环氧树脂/氧化石墨纳米复合物的等温固化行为研究

用示差扫描分析仪(DSC)研究了氧化石墨(GO)对N,N,N',N'-四缩水甘油基-4,4'-二氨基二苯基甲烷环氧树脂(TGDDM)/4,4'-二氨基二苯基砜(DDS)体系的等温固化反应的影响,用X射线光电子能谱仪(XPS)和傅里叶变换红外光谱仪(FTIR)研究了GO上存在的官能团及其对TGDDM/DDS体系固化行为的影响,用热失重分析仪(TGA)研究了天然石墨和GO的热力学稳定性.XPS、FTIR和TGA结果表明,GO上存在的大量羟基、羧基、环氧基等官能团能够影响环氧树脂的固化行为.DSC研究发现,环氧树脂/氧化石墨纳米复合物的固化反应属于自催化类型,随着GO含量的增加,达到最大反应速率的时间不断减小,初始反应速率不断增大,这说明GO对环氧树脂的固化反应有促进作用.Kamal模型计算得到的结果表明,随着GO含量的增加自催化反应初期阶段表观活化能E1先减小再增大,而自催化反应结束后表观活化能E2略微减小.经Kamal模型扩散控制函数修正后,整个固化过程中拟合得到的结果与实验数据相当吻合.以上结果说明,少量的GO对TGDDM/DDS体系的固化反应起着催化作用.     

酸酐固化环氧树脂/蒙脱土复合材料的等温固化动力学

用等温差示扫描量热法(DSC)研究了酸酐固化环氧树脂/蒙脱土复合材料的等温固化过程，考察了未处理的蒙脱土(MMT)和有机蒙脱土(OMMT)对环氧树脂固化动力学的影响. 实验表明， 环氧树脂的固化过程包含自催化机理，加入蒙脱土没有改变固化反应机理. 用Kamal方程对该体系的固化过程进行拟合，得到反应级数m、n，反应速率常数k1、k2，总反应级数(m + n)在2.4～3.0之间. MMT的加入使环氧树脂体系的k1、k2有所降低，而OMMT的加入对体系的k1、k2影响较为复杂，加入蒙脱土对环氧树脂固化体系的活化能影响较小.     

Isothermal cure kinetics of epoxy/phenol‐novolac resin blend system initiated by cationic latent thermal catalyst

The investigation of the cure kinetics of a diglycidyl ether of bisphenol A (DGEBA)/phenol‐novolac blend system with different phenolic contents initiated by a cationic latent thermal catalyst [N‐benzylpyrazinium hexafluoroantimonate (BPH)] was performed by means of the analysis of isothermal experiments using a differential scanning calorimetry (DSC). Latent properties were investigated by measuring the conversion as a function of curing temperature using a dynamic DSC method. The results indicated that the BPH in this system for cure is a significant thermal latent initiator and has good latent thermal properties. The cure reaction of the blend system using BPH as a curing agent was strongly dependent on the cure temperature and proceeded through an autocatalytic kinetic mechanism that was accelerated by the hydroxyl group produced through the reaction between DGEBA and BPH. At a specific conversion region, once vitrification took place, the cure reaction of the epoxy/phenol‐novolac/BPH blend system was controlled by a diffusion‐control cure reaction rather than by an autocatalytic reaction. The kinetic constants k₁ and k₂ and the cure activation energies E₁ and E₂ obtained by the Arrhenius temperature dependence equation of the epoxy/phenol‐novolac/BPH blend system were mainly discussed as increasing the content of the phenol‐novolac resin to the epoxy neat resin. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2945–2956, 2000     

