SiOx(x2)导致的,生成低值氧化物SiOx的多少决定了发光的强弱.     

飞秒激光作用下的硅表面微结构及发光特性

采用近红外飞秒激光辐照浸泡在硫酸溶液中的N型单晶硅片,激光波长800 nm,脉宽200 fs,重频1 kHz,平均功率为100 mW,而硫酸溶液的质量分数分别选择为0.1%和1%。辐照后硅表面呈直径为5~8 mm,高度15 mm的柱型结构。分析其荧光特性,并通过比较硅材料表面微结构与激光光源、扫描参数、硅片背景环境的关系,确定最佳辐照条件为激光扫描速度750 mm/s,扫描间距5 mm/s。最终在厚度0.5 mm、直径26 mm的硅片上获得10 mm×10 mm的方形扫描区域,荧光光谱显示激光扫描后的区域在700 nm附近有很强的荧光发射。分析结果表明飞秒激光扫描改变了样品的表面微结构尺寸,增大了吸收面积,扩展了荧光激发波长,有效提高了样品的吸收效率和荧光发光相对强度(超过扫描前发光相对强度的2倍),荧光发射谱的变化是由量子限制效应和表面态模型共同作用的结果。     

飞秒激光作用下的硅表面微结构及发光特性

 采用近红外飞秒激光辐照浸泡在硫酸溶液中的N型单晶硅片,激光波长800 nm,脉宽200 fs,重频1 kHz,平均功率为100 mW,而硫酸溶液的质量分数分别选择为0.1%和1%。辐照后硅表面呈直径为5~8 mm,高度15 mm的柱型结构。分析其荧光特性,并通过比较硅材料表面微结构与激光光源、扫描参数、硅片背景环境的关系,确定最佳辐照条件为激光扫描速度750 mm/s,扫描间距5 mm/s。最终在厚度0.5 mm、直径26 mm的硅片上获得10 mm×10 mm的方形扫描区域,荧光光谱显示激光扫描后的区域在700 nm附近有很强的荧光发射。分析结果表明飞秒激光扫描改变了样品的表面微结构尺寸,增大了吸收面积,扩展了荧光激发波长,有效提高了样品的吸收效率和荧光发光相对强度(超过扫描前发光相对强度的2倍),荧光发射谱的变化是由量子限制效应和表面态模型共同作用的结果。