固相萃取/超高效液相色谱-串联质谱法测定贝类中3种短裸甲藻毒素

建立了同时测定贝类中3种短裸甲藻毒素的超高效液相色谱-串联质谱法。样品采用丙酮提取、C18固相萃取柱净化;以5 mmol/L乙酸铵(含0. 1%甲酸)-乙腈为流动相,ACQUITYTMUPLC BEH C18色谱柱进行分离,在多反应监测模式下进行测定,外标法定量。结果表明,3种目标物在1. 0～100μg/L质量浓度范围内线性良好,相关系数(r~2)不小于0. 996,方法定量下限为3. 0μg/kg,回收率为80. 0%～87. 5%,相对标准偏差为1. 3%～5. 4%。该方法前处理简单,灵敏度高,稳定性好,适用于贝类中3种短裸甲藻毒素的同时测定。     

海产品、底泥、海水中扑草净药物残留量的液相色谱-串联质谱检测

建立了海产品、底泥、海水中扑草净药物残留量的液相色谱-串联质谱检测方法。对海产品、底泥样品,采用快速溶剂提取仪(ASE)乙腈提取,凝胶渗透色谱(GPC)净化,液质联用仪(LC-MS/MS)分析;对海水样品采用酸化乙腈提取,氨基固相萃取柱净化,LC-MS/MS分析。实验结果显示,扑草净在浓度0.025～8.0ng/mL时,线性关系良好(R2=0.9999);海产品、底泥样品的方法测定低限为0.25μg/kg,3个加标水平下的平均回收率为90.0%～105.4%,相对标准偏差(RSD)为2.9%～5.3%;海水样品的方法测定低限为0.50μg/L,3个加标水平下的平均回收率为79.5%～99.6%,RSD为3.4%～11.9%。该方法简单、快速、准确,可用于海产品、底泥、海水样品中扑草净的筛选和测定。     

有机悬浮固化分散液-液微萃取测定水样中痕量铅

建立了以二乙基二硫代氨基甲酸钠为配位剂,十二醇为萃取剂,乙醇为分散剂的悬浮固化分散液-液微萃取—火焰原子吸收光谱法测定水样中痕量铅的方法。详细探讨了影响萃取效率的因素。优化条件为:二乙基二硫代氨基甲酸钠的用量为10-6 mol,十二醇体积为90.00μL,乙醇体积为1.00 mL,pH为7.00。在最佳条件下,铅的检出限为1.12μg/L,富集倍率为16.00,线性范围5.00～600.00μg/L,对含有20.00μg/L和600.00μg/L Pb的标准溶液平行萃取测定11次,测定结果的RSD分别为3.73%和2.62%。本方法应用于自来水、河水及海水中痕量铅的分析,加标回收率为90.10%～100.70%。     

超高效液相色谱-串联质谱法同时测定动物类中药材中6种伏马毒素

建立超高效液相色谱-串联质谱法同时测定动物类中药材中6种伏马毒素。样品经20 mL 80%乙腈水溶液提取,离心后上清液用QuEChERS EMR-Lipid净化包净化,净化液采用超高效液相色谱-串联质谱法在多反应监测模式下测定6种伏马毒素含量,色谱峰面积外标法定量。6种伏马毒素在质量浓度为2～40 ng/mL范围内线性关系良好,相关系数均大于0.999,检出限为0.4～1.4μg/kg。在16、40、80μg/kg 3个加标浓度水平下,平均回收率为77.3%～101.6%,相对标准偏差为1.7%～8.4%(n=6)。该方法简单快速,定性定量准确,可用于动物类中药材中伏马毒素的检测。     

超高效液相色谱-串联质谱法测定水产中10种麻痹性贝类毒素

建立超高效液相色谱–串联质谱法测定贝类中麻痹性贝类毒素的方法。样品经0.5%甲酸加热提取,石墨化炭黑固相萃取柱净化后,用超高效液相色谱–串联质谱法测定。采用TSK–Gel Amide–80色谱柱(150mm×2.0mm,5μm),以水溶液(含2mmol/L甲酸铵,50mmol/L甲酸)A,95%乙腈水溶液(含2mmol/L甲酸铵,50 mmol/L甲酸)B为流动相,梯度洗脱,流量为0.3 mL/min,进样体积为10μL,多反应监测(MRM)模式检测。藤沟藻毒素3、4(GTX3、GTX4)、脱氧藤沟藻毒素3(dcGTX3)的检出限为8μg/kg,藤沟藻毒素5(GTX5)、新石房蛤毒素(neoSTX)、石房蛤毒素(STX)、脱氧甲酰基类毒素(dcSTX)的检出限为20μg/kg,藤沟藻毒素1,2(GTX1,GTX2)的检出限为24μg/kg,脱氧藤沟藻毒素2(dcGTX2)的检出限为28μg/kg。GTX3,dcGTX3,GTX4的线性范围为4～80μg/L,GTX5,neoSTX,STX, deSTX的线性范围为10～200μg/L,GTX1的线性范围为12～240μg/L,GTX2的线性范围为11～220μg/L,dcGTX2的线性范围为14～280μg/L,线性相关系数均大于0.99,平均回收率为82.5%～115.1%,测定结果的相对标准偏差为0.6%～7.5%(n=6)。该方法检出限低,精确度高,适用于水产品中麻痹性贝类毒素的检测。     

