Ag/C包覆对Li[Li0.2Mn0.54Ni0.13Co0.13]O2电化学性能的影响

运用共沉淀和元素化学沉积相结合的方法,制备出了具有Ag/C包覆层的层状富锂固溶体材料Li[Li0.2Mn0.54Ni0.13Co0.13]O2.通过X射线衍射(XRD)、场发射扫描电子显微镜(SEM)、透射电子显微镜(TEM)、恒流充放电、循环伏安(CV),电化学阻抗谱(EIS)和X射线能量散射谱(EDS)方法,研究了Ag/C包覆层对Li[Li0.2Mn0.54Ni0.13Co0.13]O2电化学性能的影响.结果表明,Ag/C包覆层的厚度约为25 nm,Ag/C包覆在保持了固溶体材料α-NaFeO2六方层状晶体结构的前提下,显著地改善了Li[Li0.2Mn0.54Ni0.13Co0.13]O2的电化学性能.在2.0-4.8 V(vs Li/Li+)的电压范围内,首次放电(0.05C)容量由242.6 mAh·g-1提高到272.4 mAh·g-1,库仑效率由67.6%升高到77.4%;在0.2C倍率下,30次循环后,Ag/C包覆的电极材料容量为222.6 mAh·g-1,比未包覆电极材料的容量高出14.45%;包覆后的电极材料在1C下的容量仍为0.05C下的81.3%.循环伏安及电化学交流阻抗谱研究表明,Ag/C包覆层抑制了材料在充放电过程中氧的损失,有效降低了Li[Li0.2Mn0.54Ni0.13Co0.13]O2颗粒的界面膜电阻与电化学反应电阻.     

Ag/C包覆对Li[Li0.2Mn0.54Ni0.13Co0.13]O2电化学性能的影响

运用共沉淀和元素化学沉积相结合的方法,制备出了具有Ag/C包覆层的层状富锂固溶体材料Li [Li0.2Mn0.54Ni0.13Co0.13]O2.通过X射线衍射(XRD)、场发射扫描电子显微镜(SEM)、透射电子显微镜(TEM)、恒流充放电、循环伏安(CV),电化学阻抗谱(EIS)和X射线能量散射谱(EDS)方法,研究了Ag/C包覆层对Li[Li0.2Mn0.54Ni03Co013]O2电化学性能的影响.结果表明,Ag/C包覆层的厚度约为25 nm,Ag/C包覆在保持了固溶体材料α-NaFeO2六方层状晶体结构的前提下,显著地改善了Li[Li0.0Mn054Ni0.13Co013]O2的电化学性能.在2.0-4.8 V (vs Li/Li+)的电压范围内,首次放电(0.05C)容量由242.6 mAh·g-1提高到272.4 mAh·g-1,库仑效率由67.6％升高到77.4％;在0.2C倍率下,30次循环后,Ag/C包覆的电极材料容量为222.6 mAh·g-1,比未包覆电极材料的容量高出14.45％;包覆后的电极材料在1C下的容量仍为0.05C下的81.3％.循环伏安及电化学交流阻抗谱研究表明,Ag/C包覆层抑制了材料在充放电过程中氧的损失,有效降低了Li[Li02Mn0.54Ni0.13Co013]O2颗粒的界面膜电阻与电化学反应电阻.     

