A novel spectrophotometric method for determination of cyanide using cobalt (II) phthalocyanine tetracarboxylate as a chromogen

Cobalt (II) phthalocyanine tetracarboxylate [Co (II)Pc-COOH] has been prepared and used in aqueous solutions as a novel chromogenic reagent for the spectrophotometric determination of cyanide ion. The method is based on measuring the increase in the intensity of the monomer peak in the reagent absorbance at 682 nm due to the formation of a 1 : 2 [Co (II)Pc-COOH] : [CN] complex. The complex exhibits a molar absorptivity (ε) of 7.7 × 10⁴ L mol^?1 cm^?1 and a formation constant (K_f ) of 5.4 ± 0.01 × 10⁶ at 25 ± 0.1°C. Beer's law is obeyed over the concentration range 0.15–15 µg mL^?1 (5.8 × 10^?6–5.8 × 10^?4 M) of cyanide ion, the detection limit is 20 ng mL^?1 (7.7 × 10^?7 M) the relative standard deviation is ±0.7% (n = 6) and the method accuracy is 98.6 ± 0.9%. Interference by most common ions is negligible, except that by sulphite. The proposed method is used for determining cyanide concentration in gold, silver and chromium electroplating wastewater bath solutions after a prior distillation with 1 : 1 H₂SO₄ and collection of the volatile cyanide in 1 M NaOH solution containing lead carbonate as recommended by ASTM, USEPA, ISO and APAHE separation procedures. The results agree fairly well with potentiometric data obtained using the solid state cyanide ion selective electrode.     

亚硝基R盐分光光度法测定合金钢中钴

本文改进了亚硝基R盐分光光度法测定合金钢中钴的分析方法,并详细探讨了该方法中吸收波长、缓冲溶液、氧化剂、消解酸种类、加热时间、共存离子等测定条件对结果准确度和精密度的影响.结合示差光度法,在不需分离铁、铜、镍、铬等干扰元素的条件下,可适用于测定合金钢中高含量钴,相对误差在3%以下,相对标准偏差小于1%.测定高含量钴标准...     

Second derivative spectrophotometric method for simultaneous determination of cobalt, nickel and iron using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

A simple, sensitive and rapid derivative spectrophotometric method using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) has been developed for simultaneous determination of Co(II), Ni(II) and Fe(II) which have very similar chemical behavior and appear together in many real samples. The complexes of all these metal ions with 5-Br-PADAP were formed immediately at pH 7.0 ammonium acetate buffered solution and were stable for at least 24 h. Second derivative spectra were selected for evaluation, because working wavelength determination was more precise and spectral overlap was less than in the ordinary and first derivative spectra. Three wavelengths at which the complexes exhibit extremum ²D values for Co(II), Ni(II) and Fe(II) were selected as analytical wavelengths, i.e., 640, 600 and 740 nm, respectively. Calibration curves drawn with zero-to-peak values at mentioned wavelengths were linear between 80 and 2000 ng ml⁻¹ for each metal ion. Concentrations of Co(II) and Ni(II) were calculated from the total ²D values and the sum of the linear equations for these three cations at 640 and 600 nm, after Fe(II) assay by making use of the ²D value at 740 nm. Limits of detection (LOD) for Co(II), Ni(II) and Fe(II) were 2.7, 13.9 and 3.0 ng ml⁻¹, respectively. The method has been applied to tool steel and heater resistance wire samples successfully.     

New spectrophotometric method for the determination of trace amounts of palladium

Summary A simple, rapid, selective, and sensitive method for the spectrophotometric determination of palladium is developed based on the reaction of Pd(II) with 1-amino-4-hydroxyanthraquinone (AMHA). The reaction is carried out atpH 3.8 in 50% (v/v) ethanol-water medium. The molar absorptivity of the complexed ligand is 1.1 · 10⁴ l mol^–1 cm^–1 at 620 nm. Calibration plots are linear up to 17 µg Pd cm^–3. The optimum concentration range (Ringbom plot) is between 3–14.5 µg cm^–3. The spectral study of the reaction in solutions containing equimolar concentrations or an excess of one component, in thepH range 0.3–6.5, indicate the possible complex transitions that occur in solution. Complete graphical and logarithmic analysis of the absorbance-pH graphs was performed to demonstrate and characterize the complexation equilibria in solution. Under the optimum conditions, palladium can be determined as the noncharged complex Pd(AMHA)₂ in the presence of a large number of foreign ions. Interferences caused by zirconium(IV) could be masked with fluoride ions.

