荧光磁性双功能树状分子微球的制备与表征

采用化学共沉淀法, 以FeCl₃·6H₂O和FeSO₄·7H₂O为原料制备了磁性Fe₃O₄纳米颗粒, 采用树状大分子对其进行修饰, 然后通过树状大分子具有的大量空腔及末端丰富的氨基, 经吸附、 键合, 与大量巯基乙酸修饰的CdSe/CdS量子点连接, 得到三代具有荧光磁性双功能的树状分子微球, 并对其进行结构表征与性能测试. 结果表明: 三代复合后的微球的平均粒径分别为15, 34和49 nm; 一代荧光磁性微球的发光性能最佳, 其量子产率达24.1%; 零代荧光磁性微球磁性能最优, 其饱和磁化强度为15.96 A·m²/kg. 这种具有荧光和磁性的双功能纳米复合微粒有望在免疫检测、 靶向治疗、 荧光追踪和磁性分离等方面得到广泛应用.     

磁性荧光纳米材料的制备与性能

采用表面活性剂3-氨丙基三乙氧基硅烷(APTES)修饰Fe₃O₄磁性纳米粒子, 经质子化后, Fe₃O₄磁性纳米粒子表面披覆大量的正电荷, 与表面带负电荷的巯基丙酸(MPA)修饰的核壳CdSe/CdS/ZnS量子点(QDs)通过强烈的静电作用而发生组装, 得到兼具磁性和荧光性能的磁性荧光纳米材料. 利用透射电子显微镜(TEM)、傅里叶变换红外光谱仪(FTIR)、X射线衍射仪(XRD)、荧光分光光度计和振动样品磁强计(VSM)等测试手段对磁性荧光纳米材料进行表征. 研究表明, 由两种粒子组装的核壳结构复合粒子拥有良好的磁性能和荧光性能.     

磁性Fe3O4纳米粒子的功能化修饰研究进展

Fe₃O₄纳米粒子因其独特的磁学性能和良好的生物相容性,在生物医药、催化剂、环境治理等领域具有良好的应用前景。然而,磁性Fe₃O₄纳米粒子易团聚、在潮湿的空气中易氧化,制约了Fe₃O₄纳米粒子的深度应用。本文结合课题组在磁性Fe₃O₄纳米粒子应用方面的研究成果,综述了磁性Fe₃O₄纳米粒子的功能化修饰,并讨论了磁性Fe₃O₄复合纳米材料发展面临的机遇和挑战。      

四氧化三铁/单壁碳纳米管磁性复合纳米粒子分散固相微萃取-高效液相色谱法测定牛奶中的香精添加剂

通过化学键合的方法制备单壁碳纳米管包覆的四氧化三铁（Fe₃O₄/CNTs）磁性复合纳米粒子。首先用水热法合成磁性Fe₃O₄纳米粒子,并进行硅烷氨基化处理,羧基化的单壁碳纳米管通过1-（3-二甲基氨基丙基）-3-乙基碳二亚胺（EDC）和N-羟基琥珀酰亚胺（NHS）交联剂反应修饰到Fe₃O₄纳米颗粒表面。合成的Fe₃O₄/CNTs复合纳米粒子具有很高的磁响应度和很好的分散能力,是一种很好的分散固相萃取剂。本研究将合成的Fe₃O₄/CNTs纳米粒子用于分散固相微萃取富集牛奶中的香精添加剂,并与高效液相色谱分析联用,实现了香兰素和乙基香兰素的快速高效富集和高灵敏度检测,两者的检出限达10 μg/L,回收率大于92%。本研究表明,合成的Fe₃O₄/CNTs磁性复合粒子是一种很好的奶制品中香兰素添加剂的样品前处理富集材料。     

磷钨酸-尿素/四氧化三铁磁性氧化脱硫催化剂反应性能

制备了铁磁性Fe₃O₄基质,并引入磷钨酸尿素复合物制备了有机硫化物氧化催化剂(HPW-Urea/Fe₃O₄),并通过IR、XRD、Raman和TG等技术手段测定了磁性催化剂的物理化学和热学性质。 研究结果表明,在Fe₃O₄上引入HPW-Urea后,磷钨酸尿素复合物以Keggin结构存在于载体Fe₃O₄上,且和载体之间是化学键作用。 在以有机硫化物乙硫醇的正己烷溶液的H₂O₂氧化反应中,磷钨酸尿素复合物的引入提高了磁性Fe₃O₄对乙硫醇的氧化活性,并探讨了尿素在活性改善中的作用。     

基于表面修饰聚丙烯酸合成超顺磁/荧光纳米复合粒子

在聚丙烯酸修饰的Fe₃O₄纳米粒子表面共价结合罗丹明B, 获得分散性和荧光信号均得到改善的超顺磁/荧光复合纳米材料. 分别用透射电子显微镜(TEM)、傅里叶变换红外光谱仪(FTIR)、热重分析仪、荧光光谱仪、X射线衍射仪(XRD) 和振动样品磁强计(VSM) 对合成的粒子进行了表征. 结果表明, 羧基化的Fe₃O₄纳米粒子和Fe₃O₄-荧光纳米复合材料的粒径基本相同, 为6～10 nm. Fe₃O₄-荧光纳米复合材料的饱和磁化强度为39.2 A•m²/kg, 室温下呈现超顺磁性, 具有较强的荧光信号.     

