Li2O-2B2O3熔体的物性研究

系统测量了四硼酸锂(Li2O-2B2O3)熔体的密度ρ、表面张力γ随着温度的变化规律,实验结果表明在1100K到1500K范围内Li2O-2B2O3高温熔体的密度和表面张力随着温度的升高均线性减小.通过实验数据拟合得出熔体密度与温度关系为ρ(T)=2.574-4.89×10-4T,熔点处LiO-2B2O3熔体的密度为1.992g/cm3;熔体表面张力与温度关系的拟合公式为γ=262.8-4.59×10-2T.     

非晶态锂离子导体B2O3-0.7Li2O-0.7LiCl-xAl2O3-0.1V2O5的电学性质和电子自旋共振研究

对两种非晶态B₂O₃-0.7Li₂O-0.7LiCl-xAl₂O₃-0.1V₂O₅(x=0.05和0.15),用差热分析、电导率测量、X射线衍射和电子自旋共振进行研究,发现:1)V₂O₅不仅作非晶网络形成剂,而且改变了晶化过程;2)对B₂O₃-Li_{2关键词：}     

非晶态锂离子导体B2O3-0.7Li2O-0.7LiCl-xAl2O3

木文研究了Al₂O₃对B₂O₃-0.7Li₂O-0.7LiCl非晶态的形成和电学性能的影响,我们发现:加入适量的Al₂O₃后,无需借助液氮骤冷技术,直接将熔体倾倒在室温下的紫铜板上就很容易形成大块非晶锂离子导体B₂O₃-0.7Li₂O-0.7LiCl-xAl₂O₃。Al₂O₃的加入使B₂O₃-0.7Li₂O-0.7LiCl的电导率有所降低,但在高温下不太明显,电导激活能略微升高,实验发现:Al₂O₃含量x=0.03是较合适的剂量,较容易形成大块非晶态,对电导率的影响也不大。 关键词：     

非晶锂离子导体P2O5-0.7Li2O-0.4LiCl-0.1Al2O3的离子导电性与结构研究

本文研究了非晶锂离子导体P₂O₅-0.7Li₂O-0.4LiCl-0.1Al₂O₃的60目、120目、200目粉末、粉末压片和整片非晶在60至380℃的离子电导率和激活能。发现颗粒度减小能使离子电导率提高四倍以上,但不影响激活能,它归因于同一非晶相的界面效应。各样品在380℃等温热处理76h内的离子电导率和X射线衍射研究表明:颗粒度越小,晶化就越容易。整片非晶比粉末压片不仅电导率提高两个数量级,激 关键词：     

非晶态B2O3-0.7Li2O-0.7LiCl电导率频谱的研究

本文对非晶态快离子导体的B₂O₃-0.7Li₂O-0.7LiCl的电导率与外电场频率的关系进行了研究。结果表明:在较宽的频率范围内,样品的体电导约等于总电导;电导率频谱在中频段有一平台,在高频段上升,而且温度越高,开始上升的频率也越高。这一结果使电导率的测定有可能简化,即可以采用交流电桥法或在某一合适频率下采用交流伏安法直接测量样品的总电导或总导纳的模值作为体电导的值,从而求得电导率。本文考虑到非晶态结构的长程无序对离子迁移的影响,从局域极 关键词：     

非晶锂离子导体B2O3-0.7Li2O-0.7LiCl-xAl2O3晶化初期的核磁共振研究

通过真空密封热处理、避免了样品晶化后吸水引起的误差,采用脉冲法在293K和77K测量了晶化过程初期三种非晶锂离子导体B₂O₃-0.7Li₂O-0.7LiCl-xAl₂O₃(x=0.15,0.10和0.05)的⁷Li核磁共振谱。发现在低温(77K)只有固相锂离子对应的自旋-自旋弛豫时间T₂=87μs,严格按高斯函数衰减。在室温下固相锂离子对应的T_2s=127μs,仍是高斯型;但液相锂离子对应的T₂却按洛仑兹函数衰减。这反映出锂离子导体的固-液二相性。三种非晶B₂O₃-0.7Li₂O-0.7LiCl-xAl₂O₃(x=0.15,0.10和0.05)分别在热处理温度401,388和381℃附近,其液相锂离子对应的T_2l都剧增,其吸收谱线宽都变窄。由此再次验证了非晶母体与微晶之间的两相界面效应的物理图象。 关键词：     

