Thermal transitions and dynamics in nanocomposite hydrogels

Hydrogels based on nanocomposites of statistical poly(hydroxyethyl acrylate-co-ethyl acrylate) and silica, prepared by simultaneous copolymerization and generation of silica nanoparticles by sol?Cgel process at various copolymer compositions and silica contents, characterized by a fine dispersion of filler, were investigated with respect to glass transition and polymer dynamics by dielectric techniques. These include thermally stimulated depolarization currents and dielectric relaxation spectroscopy, covering together broad ranges of frequency and temperature. In addition, equilibrium water sorption isotherms were recorded at room temperature (25?°C). Special attention was paid to the investigation of effects of silica on glass transition, polymer dynamics (secondary ?? and ?? _sw relaxations and segmental ?? relaxation), and electrical conductivity in the dry systems (xerogels) and in the hydrogels at various levels of relative humidity/water content. An overall reduction of molecular mobility is observed in the nanocomposite xerogels, in particular at high silica contents. Analysis of the results and comparison with previous work on similar systems enable to discuss this reduction of molecular mobility in terms of constraints to polymeric motion imposed by interfacial polymer?Cfiller interactions and by the formation of a continuous silica network interpenetrated with the polymer network at filler contents higher than about 15?wt%.     

Nanoparticle Dispersion and Glass Transition Behavior of Polyimide-grafted Silica Nanocomposites

How to control the spatial distribution of nanoparticles to meet different performance requirements is a constant challenge in the field of polymer nanocomposites.Current studies have been focused on the flexible polymer chain systems.In this study,the rigid polyimide(PI) chain grafted silica particles with different grafting chain lengths and grafting densities were prepared by "grafting to" method,and the influence of polymerization degree of grafted chains(N),matrix chains(P),and grafting density(a) on the spatial distribution of nanoparticles in the PI matrix was explored.The glass transition temperature(Tg) of PI composites was systematically investigated as well.The results show that silica particles are well dispersed in polyamic acid composite systems,while aggregation and small clusters appear in PI nanocomposites after thermal imidization.Besides,the particle size has no impact on the spatial distribution of nanoparticles.When σ·N0.5<<(N/P)2,the grafted and matrix chains interpenetrate,and the frictional resistance of the segment increases,resulting in restricted relaxation kinetics and Tg increase of the PI composite system.In addition,smaller particle size and longer grafted chains are beneficial to improving Tg of composites These results are all propitious to complete the microstructure control theory of nanocomposites and make a theoretical foundation for the high performance and multi-function of PI nanocomposites.     

Synthesis,thermal properties and crystalline morphology of poly(trimethylene terephthalate)/ZnO nanocomposites prepared by dual in situ polymerization

Poly(trimethylene terephthalate)/ZnO nanocomposites were successfully prepared by dual in situ polymerization. Firstly, ZnO nanoparticles were synthesized by a simple polyol method using 1,3‐propanediol (PDO) as solvent and stabilizer. Then, PTT/ZnO nanocomposites were prepared by in situ polymerization. The results of Fourier transform infrared spectra showed that PTT molecular chains were grafted to the surface of ZnO nanoparticles. The results of ¹H NMR spectra confirmed that propyl ester molecules (as reaction product) were incorporated into PTT molecular chains. It was found that the intrinsic viscosity and molecular weight of synthesized PTT decreased with the addition of ZnO nanoparticles and the incorporation of propyl ester molecules. TEM results showed that ZnO nanoparticles with particle size of 20 ~ 30 nm were well dispersed and fully distributed in the polymer matrix. Besides, the melting temperatures and crystallization temperature decreased gradually and then increased slightly with the increasing loading of ZnO nanoparticles. Because of the strong interaction between ZnO nanoparticles and PTT matrix, the thermal stability of PTT/ZnO nanocomposites was improved. Interestingly, the results of Polarized Optical Microscopy showed that banded spherulites morphology can be observed in all PTT/ZnO nanocomposite samples. However, at higher loading of ZnO nanoparticles, band spacing became larger and was finally disturbed. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis and characterization of poly(methylmethacrylate)/silica nanocomposites: Study of the interphase by solid‐state NMR and structure/properties relationships