超声辅助基质分散液-液微萃取/气相色谱-串联质谱法测定水中48种半挥发性有机物

建立了超声辅助基质分散液-液微萃取(UA-DLLME)/气相色谱-串联质谱(GC-MS)同时测定地下和地表水中15种硝基苯、19种苯胺和14种邻苯二甲酸酯类化合物的分析方法。采用Plackett-Burman设计从萃取剂、分散剂体积、萃取温度、萃取时间和离子强度等变量中筛选最显著的影响因素,并利用中心组合设计(CCD)结合响应曲面图优化显著因素,最终确定最佳的萃取条件:10 mL水样在2 g/L NaCl条件下迅速加入0.65 mL乙腈(分散剂)和40μL四氯化碳(萃取剂),于40℃超声2 min,混合液以3 500 r/min离心3 min。结果显示,目标分析物在1～200μg/L质量浓度范围内线性良好,相关系数不低于0.995 8,方法的检出限(MDL)为0.001～0.030μg/L,定量下限(LOQ)为0.004～0.120μg/L,在低、中、高3个加标浓度下的平均回收率为77.4%～113%,相对标准偏差(RSD)均不高于9.6%(n=6)。     

小体积液液萃取-气相色谱-三重四极杆串联质谱法测定地下水中32种半挥发性有机污染物

建立小体积液液萃取-气相色谱-三重四极杆串联质谱法测定地下水中32种半挥发性有机污染物（SVOCs）的方法。采用2 mL二氯甲烷和正己烷混合溶剂（体积比为1∶1）加入到20 mL水样中,添加2 g NaCl,涡旋萃取60 s,经DB-5MS UI色谱柱（30 m×0.25 mm,0.25μm）分离,SRM模式检测,内标法定量。32种SVOCs的质量浓度在0.5～20μg/L范围内与色谱峰面积具有良好的线性关系,相关系数均大于0.995,方法检出限为0.002～0.06μg/L。样品加标回收率为72.5%～129%,测定结果的相对标准偏差为0.65%～21.1%(n=6)。该方法样品处理简单快捷,所需水样和有机试剂体积较少,能够满足地下水中32种SVOCs的高效测定。     

UPLC-MS/MS测定海水、悬浮颗粒物及沉积物中18种藻毒素

采用固相萃取结合超高效液相色谱-串联质谱（UPLC-MS/MS）同时检测18种海洋藻毒素,包括原多甲藻酸贝类毒素（AZAs）、裸藻毒素（BTXs）、太平洋雪卡毒素（P-CTXs）、鳍藻毒素（DTXs）、米氏裸甲藻贝类毒素（GYM）、刺尾鱼素（MTX3）、大田软骨酸毒素（OA）、扇贝毒素（PTX2）、螺环内酯毒素（SPX1）及虾夷扇贝毒素（YTXs）。海水（1 L）或悬浮颗粒物及沉积物（1 g）的超声萃取液经Agilent Bond Elut C18(500 mg/6mL)固相萃取柱净化萃取后,在洗脱液中加入10%丙三醇-甲醇溶液以减少目标物损失。以95%乙腈水和水（两相均含有0.1%甲酸和2 mmol/L甲酸铵）为流动相,目标物经Phenomenex Kinetex C18色谱柱（100 mm×2.1mm i. d.,1.7μm）分离,采用电喷雾串联质谱多反应监测模式下正、负离子同时检测,外标法定量。18种藻毒素在6 min内分离良好,在线性范围内的相关系数为0.991 1～0.999 9,定量下限为0.05～250 pg/L（或pg/g）。三水平六平行的加标回收率为77.4%～119...     

固相支持液-液萃取/液相色谱-串联质谱法测定人全血中环孢素A

采用固相支持液-液萃取/液相色谱-串联质谱(LC-MS/MS)技术建立了人全血中环孢素A的分析方法。全血样品经蛋白沉淀后,上样至固相支持液-液萃取柱,经甲基叔丁基醚洗脱,Shim-pack XR-ODS色谱柱(75 mm×3. 0 mm i. d.,2. 2μm)分离,电喷雾电离源、正离子模式和多反应监测模式下采集数据,以环孢素D为内标物定量。结果表明,环孢素A在1. 5～500μg/L范围内呈良好的线性关系,相关系数(r)为0. 998,检出限和定量下限分别为0. 5μg/L和1. 5μg/L,在50、100、400μg/L 3个加标浓度下的平均回收率为78. 6%～83. 5%,日内和日间相对标准偏差(n=3)分别为3. 1%～5. 6%和4. 5%～8. 3%。该方法操作简便、灵敏度高,可用于全血中环孢素A的分析。     

温控离子液体分散液液微萃取结合高效液相色谱法检测脐橙中染色剂残留

建立了QuEChERS-温控离子液体分散液液微萃取结合高效液相色谱法快速检测脐橙中5种染色剂残留的分析方法。QuEChERS前处理步骤:样品用乙腈快速提取,NaCl和无水MgSO4除水后,经N-丙基乙二胺净化。温控离子液体分散液液微萃取步骤:QuEChERS前处理的净化液(1 mL)为分散剂,1-辛基-3-甲基咪唑六氟磷酸盐离子液体(60μL)为萃取剂,55℃水浴12 min,将目标物富集。用高效液相色谱-紫外检测器分析,检出样品用超高效液相色谱-串联质谱确证。在0.01和0.05 mg/kg的添加水平下,5种染色剂的平均回收率为70.3%~93.6%,相对标准偏差为3.5%~9.2%,定量限为1.1~2.8μg/kg。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.