Li2B4O7晶体及其熔体结构的拉曼光谱研究

采用高温原位拉曼光谱技术,研究了Li₂B₄O₇从常温至1 373 K温度范围内的拉曼光谱。在升温过程中,晶体的拉曼光谱出现展宽和红移现象,且强度降低。晶体熔化时,由2个[BO₄]和2个[BO₃]组成的[B₄O₉]环状结构转变成(B₃O₆)3- 六元环和[BO₃]结构,[BO₄]结构减少直至消失。基于密度泛函理论,计算了Li₂B₄O₇晶体的拉曼光谱,对其振动模式进行了分析归属。利用量子化学从头计算法计算了由[B₃O₆-BO₃]为基础相互连接形成的x(Li₂B₄O₇)(x=2, 3, …, 9)的环状团簇模型的拉曼光谱,对Li₂B₄O₇熔体的结构进行了模拟分析。计算结果表明Li₂B₄O₇熔体的阴离子基元为三个(B₃O₆-BO₃)组成的大三元环超级结构。     

纯Cr2O3包覆Li4Ti5O12微球的制备及其储锂性能研究

The pure Cr₂O₃ coated Li₄Ti₅O₁₂ microspheres were prepared by a facile and cheap solutionbased method with basic chromium(III) nitrate solution (pH=11.9). And their Li-storage properties were investigated as anode materials for lithium rechargeable batteries. The pure Cr₂O₃ works as an adhesive interface to strengthen the connections between Li₄Ti₅O₁₂ particles, providing more electric conduction channels, and reduce the inter-particle resistance. Moreover, LixCr₂O₃, formed by the lithiation of Cr₂O₃, can further stabilize Li₇Ti₅O₁₂ with high electric conductivity on the surface of particles. While in the acid chromium solution (pH=3.2) modification, besides Cr₂O₃, Li₂CrO₄ and TiO₂ phases were also found in the final product. Li₂CrO₄ is toxic and the presence of TiO₂ is not welcome to improve the electrochemical performance of Li₄Ti₅O₁₂ microspheres. The reversible capacity of 1% Cr₂O₃-coated sample with the basic chromium solution modification was 180 mAh/g at 0.1 C, and 134 mAh/g at 10 C. Moreover, it was even as high as 127 mAh/g at 5 C after 600 cycles. At-20℃, its reversible specific capacity was still as high as 118 mAh/g.     

Li2O-(LiCl)2-B2O3-Al2O3系统玻璃的声学性质

本工作测量了Li₂O-(LiCl)₂-B₂O₃-Al₂O₃系统玻璃的密度、超声速,计算了玻璃的绝热压缩系数,从声学性质分析了玻璃骨架结构随组成的变化,为研究玻璃的离子导电性提供了方法和分析的依据。 关键词：     

Li2O-(LiCl)2-B2O3-Al2O3系统玻璃的Raman光谱研究

我们用Raman光谱研究了Li₂O(LiCl)₂B₂O₃-Al₂O₃系玻璃的结构,着重研究了Al₂O₃的影响。对于Li₂O-B₂O₃系玻璃,Li₂O含量增加使玻璃中存在的BO₃三角体转变为BO₄四面体, 关键词：     

Luminescence characteristics of Cu- and Eu-doped Li2B4O7

Photoluminescence, radioluminescence as well as optical absorption techniques were used to characterize Cu- and Eu-doped lithium tetraborate. The effect of host modification (single crystal and glassy state) and a limited range of dopant content were investigated. Time-resolved measurements were helpful to identify the emitting species.     