Organic/inorganic nanocomposites were synthesized from poly(methylmethacrylate) (PMMA) and properly modified silica nanoparticles by in situ polymerization. Methacryloylpropyltrimethoxysilane was selected as nanoparticle surface modifier because it is characterized by unsaturated end groups available to radical reactions, making possible to suppose their participation in the acrylic monomer polymerization. As a result of the above hypothesized reactions, a phase constituted by polyacrylic chains grafted onto modified silica surface was isolated. ²⁹Si and ¹³C solid‐state nuclear magnetic resonance experiments permitted to analyze this phase in terms of composition and chain mobility as well as to highlight interaction mechanisms occurring between growing PMMA oligoradicals and functional groups onto silica surface. It was demonstrated that this PMMA grafted onto silica surface acts as an effective coupling agent and assures a good dispersion of nanoparticles as well as a strong nanoparticle/matrix interfacial adhesion. As a result of strong interactions occurring between phases, a significant increase of the glass transition temperature was recorded. Finally, the abrasion resistance of PMMA in the hybrids was significantly improved as a result of a different abrasion propagation mechanism induced by silica particles thus overcoming one of the most serious PMMA drawback. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Confined crystallization behaviors in polyethylene/silica nanocomposites: Synergetic effects of interfacial interactions and filler network

The confinement effects introduced by nanoparticles have been reported to influence the phase behaviors thus the properties of polymer nanocomposites. In this study, molecular dynamics and crystallization behaviors of polyethylene (PE) composited with three types of silica (SiO₂) nanoparticles, namely unmodified SiO₂, hydrophobically modified SiO₂, SiO₂‐APTES (3‐aminopropyltriethoxysilane) and SiO₂‐PTES (n‐propyltriethoxysilane), were systematically investigated via a combination of DSC, XRD and ¹H solid‐state NMR measurements. The suppressions in crystallization and chain mobilities of PE rank in the order of unmodified SiO₂ < SiO₂‐APTES < SiO₂‐PTES due to the increasing interfacial interactions between PE and SiO₂ nanoparticles. Additionally, independent of polymer–nanoparticle interactions, a silica network forms for all three kinds of nanocomposites when SiO₂ content reaches 83 wt %. The mobilities of polymer chains are severely restricted by such a percolated network structure, leading to a turning point in the crystallization ability of nanocomposites and a new crystallization peak at 45 °C lower than that of pure PE. The synergetic effects of interfacial interactions and filler network on polymer crystallization have been thoroughly studied in this work, which will provide guidance on modifying and designing nanocomposites with controlled properties. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 498–505     

Role of adsorbed chain rigidity in reinforcement of polymer nanocomposites

The thermomechanical behavior of polymer nanocomposites is mostly governed by interfacial properties which rely on particle–polymer interactions, particle loading, and dispersion state. We recently showed that poly(methyl methacrylate) (PMMA) adsorbed nanoparticles in poly(ethylene oxide) (PEO) matrices displayed an unusual thermal stiffening response. The molecular origin of this unique stiffening behavior resulted from the enhanced PEO mobility within glassy PMMA chains adsorbed on nanoparticles. In addition, dynamic asymmetry and chemical heterogeneities existing in the interfacial layers around particles were shown to improve the reinforcement of composites as a result of good interchain mixing. Here, the role of chain rigidity in this interfacially controlled reinforcement in PEO composites is investigated. We show that particles adsorbed with less rigid polymers improve the mechanical properties of composites. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 9–14     

Molecular Dynamics and Structure of Poly(Methyl Methacrylate) Chains Grafted from Barium Titanate Nanoparticles

Core−shell nanocomposites comprising barium titanate, BaTiO₃ (BTO), and poly(methyl methacrylate) (PMMA) chains grafted from its surface with varied grafting densities were prepared. BTO nanocrystals are high-k inorganic materials, and the obtained nanocomposites exhibit enhanced dielectric permittivity, as compared to neat PMMA, and a relatively low level of loss tangent in a wide range of frequencies. The impact of the molecular dynamics, structure, and interactions of the BTO surface on the polymer chains was investigated. The nanocomposites were characterized by broadband dielectric and vibrational spectroscopies (IR and Raman), transmission electron microscopy, differential scanning calorimetry, and nuclear magnetic resonance. The presence of ceramic nanoparticles in core–shell composites slowed down the segmental dynamic of PMMA chains, increased glass transition temperature, and concurrently increased the thermal stability of the organic part. It was also evidenced that, in addition to segmental dynamics, local β relaxation was affected. The grafting density influenced the self-organization and interactions within the PMMA phase, affecting the organization on a smaller size scale of polymeric chains. This was explained by the interaction of the exposed surface of nanoparticles with polymer chains.     

