Novel stand-alone PVA mixed matrix membranes conjugated with graphene oxide for highly improved reverse osmosis performance

In this research, an innovative Poly (vinyl alcohol) (PVA) reverse osmosis (RO) membrane with exceptional attributes was fabricated. Graphene Oxide (GO) nanosheets and Pluronic F-127 were infused within crosslinked PVA to fabricate thin film mixed matrix membranes. The newly synthesized membranes were evaluated in terms of several parameters like surface roughness, hydrophilicity, salt rejection, water permeability, Chlorine tolerance and anti-biofouling property, utilizing a dead-end RO filtration unit. Typical characterization techniques were used to assess the characteristics of the membranes. These include SEM, AFM, contact angle measurements and mechanical strength analysis. The conjugation of Pluronic F-127 and GO enhanced the overall performance of the membranes. The modified membranes surfaces had less roughness and higher hydrophilicity in comparison with the unmodified ones. This research showed that membranes that contained 0.08 wt% and 0.1 wt% GO exhibited superior selectivity, mechanical strength, Chlorine tolerance and anti-biofouling property. The truly significant outcome to evolve from this investigation is that improvements have been accomplished while PVA was used as a stand-alone RO layer without the use of any substrate. This study showed that crosslinking of PVA and modifying it with proper fillers overcame the common PVA downsides, primarily swelling and rupture under exceptionally high pressure.     

Preparation and characterization of novel physically cross-linked hydrogels composed of poly(vinyl alcohol) and amine-terminated polyamidoamine dendrimer

Poly(vinyl alcohol) (PVA) and polyamidoamine (PAMAM) dendrimers are water-soluble, biocompatible and biodegradable polymers, which have been widely applied in biomedical fields. In this paper, novel physically cross-linked hydrogels composed of PVA and amine-terminated PAMAM dendrimer G6-NH(2) were prepared by cyclic freezing/thawing treatment of aqueous solutions containing PVA and G6-NH(2). The FT-IR analysis and elemental analysis indicated that PAMAM dendrimer G6-NH(2) was successfully introduced into the formed hydrogels, possibly via hydrogen bonds among hydroxyl groups, amide groups and amino groups in PVA and PAMAM dendrimer in the process of freezing-thawing cycle. Compared with physically cross-linked PVA hydrogel, PVA/G6-NH(2) hydrogels show higher swelling ratios and faster re-swelling rate due to the higher hydrophilicity of PAMAM dendrimer G6-NH(2). Higher contents of G6-NH(2) in PVA/G6-NH(2) hydrogels resulted in higher swelling ratios and faster re-swelling rates. With increasing freezing/thawing cyclic times, the swelling ratios and re-swelling rates of PVA/G6-NH(2) hydrogels decreased, which is similar to that of physically cross-linked PVA hydrogel. Combining the special host property of polyamidoamine dendrimer, these novel physically cross-linked hydrogels are expected to have potential use in drug delivery, including improving drug-loading amounts in hydrogels and prolonging drug release time. Swelling ratios of physically cross-linked PVA/G6-NH(2)-50 hydrogels prepared by three, six, nine freezing/thawing cycles. The swelling equilibrium experiments were carried out in distilled water at 25 degrees C.     

Development and physicochemical characterization of doxorubicin-encapsulated hydroxyapatite–polyvinyl alcohol nanocomposite for repair of osteosarcoma-affected bone tissues

Nowadays locoregional therapy for cancer treatment can be associated with nanocomposite drug delivery systems. Coated nanoparticles have versatile applications for delivering chemotherapeutic drugs to the targeted part of the body. In this study, a ceramic carrier like nanosized hydroxyapatite (HAp) was synthesized by the in situ precipitation method followed by coating with anticancer drug like doxorubicin (DOX) and polyvinyl alcohol (PVA) polymer. The physicochemical characterization of the prepared polymer-coated drug ceramic nanocomposite (DOX-HAp-PVA) was carried out using Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron spectroscopy, and particle size distribution. Furthermore, the biocompatibility and the anticancer activity of the nanocomposite were explored by MTT assay study. Successfully synthesized DOX-HAp-PVA nanocomposite exhibited a remarkable cytotoxicity toward osteosarcoma cells (MG 63), which may be potentially used as an anticancer agent against osteosarcoma.     