Effect of Bi2O3 content on physical and optical properties of 15Li2O-15K2O-xBi2O3-(65−x) B2O3: 5V2O5 glass system

Multi-component bismuth borate glasses doped with vanadium ions 15Li₂O-15K₂O-xBi₂O₃-(65−x) B₂O₃: 5V₂O_5, (x=3, 5, 7, 10, 12 and 15) have been prepared using conventional melt quench technique. Characterization of the prepared glasses has been done using X-ray diffraction, differential scanning calorimetry and density measurements. The effect of Bi₂O₃ content on the optical properties of the present glass system is studied from the optical absorption spectra recorded in the wavelength range 200-800 nm. The fundamental absorption edge has been identified from the optical absorption spectra. The values of optical band gap for indirect allowed transitions have been determined using available theories. The origin of the Urbach energy is associated with the phonon-assisted indirect transitions. The density and molar volume studies indicate that Bi₂O₃ in these glasses is acting partly as network modifier and partly as network former. The variations in the optical band gap energies, density and molar volume with Bi₂O₃ content have been discussed in terms of changes in the glass structure. Values of the theoretical optical basicity, average crosslink density and the average electronic polarizability are also reported.     

非晶离子导体B2O3-0.7Li2O-0.7LiCl-xAl2O3晶化过程的正电子湮没寿命谱和扫描电子显微镜研究

传统的粉末压片样品严重影响了正电子湮没寿命谱及电子显微镜测量的准确性和重复性。本文克服了以上困难,制出大片非晶离子导体样品,得到了晶化过程正电子湮没寿命谱及扫描电子显微镜研究的新结果。非晶离子导体B₂O₃-0.7Li₂O-0.7LiCl-xAl₂O₃的实验结果发现:Al₂O₃组分不同对非晶态样品在室温下的正电子平均寿命无较大影响。完全晶化后,正电子平均寿 关键词：     

Etudes electrique et Raman des verres du systeme B2O3 - Li2O - Li2SO4

New vitreous electrolytes with fast lithium ion carriers have been obtained in the B₂O₃ - Li₂O - Li₂SO₄ system. The variation of the ionic conductivity is discussed. Raman spectroscopy indicates that sulfate ions are diluted in the vitreous matrix without detectable interaction with the surrounding.     

Electrical and electrochemical properties of glass-ceramic electrolytes in the systems Li2S-P2S5-P2S3 and Li2S-P2S5-P2O5

Electrical and electrochemical properties of the 70Li₂S·(30 − x)P₂S₅·xP₂S₃ and the 70Li₂S·(30 − x)P₂S₅·xP₂O₅ (mol%) glass-ceramics prepared by the mechanical milling technique were investigated. Glass-ceramics with 1 mol% P₂S₃ and 3 mol% P₂O₅ showed the highest conductivity of 5.4 × 10^− 3 S cm^− 1 and 4.6 × 10^− 3 S cm^− 1, respectively. Moreover, these glass-ceramics showed higher electrochemical stability than the 70Li₂S·30P₂S₅ (mol%) glass-ceramic. From the XRD patterns of the obtained glass-ceramics, trivalent phosphorus and oxygen were incorporated into the Li₇P₃S₁₁ crystal. We therefore presume that the Li₇P₃S₁₁ analogous crystals, which were formed by incorporating trivalent phosphorus and oxygen into the Li₇P₃S₁₁ crystal, improve the electrical and electrochemical properties of the glass-ceramics. An all-solid-state cell using the 70Li₂S·29P₂S₅·1P₂S₃ (mol%) glass-ceramic as solid electrolyte operated under the high current density of 12.7 mA cm^− 2 at the high temperature of 100 °C. The cell showed an excellent cyclability of over 700 cycles without capacity loss.