Frequency‐Driven Self‐Organized Helical Superstructures Loaded with Mesogen‐Grafted Silica Nanoparticles

Adding colloidal nanoparticles into liquid‐crystal media has become a promising pathway either to enhance or to introduce novel properties for improved device performance. Here we designed and synthesized new colloidal hybrid silica nanoparticles passivated with a mesogenic monolayer on the surface to facilitate their organo‐solubility and compatibility in a liquid‐crystal host. The resulting nanoparticles were identified by ¹H NMR spectroscopy, TEM, TGA, and UV/Vis techniques, and the hybrid nanoparticles were doped into a dual‐frequency cholesteric liquid‐crystal host to appraise both their compatibility with the host and the effect of the doping concentration on their electro‐optical properties. Interestingly, the silica‐nanoparticle‐doped liquid‐crystalline nanocomposites were found to be able to dynamically self‐organize into a helical configuration and exhibit multi‐stability, that is, homeotropic (transparent), focal conic (opaque), and planar states (partially transparent), depending on the frequency applied at sustained low voltage. Significantly, a higher contrast ratio between the transparent state and scattering state was accomplished in the nanoparticle‐embedded liquid‐crystal systems.     

Effect of silica nanofillers on isothermal crystallization of poly(vinyl alcohol): In-situ ATR-FTIR study

Isothermal crystallization behavior of poly(vinyl alcohol) (PVA) in the presence and absence of silica nanoparticles was systematically investigated using in-situ attenuated total reflectance Fourier-transform infrared (ATR-FTIR) spectroscopy. The content, size, and surface characteristics of silica nanoparticles were considered as main factors affecting the crystallization behavior, and the effect of annealing time and temperature was also examined. First, very low concentrations of silica nanoparticles (less than 0.5 wt%) could accelerate the crystallization process, whereas higher silica loadings reduced the degree of crystallization. In the PVA/silica (0.5 wt%) nanocomposites, 22-nm silica nanoparticles provided the most suitable interparticle space for nucleation and crystal growth. Compared with hydrophobic silica nanoparticles, hydrophilic silica nanoparticles are favorable to achieve higher crystallinity due to the increased chemical affinity in the nanocomposites. The degree of crystallization became higher with increasing annealing time and it was also enhanced in a high-temperature region. When 0.5 wt% of 22-nm silica nanoparticles was used as a nucleating agent for the crystallization of PVA, the crystallinity of nanocomposites was ca. 20% higher than that of pristine PVA.     

Obtaining of Ni<Subscript>0.65</Subscript>Zn<Subscript>0.35</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> nanocomposites by thermal decomposition of complex compounds embedded in silica matrix

This article presents the results of our investigation on the obtaining of Ni_0.65Zn_0.35Fe₂O₄ ferrite nanoparticles embedded in a SiO₂ matrix using a modified sol–gel synthesis method, starting from tetraethylorthosilicate (TEOS), metal (Fe^III,Ni^II,Zn^II) nitrates and ethylene glycol (EG). This method consists in the formation of carboxylate type complexes, inside the silica matrix, used as forerunners for the ferrite/silica nanocomposites. We prepared gels with different compositions, in order to obtain, through a suitable thermal treatment, the nanocomposites (Ni_0.65Zn_0.35Fe₂O₄)_x–(SiO₂)_100–x (where x=10, 20, 30, 40, 50, 60 mass%). The synthesized gels were studied by differential thermal analysis (DTA), thermogravimetry (TG) and FTIR spectroscopy. The formation of Ni–Zn ferrite in the silica matrix and the behavior in an external magnetic field were studied by X-ray diffraction (XRD) and quasi-static magnetic measurements (50 Hz).     

Synthesis of Macroporous PMMA/Silica Nanocomposite Monoliths in Supercritical Carbon Dioxide

Summary: Macroporous monoliths consisting of silica nanoparticles embedded in poly(methyl methacrylate) (PMMA) were synthesized in supercritical CO₂. Well‐dispersed silica particles, pretreated with functional 3‐(trimethoxysilyl)propyl methacrylate (MPS), were to form colloidal PMMA nanocomposites followed by a sol‐gel transition forming interconnected structures resulting in micron‐sized pores with specific areas between 1 and 7 m² · g⁻¹. SEM and TEM results revealed uniform morphological characteristics of the composite materials and good dispersions of the silica nanoparticles.