---

Eine neue spektrophotometrische Methode für die Bestimmung von Palladium in Spuren

Zusammenfassung Eine einfache, schnelle und empfindliche Methode für die spektrophotometrische Bestimmung von Palladium wurde auf der Basis der Reaktion von Pd(II) mit 1-Amino-4-hydroxyanthrachinon (AMHA) entwickelt. Die Reaktion wird in 50% (v/v) Ethanol/Wasser beipH 3.8 ausgeführt. Die molare Absorption des komplexierten Liganden beträgt 1.1 · 10⁴ l mol^–1 cm^–1 bei 620 nm. Kalibrierungskurven verlaufen bis zu 17 µg Pd cm^–3 linear. Der optimale Konzentrationsbereich (Ringbom-Plot) liegt zwischen 3 und 14.5 µg cm^–3. Spektroskopische Untersuchungen der Reaktion in Lösungen, entweder mit equimolaren Konzentrationen oder mit einem Überschuß an einer Komponente impH-Bereich 0.3–6.5, lassen Rückschlüsse auf mögliche Komplex-Übergänge in Lösung zu. Es wurde eine vollständige graphische, logarithmische Analyse der Absorptions-pH-Graphen durchgeführt, um die Komplexgleichgewichte in Lösung aufzuklären und zu charakterisieren. Unter den Optimalbedingungen kann Palladium als nichtgeladener Komplex Pd(AMHA)₂ in Gegenwart einer großen Anzahl an Fremd-Ionen bestimmt werden. Schwierigkeiten mit Zirkonium(IV) konnte durch Maskierung mit Fluorid-Ionen umgangen werden.

     

聚乙二醇双水相萃取光度法测定镍

用水溶性高聚物、表面活性剂及有机物与无机盐形成的双水相体系萃取分离色素、蛋白质及测定金属离子已有报道[1-5].     

聚乙二醇双水相萃取光度法测定锌

A novel method of extraction spectrophotometric determination of Zn~(2+) in aqueous two-phase system formed by polyethylene glycol-2000,sodium sulfate and zincon has been established.Amounts of PEG solution,zincon solution,sodium sulfate added and the acidity of the system were optimized.The interference effects of various coexistent ions and the method to remove the interference were investigated.The Zn-zincon complex that had been formed in the presence of H_2BO_3-Na_2B_4O_7 buffer solution at pH 7.4 was extracted into the upper PEG-rich phase,and the absorbance of the extracted complex in the upper PEG-rich phase was measured at 630 nm.The apparent molar absorptivity was 7.3 × 10~4 L / (mol·cm).Beer's law was obeyed over the range of 0～2.0 μg / mL Zn~(2+).The analytical results obtained for Zn~(2+) in water samples were in good agreement with values measured by atomic absorption spectrometry.     

Kinetic spectrophotometric determination of trace manganese (II) with dahlia violet in nonionic microemulsion medium

A new catalytic kinetic spectrophotometric method has been developed for the determination of trace amount of manganese (II) in nonionic microemulsion medium. The method is based on the catalytic effect of manganese (II) on the oxidation of dahlia violet by potassium periodate with nitrilotriacetic acid as an activitor in the presence of nonionic microemulsion. Under the optimum conditions, the calibration graph is linear in the range of 0.0004-0.0056 μg ml⁻¹ of manganese (II) at 580 nm. The detection limit achieved is 3.75×10⁻⁵ μg ml⁻¹. Manganese (II) in foodstuff samples was determined with satisfactory results.     

Simultaneous determination of cobalt,nickel and iron by multi-wavelength spectrophotometry

A method for the simultaneous spectrophotometric determination of cobalt, nickel and iron based on the formation of their complexes with 1,5-bis(di-2-pyridylmethylene) thiocarbonohydrazide is proposed. The absorption curves of these complexes overlap severely in the scanning range 390–510 nm. The analyte concentrations are calculated by a least squares fit of the pure spectra to the mixture spectra, which therefore makes the simultaneous determination of these metallic ions possible without tedious pretreatment. The detection limits afforded by the proposed method range from 0.05 g/ml for Fe and Ni to 0.1 g/ml for Co. Root-mean-squared errors of prediction of 0.085 g/ml for Co, 0.048 g/ml for Ni and 0.1172 g/ml for Fe were obtained using the wavelength range 400–510 nm and 0.147 g/ml for Co, 0.107 g/ml for Ni and 0.127 g/ml for Fe using the wavelength range 420–434 nm. The effect of interferences is studied and the proposed method is applied to analysis for the above elements in synthetic samples and real samples, such as biological materials and alloys.     