含有金刚烷胺的多金属氧酸盐的合成和抗流感病毒活性

以金刚烷胺和1∶10 (Ln∶W), 1∶13(Ni或Mn∶V)系列多金属氧酸盐为原料, 合成了化学式分别为K₄(C₁₀H₁₈N)₅CeW₁₀O₃₆•2H₂O (APOM-5), K₄(C₁₀H₁₈N)₅PrW₁₀O₃₆•2H₂O (APOM-6), K₃(C₁₀H₁₈N)₄NiV₁₃O₃₈•H₂O (APOM-12)和K₃(C₁₀H₁₈N)₄MnV₁₃O₃₈•H₂O (APOM-13)的四种新的多金属氧酸盐, 并通过元素分析、IR光谱及¹H NMR谱对其结构进行了表征. 在狗肾(Madin-Darby canine kidney, MDCK)细胞内, 对合成化合物进行了抗流感病毒A和B的活性研究. 发现APOM-13对流感病毒A, B两型均有明显的抑制活性, 而APOM-12只在浓度较高时对流感病毒A, B两型有抑制活性, 低浓度时, 活性不明显. APOM-5,6对A型流感病毒有效, 但对B型流感病毒抑制活性不明显. 另外发现APOM-12和APOM-13对流感病毒感染MDCK细胞病变效应(CPE)具有明显抑制作用, 且浓度越大抑制作用愈明显.     

超顺磁性Fe3O4/Au@Ag复合材料的合成及其SERS性能研究

利用溶剂热法和种子生长法分别合成Fe₃O₄磁性纳米粒子和Au@Ag核壳纳米粒子, 利用静电吸附方法成功将聚乙酰亚胺(PEI)修饰到Fe₃O₄表面并通过N-Ag共价键将Au@Ag核壳纳米粒子组装到Fe₃O₄表面, 制备Fe₃O₄/Au@Ag复合材料. 通过控制Au@Ag复合粒子的加入量, 来调节Fe₃O₄/Au@Ag复合材料的表面增强拉曼(SERS)活性. 以对巯基苯胺(p-ATP)为拉曼活性探针分子来考察该复合纳米材料的SERS性能, 检测限可以低至2×10^-9 mol/L. 同时, 将该复合材料应用于农药分子福美双的检测, 检测限可以低至10^-6 mol/L. 这种功能性复合材料既具有良好的SERS活性, 又具有Fe₃O₄磁性内核, 可以通过外加磁场实现对待测分子的分离、富集, 具有更广泛的应用前景.     

一种新型储氢材料——改性四氧化三铁的储氢性能研究

以金属Mo, Al, Cr, W可溶盐为添加物, 通过共沉淀法由FeCl₃和(NH₄)₂Fe(SO₄)₂•6H₂O的水溶液制备了单金属添加的Fe₃O₄改性储氢材料. 采用循环储氢性能评价方法, 研究了材料的储氢性能; 利用X射线粉末衍射、SEM扫描电镜和BET比表面积测试手段, 分析了材料储-放氢前后的微观结构. 结果表明: 添加了Mo金属的Fe₃O₄材料四次循环的放氢温度最低, 为310～314 ℃(放氢速率为300 μmol•min^－1•Fe-g^－1), 低于目前同类最好的储氢材料(50 ℃左右); 对材料的微观结构研究表明: 采用本文方法制备的金属添加的Fe₃O₄储氢材料其粒度大约在50～70 nm. 此外, 材料的催化活性主要与掺杂的金属类型和材料粒度的大小有关.     

羧甲基纤维素/Fe3O4复合纳米磁性材料的制备、表征及吸附性能的研究

采用改进的氧化沉淀法在羧甲基纤维素(CMC)体系中制备了以磁性纳米Fe₃O₄为核心, 外层包覆羧甲基纤维素的复合磁性纳米材料. 用透射电镜、X射线衍射、红外光谱、Zeta电位和震动样品磁强计对复合纳米Fe₃O₄进行了表面形貌、结构和磁学的表征. 在此基础上研究了复合纳米Fe₃O₄对Cu^2＋的吸附性能, 探讨了溶液pH、反应时间和 Cu^2＋的初始浓度对其吸附性能的影响. 实验结果表明, 复合Fe₃O₄粒子为反尖晶石型, 平均粒径在40 nm左右, 羧甲基纤维素在Fe₃O₄粒子表面是化学吸附, 复合Fe₃O₄粒子的饱和磁化强度为36.74 emu/g, 在中性溶液中Cu^2＋的吸附量最高, 吸附平衡时间为1.5 h, 二级动力学模型能够很好地拟合吸附动力学数据, 吸附等温数据符合Langmuir模型. 复合纳米Fe₃O₄对Cu^2＋的吸附机理主要为表面配位反应.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.