SEM micrograph of PMMA/Silica nanocomposites forming interconnected macroporous monolith. The average size of the silica particles is 50 nm.     

Effect of fulleroid materials on the mechanical and tribological properties and dielectric relaxation of polyamide 6 nanocomposites

The effect of fulleroid materials (fullerene С₆₀ and fullerene soot, which is used for fullerenes production) on the mechanical and tribological properties of polymer nanocomposites based on polyamide 6 (PA6) was investigated. Composites were synthesized by direct mixing in an extruder. The use of the nanoparticles was an effective way to decrease the friction coefficient of the polymer composites because the fillers had the same size as the segments of the surrounding polymer chains. The steady state coefficients of friction with addition of fulleroid fillers were lower than that of unfilled PA6. The lowest coefficient of friction was observed for PA6 filled with 1 wt% fullerene soot. Dielectric spectroscopy was used to investigate the influence of nanoparticles on the relaxation processes in the polymer matrix. It is found that the segmental relaxation processes become faster with the addition of fullerene С₆₀. In contrast, the secondary processes of PA6/fullerene C₆₀ nanocomposites were observed to slow down with the addition of fullerene C₆₀. This means that the local “molecular stiffness” is increased, and a phenomenological link between the secondary relaxation times and the mechanical properties explains the increase in the Young's modules of the nanocomposites upon the addition of С₆₀. These observations suggest that nanoparticles can have a qualitatively different effect on the matrix polymer dynamics at different length scales, and caution must be taken in comparing the changes in the dynamics associated with different relaxation processes. Copyright © 2016 John Wiley & Sons, Ltd.     

Physical aging and glass transition of hairy nanoparticle assemblies

Matrix free assemblies of polymer-grafted, “hairy” nanoparticles (aHNP) exhibit novel morphology, dielectric, and mechanical properties, as well as providing means to overcome dispersion challenges ubiquitous to conventional polymer-inorganic nanocomposite blends. Physical aging of the amorphous polymer glass between the close-packed nanoparticles (NPs) will dominate long-term stability; however, the energetics of volume recovery within the aHNPs is unknown. Herein, we compare glass transition temperature (T_g) and enthalpy recovery of aHNPs to NP-polymer blends, across different nano-silica loadings (0–50 v/v%) and canopy architecture of polystyrene (PS) grafted silica. For aHNPs, the grafting of PS to silica imposes an additional design constraint between silica volume fraction, graft density, and graft molecular weight. At low and intermediate silica volume fraction, the T_g of blended nanocomposites is independent of silica content, reflecting a neutral polymer-NP interface. For aHNPs, the T_g decreases with silica content, implying that chain tethering decreases local segment density more than the effect of molecular weight or polymer-NP interactions. Additionally, the T_g of the aHNPs is higher than a linear matrix of comparable molecular weight, implying a complementary effect to local segment density that constrains cooperativity. In contrast, enthalpy recovery rate in the blend or aHNP glass is retarded comparably. In addition, a cross-over temperature, T_x, emerges deep within the glass where the enthalpy recovery process of all nanocomposites becomes similar to linear unfilled matrices. Differences between structural recovery in aHNP and blended nanocomposites occur only at the highest silica loadings (∼ 50 v/v%), where enthalpy recovery for aHNPs is substantially suppressed relative to the blended counterparts. The absence of physical aging at these loadings is independent of brush architecture (graft density or molecular weight of tethered chains) and indicates that the impact of chain tethering on effective bulk structural relaxation starts to appear at particle-particle surface separations on the order of the Kuhn length. Overall, these observations can be understood within the context of how three separate structural characteristics impact local segment density and relaxation processes: the dimension and architecture of the tethered polymer chains, the separation between NP surfaces, and the confinement imposed by chain tethering and space filling within the aHNP. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 319–330     