催化褪色光度法测定痕量钴

钴是人体健康不可缺少的微量元素，本文用酸碱指示剂间甲酚紫作为指示物质，催化动力学测定结果显示间甲酚紫在pH：10．0的NH3-NH4Cl缓冲溶液中呈紫色。Co(Ⅱ)对H2O2氧化这种紫色溶液褪色反应有催化作用，从而建立了测定钴的方法。该法可直接用于维生素B12和生物样品及地下水中Co(Ⅱ)含量的测定。     

Simple flow injection method for simultaneous spectrophotometric determination of Fe(II) and Fe(III)

The method is based on spectrophotometric determination of Fe(II) and Fe(III) at a single wavelength (530 nm) with the use of a dedicated reversed-flow injection system. In the system, EDTA solution is injected into a carrier stream (HNO₃) and then merged with a sample stream containing a mixture of sulfosalicylic acid and 1,10-phenanthroline as indicators. In an acid environment (pH ≅ 3) the indicators form complexes with both Fe(III) and Fe(II), but EDTA replaces sulfosalicylic acid, forming a more stable colourless complex with Fe(III), whereas Fe(II) remains in a complex with 1,10-phenenthroline. As a result, the area and minimum of the characteristic peak can be exploited as measures corresponding to the Fe(III) and Fe(II) concentrations, respectively. The analytes were not found to affect each other's signals, hence two analytical curves were constructed with the use of a set of standard solutions, each containing Fe(II) and Fe(III). Both analytes were determined in synthetic samples within the concentration ranges of 0.05–4.0 and 0.09–6.0 mg L⁻¹, respectively, with precision less than 1.5 and 2.6% (RSD) and with accuracy less than 4.3 and 5.6% (RE). The method was applied to determination of the analytes in water samples collected from artesian wells and the results of the determination were consistent with those obtained using the ICP-OES technique.     

5-(4-Carboxylphenylazo)-8-aminoquinoline as an analytical reagent for the spectrophotometric determination of gold

The synthesis and analytical application of 5-(4-carboxylphenylazo)-8-aminoquinoline (CPAQ) are described. A simple, rapid, selective, and sensitive spectrophotometric method for the determination of microgram amounts of gold is developed, based on the colour reaction between the metal ion and CPAQ in the presence of cetyltrimethyl ammonium bromide. Gold (III) reacts with the reagent in the ratio 1 3 (metal to ligand) in alkaline solution to form a blue-green complex with an absorption maximum at 608 nm. Beer's law is obeyed over the concentration range 0–1.8 g · ml^–1 (ppm) of gold. The molar absorptivity and Sandell's sensitivity of the method are 9.11 × 10⁴ l · mole^–1 · cm^–1 and 0.00216 g · cm^–2, respectively. The interference of various ions has been studied and conditions were developed for the determination of gold in an ore and anode slimes.     

Spectrophotometric determination of aniline in aqueous solution by azo-dye formation with diazotized p-nitroaniline

A simple, sensitive, and rapid Spectrophotometric method for the trace determination of aniline in aqueous solution is described. The method is based on coupling aniline with diazotizedp-nitroaniline in the presence of ethanol and sodium hydroxide to form an intense red water-soluble azo-dye which shows maximum absorption at 505 nm and greater stability and sensitivity in the presence of cetyltrimethylammonium bromide. Beer's law is obeyed over the aniline concentration range 0.2–2.4g/ml in the solution measured; the molar absorptivity is 3.46×10⁴l· mole^–1·cm^–1, and the relative standard deviation 1–2%, depending on the aniline concentration.     

