Complete Oxidation of Methane Alumina Modified with Calcium, over Palladium Supported on Lanthanum, and Cerium Ions

The activity and thermal stability of Pd/Al2O3 and Pd/（Al2O3＋MOx） （M=Ca, La, Ce） palladium catalysts in the reaction of complete oxidation of methane are presented in this study. The catalyst supports were prepared by sol-gel method and they were dried either conventionally or with supercritical carbon dioxide. Then they were impregnated with palladium nitrate solution. The catalysts with unmodified alumina had a high surface area. The activity and thermal stability of the aluminasupported catalyst was also very high. The introduction of calcium, lanthanum, or cerium oxide into alumina support caused a decrease of the surface area in the way dependent on the support precursor drying method. These modifiers decreased the activity of palladium catalysts, and they required higher temperatures for the complete oxidation of methane than unmodified Pd/Al2O3. The improvement of the palladium activity by lanthanum and cerium support modifier was observed only at low temperatures of the reaction.     

乙二胺功能化树脂负载Pd(0)配合物：可重复使用的高活性Heck芳基化催化剂

The ethylenediamine-functionalized resin-supported Pd(0)complex was prepared from PdCl_2 and ethylenedia-mine-functionalized chloromethylated polystyrene,followed by reduction with KBH_4.The complex was character-ized by FT-IR,XRD,BET,SEM and EDS.The resin-supported catalyst exhibited high catalytic activity in theHeck reaction and could be reused up to 17 times in NMP or 16 times in DMF at 90 ℃ in the Heck reaction of io-dobenzene with acrylic acid.The leaching investigation disclosed that the palladium leaching was caused by the in-teraction of iodobenzene with the metal Pd(0)on supported catalyst.The leached palladium species in filtrate wasvery stable and could be reused five times after the solid catalyst was filtered off.A cross-transfer test in recyclingin the presence of additional carbon disclosed that the soluble leached palladium species had much higher catalyticactivity than supported and/or adsorbed palladium in solid-solution heterogeneous Heck reaction.     

Preparation,structural characterization of a novel egg-shell palladium sulfide catalyst and its application in selective reductive alkylation reaction

A novel egg-shell Pd-S catalyst with palladium metal as the core and a membrane of palladium sulfide as the surface has been prepared by sulphidizing Pd/C with H₂S.This catalyst is effective for the reductive alkylation of p-amino diphenylamine（PADPA） and methylisobutyl ketone（MIBK） to afford N-（1,3-dimethylbutyl）-N′-phenyl-p-phenylenedianine（DBPPD） with conversion up to 99.42%and selectivity to 97.46%.Comparing with the other common palladium sulfide catalysts,the membrane of palladium sulfide on the surface and the core of palladium metal cause the Pd on the surface of the new catalyst in a lower sulfur coordination, which improves its activity.Our result indicates that this new egg-shell Pd-S/C is an efficient hydrogenation catalyst.     

A facile approach to asymmetrical biaryls via coupling reaction of aryl halides with sodium tetraphenylborate catalyzed by MCM-41-supported sulfur palladium（0） complex

Various functionalized asymmetrical biaryls can be synthesized in high to excellent yields via coupling reaction of aryl iodides or bromides with NaBPh4 catalyzed by MCM-41-supported sulfur palladium(0)complex.This palladium complex can be easily recovered and reused many times without loss of activity.     

Theoretical Study on the Mechanism of Sonogashira Coupling Reaction

The mechanism of palladium-catalyzed Sonogashira cross-coupling reaction has been studied theoretically by DFT （density functional theory） calculations. The model system studied consists of Pd（PH3）2 as the starting catalyst complex, phenyl bromide as the substrate and acetylene as the terminal alkyne, without regarding to the co-catalyst and base. Mechanistically and energetically plausible catalytic cycles for the cross-coupling have been identified. The DFT analysis shows that the catalytic cycle occurs in three stages： oxidative addition of phenyl bromide to the palladium center, alkynylation of palladium（Ⅱ） intermediate, and reductive elimination to phenylacetylene. In the oxidative addition, the neutral and anionic pathways have been investigated, which could both give rise to cis-configured palladium（Ⅱ） diphosphine intermediate. Starting from the palladium（Ⅱ） diphosphine intermediate, the only identifiable pathway in alkynylation involves the dissociation of Br group and the formation of square-planar palladium（Ⅱ） intermediate, in which the phenyl and alkynyl groups are oriented cis to each other. Due to the close proximity of phenyl and alkynyl groups, the reductive elimination of phenylacetylene proceeds smoothly.     