Thermal decomposition of metal nitrates

The paper presents a study regarding the preparation of 40 %M^IIFe₂O₄/60 %SiO₂ nanocomposites (M = Ni, Zn, Cu) by thermal decomposition of metal nitrates—poly(vinyl alcohol)–tetraethyl orthosilicate gels. Thermal analysis and FT-IR spectroscopy have evidenced that a redox reaction takes place between PVA and NO ₃ ^? ions in the pores of the formed hybrid gels. The result of this redox reaction is the formation of carboxylate-type coordination compounds that have the role of a precursor of the ferrite nanoparticles. By thermal decomposition of these precursors inside the silica matrix, the corresponding MFe₂O₄/SiO₂ nanocomposites are obtained starting with 600 °C, as resulting from XRD analysis. Elemental maps of the corresponding involved elements M (Ni, Zn, Cu), Fe, and Si have confirmed the homogenous distribution of the ferrite nanoparticles within the silica matrix. TEM images have shown that the nanocomposites were obtained as fine nanoparticles, with diameter up to 20 nm. All nanocomposites 40 %M^IIFe₂O₄/60 %SiO₂ obtained at 1000 °C presented magnetic properties characteristic to this type of nanocomposite.     

Nuclear magnetic resonance as a powerful tool for evaluation of intermolecular interaction: Correlation with rheological measurements of recycled nanocomposite

The degradation of polystyrene nanocomposite was carried out by mechanical recycling after multiple processing of thermo-oxidative ageing. It was found that the degradation of the quaternary salt present in the clay promotes degradation of the polymer. The clay exfoliation was affected by the nanocomposite degradation process as well as the dipolar interactions of polymer chains, which influences the physical and mechanical properties of the final nanocomposite. NMR is a powerful tool for the characterization at the molecular level; it is sensitive to variations in local segmental and global movements. The correlation between NMR relaxation and rheological analyses in polymer nanocomposites was observed. This study aims to understand the complex effects of degradation in polymeric systems containing nanoparticles. Several ¹H NMR relaxation parameters were analyzed. From the base line of the domain curves, the dipolar interaction phenomenon in polystyrene chains was investigated. The polymer chain heterogeneity was determined quantitatively from the MSE-FID, using a combination of Abragamian, Gaussian and exponential functions to fit experimental data. At least three domains: rigid, intermediate and mobile phases were identified based on the molecular mobilities.     

Reinforcement effect of carbon nanofillers in an epoxy resin system: Rheology,molecular dynamics,and mechanical studies

The reinforcing effect of carbon nanoparticles in an epoxy resin has been estimated with different approaches based on rheology, molecular dynamics (evaluated by differential scanning calorimetry, dielectric relaxation spectroscopy, and thermally stimulated depolarization current), and dynamic mechanical analysis. Carbon particles aggregate as the volume increases and form a fractal structure in the matrix polymer. The dispersion microstructure has been characterized by its viscoelastic properties and relaxation time spectrum. The scaling of the storage modulus and yield stress with the volume fraction of carbon shows two distinct exponents and has thus been used to determine the critical carbon volume fraction of the network formation (Φ*) for the carbon/epoxy dispersions. At nanofiller concentrations greater than Φ*, the overall mobility of the polymer chains is restricted in both dispersions and solid nanocomposites. Therefore, (1) the relaxation spectrum of the dispersions is strongly shifted toward longer times, (2) the glass‐transition temperature is increased and (3) the relaxation strength of both the secondary (β) and primary (α) relaxations increases in the nanocomposites, with respect to the pure polymer matrix. The dispersion microstructure, consisting of fractal flocs and formed above Φ*, is proposed to play the main role in the reinforcement of nanocomposites. Moreover, the network structure and the interface polymer layer (bond layer), surrounding nanoparticles, increases the relaxation strength and slows the cooperative α relaxation, and this results in an improvement of the mechanical properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 522–533, 2005     

Studies of molecular dynamics of carboxylated acrylonitrile-butadiene rubber composites containing in situ synthesized silica particles