Spectrophotometric and derivative spectrophotometric determination of nickel with hydroxynaphthol blue

The reaction of nickel(II) cation with hydroxynaphthol blue (HNB) in aqueous media at pH 5.2–6.0 results in a red complex that is stable for at least 2h. Beer's Law is obeyed up to 3.2 g/ml of nickel(II) with an apparent molar absorptivity of 1.38 × 10⁴l/mol/cm at 563 nm. This paper proposes procedures for nickel determination by ordinary and first-derivative spectrophotometry. The results demonstrate that the linear dynamic range is 0.08–3.20 g/ml with a limit of detection of 23 ng/ml for ordinary spectrophotometry, compared with 21–800 ng/ml and 6 ng/ml, respectively, for first-derivative spectrophotometry. Calcium(II), magnesium(II), barium(II), strontium(II), cadmium(II), lead(II), manganese(II), bismuth(III) and molybdenum(VI) ions do not interfere for at least 1001 mass ratios. The main interferents are cobalt(II), titanium(IV), aluminium(III), mercury(II) and copper(II). The interferences of titanium(IV), aluminium(III), zirconium(IV) and iron(III) can be masked by fluoride and mercury(II) and copper(II) with thiosulfate or thiourea. The derivative method is applied to nickel determination in standard brasses and the results demonstrate that there is no significant difference between the results and certified values at the 95% confidence level.     

Structure of iron (II) and cobalt (II) bromide complexes in aqueous solution by X-ray diffraction analysis

Structures of bromo-metal complexes in concentrated aqueous solutions of FeBr₂ and of CoBr₂ were investigated by X-ray diffraction analysis. The complexes possess an octahedral geometry coordinating Br^– along with H₂O ligands. The frequency factors of metal-Br contacts per one atom of metal were 0.325 for the 2.7M (mol-dm^–3) and 0.747 for the 4.5M FeBr₂ solutions, and 0.280 for the 2.8M and 0.595 for the 4.3M CoBr₂ solutions. The frequency factors suggested that the tendency of metal ions to forming monobromo complexes is in the order, Fe>Co>Ni相似文献   

A new reagent system for the highly sensitive spectrophotometric determination of selenium

Highly sensitive and simple spectrophotometric determination of selenium is described for the determination of selenium(IV) using a new reagent leuco malachite green. The method is based on the reaction of selenium(IV) with potassium iodide in an acidic condition to liberate iodine, the liberated iodine oxidizes leuco malachite green to malachite green dye. The green coloration was developed in an acetate buffer (pH 4.2–4.9) on heating in a water bath (∼ 40 °C). The formed dye exhibits an absorption maximum at 615 nm. The method obeys Beer’s law over a concentration range of 0.04–0.4 μg mL⁻¹ selenium. The molar absorptivity and Sandell’s sensitivity of the color system were found to be 1.67 × 10⁵ L mol⁻¹ cm-¹ and 0.5 ng cm⁻², respectively. The optimum reaction conditions and other analytical parameters have been evaluated. The proposed procedure has been successfully applied to the determination of selenium in real samples of water, soil, plant material, human hair, and cosmetic samples. The results were compared to those obtained with the reference method. Statistical analysis of the results confirms the precision and accuracy of the proposed method. In addition, the developed method is cost-effective and involves easily accessible instrumentation technique which can be used by ordinary research laboratories.     

Cationic polymerization of isobutyl vinyl ether coinitiated with heteropolyacid or its salts in aqueous medium

The suspension cationic polymerization of isobutyl vinyl ether (IBVE) in aqueous medium could be achieved by using H₃PW₁₂O₄₀, AlPW₁₂O₄₀, FePW₁₂O₄₀, K₃PW₁₂O₄₀, or Na₃PW₁₂O₄₀ as efficient water‐tolerant coinitiators in the presence of HCl. The addition reaction of IBVE with H₂O occurred to form IBVE–H₂O adduct and then subsequent decomposition immediately took place or turned to acetaldehyde diisobutyl acetal (A) in the presence of AlPW₁₂O₄₀, and ( A ) decomposed rapidly to form 2‐isobutanol ( B ) and acetaldehyde ( C ). Cationic polymerization of IBVE in aqueous medium was promoted greatly with increasing HCl concentration and proceeded extremely rapidly to get high polymer yield even at low concentration of AlPW₁₂O₄₀ of 0.3 mM. A sufficient amount of HCl was needed to decrease the hydrolysis of initiator IBVE–HCl and to accelerate the polymerization in aqueous medium simultaneously. The yield and molecular weight of poly(IBVE) increased with increasing concentrations of HCl and AlPW₁₂O₄₀ or with decreasing temperature. The isotactic‐rich poly(IBVE)s with m diad of around 60%, having M_n of 1200–4500 g mol^?1 and monomodal molecular weight distribution could be obtained via cationic polymerization of IBVE in aqueous medium. This is the first example of cationic polymerization of IBVE in aqueous medium coinitiated by heteropolyacid and its salts. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Spectrophotometric determination of 1-naphthylamine in urine with pentacyanonitrosylmanganate (II)

