化学沉积法制备Ni-P纳米线与纳米管有序阵列

以多孔氧化铝膜为模板, 在室温下的酸性化学镀镍槽中通过化学沉积法生长出纳米线与纳米管有序阵列. 分别用X射线衍射仪(XRD)与透射电子显微镜(TEM)对纳米线、纳米管阵列进行表征. 并通过对纳米线与纳米管的生长方式进行分析比较, 系统地研究了多孔氧化铝模板的前处理对纳米阵列生长的影响. 结果表明, 生成的纳米线与纳米管均为非晶态的镍磷合金. 室温下镍纳米管的生成主要取决于敏化、活化过程, 而当纳米管的厚度达到一定程度后就不再随时间变化.     

阳极氧化铝模板法可控制备金属纳米线和纳米管阵列的生长机制

利用阳极氧化铝模板(AAO)进行Ni的电化学沉积, 通过在溶液中引入螯合剂控制电解质的有效浓度和电沉积的过电位, 实现了Ni纳米线和纳米管阵列的可控制备. 通过分析电沉积过程中纳米线和纳米管在不同位置生长速率(侧壁(Vw)和底端(Vb))的控制因素, 我们提出了纳米线和纳米管生长的可能机制. 当电解质浓度高而还原电位更负(如-1.5 V)时, 或者当电解质浓度低而还原电位较负(如-0.5 V)时, Vw>Vb, 可以获得Ni纳米管阵列; 当电解质浓度高而还原电位较负(如-0.5 V)时, 或者当电解质浓度低而还原电位更负(如-1.5 V)时, Vw≈Vb, 可以获得Ni纳米线阵列. 这种生长机制适用于多种金属纳米管或者纳米线阵列的可控制备.     

大长径比有序多孔阳极氧化铝模板的制备及用于镍纳米线阵列

报道一种恒电流二次氧化制备大长径比(>1000)阳极氧化铝(AAO)模板的方法,研究氧化时间和氧化电流密度分别对制备的AAO模板的表面形貌、孔径大小、厚度等的影响.结果表明,AAO模板的表面形貌及厚度n受m氧、厚化度电约流为密2度00及μ氧m、化长时径间比的为影10响0;-当13氧00化的电高流质密量度A为AO8模m板A·.c采m用-2电时化,氧学化沉1积8方h能法在制制备备出的孔A径A为O模15板0-的20孔0中成功制备了Ni纳米线阵列,分别用扫描电镜(SEM)、高分辨透射电镜(HRTEM)、X射线衍射(XRD)和X射线能量散射光谱(EDS)对其进行了表征;结果显示,制备的Ni纳米线排列整齐有序,每根Ni纳米线直径几乎相同,约150nm,长度约为180-200μm,长径比为1200-1300,与AAO模板的参数一致.研究了Ni纳米线阵列的长径比对其磁性能的影响,发现大长径比的Ni纳米线阵列具有明显的磁各向异性,而长径比约为200的Ni纳米线阵列未表现出明显的磁各向异性.本文结果表明,恒电流二次氧化方法能制备大长径比的AAO模板,并能用于制备大长径比的一维纳米材料阵列,可望在制备具有特殊光学、磁学等性能材料方面得到应用.     

铅纳米线阵列的制备

使用电化学沉积方法,在有序的氧化铝模板(AAO)孔洞中制备了铅纳米线有序阵列。用X射线衍射仪(XRD)、场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)对样品的结构、形貌、进行表征和观测。XRD的结果表明所制备的样品为纯的立方面心铅,且纳米线生长沿<220>有很好的取向。FE-SEM的图片清晰地说明铅纳米线阵列是大面积、高填充率和高度有序的。TEM的结果显示纳米线直径均匀、表面光滑且长径比大。     

硫化镉纳米线的电沉积制备及表征

以不同孔径的多孔阳极氧化铝为模板,采用直流电沉积的方法,在含CdCl2和S的DMSO溶液中制备出了CdS纳米线．SEM、TEM表征的结果表明,在不同孔径的多孔阳极氧化铝模板中,通过沉积时间等条件的控制,制得直径不同、长度可达5μm的平行结构、均匀而连续的CdS纳米线阵列．电子衍射和能谱结果显示所得的纳米线属于六方晶系CdS,线中Cd和S原子比接近1：1．     

单晶Ni纳米线阵列的制备与磁性能

采用恒电流沉积方法, 在多孔阳极氧化铝(AAO)模板中制备出了具有单晶结构的Ni纳米线阵列. 采用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射(XRD)技术对制备的Ni纳米线阵列的形貌及结构进行了表征. 利用振动样品磁强计(VSM)对单晶Ni纳米线阵列的磁性能进行了研究. 结果表明, 单晶镍纳米线阵列的易磁化方向为纳米线轴向, 并且与多晶纳米线相比显示出了更高的矫顽力. 直径为30 nm的纳米线具有较高的矫顽力(8.236×104 A/m)和较高的剩磁比(Mr＝0.94Ms).     