几种聚醚胺改性蒙脱土对环氧树脂固化过程的影响

首先制备了五种聚醚胺改性蒙脱土(MMT), 并将这五种聚醚胺改性蒙脱土加入到双酚A 型环氧树脂E51 和聚醚胺D400体系中, 采用差示扫描量热法(DSC)考察了五种聚醚胺改性MMT对环氧树脂升温固化进程的影响. 随后, 优选一种EP/MMT 混合体系即EP/D400-T500-MMT 混合体系, 系统地研究了该体系与纯环氧树脂体系在130, 140, 150 及160 ℃等几个温度下的等温固化过程, 考察了等温固化时间对固化度和固化度变化速率的影响以及固化度与固化度变化速率之间的关系, 并利用Kamal 模型进行拟合计算了固化动力学参数. 研究结果表明, 与纯环氧树脂相比, 几种聚醚胺改性MMT 的固化放热峰均向高温迁移, 同时聚醚胺D400 协同插层MMT 降低了高分子量聚醚胺插层MMT 所导致的环氧树脂DSC 曲线的畸变情况; EP/D400-T500-MMT 混合体系和纯环氧体系的等温固化反应过程符合Kamal 模型;在相同的固化温度下, EP/D400-T5000-MMT 混合体系的反应速率常数k₁ 和k₂ 值以及反应级数m 均比纯EP 体系小, 而反应级数n 以及总反应级数m+n 值比纯EP 体系大, 表明两种聚醚胺协同插层的改性蒙脱土D400-T5000-MMT 的加入降低了环氧体系固化反应速率. 另外, EP/D400-T5000-MMT 混合体系的活化能E_a1 和E_a2 与纯EP 体系的相比也略有升高.     

Cure kinetics of carbon nanotube/tetrafunctional epoxy nanocomposites by isothermal differential scanning calorimetry

The cure kinetics of tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM) and 4,4′‐diaminodiphenylsulfone (DDS) as a cure agent in nanocomposites with multiwalled carbon nanotubes (MWNTs) have been studied with an isothermal differential scanning calorimetry (DSC) technique. The experimental data for both the neat TGDDM/DDS system and for epoxy/MWNTs nanocomposites showed an autocatalytic behavior. Kinetic analysis was performed with the phenomenological model of Kamal and a diffusion control function was introduced to describe the cure reaction in the later stage. Activation energies and kinetic parameters were determined by fitting experimental data. For MWNTs/epoxy nanocomposites, the initial reaction rates increased and the time to the maximum rate decreased with increasing MWNTs contents because of the acceleration effect of MWNTs. The values of the activation energies for the epoxy/MWNTs nanocomposites were lower than the values for the neat epoxy in the initial stage of the reaction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3701–3712, 2004     

Cure behavior of epoxy resin/montmorillonite/imidazole nanocomposite by dynamic torsional vibration method

Flory’s gelation theory, the non-equilibrium thermodynamic fluctuation theory and the Avrami equation have been used to predict the cure behavior of epoxy resin/organo-montmorillonite (Org-MMT)/imidazole intercalated nanocomposites at various temperatures and Org-MMT loadings. The theoretical prediction is in good agreement with the experimental results obtained by a dynamic torsional vibration method. The results show that the addition of Org-MMT reduces the gelation time t_g and increases the rate of the curing reaction, the value of the kinetic constant k. The half-time t_1/2 of cure after the gel point decreases with increasing of cure temperature, and the value of n is around 3 at lower temperature (<90 °C) and decreases to ∼2 as the temperature increases. The addition of Org-MMT has no obvious effect on the apparent activation energy of the cure reaction. There is no special curing process required for the formation of an epoxy resin/Org-MMT/imidazole intercalated nanocomposite.     