PREPARATION AND CHARACTERIZATION OF BIMETALLIC Pd-Fe/Al_2O_3 CATALYSTS—CHARACTERIZATION BY INFRARED SPECTROSCOPY AND X-RAY DIFFRACTION

Series of bimetallic catalysts Pd-Fe/Al_2O_3 with various palladiumand iron contents were prepared by impregnating metal precursors in differentsequences.Techniques were employed to characterize the catalysts,XRD forthe existing form of the supported metals,XPS for the surface metal contentsand chemical states,in silu IR with the aid of CO as a probe molecule for theinfluence of iron amount and adding sequence upon the dispersion and the elec-tronic state of palladium.On the catalyst prepared by coimpregnating,the pal-ladium and iron contents are higher than those prepared by impregnating in dif-ferent sequence,but the ratio of Pd/Fe(in atom)is lower than those on thelatter two.The iron atoms shield the palladium and enhance the dispersity ofpalladium.In the catalyst prepared by first impregnating with iron and thenwith palladium,the iron has a strong ability to disperse palladium and the dis-persity increases with the iron loading.In the catalyst prepared by first dopingwith palladium and then iron,the     

Sonochemical Synthesis of Three-dimensional Aggregates of Pd Nanoparticles with High Electrocatalytic Activity Towards Ethanol Oxidation

Flower-like aggregates composed of （4.0±0.8） nm palladium（Pd） nanoparticles were prepared via ultrasonics in the palladium（Ⅱ） chloride（PdCl2） H2O/EtOH（5/1,volume ratio） solution with the addition of a quantity of poly（vinyl pyrrolidone）（PVP） and sodium dodecyl sulfonate（SDS）.The morphologies,crystal structures and the optical properties of the flower-like Pd nanostructures were characterized by X-ray diffraction（XRD）,X-ray photoelectron spectroscopy（XPS）,scanning electron microscopy（SEM）,transmission electron microscopy（TEM）,selected area electron diffraction（SAED） and UV-visible absorption spectroscopy,respectively.The mechanism of sonochemical reduction of Pd（Ⅱ） ions was also investigated.The results show that the molar ratio of PVP to SDS affected the formation of the flower-like aggregates of Pd nanoparticles.Moreover,the electrocatalytic properties of Pd aggregates modified glassy carbon electrode for ethanol oxidation were also investigated by cyclic voltammetry（CV）.This material exhibits remarkable electrocatalytic activity for ethanol oxidation in 1 mol/L KOH and appears as a promising candidate to be applied in direct ethanol fuel cells.     

PEG-stabilized palladium nanoparticles： An efficient and recyclable catalyst for the selective hydrogenation of 1,5-cyclooctadiene in thermoregulated PEG biphase system

Polyethylene glycol （PEG）-stabilized palladium nanoparticles were prepared and applied to the selective hydrogenation of 1,5- cyclooctadiene （1,5-COD） in thermoregulated PEG biphase system, which allows a reaction in a single-phase at a higher temperature followed by a phase split at a lower temperature. Under the optimized reaction conditions, the conversion of 1,5-COD and the selectivity of cyclooctene （COE） were 100 and 98%, respectively. The catalyst could be easily separated from the product by phase separation and reused for 6 times without evident loss in activity and selectivity. 2007 Yan Hua Wang. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.     

D301 resin as a solid base for phosphine-free Heck reactions with heteroaryl halides

A new and practical method of the D301 resin,a weak basic anion exchange resin with secondary amine functionality（Grade Matrix Structure：Styrene-DVB D301R）,used as base to Heck reactions catalyzed by palladium reagent without phosphine compound as ligand is described.It was found that the D301 resin used as base is an efficient and reusable base and can be regenerated and recycled in the reaction.The olefmation of heteroaryl halides prepared the corresponding products in good yields using D301 resin as base.     

PROPERTIES OF HIGHLY DISPERSED PALLADIUM CATALYSTS ON POLY N-VINYL-2-PYRROLIDONE

Four kinds of palladium catalysts dispersed on poly-N-vinyl-2-pyrrolidone were prepared by using CH3OH-NaOH, NaBH4, H2O or CH3OH-H2O as the reducing agent in the process of catalyst preparation. The catalysts were characterized by XPS, TEM, XRD and used for the hydrogenation of methyl acrylate. It was found that the valence state of palladium and distribution of palladium particles as well as the hydrogenation rate were greatly affected by the reducing agent. The best evenly dispersed palladium catalyst showing high hydrogenation activity was prepared using CH3OH-NaOH as the reducing agent.     

Catalytic Oxidation of Iron(II) Aqua Complex by Oxygen in the Presence of Palladium(II) Tetraaqua Complex

The catalytic oxidation of iron(II) with oxygen occurs along with an autocatalytic reaction between palladium(II) tetraaqua complex and iron(II) aqua complex in an oxygen atmosphere. The reaction is catalyzed by a compound of palladium in an intermediate oxidation state, presumably by a small palladium cluster formed in the course of the reduction of palladium(II) tetraaqua complex with iron(II) aqua complex.     