ZnO纳米线阵列的电沉积法制备及表征(英文)

利用直流电沉积方法在多孔氧化铝模板的孔洞中生成锌纳米线,在氧气氛围中,于800°C下氧化2h,将氧化铝中的锌氧化成氧化锌.本研究利用氧气氛围进行锌的氧化,大大提高了传统方法的氧化锌纳米线的制备效率.用场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)和X射线衍射仪(XRD)对其形貌及成分进行表征和分析,结果表明,氧化铝模板的有序孔洞中填充了大尺寸、均匀连续的多晶态氧化锌纳米线.纳米线具有约1000:1的高纵横比,其长度等于氧化铝模板的厚度,直径约为80nm.光致发光(PL)光谱表明,氧化锌纳米线在504nm处有由于氧空位引起的较强蓝绿光发射.这为进一步研究ZnO/AAO组装体发学性质和开发新型功能器件提供了基础.     

金、铜金属纳米棒或纳米线的AFM和SERS的研究(英文)

通过电化学氧化法制备具有不同孔径氧化铝模板 ,利用交流电镀的方法在模板中沉积金属 ,再用酸溶解模板可以得到相应尺度的金属纳米线或纳米棒的阵列 .本文利用原子力显微镜和表面增强拉曼技术分别表征了金和铜两种金属纳米线阵列 .研究结果表明 ,作为探针分子的硫氰(SCN )在金属纳米线上的碳氮三键的振动频率随纳米线直径的增大而蓝移 .这一现象可能是因为尺寸效应对纳米线的费米能级造成影响 ,使不同直径的金属纳米线电子结构存在微小的差别 .     

有序CdS纳米线阵列的制备和光学特性

应用直流电沉积法在多孔氧化铝模板中制备了高度有序的CdS纳米线阵列,并由XRD、Raman、SEM、TEM和HRTEM等进行物理化学表征.结果表明,沉积在多孔氧化铝模板中的CdS呈六角结构,c轴沿孔长度方向定向生长.紫外吸收光谱研究表明,随着纳米线尺寸的减小,纳米线阵列的吸收边向短波长方向移动,荧光光谱测量显示,CdS纳米线阵列的荧光强度高于氧化铝模板,而且在可见光区的荧光特性与激发波长无关.     

Nickel Amperometric Detector Prepared by Electroless Deposition for Microchip Electrophoretic Measurement of Alcohols and Sugars

Nickel was deposited directly at the end of an electrophoretic glass microchip using an electroless deposition procedure leading to an attractive amperometric detector for sugars and alcohols. Such direct electroless deposition of nickel at the end of the separation chip greatly simplifies the preparation of on‐chip electrochemical detectors. Variables affecting the preparation and operation of the new detector are characterized and optimized. The integrated capillary electrophoresis‐electrochemical detection microsystem was evaluated for the separation of alcohols and sugars in connection to assays of different beer and wine samples. Linear calibration plots and favorable detection limits are found that meet the needs of real sample (wine and beer) analyses. This represents the first example of using nickel electrode and detecting alcohols on microchip platforms.     

低Ni含量和低比表面积六铝酸盐LaNiAl11O19-δ催化剂上CH4-CO2重整反应的积炭

 利用 X 射线粉末衍射、氢程序升温还原、X 射线光电子能谱和透射电镜技术研究了在低 Ni 含量和低比表面积六铝酸盐催化剂 LaNiAl11O19-δ 上 CH4-CO2 重整反应的积炭行为, 考察了该催化剂表面积炭的形貌、来源、积炭物种及其反应性能. 结果表明, LaNiAl11O19-δ 催化剂表面积炭主要由甲烷裂解产生, 并以 Ni 的碳化物形式存在于活性中心 Ni 的周围. 根据积炭物种活化程度的难易可分为 Cα, Cβ和 Cγ 三种类型, 其中 Cα 为容易被 CO2 消除的化合碳, 而 Cβ 和 Cγ则是不易被 CO2 消除的石墨碳. 透射电镜结果表明, Cα 以碳纳米管形式分布于催化剂颗粒周围, 但金属 Ni 活性中心仍能暴露于气相中, 因而不影响催化剂的活性.     