Curing Kinetics Modeling of Epoxy Modified by Fully Vulcanized Elastomer Nanoparticles Using Rheometry Method

In this study, the curing kinetics of epoxy nanocomposites containing ultra-fine full-vulcanized acrylonitrile butadiene rubber nanoparticles (UFNBRP) at different concentrations of 0, 0.5, 1 and 1.5 wt.% was investigated. In addition, the effect of curing temperatures was studied based on the rheological method under isothermal conditions. The epoxy resin/UFNBRP nanocomposites were characterized via Fourier transform infrared spectroscopy (FTIR). FTIR analysis exhibited the successful preparation of epoxy resin/UFNBRP, due to the existence of the UFNBRP characteristic peaks in the final product spectrum. The morphological structure of the epoxy resin/UFNBRP nanocomposites was investigated by both field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) studies. The FESEM and TEM studies showed UFNBRP had a spherical structure and was well dispersed in epoxy resin. The chemorheological analysis showed that due to the interactions between UFNBRP and epoxy resin, by increasing UFNBRP concentration at a constant temperature (65, 70 and 75 °C), the curing rate decreases at the gel point. Furthermore, both the curing kinetics modeling and chemorheological analysis demonstrated that the incorporation of 0.5% UFNBRP in epoxy resin matrix reduces the activation energy. The curing kinetic of epoxy resin/UFNBRP nanocomposite was best fitted with the Sestak–Berggren autocatalytic model.     

Exploitation of introducing of catalytic centers into layer galleries of layered silicates and related epoxy nanocomposites. I. Epoxy nanocomposites derived from montmorillonite modified with catalytic surfactant‐bearing carboxyl groups

Montmorillonite (MMT) was modified with the acidified cocamidopropyl betaine (CAB) and the resulting organo‐montmorillonite (O‐MMT) was dispersed in an epoxy/methyl tetrahydrophthalic anhydride system to form epoxy nanocomposites. The intercalation and exfoliation behavior of the epoxy nanocomposites were examined by X‐ray diffraction and transmission electron microscopy. The curing behavior and thermal property were investigated by in situ Fourier transform infrared spectroscopy and DSC, respectively. The results showed that MMT could be highly intercalated by acidified CAB, and O‐MMT could be easily dispersed in epoxy resin to form intercalated/exfoliated epoxy nanocomposites. When the O‐MMT loading was lower than 8 phr (relative to 100 phr resin), exfoliated nanocomposites were achieved. The glass‐transition temperatures (T_g's) of the exfoliated nanocomposite were 20 °C higher than that of the neat resin. At higher O‐MMT loading, partial exfoliation was achieved, and those samples possessed moderately higher T_g's as compared with the neat resin. O‐MMT showed an obviously catalytic nature toward the curing of epoxy resin. The curing rate of the epoxy compound increased with O‐MMT loading. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1192–1198, 2004     

Curing reaction of biphenyl epoxy resin with different phenolic functional hardeners

The investigation of cure kinetics and relationships between glass transition temperature and conversion of biphenyl epoxy resin (4,4′-diglycidyloxy-3,3′,5,5′-tetramethyl biphenyl) with different phenolic hardeners was performed by differential scanning calorimeter using an isothermal approach over the temperature range 120–150°C. All kinetic parameters of the curing reaction including the reaction order, activation energy, and rate constant were calculated and reported. The results indicate that the curing reaction of formulations using xylok and dicyclopentadiene type phenolic resins (DCPDP) as hardeners proceeds through a first-order kinetic mechanism, whereas the curing reaction of formulations using phenol novolac as a hardener goes through an autocatalytic kinetic mechanism. The differences of curing reaction with the change of hardener in biphenyl epoxy resin systems were explained with the relationships between T_g and reaction conversion using the DiBenedetto equation. A detailed cure mechanism in biphenyl-type epoxy resin with the different hardeners has been suggested. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 773–783, 1998     

On the effect of montmorillonite in the curing reaction of epoxy nanocomposites

The procedure for the fabrication of epoxy-based polymer layered silicate nanocomposites is important in respect of the nanostructure that is developed. To further our understanding of this, the influence of an organically modified clay (montmorillonite, MMT) on the curing kinetics of an epoxy resin has been studied by differential scanning calorimetry. Clay loadings of 10 and 20 mass% are used, and isothermal as well as dynamic cures have been investigated. For both cure schedules the effect of the MMT is to advance the reaction. Kinetic analysis yields values for the activation energy, but shows that the reaction cannot be described simply by the usual autocatalytic equation. The glass transition of the cured nanocomposites is lower than that for the cured neat resin, a result that is attributed to homopolymerisation taking place in addition to the epoxy–amine reaction.     

