含硅磷杂化物环氧树脂固化物性能研究

首先用γ-环氧丙氧基三甲氧基硅烷(KH-560)和亚磷酸二乙酯(DEP)反应的中间产物进行水解缩合反应,合成了一种含磷低聚硅氧烷杂化物.并用FTIR,NMR,GPC对其结构及分子量进行了表征.然后将含磷低聚硅氧烷引入到双酚A环氧树脂(E-54)制备硅磷杂化物环氧树脂的固化物.对这种含硅磷杂化物环氧树脂固化物的性能研究发现其极限氧指数为23～29,DSC分析结果玻璃化转变温度(Tg)可以达到204℃,失重5%的温度(Td)5%比纯E-54提高近20℃.该固化物具有阻燃性能,同时具有较好的热性能。     

聚苯基硅氧烷与聚甲基苯基硅氧烷改性环氧树脂的合成与性能比较

热熔法制备了一系列聚苯基甲氧基硅氧烷(PPMS)、聚甲基苯基甲氧基硅氧烷(PMPS)改性环氧树脂,通过环氧值、红外光谱(IR)分析表明聚硅氧烷接枝了E-20环氧树脂且环氧基保持不变.探讨了有机硅含量对改性树脂固化体系耐热性能及韧性的影响.实验表明,当E-20环氧树脂与PPMS、PMPS的质量比为7∶3时,改性树脂固化体系的耐热性能明显提高,玻璃化转变温度(Tg)为95.8、88.3℃,分别比改性前提高了9.0℃和1.5℃;质量损失50%时的热分解温度(Td)为476.5、487.8℃,分别比改性前提高了58.3℃和69.5℃.与ED-30固化体系相比,EPMS-30固化物的耐热性能,韧性等力学性能提高的更加明显,并且还具有优良的涂膜性能.     

环氧基笼型倍半硅氧烷/4,4'-二氨基二苯砜体系的等温固化动力学

应用等温差示扫描量热法研究了4,4'-二氨基二苯砜(DDS)固化笼型倍半硅氧烷环氧树脂(POSSER)体系的反应动力学,测定了固化反应热,得出了不同温度下固化反应程度与反应时间、固化反应速率与反应时间的关系曲线,通过非线性拟合得到固化反应速率与反应程度的关系曲线.结果表明,固化反应在体系的玻璃化转变温度以上进行,等温固化反应遵从自催化反应机理,用Kamal方程可很好地描述不同温度下固化反应的自催化过程,拟合得到其反应动力学参数k1、k2、m、n,k1和k2对应的固化反应的表观活化能分别为79.67和59.84 kJ/mol.     

环氧树脂共混物相结构的调控方法研究

研究了环氧树脂(E51)/聚砜(PSF)共混物相结构的控制方法.通过抑制相分离、控制预固化的反应程度控制环氧树脂的分子量,固化后可获得不同的共混物相结构.依据红外测定的固化反应程度设定固化程序,可有效控制共混物的相结构.加入促进剂三氟化硼-乙基胺(BTF-EA)可提高固化反应速度,使相分离结构在早期被抑制,以获得小微区的相结构.     

电子束辐射固化环氧树脂的动态力学分析——树脂化学结构、分子量及其分布的影响

应用不同化学结构、分子量及其分布的环氧树脂进行了电子束辐射固化实验 ,对固化物进行了动态力学分析 ,研究了不同样品凝胶含量、内耗tanδ及动态模量的变化规律 .分析结果表明环氧树脂辐射反应活性与其化学结构有很大关系 ,酚醛型环氧树脂的辐射反应活性高 ,固化后高温模量及玻璃化温度较高 ,而脂环族环氧树脂反应活性小 .在低辐射剂量下 ,环氧树脂的固化度随分子量增大略有下降 ,但固化物的玻璃化温度随分子量增加而升高 .增大辐射剂量 ,树脂固化度的提高受分子量大小的影响很小 ,分子量较大样品的网络均匀程度有所提高 ,在较高反应程度下 ,玻璃化温度主要受固化度影响 .树脂固化程度也是决定其模量高低的主要因素 ,而在固化程度相近的情况下 ,分子量的影响作用很大 .在同样辐射剂量下 ,分子量分布宽的树脂固化反应程度高 ,但交联网络均匀性低 .     