A new Spectrophotometric method is proposed for the determination of 1-naphthylamine (R), based on its reaction with Mn(CN)₅NO^2– to form Mn(CN)₅NH₂R^3– and measurement of the absorbance at 472 nm. In aqueous medium the molar absorptivity of the manganese complex is maximum ( = 8.0 × 10³1 · mole^–1 ·cm^–1) in the pH range 5.0–10.0, the colour develops more rapidly at pH 10.0. The absorptivity is increased by a factor of 3.5 if the complex is extracted as an ion-associate into chloroform. The extraction efficiency is 99.2% for a single-step extraction, and a concentration factor of 5 can also be achieved. Linearity of response extends over the range 0.04–1.4 gmg/ml 1-naphthylamine, the coefficient of variation being 1.4% at the 0.29 g/ml level (n = 6). The detection and determination limits are 0.005 and 0.018 g/ml, respectively. The method is selective enough to allow the determination of 1-naphthylamine in the presence of considerable amounts of other amines, such as aminophenols and phenylenediamines. Results obtained in the determination of 1-naphthylamine in human urine were very satisfactory.     

A simple and selective flow-injection spectrophotometric determination of copper(II) by using acetylsalicylhydroxamic acid

A new simple, and rapid flow-injection spectrophotometric method is developed for the determination of trace amounts of Cu(II) by using a new chromogenic reagent acetylsalicylhydroxamic acid (AcSHA). The method is based on the formation of colored Cu(II)-(AcSHA)₂ complex. The optimum conditions for the chromogenic reaction of Cu(II) with AcSHA is studied and the colored (green) complex is selectively monitored at λ_max 700 nm. With the reagent carrier solvent (dimethylsulfoxide (DMSO) and acetate buffer, pH 4.2) flow-rate of 1 ml min⁻¹, a detection limit (2S) of 1 μg l⁻¹ Cu(II) was obtained at a sampling rate of 80 sample h⁻¹. The calibration graph was linear in the Cu(II) concentration range 5-120 μg l⁻¹. The relative standard deviation (n=10) was 0.64% for a sample containing 60 μg l⁻¹ Cu(II). The detailed study of various interferences confirmed the high selectivity of the developed method. The method was successfully applied to determine trace amounts of copper(II) in river and seawater samples. The accuracy of the method was demonstrated by the analysis of standard reference materials C12X3500 and C14XHS 50.     

Solid-phase UV spectrophotometric method for determination of ciprofloxacin

A simple and inexpensive method for the determination of ciprofloxacin has been developed using solid-phase spectrophotometry. The intrinsic absorbance of ciprofloxacin fixed on a dextran-type cation-exchange resin, Sephadex SP C-25, was measured directly at 277 and 380 nm after packing the gel beads in a 1-mm cell. Using a sample volume of 10 ml, the calibration graph was linear over the range 0.05-0.3 μg ml⁻¹ with a R.S.D. of 1.11% (n=8). The sensitivity obtained is 40 times higher than that of the corresponding solution method. The method was applied to the determination of ciprofloxacin in pharmaceutical preparations and was validated by standard addition.     

N-Alkylation of 4-nitro-1,2,3-triazole revisited. Detection and characterization of the N3-ethylation product, 1-ethyl-5-nitro-1,2,3-triazole

The products of the alkylation of sodium 4-nitro-1,2,3-triazolate with ethyl bromide were investigated using ¹H, ¹³C, and ¹⁵N NMR spectroscopy. It was found that alkylation proceeds on the triazole nitrogen atoms giving a mixture of three isomeric N-ethyl-4-nitro-1,2,3-triazoles. The molar ratio of N1, N2, and N3-alkylation products was 4:8:1. The formation of a minor N3-isomer, namely 1-ethyl-5-nitro-1,2,3-triazole was confirmed by X-ray structural analysis of single crystals of its tetranuclear copper(II) complex obtained by reaction of copper(II) chloride dihydrate with a mixture of the N2 and N3-isomers.