Palladium-catalyzed synthesis of 2,3-dihydro-2-ylidene-1,4-benzodioxins

Palladium-catalyzed condensation of benzene-1,2-diol with various propargylic carbonates afforded regio- and stereoselectively 2,3-dihydro-2-ylidene-1,4-benzodioxins. The reaction is suggested to proceed by the formation of a (sigma-allenyl)palladium complex, followed by the intermolecular attack of the phenoxide ion on this complex to generate a new (sigma-allyl)palladium complex in equilibrium with the corresponding (eta(3)-allyl)palladium complex. Intramolecular attack of the phenoxide ion afforded the corresponding benzodioxan compound. This last attack occurs predominantly at the more electrophilic end of the (eta(3)-allyl)palladium intermediate. The Z- or E-stereochemistry of the products was established by (1)H NMR and proton NOE measurements and also by X-ray analysis on an example. The Z-stereochemistry generally observed is in agreement with the formation of this (eta(3)-allyl)palladium intermediate. However, in the case of tertiary propargylic carbonates, the E-stereochemistry generally observed could be explained by an intramolecular attack of the phenoxide ion on the intermediate (sigma-allyl)palladium complex, in slow equilibrium with the (eta(3)-allyl)palladium complex.     

Ion- and atom-leaching mechanisms from palladium nanoparticles in cross-coupling reactions

Leaching of palladium species from Pd nanoparticles under C--C coupling conditions was observed for both Heck and Suzuki reactions by using a special membrane reactor. The membrane allows the passage of palladium atoms and ions, but not of species larger than 5 nm. Three possible mechanistic scenarios for palladium leaching were investigated with the aim of identifying the true catalytic species. Firstly, we examined whether or not palladium(0) atoms could leach from clusters under non-oxidising conditions. By using our membrane reactor, we proved that this indeed happens. We then investigated whether or not small palladium(0) clusters could in fact be the active catalytic species by analysing the reaction composition and the palladium species that diffused through the membrane. Neither TEM nor ICP analysis supported this scenario. Finally, we tested whether or not palladium(II) ions could be leached in the presence of PhI by oxidative addition and the formation of [Pd(II)ArI] complexes. Using mass spectrometry, UV-visible spectroscopy and 13C NMR spectroscopy, we observed and monitored the formation and diffusion of these complexes, which showed that the first and the third mechanistic scenarios were both possible, and were likely to occur simultaneously. Based on these findings, we maintain that palladium nanoparticles are not the true catalysts in C--C coupling reactions. Instead, catalysis is carried out by either palladium(0) atoms or palladium(II) ions that leach into solution.     

Interaction of CO with palladium supported on oxidized tungsten

A model catalyst system, palladium on tungsten oxide, has been examined by temperature-programmed desorption and photoemission spectroscopy. The samples were prepared by evaporation of palladium onto an oxidized tungsten foil under ultrahigh vacuum conditions. Mostly three-dimensional (3-D) palladium (Pd) clusters were found to be present on oxidized tungsten (WOx) surfaces at room temperature. Upon annealing to 670 K, the palladium clusters are redispersed and decorated by the WOx surface layer. The nature of the WOx phase on top of the palladium clusters is dependent on the mode of oxidation of the tungsten foil prior to palladium deposition. Mainly W(2+) species decorate palladium deposits on tungsten oxidized at room temperature, while mainly W(4+) species are on top of palladium deposits on the surface oxidized at 1300 K. The appearance of a Pd(n+)-O-W(4+) mixed oxide phase with n < 2 was observed on the oxidized tungsten surface. The substantial reduction (relative to nonannealed samples) of molecular CO coverage induced by annealing is discussed in terms of the changes in chemical composition and morphology of the outermost surface.     

Detection and reactivity of a palladium alkoxycarbene

A characterful carbene: The high electrophilicity of a genuine palladium alkoxycarbene, obtained by transmetalation, is evident in its reactivity. Nucleophilic attack on two electrophilic centers (red) is observed. Alkyl abstraction and addition to the carbene carbon by different nucleophiles occur. This palladium(II) alkoxycarbene also undergoes comproportionation with palladium(0) to give an unprecedented palladium(I) dimeric carbene (see scheme).     