Alkaline Zn-air and Al-air cells based on novel solid PVA/PAA polymer electrolyte membranes

High ionic conducting solid polymer electrolyte membranes (SPEM) had been successfully prepared from poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA). The solution casting method yielded highly hydrophilic membranes with uniform structure that were suitable for electrochemical applications. The room temperature ionic conductivity of the alkaline PVA/PAA polymer electrolyte membranes was in the range of 0.142–0.301 S cm⁻¹ depending on the composition. The cyclic voltammetry analysis was carried out using Zn|SPEM|Zn and Al|SPEM|Al cells. The analysis results revealed the excellent electrochemical stability of these newly developed alkaline solid PVA/PAA polymer electrolyte membranes. Metal-air fuel cells were also prepared from the alkaline solid PVA/PAA polymer electrolyte membranes. The electrochemical cell performance was evaluated based on Zn-air and Al-air cells at C/10 and C/5 discharge rates. The experimental results exhibited high percent of utilization for metal powders at room temperature. It was up to 90% for Zn-air cell when assembled with PVA:PAA = 10:7.5 polymer electrolyte membrane and discharged at C/10 rate. The power density could be as high as 50 mW cm⁻² at room temperature. However, the cell percent utilization was reduced to 73% with the same composition electrolyte membrane when C/5 discharge rate was tested.     

Preparation,Characterization and Controlled Release Investigation of Biocompatible pH-Sensitive PVA/PAA Hydrogels

In the present research hydrogel films based on polyvinyl alcohol (PVA) and polyacrylic acid (PAA) blend, with various crosslink densities, have been prepared through different thermal treatment. The results of FTIR and DSC confirmed quality and quantity of conclusion on miscibility of PVA/PAA blends, respectively. Besides, biocompatibility of the samples has been proved in cytotoxicity tests using L929 cells, according to ISO10993–5. Water uptake of the hydrogel blends is measured. pH sensitivity properties of blends are studied with and without boiling in NaOH solutions where the effect of swelling in water before boiling has also been investigated. Preswellings in water and NaOH concentration have been found to be mainly effective on pH sensitivity of PVA/PAA blends. Biocompatibility and pH sensitivity behavior make these hydrogels appropriate candidates to orally deliver drugs such as insulin and peptides that can be released in basic pH of intestine. The stability of these films in acidic solutions and its expansion and also the consequent release of drugs in basic solutions have been studied by using Teofilin as a model drug by UV-spectrophotometeric measurements.     

PVA/PAA thermo-crosslinking hydrogel fiber: preparation and pH-sensitive properties in electrolyte solution

The preparation of thermo-crosslinking hydrogel fibers composed of poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA) was presented. The hydrogel fiber was prepared by extruding the spinning dope from in situ polymerization of acrylic acid in the presence of PVA into coagulating bath of saturated ammonium sulfate aqueous solution. The network was formed by thermally heating the dried fibers under vacuum. The final hydrogel fibers exhibit pH-sensitive behavior and show hysteresis loop in the pH range from 2.5 to 12.5. The pH value at which the swelling ratio of the fiber had a jump shifted to lower value with increasing the PAA content within the network. Increasing the heating temperature and time for the fibers, the swelling ratio decreased and the jump point pH shifted to higher pH value. The oscillatory swelling/contracting behavior of the hydrogel fiber exhibited a well reversible pH-responsive property.     

In-vitro hemocompatibility evaluation of a thermoplastic polyurethane membrane with surface-immobilized water-soluble chitosan and heparin

The surface of a thermoplastic polyurethane (TPU) membrane was treated with low temperature plasma (LTP) and was then grafted with poly(acrylic acid) (PAA), followed by the grafting of water-soluble chitosan (WSC) and heparin (HEP). The surface was characterized with static contact-angle and X-ray photoelectron spectroscopy (XPS). The results showed that the surface densities of peroxides and PAA reached a maximum when treated with LTP for 90 s. A higher pH of the reacting solution led to higher graft densities of WSC and HEP. After WSC and HEP grafting, the hydrophilicity of the TPU membrane was increased. The adsorption of proteins on HEP-grafted TPU membranes was effectively curtailed. In addition, HEP grafting also reduced platelet adhesion, elevated thrombin inactivation, and prolonged the blood coagulation time. According to the L929 fibroblast cell growth inhibition index, the HEP-grafted TPU membranes exhibited non-cytotoxicity. Overall results demonstrated that the HEP immobilization could not only improve the hydrophilicity but also the hemocompatibility of the TPU membrane, while maintaining the ascendant biocompatibility.     

pH敏感的聚(L-谷氨酸)-交联聚丙烯酸水凝胶的合成与性能研究

通过在聚L-谷氨酸侧链部分接枝甲基丙烯酸2-羟乙酯得到含有双键的聚(L-谷氨酸),将其与丙烯酸共聚得到由聚(L-谷氨酸)侧链接枝并交联聚丙烯酸的pH敏感水凝胶.研究水凝胶在不同pH的缓冲溶液中的溶胀性、溶胀动力学,并通过SEM观察水凝胶的微观结构.结果表明,水凝胶在低pH环境下的溶胀率明显低于高pH环境中的溶胀率,不同...     