锂离子电池正极材料Li_(1.2)Mn_(0.54-x)Ni_(0.13)Co_(0.13)Zr_xO_2的制备及电化学性能

为了改善富锂锰基正极材料Li1.2Mn0.54Ni0.13Co0.13O2的循环性能,采用燃烧法合成了正极材料Li1.2Mn0.54-xNi0.13Co0.13ZrxO2(x=0.00,0.01,0.02,0.03,0.06).通过X射线衍射(XRD)和扫描电镜(SEM)对其结构与形貌进行了表征,利用恒电流充放电测试,循环伏安(CV)及电化学交流阻抗谱(EIS)技术对其电化学性能进行测试.结果表明,Li1.2Mn0.54-xNi0.13Co0.13ZrxO2(x=0.00,0.01,0.02,0.03,0.06)正极材料均具有α-NaFeO2型层状结构;在室温,2.0-4.8 V电压范围,以0.1C和1.0C(充放电电流以1.0C=180 mA·g-1计算)倍率充放电进行测试,样品Li1.2Mn0.52Ni0.13Co0.13Zr0.02O2的首次放电比容量分别为280.3和206.4 mAh·g-1.其中,在1.0C倍率下,100次循环后容量保持率由原来的73.2%提高到88.9%;以5.0C倍率充放电进行测试,经50次循环后,掺杂正极材料的放电比容量为76.5 mAh·g-1,而未掺杂材料仅有15.0 mAh·g-1.在50、25和-10°C,2.0C倍率条件下,掺杂正极材料的电化学性能均得到有效改善,其中,在-10°C经过50次循环后正极材料Li1.2Mn0.52Ni0.13Co0.13Zr0.02O2比未掺杂的正极材料相比,其放电比容量提高了61.1%.     

碳酸盐共沉淀法制备Li[Li0.2Co0.13Ni0.13Mn0.54]O2中加料方式对产物性能的影响

采用碳酸钠和碳酸氢铵作为沉淀剂和络合剂,在水溶液中共沉淀Mn2+、Ni2+和Co2+以获得混合过渡金属元素的碳酸盐沉淀前驱体Mn0.675Ni0.1625Co0.1625CO3。并进一步合成高容量锂离子电池正极材料Li[Li0.2Co0.13Ni0.13Mn0.54]O2。考察了3种不同加料方式对共沉淀前驱体的结构、形貌和元素比例的影响,以及对最终产物的结构、形貌和电化学性能的影响。     

溶胶凝胶法合成富锂正极材料Li[Li0.2Ni0.2Mn0.6]O2及性能表征

以LiOH.H2O、Mn(CH3COO)2.4H2O和Ni(CH3COO)2.4H2O为原料,分别用柠檬酸(CA)与乙二胺四乙酸(EDTA)为配位剂,采用溶胶凝胶法结合固相烧结法制备富锂固溶体正极材料Li[Li0.2Ni0.2Mn0.6]O2。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、激光粒度仪对所得样品的结构、形貌、粒径分布进行了表征,并测试了材料的电化学性能。采用CA配位制备的材料的电化学性能优于用EDTA配位制备的材料的电化学性能,室温下以18 mA.g-1的电流密度,在2.0~4.8 V电压范围内充放电,用CA制备的材料首次充电比容量高达324 mAh.g-1,首次库伦效率达82%;在180 mA.g-1的电流下,其可逆比容量保持在120 mAh.g-1。     

溶液处理富锂锰基固溶体Li_1.2Mn_0.54Ni_0.13Co_0.13O_2

针对Li1.2Mn0.54Ni0.13Co0.13O2材料的首次效率过低和倍率性能差的缺陷,系统研究了中性去离子水、弱酸性的硫酸铵和强酸性的磷酸3种不同pH值的溶液处理对Li[Li0.2-Mn0.54Ni0.13Co0.13]O2综合性能的影响.ICP结果表明预处理液的pH值对Li的析出量有显著影响;XRD结果显示处理对材料的体相结构有影响;XPS证实处理对材料表面过渡金属元素的价态没有影响.充放电测试表明,硫酸铵处理后的样品具有最优的电化学性能,首次效率由64.6%提高到85.4%,1 C放电容量从149.5 mA h g?1提高到183.7 mA h g?1,中值电压呈缓和下降趋势.     

