共缩聚型可溶性聚酰亚胺的微波辐射合成

以均苯四甲酸酐(PMDA)、3,3′,4,4′-二苯酮四羧酸二酐(BTDA)和甲苯2,4-二异氰酸酯(TDI)为单体,微波辐射低温溶液聚合生成一种共缩聚聚酰亚胺(PI).通过特性黏度([η])、红外光谱(FT-IR)、热失重分析(TGA)和X衍射分析(XRD)等对聚合物进行了一系列的结构表征和性能测试.结果表明,微波辐射溶液聚合能够提高PI的特性黏数及产率,微波的引入大大缩短了反应时间;FT-IR表明,在1779cm-1和1726cm-1处观察到聚酰亚胺特征峰;TGA表明,PI在氮气中520℃左右开始降解,10%热失重温度为585℃;溶解性测试表明,PI可以溶解在强极性非质子溶剂中,如DMF,DMSO,DMAc及NMP等,甚至部分溶解在THF中.     

Comparative study on polyimides from isomeric 3,3′‐, 3,4′‐, and 4,4′‐linked bis(thioether anhydride)s

Three isomeric bis(thioether anhydride) monomers, 4,4′‐bis(2,3‐dicarboxyphenylthio) diphenyl ketone dianhydride (3,3′‐PTPKDA), 4,4′‐bis(3,4‐dicarboxyphenylthio) diphenyl ketone dianhydride (4,4′‐PTPKDA), and 4‐(2,3‐dicarboxyphenylthio)‐4′‐(3,4‐dicarboxyphenylthio) diphenyl ketone dianhydride (3,4′‐PTPKDA), were prepared through multistep reactions. Their structures were determined via Fourier transform infrared, NMR, and elemental analysis. Three series of polyimides (PIs) were prepared from the obtained isomeric dianhydrides and aromatic diamines in N‐methyl‐2‐pyrrolidone (NMP) via the conventional two‐step method. The PIs showed excellent solubility in common organic solvents such as chloroform, N,N‐dimethylacetamide, and NMP. Their glass‐transition temperatures decreased according to the order of PIs on the basis of 3,3′‐PTPKDA, 3,4′‐PTPKDA, and 4,4′‐PTPKDA. The 5% weight loss temperatures (T_5%) of all PIs in nitrogen were observed at 504–519 °C. The rheological properties of isomeric PI resins based on 3,3′‐PTPKDA/4,4′‐oxydianiline/phthalic anhydride showed lower complex viscosity and better melt stability compared with the corresponding isomers from 4,4′‐ and 3,4′‐PTPKDA. In addition, the PI films based on three isomeric dianhydrides and 2,2′‐bis(trifluoromethyl)benzidine had a low moisture absorption of 0.27–0.35%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of highly refractive polyimides from 4,4′‐thiobis[(p‐phenylenesulfanyl)aniline] and various aromatic tetracarboxylic dianhydrides

An aromatic sulfur‐containing diamine 4,4′‐thiobis[(p‐phenylenesulfanyl) aniline] (3SDA) was synthesized and polymerized with a sulfur‐containing dianhydride 4,4′‐[p‐thiobis(phenylenesulfanyl)]diphthalic anhydride (3SDEA) and three nonsulfur aromatic tetracarboxylic dianhydrides, respectively to afford four poly(amic acid)s (PAAs) with the inherent viscosities of 0.54–1.04 dL/g. Flexible and tough polyimide (PI) films obtained from the PAA precursors showed good thermal, mechanical, and optical properties. The glass transition temperatures (T_gs) of the PIs ranged from 179.1–227.2 °C determined by differential scanning calorimetry (DSC), and 173.8–227.3 °C by dynamic mechanical analysis (DMA), depending on the dianhydride used. The 10% weight loss temperatures were in the range of 500–536 °C, showing high intrinsic thermal‐resistant characteristics of the PI films. The PI films also showed good optical transparency above 500 nm, which agreed well with the calculated absorption spectra using the time‐dependent density functional theory. The average refractive indices (n_av) measured at 632.8 nm were 1.7191–1.7482, and the in‐plane/out‐of‐plane birefringences (Δn) were 0.0068–0.0123. The high refractive indices originate from the high sulfur contents, good molecular packing, and the absence of bulky structures. The relatively small birefringence mainly results from the flexible thioether linkages structures of the diamine. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5606–5617, 2007     

Alkaline-developable positive-type photosensitive polyimide with high mechanical strength and high resolution based on chain extendable poly(amic acid), thermally degradable cross-linker and photoacid generator