Evaluation and correlation of electrochemical and mechanical properties of PVA/SA nanofibres

The present study evaluates and correlates the morphology of poly (vinyl alcohol) (PVA) and sodium alginate (SA) nanofibres with their internal structure to determine dielectric and tensile properties for future applications as long-lasting and resistant cell scaffolds. This work generates electrospun nanofibres mixing SA concentration in a PVA solution cross-linked in calcium chloride media. The dielectric properties of the nanofibres that were obtained using electrochemical impedance spectroscopy (EIS) show that at higher amount of SA in the PVA/SA fibres, the cross-linking process occurs at shorter times, indicating the modification of the internal structure of the PVA/SA. The X-ray photoelectron spectra (XPS) demonstrate that the chemical composition of the nanofibres varies depending on the depth profile. The transmission electron microscopy (TEM) proves that the PVA/SA is formed as a core-shell coaxial nanofibre. The tensile testing demonstrates that with a higher SA concentration, the mechanical properties show brittleness.     

PVA/PAA水凝胶纤维的电刺激响应性能

以过硫酸胺为引发剂,在PVA水溶液中原位聚合丙烯酸单体,得到的PVA／PAA混合水溶液在凝固浴硫酸胺饱和水溶液中纺丝制备了物理缠结和氢固定网络形式的PVA／PAA水凝胶纤维。该纤维于NaCl溶液中在直流电场作用下具有电流－刺激敏感性,表现为溶胀、收缩、弯曲行为。纤维的弯曲速度和最大弯曲度随电场强度和凝胶网络中PAA含量的增加而增大,随电解质溶液离子强度的变化出现临界最大值。纤维向负极弯曲的过程中,在电场下自由离子和反庆子迁移引起的渗透压主导作用,弯曲过程主要是溶胀弯曲;向正极弯曲过程中,由于电化学反应和电场作用下产生的PH梯度导致凝胶网络构像变化主导作用,弯曲主要是收缩弯曲;弯曲由负极向正极转化过程中,两种机理对弯曲的影响相对平衡。     

聚丙烯酸/聚丙烯酰胺水溶液复合特性的研究

通过酸度、电导率、粘度、接触角的测定,研究了聚丙烯酸 (PAA) /聚丙烯酰胺 (PAM) 水溶液复合物及复合物膜的结构和性能。结果表明,酸度、温度、浓度和复合比影响PAA/PAM的复合水溶液中大分子链的构象和流体力学体积,适度的氢键作用可以形成均相的复合溶液。经过热处理和未经热处理的聚合物膜表现出了不同的亲水性能。     

High-performance membranes for pervaporation II. Crosslinked poly(vinyl alcohol)–poly(acrylic acid) blends

Dense membranes made by crosslinking of poly(vinyl alcohol) (PVA) with poly(acrylic acid) (PAA) were prepared and tested in pervaporation and differential permeation of water–alcohol mixtures. Instead of a decrease of permeation flux as generally observed with most crosslinking agents, an increase in the permeability was observed with PAA crosslinked membranes at low PAA contents. The permeation flux increases with PAA contents in the polymer with no selectivity reduction for membranes containing less than 15 wt. % PAA. The membranes show good performances to water–2-propanol and water–ethanol mixtures, i.e. high fluxes and high selectivities to pure water. The membranes were stable and highly permeable to water. The enhancement of the permeability of PVA can be explained by a reduced crystallinity and an improved diffusivity due to the presence of PAA.     