富锂正极材料Li[Li0.2Mn0.4Fe0.4]O2的表面包覆改性

用共沉淀法合成了富锂正极材料Li[Li0.2Mn0.4Fe0.4]O2,并对其表面进行Al2O3包覆。采用XRD、SEM和电化学测试等方法对样品进行表征。结果表明,与Li[Li0.2Mn0.4Fe0.4]O2相比,包覆改性后的Li[Li0.2Mn0.4Fe0.4]O2具有较好的电化学性能,其初始放电容量未明显降低,而循环寿命大大提高,4.0%Al2O3包覆处理的富锂正极材料经50次充放电循环后,容量衰减量在9%左右。     

AlF3包覆对Li1.2Mn0.534Ni0.133Co0.133O2正极材料电化学性能的影响

通过共沉淀法制备锂离子电池富锂锰基正极材料Li1.2Mn0.534Ni0.133Co0.133O2,并对其进行AlF3包覆。实验结果表明,通过AlF3包覆,材料的电化学性能得到明显提高。在0.2C下,包覆前材料的首次放电比容量为253 mAh.g-1,首次充放电效率仅为88.8%。经过AlF3包覆,材料的首次放电比容量提高到294 mAh.g-1,首次充放电效率高达96.4%。同样,在1.0C下循环50次,未包覆材料的放电比容量由225 mAh.g-1降到185 mAh.g-1,容量保持率仅为82.2%。经过AlF3包覆,材料的放电比容量由230mAh.g-1仅降为222 mAh.g-1,容量保持率高达96.5%。     

锂离子电池正极材料Li[Li0.2Ni0.2Mn0.6]O2的酸浸改性研究

为提高锂离子电池正极材料Li[Li0.2Ni0.2Mn0.6]O2的首次充放电效率,对固相法合成的该材料进行了酸浸的改性研究。通过X射线衍射(XRD)、扫描电子显微镜(SEM)对所得样品的结构、形貌进行了表征。结果表明,Li[Li0.2Ni0.2Mn0.6]O2经过酸处理后,首次放电效率得到了较大的提高,但是放电中值电压明显下降。其中,0.5 mol.L-1的硝酸浸泡5 h的效果最佳,首次放电效率达到了86.7%,同时放电容量达到最大值的循环次数大大减少。酸浸改性的原因被归结于材料表面出现了富锂尖晶石结构Li4Mn5O12相。     

梯度包覆镍酸锂材料Li[Ni0.92Co0.04Mn0.04]O2的合成与研究

采用浓度梯度加料的方式,首先沉淀制备了核为Ni(OH)2、壳为镍钴锰氢氧化物浓度梯度包覆的复合前驱体,然后配锂高温焙烧,合成了梯度包覆的镍酸锂复合正极材料Li[Ni0.92Co0.04Mn0.04]O2。采用X射线衍射(XRD)、扫描电镜(SEM)、恒电流充放电测试等方法对材料的结构、表观形貌及电化学性能进行了表征。结果表明,该材料具有良好的六方单相层状α-NaFeO2结构,呈类球型状。切面元素线扫描显示该材料的包覆壳层中主要金属元素呈梯度变化。同时该新型梯度包覆的镍酸锂复合正极材料表现出了优越的电化学性能:在25℃下,2.8~4.3 V充放电范围,0.1C首次放电比容量可达198.3 mAh.g-1,循环40次容量保持96.8%;1C和2C倍率下放电比容量可达175 mAh.g-1和165.1 mAh.g-1。55℃下,该材料首次放电比容量可达236.1 mAh.g-1,循环40次容量仍能保持77.5%。     

Ag/C包覆对Li[Li0.2Mn0.54Ni0.13Co0.13]O2电化学性能的影响

运用共沉淀和元素化学沉积相结合的方法,制备出了具有Ag/C 包覆层的层状富锂固溶体材料Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂. 通过X 射线衍射（XRD）、场发射扫描电子显微镜（SEM）、透射电子显微镜（TEM）、恒流充放电、循环伏安（CV）,电化学阻抗谱（EIS）和X 射线能量散射谱（EDS）方法,研究了Ag/C 包覆层对Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂电化学性能的影响. 结果表明,Ag/C 包覆层的厚度约为25 nm,Ag/C 包覆在保持了固溶体材料α-NaFeO₂ 六方层状晶体结构的前提下,显著地改善了Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ 的电化学性能. 在2.0-4.8 V（vs Li/Li⁺）的电压范围内,首次放电（0.05C）容量由242.6 mAh·g^-1提高到272.4 mAh·g^-1,库仑效率由67.6%升高到77.4%;在0.2C倍率下,30 次循环后,Ag/C 包覆的电极材料容量为222.6 mAh·g^-1,比未包覆电极材料的容量高出14.45%;包覆后的电极材料在1C下的容量仍为0.05C下的81.3%. 循环伏安及电化学交流阻抗谱研究表明,Ag/C包覆层抑制了材料在充放电过程中氧的损失,有效降低了Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂颗粒的界面膜电阻与电化学反应电阻.     