Cure behavior of epoxy resin/MMT/DETA nanocomposite

The Flory's gelation theory, non-equilibrium thermodynamic fluctuation theory and Avrami equation have been used to predict the gel time t _g and the cure behavior of epoxy resin/organo-montmorillonite/diethylenetriamine intercalated nanocomposites at various temperatures and organo-montmorillonite loadings. The theoretical prediction is in good agreement with the experimental results obtained by dynamic torsional vibration method, and the results show that the addition of organo-montmorillonite reduces the gelation time t _gand increases the rate of curing reaction, the value of k, and half-time of cure after gelation point t_1/2 decreases with the increasing of cure temperature, and the value of n is ~2 at the lower temperatures (<60°C) and decreases to ~1.5 as the temperature increases, and the addition of organo-montmorillonite decreases the apparent activation energy of the cure reaction before gelation point, but has no apparent effect on the apparent activation energy of the cure reaction after gelation point. There is no special curing process required for the formation of epoxy resin/organo-montmorillonite/diethylenetriamine intercalated nanocomposite. This revised version was published online in July 2006 with corrections to the Cover Date.     

Kinetics studies on the accelerated curing of liquid crystalline epoxy resin/multiwalled carbon nanotube nanocomposites

A new class of nanocomposite has been fabricated from liquid crystalline (LC) epoxy resin of 4,4′‐bis(2,3‐epoxypropoxy) biphenyl (BP), 4,4′‐diamino‐diphenyl sulfone (DDS), and multiwalled carbon nanotubes (CNTs). The surface of the CNTs was functionalized by LC epoxy resin (ef‐CNT). The ef‐CNT can be blended well with the BP that is further cured with an equivalent of DDS to form nanocomposite. We have studied the curing kinetics of this nanocomposite using isothermal and nonisothermal differential scanning calorimetry (DSC). The dependence of the conversion on time can fit into the autocatalytic model before the vitrification, and then it becomes diffusion control process. The reaction rate increases and the activation energy decreases with increasing concentration of the ef‐CNT. At 10 wt % of ef‐CNT, the activation energy of nanocomposite curing is lowered by about 20% when compared with the neat BP/DDS resin. If the ef‐CNT was replaced by thermal‐insulating TiO₂ nanorods on the same weight basis, the decrease of activation energy was not observed. The result indicates the accelerating effect on the nanocomposite was raised from the high‐thermal conductivity of CNT and aligned LC epoxy resin. However, at ef‐CNT concentration higher than 2 wt %, the accelerating effect of ef‐CNTs also antedates the vitrification and turns the reaction to diffusion control driven. As the molecular motions are limited, the degree of cure is lowered. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Mechanism Studies on Water Sorption and Permeation in Epoxy Resin by Impedance Spectroscopy. II. Cure Kinetics of O-Cresol Novolac Resin with Esterfied Phenol Novolac Resin

Abstract

To study the effect of water affinity of the cured epoxy resin on water sorption and permeation in the cured epoxy resin, a novel hardener (esterfied phenol novolac was synthesized and used for obtaining the cured product without free hydroxyl group. Differential Scanning Calorimetry (DSC) and Fourier Transform Infrared Spectroscopy (FT-IR) were used to study the cure kinetics of o-cresol novolac epoxy resin using esterfied phenol novolac resin as curing agent in the presence of 2-methylimidazole as accelerator. Some kinetic parameters of the curing reaction such as the reaction order, activation energy, and frequency factor were obtained in the temperature range studied. The results show that this curing process is a first-order kinetic mechanism, which was different with that cured with phenol novolac resin.     