Photo-cured pH-responsive polyampholyte-coated membranes for controlled release of drugs with different molecular weights and charges

Intelligent drug delivery membranes were synthesised by photocuring poly(acrylic acid) (PAA) or polyampholytes comprised of copolymers of acrylic acid (AA)/2-(diethylamino)ethyl methacrylate (DEAEMA) with varying monomeric compositions onto poly(2-hydroxyethyl methacrylate) (PHEMA) membranes, each with model drugs of different molecular weights and charges being incorporated. pH-responsive release behaviours of the model drugs which included methylene blue (cationic), metanil yellow (anionic) and caffeine (neutral) were studied. Only membranes with methylene blue and caffeine incorporated displayed clear pH-responsive releases though all coatings. This study demonstrates that drug diffusion through pH-responsive membranes depends to a large extent on the attractive interaction between the drug and the appropriate functional group/s in the coating.     

Fabrication and properties of a novel superabsorbent composite based on coco peat and poly (acrylic acid) cross‐linked trimethylolpropane trimaleate under ultraviolet irradiation

A series of novel poly(acrylic acid)/coco peat (PAA/CP) superabsorbent composites were prepared via the ultraviolet irradiation copolymerization of acrylic acid monomer (PAA) and coco peat cellulose (CP) in the presence of the cross‐linker trimethylolpropane trimaleate. The physico‐chemical structures of obtained PAA/CP were characterized by Fourier transform infrared spectroscopy, thermogravimetry/derivative thermogravimetry, X‐ray diffraction, and scanning electron microscopy, respectively. The critical parameters of affecting the water absorbency of PAA/CP, including the cross‐linker level, amount of CP and reaction time, were studied in detailed. The experimental results showed that the PAA/CP samples exhibited the maximum swelling value of 523.09 g/g in distilled water and 40.52 g/g in 0.9 wt % NaCl solution. The swelling behaviors of PAA/CP were significantly relied on the concentration of salt solution and the pH of external solution. The effect of ions species on the swelling performance was in the order: Na⁺ > Ca²⁺ > Fe³⁺ , and in pH 2.2 and 7.2 aqueous solutions PAA/CP composites displayed better pH‐responsiveness and reversible on‐off switching characteristics. Urea, as an agrochemical model, was loaded into PAA/CP substrate to supply with nitrogen nutrient. The test of their loading and releasing diffusion performance of urea suggested that the urea loading percentage of PAA/CP was remarkably dependent on the concentration of aqueous urea solutions and the release of urea from loaded PAA/CP samples in water followed a non‐Fickian mechanism. Owing to their considerable good water absorption capacity, slow urea release, economical and environment‐friendly merits, PAA/CP composites could be exploited for the agriculture applications. Copyright © 2016 John Wiley & Sons, Ltd.     

快速响应大孔聚(N-异丙基丙烯酰胺-co-丙烯酸)水凝胶的合成及表征

以聚乙二醇6000为成孔剂,由自由基引发N-异丙基丙烯酰胺(NIPA)和丙烯酸(AAc)共聚交联得到大孔凝胶,研究了凝胶对环境温度的响应性能.在凝胶制备过程中,PEG6000分子充当成孔剂,得到的凝胶具有大孔结构.这种大孔结构有利于水分子的进出,大孔凝胶对温度变化有较快的响应速率.增加亲水单体AAc的含量,凝胶的LCST有所升高,凝胶的亲水性增强,在较低温度下凝胶的溶胀率也随之升高.振荡实验表明,所得的大孔凝胶具有反复使用的能力.     

Drug Delivery Applications of Coaxial Electrospun Nanofibres in Cancer Therapy

Cancer is one of the most serious health problems and the second leading cause of death worldwide, and with an ageing and growing population, problems related to cancer will continue. In the battle against cancer, many therapies and anticancer drugs have been developed. Chemotherapy and relevant drugs are widely used in clinical practice; however, their applications are always accompanied by severe side effects. In recent years, the drug delivery system has been improved by nanotechnology to reduce the adverse effects of the delivered drugs. Among the different candidates, core–sheath nanofibres prepared by coaxial electrospinning are outstanding due to their unique properties, including their large surface area, high encapsulation efficiency, good mechanical property, multidrug loading capacity, and ability to govern drug release kinetics. Therefore, encapsulating drugs in coaxial electrospun nanofibres is a desirable method for controlled and sustained drug release. This review summarises the drug delivery applications of coaxial electrospun nanofibres with different structures and drugs for various cancer treatments.     