Electrochemical performance of NaCo2O4 as electrode for supercapacitors

Sub-micron-scaled sodium cobalt oxide （NaCo2O4） powders are prepared by a solid-state reaction method. Characterization using X-ray diffraction indicates that the synthesized NaCo2O4 has a hexagonal layered structure. The electrochemical performance of the NaCo2O4 electrodes is investigated using cyclic voltarnmetry and galvanostatic charge/discharge in NaOH solution. The results show that the specific capacitance of the NaCo2O4 electrode reaches 337 F/g over the potential range of 0.15-0.65 V at a mass normalized current of 50 mA/g. Moreover, NaCo2O4 exhibits very good stability and cycling performance as a supercapacitor material.     

Applications of Non-precious Transition Metal Oxide Nanoparticles in Electrochemistry

Non-precious transition metal oxide nanomaterials offer numerous opportunities for various cost-effective electrochemical applications. This review article features the design and advancement of such nanomaterials with unique features applied for the fabrication of electrochemical devices. Also, it discusses various new syntheses of transition metal oxide nanoparticles (TMO NPs) via multiple chemicophysical and biological procedures. Further, the novel appliances of the TMO NPs with varying sizes and morphologies are appraised. The advantages and challenges of a number of investigations on the TMO NPs towards electrochemical applications are addressed with their standpoint of cost-effectiveness, applicability, and the efficiency of the introduced nanostructures for the industrial applications.     

NOx储存-还原催化剂Pt-Pd/BaO/TiAlO的制备及其抗硫性能

采用共沉淀-浸渍法制备了新型催化剂Pt-Pd/BaO/TiAlO,通过对催化剂进行NOx吸附储存实验、有硫(SO2)和无硫情况下的NOx储存-还原循环实验以及程序升温脱附、程序升温还原、N2吸附-脱附和X射线衍射等表征分析,考察了该催化剂的储存NOx性能以及抗硫性能.结果表明,在Pt-Pd/BaO/TiAlO中,复合氧化物TiAlO为储存NOx的组分兼载体,Ti和Al原子比为1∶2时,储存NOx能力最大;BaO(4%)作为助剂不但增加了催化剂的热稳定性,还提高了其储存NOx的能力.与Pt/BaO/γ-Al2O3相比,Pt-Pd/BaO/TiAlO具有良好的抗硫性能.Pt-Pd/BaO/TiAlO上吸附形成的硫化物稳定性较差,易被还原脱除,这是其抗硫性能良好的原因之一.     

Ni与Al2O3相互作用对Ni/Al2O3催化甲烷部分氧化制合成气抗积炭性能的影响

Ni/Al2O3是甲烷部分氧化制合成气反应常用的催化剂. 与Rh,Ru,Pt和Ir等贵金属负载型催化剂相比,其活性及选择性与Rh催化剂相近,且成本低,强度高,易于制备,是最具潜在应用前景的催化剂. 但是,在高温反应条件下,其活性组分Ni易烧结和流失,且催化剂表面易积炭而失活[1～3]. 此外,Ni与载体Al2O3在高温下相互作用生成难还原的NiAl2O4尖晶石,导致活性组分减少,造成催化剂活性下降. 人们通常都只注意到NiAl2O4的惰性,为了避免NiAl2O4晶相的生成,在消弱Ni与Al2O3之间的相互作用,提高催化剂的活性和稳定性等方面做了大量研究[4～7],但有关Ni与Al2O3之间的相互作用对稳定金属Ni的作用方面的报道却较少. Al-Ubaid等[8]发现Ni负载在NiAl2O4上显示出比其它载体更好的稳定性. Pena等[9]发现,NiAl2O4在乙炔加氢反应中有抑制积炭的作用. 范文浩等[10]在甲烷-二氧化碳重整制合成气催化剂的研究中,发现NiAl2O4的形成使催化剂的抗积炭性能大为改善,增强Ni-Al2O3相互作用,能有效地抑制碳丝生长. 本文在固定床流动反应装置上考察了Ni/Al2O3在甲烷部分氧化制合成气过程中的催化性能,并用XRD,XPS和TPR等手段考察了Ni负载量、焙烧温度和还原条件等对催化剂中Ni与Al2O3之间的相互作用及其对抗积炭性能的影响.     