Sn-doped Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode materials for lithium-ion batteries with enhanced electrochemical performance

Sn-doped Li-rich layered oxides of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ have been synthesized via a sol-gel method, and their microstructure and electrochemical performance have been studied. The addition of Sn⁴⁺ ions has no distinct influence on the crystal structure of the materials. After doped with an appropriate amount of Sn⁴⁺, the electrochemical performance of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ cathode materials is significantly enhanced. The optimal electrochemical performance is obtained at x = 0.01. The Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode delivers a high initial discharge capacity of 268.9 mAh g^?1 with an initial coulombic efficiency of 76.5% and a reversible capacity of 199.8 mAh g^?1 at 0.1 C with capacity retention of 75.2% after 100 cycles. In addition, the Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode exhibits the superior rate capability with discharge capacities of 239.8, 198.6, 164.4, 133.4, and 88.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively, which are much higher than those of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ (196.2, 153.5, 117.5, 92.7, and 43.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively). The substitution of Sn⁴⁺ for Mn⁴⁺ enlarges the Li⁺ diffusion channels due to its larger ionic radius compared to Mn⁴⁺ and enhances the structural stability of Li-rich oxides, leading to the improved electrochemical performance in the Sn-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ cathode materials.     

Origin of the irreversible plateau (4.5 V) of Li[Li0.182Ni0.182Co0.091Mn0.545]O2 layered material

Layered LiNi_0.4Co_0.2Mn_0.4O₂, Li[Li_0.182Ni_0.182Co_0.091Mn_0.545]O₂, Li[Li_1/3Mn_2/3]O₂ powder materials were prepared by rheological phase method. XRD characterization shows that these samples all have analogous structure to LiCoO₂. Li[Li_0.182Ni_0.182Co_0.091Mn_0.545]O₂ can be considered to be the solid solution of LiNi_0.4Co_0.2Mn_0.4O₂ and Li[Li_1/3Mn_2/3]O₂. Detailed information from XRD, ex situ XPS measurement and electrochemical analysis of these three materials reveals the origin of the irreversible plateau (4.5 V) of Li[Li_0.182Ni_0.182Co_0.091Mn_0.545]O₂ electrode. The irreversible oxidation reaction occurred in the first charging above 4.5 V is ascribed to the contribution of Li[Li_1/3Mn_2/3]O₂ component, which maybe extract Li⁺ from the transition layer in Li[Li_1/3Mn_2/3]O₂ or Li[Li_0.182Ni_0.182Co_0.091Mn_0.545]O₂ through oxygen release. This step also activates Mn⁴⁺ of Li[Li_1/3Mn_2/3]O₂ or Li[Li_0.182Ni_0.182Co_0.091Mn_0.545]O₂, it can be reversibly reduced/oxidized between Mn⁴⁺ and Mn³⁺ in the subsequent cycles.     

Study of carbon surface-modified Li[Li0.2Mn0.54Ni0.13Co0.13]O2 for high-capacity lithium ion battery cathode