基于松香酸酐的环氧树脂体系固化动力学及TTT图绘制

研制了基于松香酸酐固化剂的生物质环氧树脂体系,采用全动态DSC法研究了树脂体系的固化反应动力学,通过半经验的唯象模型拟合得到了固化反应参数,活化能Ea为59.68 kJ/g,指前因子A0为1.28×1015s-1,反应级数n为2.483,由此建立了体系固化温度/时间/固化度间的关系;采用恒温DSC及DMA方法测试玻璃化转变温度,应用DiBenedetto经验方程拟合得到了玻璃化转变温度与固化度间的关系.应用锥板旋转黏度计测试了树脂体系不同温度下的凝胶时间,通过线性回归分析得到了凝胶时间与温度之间的关系.由唯象模型和DiBenedetto方程分别计算得到凝胶时的固化度为0.386,玻璃化转变温度为26.22°C.由上述工作绘制了基于松香酸酐生物质树脂体系的TTT(time-temperature-transition diagram)固化图,可确定树脂体系在不同温度任意时间下的状态.     

Effect of thermoplastic toughening agent on glass transition temperature and cure kinetics of an epoxy prepreg

The isothermal time–temperature-transformation (TTT) cure diagram is developed in this article to investigate the effect of thermoplastic toughening agent on glass transition temperature (T _g) and cure kinetics of an epoxy carbon fiber prepreg, Cycom 977-2 unidirectional (UD) tape. The glass transition temperature was measured using differential scanning calorimetry (DSC) over a wide range of isothermal cure temperatures from 140 to 200 °C. Times to gelation and vitrification were measured using shear rheometry. The glass transition temperature master curve was obtained from the experimental data and the corresponding shift factors were used to calculate the activation energy. The kinetic rate model was utilized to construct iso-T _g contours using the calculated activation energy. It was observed that the iso-T _g contours did not follow the behavior of the neat epoxy resin, since they deviated from the gel time curve. This deviation was believed to be the effect of the thermoplastic toughening agent. The behavior of the neat epoxy resin in 977-2 was shown by constructing the iso-T _g contours using the activation energy obtained from gel time modeling.     

Cure Kinetics of Poly(acrylonitrile-butadiene-styrene) Modified Epoxy–Amine System

The cure kinetics of epoxy based on the diglycidyl ether of bisphenol A (DGEBA) modified with different amounts of poly(acrylonitrile-butadiene-styrene) (ABS) and cured with 4,4′-diaminodiphenylsulfone (DDS) was investigated by employing differential scanning calorimetry (DSC). The curing reaction was followed by using an isothermal approach over the temperature range 150–180°C. The amount of ABS in the blends was 3.6, 6.9, 10 and 12.9 wt%. Blending of ABS in the epoxy monomer did not change the reaction mechanism of the epoxy network formation, but the reaction rate seems to be decreased with the addition of the thermoplastic. A phenomenological kinetic model was used for kinetic analysis. Activation energies and kinetic parameters were determined by fitting the kinetic model with experimental data. Diffusion control was incorporated to describe the cure in the latter stages, predicting the cure kinetics over the whole range of conversion. The reaction rates for the epoxy blends were found to be lower than that of the neat epoxy. The reaction rates decreased when the ABS contents was increased, due to the dilution effect caused by the ABS on the epoxy/amine reaction mixture.     

双酚-S环氧树脂与琥珀酸酐固化反应动力学

用差示扫描量热法（ＤＳＣ）研究了双酚－Ｓ环氧树脂（ＢＰＳＥＲ）与琥珀酸酐固化反应的历程。实验结果表明,固化反应主要分两个阶段,前期由化学动力学控制,服从自催化机理。实验数据利用Ｋａｍａｌ方程处理得到两个速率常数ｋ、、ｋ２及两个反应级数ｍ、ｎ、ｋ１、ｋ２的值随反应温度的升高呈增大的趋势,总反应级数ｍ＋ｎ在２～２．５之间,当转化率达到４０％左右后,由于交联程度增加,分子量迅速增长,分子间扩散较慢,进入     