The molecular dynamics of carboxylated acrylonitrile-butadiene rubber - silica hybrid materials was investigated. Silica hybrids were formed in situ rubber matrix using varied amounts of N-(2-aminoethyl)-3-aminopropyltrimethoxysilane (DAMS), serving also as a cross-linker. Filler-filler and filler-rubber interactions were present, due to the specific nature of these materials. It was found that the amounts of added aminosilane determined the cross-linking density of obtained materials and was the highest with 20 phr DAMS used. The cross-links had ionic nature. Dielectric relaxation spectroscopy (DRS) revealed β, α and α′ relaxation processes. The β relaxation, correlated with the mobility of polymer side groups, was influenced by the weak interaction between both acrylonitrile and carboxylic groups of the rubber and silanol groups of silica. The activation energy for that relaxation was similar for all materials (∼32 kJ mol⁻¹). Both DRS and dynamical mechanical analysis (DMA) demonstrated that the amount of in situ formed silica filler did not significantly influence either the temperature of the α relaxation (correlated with glass transition) or its activation energy. Therefore, that relaxation was caused by free polymer chains, not attached to the silica particles. Similar values of glass transition temperature (T_g) for all hybrids were confirmed by DSC. It appeared that the amplitude of tangent delta (DMA) within T_g was dependent on silica amount. Detected at higher temperature α′ relaxation resulted from the presence of domains, where polymer chains were affected by silica network, geometrical restrictions and morphology of the silica-rich domains.     

纳米复合材料中界面动态特性的扫描静电显微技术研究

纳米复合材料中的微观界面结构和界面作用对材料的宏观介电性能, 如介电常数、介电损耗、击穿强度等有十分重要的影响. 本文发展了一种基于扫描静电显微探针技术的测量方法, 可以直接表征二氧化钛/环氧树脂纳米复合材料的微观界面结构及相应的动态介电响应行为. 实验中利用扫描探针的纳米尺度分辨能力, 探测到不同温度下环氧树脂纳米复合材料的局域动态介电响应变化过程, 从而获得纳米颗粒与高分子界面相互作用及极化相关的温度特性. 进一步通过对二氧化钛纳米颗粒进行表面修饰, 得到了两种不同特性的二氧化钛/环氧树脂界面, 验证了不同界面作用引起的复合材料界面区域与非界面区域高分子链介电损耗图像的反差.     

Investigation on Structures and Properties of Shape Memory Polyurethane/Silica Nanocomposites

In this study, high performance shape memory polyurethane (SMPU)/silica nanocomposites with different silica weight fraction including SMPU bulk, 3%, 4.5%, 6%, 7.5%, 10%, were prepared by sol‐gel process initiated by the solid acid catalyst of p‐toluenesulfonic acid (PTSA). Field emission scanning electron microscopy (FE‐SEM) and transmission electron microscopy (TEM) observation show that the silica nanoparticles are dispersed evenly in SMPU/silica nanocomposites. Tensile test and dynamic mechanical analysis (DMA) suggest that the mechanical properties and the glass transition temperature (T_g) of the nanocomposites were significantly influenced by silica weight fraction. Thermogravimetric analysis (TGA) was utilized to evaluate the thermal stability and determine the actual silica weight fraction. The TGA results indicate that the thermal stability can be enhanced with the hybridization of silica nanoparticles. Differential scanning calorimetry (DSC) was conducted to test the melting enthalpy (ΔH) and the results suggest that the ΔH was markedly improved for the SMPU/silica nanocomposites. Thermomechanical test was conducted to investigate the shape memory behavior and the results show that the shape fixity is improved by hybridization of silica and good shape recovery can be obtained with the increasing of cycle number for all the samples.     

Preparation and characterization of film-forming raspberry-like polymer/silica nanocomposites via soap-free emulsion polymerization and the sol–gel process

Herein, we report on the synthesis of film-forming poly(styrene-co-butyl acrylate-co-acrylic acid)/SiO₂ [P(St-BA-AA)/SiO₂] nanocomposites by in situ formation of SiO₂ nanoparticles from TEOS via sol–gel process in the presence of poly(acrylic acid) (PAA)-functionalized poly(styrene-co-butyl acrylate) [P(St-BA)] particles fabricated by soap-free emulsion polymerization. The formed silica particles could be absorbed by polyacrylate chains on the surface of PAA-functionalized P(St-BA) particles; thus, raspberry-like polymer/silica nanocomposites would be obtained. Transmission electron microscopy, Fourier transform infrared spectroscopy, attenuated total reflectance infrared spectrum, ultraviolet–visible transmittance spectra, and thermogravimetric analysis were used to characterize the resulting composites. The results showed that the hybrid polymer/silica had a raspberry-like structure with silica nanoparticles anchored on the surface of polymer microspheres. The thermal, fire retardant, and mechanical properties and water resistance of the film were improved by incorporating silica nanoparticles, while the optical transmittance was seldom affected due to nanosized silica particles uniformly dispersed in the film.