Carbon surface-modified Li-excess layered oxide solid solution Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ cathode is fabricated through a liquid phase route using polyvinylpyrrolidone as carbon source. X-ray diffraction and X-ray photoelectron spectroscopy indicate that the crystal structure and the chemical states of elements for Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ are kept after carbon surface treatment. The high-resolution transmission electron microscopy demonstrated the existence of very little carbon on the surface and the clear boundary after carbon treatment. The carbon surface-modified sample delivers a discharge capacity of 293.2 mAh?g^?1 at C/10 rate (suppose 1 C rate?=?250 mA?g^?1) and 191.6 mAh?g^?1 at 1 C rate between 2.0 and 4.8 V; the capacity retention rate is ～86 % after 70 cycles at 1 C rate. Superior electrochemical properties can be contributed to the carbon surface modification in these aspects including minimizing nanoparticle aggregation and cell polarization, increasing the electronic conductivity, suppressing the elimination of oxide ion vacancies, as well as suppressing the formation of the thick solid electrolyte interfacial layer. Moreover, the annealing process of carbon surface modification might be able to consume Li₂CO₃ impurity partly and cause the recrystallization of the surface disordered layer.     

球磨辅助高温固相法制备Li1.0Na0.2Ni0.13Co0.13Mn0.54O2正极材料及其性能

以乙酸盐(乙酸锂、乙酸钠、乙酸钴、乙酸镍、乙酸锰等)为原材料,采用球磨辅助高温固相法制备Li_1.0Na_0.2Ni_0.13Co_0.13Mn_0.54O₂正极材料。借助XRD、SEM等表征材料的结构和形貌,利用循环伏安、恒流充放电、交流阻抗等方法研究材料的电化学性能。结果表明,钠的掺杂导致颗粒表面光滑度降低,形成Na_0.77MnO_2.05新相。0.05C活化过程中,掺钠样品和未掺钠样品首次放电比容量分别为258.4 mAh·g^-1和215.8 mAh·g^-1,库伦效率分别为75.2%和72.8%;2C放电比容量分别为116.3 mAh·g^-1和106.2 mAh·g^-1。研究发现,掺钠可减小首次充放电过程的不可逆容量,提高容量保持率;改善倍率性能与容量恢复特性;降低SEI膜阻抗和电荷转移阻抗;掺钠后样品首次循环就可以基本完成Li₂MnO₃组分向稳定结构的转化,而未掺杂的样品需要两次循环才能逐步完成该过程;XPS结果表明,掺钠样品中Ni²⁺、Co³⁺、Mn⁴⁺所占比例明显提高,改善了样品的稳定性和电化学性能;循环200次后的XRD结果表明掺钠与未掺钠材料在脱嵌锂反应中的相变化过程基本一致,良好有序的层状结构遭到破坏是循环过程中容量衰减的主要原因。     

锂离子电池正极材料Li1.2Mn0.54-xNi0.13Co0.13ZrxO2的制备及电化学性能

为了改善富锂锰基正极材料Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ 的循环性能,采用燃烧法合成了正极材料Li_1.2Mn_0.54-xNi_0.13Co_0.13Zr_xO₂（x=0.00,0.01,0.02,0.03,0.06）. 通过X射线衍射（XRD）和扫描电镜（SEM）对其结构与形貌进行了表征,利用恒电流充放电测试,循环伏安（CV）及电化学交流阻抗谱（EIS）技术对其电化学性能进行测试. 结果表明,Li_1.2Mn_0.54-xNi_0.13Co_0.13Zr_xO₂（x=0.00,0.01,0.02,0.03,0.06）正极材料均具有α-NaFeO₂型层状结构;在室温,2.0-4.8 V电压范围,以0.1C和1.0C（充放电电流以1.0C=180 mA·g^-1计算）倍率充放电进行测试,样品Li_1.2Mn_0.52Ni_0.13Co_0.13Zr_0.02O₂的首次放电比容量分别为280.3 和206.4 mAh·g^-1. 其中,在1.0C倍率下,100次循环后容量保持率由原来的73.2%提高到88.9%;以5.0C倍率充放电进行测试,经50次循环后,掺杂正极材料的放电比容量为76.5 mAh·g^-1,而未掺杂材料仅有15.0 mAh·g^-1. 在50、25 和-10 ℃,2.0C倍率条件下,掺杂正极材料的电化学性能均得到有效改善,其中,在- 10℃ 经过50 次循环后正极材料Li_1.2Mn_0.52Ni_0.13Co_0.13Zr_0.02O₂比未掺杂的正极材料相比,其放电比容量提高了61.1%.