Reduction of palladium(II) monoglycinate complexes at rotating disc palladium electrode in acid media

Reduction of palladium(II) glycinate complexes in strongly acid 0.5 M NaClO₄ solutions (pH 0.6 and 1.0) with variable palladium(II) complex and free glycine concentration was studied by the taking of cyclic voltammograms at palladium rotating disc electrode. It is shown that it was a chelate monoglycinate palladium(II) complex that was present in all studied solutions and underwent the reduction. The diffusion coefficient of the chelate monoglycinate palladium(II) complex D = (6.5 ± 0.5) × 10⁻⁶ cm²/s was determined from the limiting diffusion current of the complex reduction. The monoglycinate palladium(II) complex reduction occurred in the double-layer segment of the palladium charging curve; it was not complicated by hydrogen adsorption at electrodes. The palladium(II) complex reduction half-wave potential was determined (E _1/2 = ∼0.300 to 0.330 V (SCE)). It is shown that the decreasing of the number of ligands coordinated by palladium via nitrogen atom facilitates the complex reduction process. In particular, the reduction potentials of palladium(II) complexes with different ligand number at palladium electrode shifted markedly toward negative potentials in the series: Pdgly⁺ < Pd(gly)2 < Pd(gly)₄²⁻.     

Improved separation of palladium species in biological matrices by using a combination of gel permeation chromatography and isotachophoresis

The binding of palladium to high-molecular-mass compounds in palladium-treated lettuce is investigated as an example for a biological matrix. The total palladium concentration in lettuce leaves is 10.3 ng/g wet weight. After homogenization, high-molecular-mass compounds (> 10 kDa) are isolated by ultrafiltration. For separation of these palladium species a combination of preparative gel permeation chromatography (GPC) and preparative isotachophoresis (ITP) is used. Palladium is determined in separated fractions by using a highly sensitive total reflection X-ray fluorescence (TXRF) method after preconcentration. After GPC separation, four main fractions of palladium species are collected, each containing palladium in ng quantities (3-10 ng). Two of these fractions are further separated by ITP, yielding at least three main peaks per GPC fraction, each containing palladium in the range of 0.3-3 ng. These palladium containing peaks are characterized by high-performance size exclusion chromatography (HPSEC) and capillary isotachophoresis (cITP) in parallel. HPSEC enables the estimation of the molecular mass of six main palladium peaks, covering a molecular mass range of 69-200 kDa. It is also shown that the estimation of molecular mass after separation is more reliable than the respective estimation directly in the first GPC run. However, cITP reveals that each of the separated peaks is still a mixture of at least five different compounds.     

Palladium nanostructures and nanoparticles from molecular precursors on highly ordered pyrolytic graphite

Nanostructures and nanoparticles of palladium assembled on highly ordered pyrolytic graphite (HOPG) by the adsorption of palladium molecular precursors (MPs), in dichloromethane solutions, have been prepared. Self-assemblies of palladium nanostructures on HOPG were characterized by scanning electron microscopy (SEM), Auger electron spectroscopy (AES), transmission electron microscopy (TEM), and atomic force microscopy (AFM) techniques. In this work, palladium rings had a wide variety of sizes in the nanometer range, and the ring/tube structures were preserved after a reductive process in which palladium metallic nanoparticles were formed. Noncircular structures were observed at HOPG defects and atomic step sites, as well. It is proposed that the observed ring formation of the palladium molecular precursors on HOPG substrates is related to the functional groups in the MPs, van der Waals interactions between particles and between particle-substrate, as well as the wetting properties of the solvent. In the present work, we illustrate several examples of the formation and characterization of palladium complex tubes and the resulting palladium rings, via the reduction process.     

Carbon-Supported Palladium–Gold Bimetallic Disperse Systems Formed in Aqueous Solutions at 110°С

Various palladium–carbon composites have been manufactured by autoclaving at 170°С to be used as precursors for manufacturing bimetallic particles. The morphology of the manufactured items was comprehensively studied by scanning electron microscopy; the ultrafine metal palladium was found to have particles sizes lying in the range 30–120 nm. The specifics of hydrothermal reduction of gold(III) chloro complexes by palladium–carbon composites at 110°С have been studied. An appreciable increase in gold(III) reduction rate was observed with the use of a palladium–carbon composite relative to the rate observed for ultrafine metallic palladium. Gold is reduced on a palladium–carbon composite to an individual metallic phase.     

Insertion of molecular oxygen into a palladium(II) hydride bond

Insertion of molecular oxygen into a palladium(II) hydride bond to form an (eta1-hydroperoxo)palladium(II) complex is reported. The hydroperoxo palladium(II) product has been crystallographically characterized. A second-order rate law (first-order in palladium and first-order in oxygen) is observed for the reaction and a large kinetic isotope effect implicates Pd-H bond cleavage in the rate-determining step. The results of studies with radical inhibitors and light suggest that the reaction does not proceed by a radical chain mechanism.