含硅氧烷结构聚酰亚胺树脂的耐热稳定性及高温结构演变

基于含硅芳香二胺双(4-氨基苯氧基)二甲基硅烷(APDS)设计制备了系列苯乙炔基封端的含硅氧烷结构聚酰亚胺树脂预聚物(PEPA-PIS), 考察了硅氧烷含量对树脂固化物耐热稳定性的影响规律. 利用非反应性苯酐基团封端的模型预聚物(PA-PIS)证明了温度对于硅氧烷结构演变的影响. 通过对树脂固化物高温固化处理后耐热稳定性与微观结构和表面形貌的关系进行深入研究, 发现在高温下硅氧烷结构发生氧化交联反应, 并在树脂表面形成具有无机特性的二氧化硅结构, 这种有机/无机杂化特性可显著提高聚酰亚胺树脂的耐热稳定性.     

含硅芳二胺固化环氧树脂的反应动力学研究

合成了2种含硅二胺单体3,3'-(1,3-二甲基-1,3-二乙烯基-1,3-二硅氧烷)二苯胺(S1)和4,4'-(1,3-二甲基-1,3-二乙烯基-1,3-二硅氧烷)二苯胺(S2),并对其作为环氧树脂的新型固化剂进行了研究.采用非等温示差扫描量热技术(DSC)研究了其与双酚A型环氧树脂E51体系的固化反应动力学,根据不同升温速率下E51/S1和E51/S2体系的特征温度的变化,分别确定了该两体系的固化反应工艺条件,即:E51/S1体系为100℃/1h+160℃/2h+190℃/3h;E51/S2体系为110℃/1h+170℃/2h+190℃/3h.通过Kissinger方程、Crane方程以及Arrheninus方程对固化反应进行了固化动力学行为研究,得到了两个反应体系的表观活化能ΔE、Arrhenius因子A以及反应级数n等动力学参数.E51/S1体系的ΔE为50.65 k J/mol、A为1.83×105,n为0.87;E51/S2体系的ΔE为51.39 k J/mol,A为1.44×105,n为0.87,由ΔE和A表明,E51和S2的反应活性高于E51和S1的反应活性,即,氨基位于苯环的间位时与环氧基团更容易反应.二者的反应级数相同并且小于1,说明E51与S1和S2之间的反应是复杂反应.在动力学参数的基础上,得到了n级固化动力学模型.     

环氧基笼型倍半硅氧烷/4，4′-二氨基二苯砜体系的等温固化动力学

笼型倍半硅氧烷环氧树脂;二氨基二苯砜;固化反应动力学;差示扫描量热法     

动态固化聚丙烯/环氧树脂共混物的研究

将动态硫化技术应用于热塑性树脂 热固性树脂体系 ,制备了动态固化聚丙烯 (PP) 环氧树脂共混物 .研究了动态固化PP 环氧树脂共混物中两组分的相容性、力学性能、热性能和动态力学性能 .实验结果表明 ,马来酸酐接枝的聚丙烯 (PP g MAH)作为PP和环氧树脂体系的增容剂 ,使分散相环氧树脂颗粒变细 ,增加了两组分的界面作用力 ,改善了共混物的力学性能 .与PP相比 ,动态固化PP 环氧树脂共混物具有较高的强度和模量 ,含 5 %环氧树脂的共混物拉伸强度和弯曲模量分别提高了 30 %和 5 0 % ,冲击强度增加了 15 % ,但断裂伸长率却明显降低 .继续增加环氧树脂的含量 ,共混物的拉伸强度和弯曲模量增加缓慢 ,冲击强度无明显变化 ,断裂伸长率进一步降低 .动态力学性能分析 (DMTA)表明动态固化PP 环氧树脂共混物是两相结构 ,具有较高的储能模量 (E′)     

咪唑固化不同类型环氧树脂的固化特征、固化动力学及其反应活性

以咪唑为固化剂,对缩水甘油醚型、缩水甘油酯型环氧树脂(简称链型环氧树脂)及脂环环氧树脂的固化特征、固化动力学及反应活性进行了研究.DSC实验结果表明,固化过程均分两阶段进行,链型环氧树脂固化反应表观活化能低于脂环环氧树脂.各树脂第一阶段的表观反应活化能均低于第二阶段活化能.当脂环环氧树脂中混入不同比例的链型环氧树脂后,固化反应速率均较脂环环氧树脂单独固化时快,当链型环氧树脂量大于50％时,更为明显.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.