Magnetoliposomes as Potential Carriers of Doxorubicin to Tumours

Studies on magnetoliposomes (MLUV) as potential carriers for magnetic‐field‐dependent drug delivery are presented. The systems were formed with hydrophobic superparamagnetic iron oxide nanoparticles (SPIONs) confined within the bilayer of the liposomes. The nanomechanical properties of bilayer lipid membranes were evaluated and related to the amount of incorporated SPIONs. It was found that the presence of SPIONs in the lipid membrane leads to overall stiffening and increases morphological inhomogeneity, facilitating rupture of the MLUV membrane in a low‐frequency alternating magnetic field (AMF). To verify the findings, doxorubicin release from MLUVs in the presence and absence of an AMF was measured. Under experimental conditions, drug release proceeds through MLUV rupture induced by mechanical vibration of SPIONs rather than through localized heating in the vicinity of the SPIONs.     

Osteosarcoma Stem Cell Potent Gallium(III)-Polypyridyl Complexes Bearing Diflunisal

We report the anti-osteosarcoma stem cell (OSC) properties of a series of gallium(III)-polypyridyl complexes ( 5 - 7 ) containing diflunisal, a non-steroidal anti-inflammatory drug. The most effective complex within the series, 6 (containing 3,4,7,8-tetramethyl-1,10-phenanthroline), displayed similar potency towards bulk osteosarcoma cells and OSCs, in the nanomolar range. Remarkably, 6 exhibited significantly higher monolayer and sarcosphere OSC potency (up to three orders of magnitude) than clinically approved drugs used in frontline (cisplatin and doxorubicin) and secondary (etoposide, ifosfamide, and carboplatin) osteosarcoma treatments. Mechanistic studies show that 6 downregulates cyclooxygenase-2 (COX-2) and kills osteosarcoma cells in a COX-2 dependent manner. Furthermore, 6 induces genomic DNA damage and caspase-dependent apoptosis. To the best of our knowledge, 6 is the first metal complex to kill osteosarcoma cells by simultaneously inhibiting COX-2 and damaging nuclear DNA.     

Preparation and Characterization of Controlled-Release Floating Bilayer Tablets of Esomeprazole and Clarithromycin

Controlled-release effervescent floating bilayer tablets reduce dosage frequency and improve patient compliance with enhanced therapeutic outcomes. Generally, two different tablets of clarithromycin and esomeprazole, respectively, are given for the treatment of Helicobacter pylori infection and it might be worth incorporating both in a single tablet. In the current study, controlled-release floating bilayer tablets of clarithromycin and esomeprazole (F1–F4) were developed with different rates of polymeric materials by a direct compression method. During the formulation, Fourier-transform infrared spectroscopy (FTIR) analysis was performed for possible interactions between drugs and excipients. No interactions between drugs and excipients were noted. Moreover, the bilayer tablets’ thickness, diameter, friability, hardness, weight variation, dissolution, and percent purity were found within the acceptable limits. The floating lag time and total floating time of all formulations were found to be < 25 s and 24 h, respectively. The release of both the clarithromycin and esomeprazole started at the same time from the controlled-release floating bilayer tablets by anomalous non-Fickian diffusion, and the polymeric materials extended the drug release rate up to 24 h. In the case of F1, the results approached ideal zero-order kinetics. The dissolution profiles of the tested and reference tablet formulations were compared, but no significant differences were observed. It can be concluded that such controlled-release effervescent floating bilayer tablets can be efficiently used in clinical practice to reduce dosage frequency and increase patient compliance with continuous drug release for 24 h, which ultimately might enhance therapeutic efficacy.     

Hydrophilic modification of polyethersulfone membranes by low temperature plasma-induced graft polymerization

A complete and permanent hydrophilic modification of polyethersulfone (PES) membranes is achieved by argon plasma treatment followed by polyacrylic acid (PAA) grafting in vapor phase. Both Ar plasma treatment alone and post-PAA grafting rendered a complete hydrophilicity to the PES membranes. The hydrophilicity of the membranes treated with only the Ar plasmas is not, however, permanent. In contrast, the PES membranes treated with Ar plasma and subsequent acrylic acid (AA) grafting are permanently hydrophilic. High energy resolution X-ray photoelectron spectroscopy (XPS) confirmed the grafting of PAA to all surfaces of the membrane. Furthermore, water bubble point measurements remain unaffected. The pore sizes of the grafted membranes at higher grafting yield are slightly decreased. The modified membranes are less susceptible to protein fouling than the unmodified membranes and the pure water flux for the modified membranes was tremendously increased by plasma treatment. Furthermore, the modified membranes are easier to clean and required little caustic to recover permeation flux.