Lanthanide–imidazole complexes as latent curing agents for epoxy resins

Imidazoles have for some time been recognized as curing agents for epoxy resins. Once the resin and the imidazole compound are mixed there is a relatively short time in which the mixture can be used, since the polymerization (curing) reaction occurs to some extent even at room temperature causing the reaction mixture to thicken. In order to circumvent this problem we have found that imidazoles can be complexed with organo-lanthanide compounds thereby tying up the imidazole and retarding its rate of reaction in the cure of epoxy materials at ambient temperatures. When it is desired to enhance the rate of cure the temperature of the mixture is simply raised. This paper concerns studies of the epoxy cure reaction with the M(THD)₃–IM series. M represents the lanthanide metals Eu, Ho, Pr, Dy, Yb, and Gd, and THD is 2,2,6,6-tetramethyl-3,5-heptanedione. Cure reactions were followed by differential scanning calorimetry and in some cases by infrared spectroscopy. We have demonstrated that these organo-lanthanide–imidazole complexes are effective thermally latent curing agents for epoxy resins. At a temperature of 150°C cure is quite rapid. In the course of these studies it has also been determined that there is an inverse correlation between the lanthanide ionic radius in the complex and the temperature at which the cure reaction occurs. Thus the Yb compound, where the imidazole is most strongly bound, cures at the highest temperature and Pr, where imidazole is bound most weakly, at the lowest. Consistent with these facts is the observation that the Yb compound also gives the longest latency period when mixed with epoxy resin.     

Development of toughened bio‐based epoxy with epoxidized linseed oil as reactive diluent and cured with bio‐renewable crosslinker

In the current work, renewable resourced toughened epoxy blend has been developed using epoxidized linseed oil (ELO) and bio‐based crosslinker. Epoxidation of linseed oil was confirmed through FTIR and ¹H NMR spectra. The ELO bio‐resin was blended at different compositions (10, 20, and 30 phr) with a petroleum‐based epoxy (DGEBA) as reactive diluent to reduce the viscosity for better processibility and cured with cardanol‐derived phenalkamine to overcome the brittleness. The flow behavior of the neat epoxy and modified bio‐epoxy resin blend systems was analyzed by Cross model at low and high shear rates. The tensile and impact behavior studies revealed that the toughened bio‐epoxy blend with 20 to 30 phr of ELO showed moderate stiffness with much higher elongation at break 7% to 13%. Incorporation of higher amount of ELO (20 to 30 phr) increases enthalpy of curing without affecting peak temperature of curing. The thermal degradation behavior of the ELO based blends exhibits similar trend as neat epoxy. The higher intensity or broadened loss tangent curve of bio‐epoxy blends revealed higher damping ability. FE‐SEM analysis showed a rough and rippled surface of bio‐based epoxy blends ensuring effective toughening. Reduced viscosity of resin due to maximum possible incorporation of bio‐resin and use of phenalkamine as curing agent leads to an eco‐friendly toughened epoxy and can be useful for specific coating and structural application.     

Insights into phthalonitrile/epoxy blends modification system from non-competitive cure system based on alicyclic anhydride

A series of polymer blends were prepared from 1,3-bis(3,4-dicyanophenoxy)benzene (3BOCN) and epoxy resin with methyl tetrahydrophthalic anhydride as curing agent.The curing behavior and curing kinetics of the blends were studied by differential scanning calorimetry.The apparent activation energy of the blends with various contents of 3BOCN was higher than that of the blends without 3BOCN.A model experiment suggested that there is no obvious reaction between phthalonitrile and epoxy.The thermal and mechanical properties of the polymer blends were evaluated.The polymer blends exhibit high storage modulus and char yield compared with the neat epoxy.The polymer blends show ductile fracture morphology by scanning electron microscopy (SEM) images.