Design of Functional Carbon Composite Materials for Energy Conversion and Storage

The carbon composite materials have been a research hotspot in the fields of catalysis, energy conversion and so on, because of their features of large structure and morphology variety, good chemical and electrochemical stability, and high electronic conductivity, large specific surface area and rich active sites. This paper summarizes some research progress of carbon composite materials, including assembly methodologies, their structure regulation, properties, and related applications. Moreover, the current challenges and the prospects of these materials are also discussed.     

Common Pitfalls of Reporting Electrocatalysts for Water Splitting

Rigorous assessment of heterogeneous electrocatalysts for electrochemical water splitting has been a critical issue mainly due to insufficient standard protocols to measure and report experimental data. In this perspective, we highlight some common pitfalls when measuring and reporting electrocatalytic data, which should be avoided to ensure the accuracy and reproducibility and to advance the water splitting field. We advocate to prevent the introduction of artefacts from the counter and reference electrodes, as well as the impurities in the electrolyte when conducting electrocatalyst activity measurements. In addition, we encourage the use of the electrochemically active surface area(ECSA)-normalized current densities to represent the intrinsic activity of the reported catalysts for a better comparison with previously known materials. Suitable ECSA measurement methods should be employed based on the nature of catalysts. Recommendations made in this perspective will hopefully assist in identifying advanced catalysts for water splitting research.     

三维有序大孔钙钛矿 LaFeO3 催化剂的制备及其催化炭黑颗粒燃烧性能

 采用水油两相双引发剂的无皂乳液聚合法制备了羧基改性的聚甲基丙烯酸甲酯 (PMMA) 聚合物微球, 并以此为模板, 采用胶体晶体模板法制备了三维有序大孔 (3DOM) 钙钛矿 LaFeO3 催化剂. 同时采用柠檬酸络合燃烧法制备了纳米钙钛矿 LaFeO3 催化剂. 通过傅里叶红外光谱、扫描电镜、X 射线衍射和激光粒度仪等方法对样品进行了表征. 采用程序升温氧化反应评价了催化剂对模拟柴油机炭黑颗粒催化燃烧的活性. 结果表明, 制备的羧基改性 PMMA 聚合物微球固含量约为 10%, 表面羧基含量约为 3 mmol/g. 微球粒径分布均匀, 且可通过调节反应条件得到不同的粒径, 可控范围在 300~700 nm. 所制得的 3DOM 钙钛矿 LaFeO3 催化剂以六方有序的方式排列, 其孔径及孔径收缩率分别为 300 nm 和 32%, 大孔孔壁平均厚度约 50 nm. 该催化剂对炭黑颗粒催化燃烧的 T10, T50, T90 和 SmCO2 分别为 340, 412, 458 oC 和 99.8%, 性能优于纳米 LaFeO3 催化剂.     

由杉木锯屑生物质制合成气:镍基整体式催化剂的表征及催化性能

以酸处理的蜂窝状堇青石为载体制得了一系列用于生物质热解气制合成气的不同NiO负载量的整体式催化剂,考察了该Ni基催化剂的催化性能.结果表明,酸处理后堇青石载体的比表面积和孔容分别可达156m2/g和0.099m3/g;NiO的负载使得比表面积和孔容急剧减小,并随着NiO负载量的增加而变化不大.NiO负载量对产气组分的影...     

Synthesis and thermal properties of poly(styrene-co-acrylonitrile)-graft-polyethylene glycol copolymers as novel solid–solid phase change materials for thermal energy storage

A novel poly(styrene-co-acrylonitrile)-graft-polyethylene glycol(SAN-g-PEG) copolymer was synthesized as new solid–solid phase change materials(SSPCMs) by grafting PEG to the main chain of poly(styrene-co-acrylonitrile). The chemical structure of the SAN-g-PEG was confirmed by the Fourier transform infrared(FT-IR) and proton nuclear magnetic resonance(1H NMR) spectroscopy techniques. The thermal energy storage properties and the storage durability of the SAN-g-PEG were investigated by differential scanning calorimetry(DSC). The SAN-g-PEG was endowed with the solid–solid phase transition temperatures within the range of 23–36 8C and the latent heat enthalpy ranged from 66.8 k J/kg to 68.3 k J/kg. Thermal cycling tests revealed that the SAN-g-PEG kept great heat storage durability after 1000 thermal cycles. The thermal stability was evaluated by a thermal gravity analysis(TGA), and the initial decomposition temperature(Td) of SAN-g-PEG is 350 8C, which proves that the SAN-g-PEG possessed good thermal stability.