A positive-type photosensitive polyimide ( PSPI ) based on a chain extendable poly(amic acid) ( PAA ), a thermally degradable cross-linker 1,3,5-tris[(2-vinyloxy)ethoxy]benzene ( TVEB ), and a photoacid generator (PAG) (5-propylsulfonyloxyimino-5H-thiophene-2-ylidene)-(2-methylphenyl)acetonitrile ( PTMA ) has been developed. The chain extendable PAA was prepared from 3,3′,4,4′-biphenyltetracarboxylic dianhydride ( BPDA ) and 4,4′-oxydianiline ( ODA ) and end-capped with di-tert-butyl dicarbonate ( DIBOC ) in N-methyl-2-pyrrolidone (NMP), which has a controlled molecular weight for developing in a 2.38 wt% tetramethyl ammonium hydroxide aqueous solution ( TMAH _aq ) and undergoes a chain extending reaction during curing stage. The photosensitive resist solution was formulated with the polymerization solution (30 wt% in NMP), TVEB (15 wt% for the polymer), and PAG (4.5 wt% for the polymer). The PSPI showed a sensitivity of 47 mJ cm⁻² and a contrast of 5.8 when exposed to 365-nm light, followed by postexposure baking at 90 °C for 10 min and development with the 2.38 wt% TMAH _aq at room temperature. A fine-positive image with 3-μm line-and-space patterns was obtained on a 3-μm thick film exposed to UV light at 365 nm in the contact-printed mode. After thermal curing at 350 °C for 1 hr, the resulting PSPI features excellent mechanical strength and elongation.     

Synthesis and Characterization of Fluorinated Polyimide Derived from 3,3′‐Diisopropyl‐4,4′‐diaminodiphenyl‐3′′,4′′‐difluorophenylmethane

A novel aromatic diamine monomer, 3,3′‐diisopropyl‐4,4′‐diaminodiphenyl‐3′′,4′′‐difluorophenylmethane (PAFM), was successfully synthesized by coupling of 2‐isopropylaniline and 3,4‐difluorobenzaldehyde. The aromatic diamine was adopted to synthesize a series of fluorinated polyimides by polycondensation with various dianhydrides: pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (ODPA) and 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA) via the conventional one‐step method. These polyimides presented excellent solubility in common organic solvents, such as N,N‐dimethylformamide (DMF), N,N‐dimethyl acetamide (DMAc), dimethyl sulfoxide (DMSO), N‐methyl‐2‐pyrrolidone (NMP), chloroform (CHCl₃), tetrahydrofuran (THF) and so on. The glass transition temperatures (T_g) of fluorinated polyimides were in the range of 260–306°C and the temperature at 10% weight loss in the range of 474–502°C. Their films showed the cut‐off wavelengths of 330–361 nm and higher than 80% transparency in a wavelength range of 385–463 nm. Moreover, polymer films exhibited low dielectric properties in the range of 2.76–2.96 at 1 MHz, as well as prominent mechanical properties with tensile strengths of 66.7–97.4 MPa, a tensile modulus of 1.7–2.1 GPa and elongation at break of 7.2%–12.9%. The polymer films also showed outstanding hydrophobicity with the contact angle in the range of 91.2°–97.9°.     

Low‐CTE photosensitive polyimide based on semialicyclic poly(amic acid) and photobase generator

A negative‐type photosensitive polyimide (PSPI) based on semialicyclic poly(amic acid) (PAA), poly(trans‐1,4‐cyclohexylenediphenylene amic acid), and {[(4,5‐dimethoxy‐2‐nitrobenzyl)oxy]carbonyl} 2,6‐dimethylpiperidine (DNCDP) as a photobase generator has been developed as a next‐generation buffer coat material. The semialicyclic PAA was synthesized from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and trans‐1,4‐cyclohexyldiamine in the presence of acetic acid, and the PAA polymerization solution was directly used for PSPI formulation. This PSPI, consisting of PAA (80 wt %) and DNCDP (20 wt %), showed high sensitivity of 70 mJ/cm² and high contrast of 10.3, when it was exposed to a 365‐nm line (i‐line), postexposure baked at 190 °C for 5 min, and developed with 2.38 wt % tetramethylammonium hydroxide aqueous solution containing 20 wt % isopropanol at 25 °C. A clear negative image of 6‐μm line and space pattern was printed on a film, which was exposed to 500 mJ/cm² of i‐line by a contact printing mode and fully converted to poly(trans‐1,4‐cyclohexylenebiphenylene imide) pattern upon heating at 250 °C for 1 h. The PSPI film had a low coefficient of thermal expansion of 16 ppm/K compared to typical PIs, such as prepared from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 4,4′‐oxydianiline. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1317–1323, 2010     

Influence of temperature and imidization method on the structure and properties of polyimide fibers prepared by wet spinning

A polyamic acid (PAA) based on 4,4′-bis(4-aminophenoxy)diphenyldiamine and 1,3-bis-(3′,4-dicarboxyphenoxy)benzene dianhydride was synthesized. PAA fibers were prepared by wet spinning. Subsequent cyclization of PAA units was achieved using chemical or thermal imidization. The influence of the imidization method and process conditions on the chemical structure, porosity, morphology, thermal and mechanical properties of polyimide (PI) fibers was studied. Thermal imidization was carried out in the temperature range from 60 to 300 °C at different process durations. The degree of imidization of PI fibers was studied by IR spectroscopy. The structure and properties of PI fibers were studied by scanning electron microscopy, thermal analysis, and by measuring the stress-strain properties.

     

Molecular design,synthesis, and nonlinear optical properties of novel T‐type polyimides with exceptionally high thermal stability of the second harmonic generation

2,5‐Bis‐(3,4‐dicarboxyphenylcarboxyethoxy)‐4′‐nitrostilbene dianhydride was prepared and reacted with 1,4‐phenylenediamine, 4,4′‐oxydianiline, 4,4′‐diaminobenzanilide, and 4,4′‐(hexafluoroisopropylidene)dianiline to yield unprecedented novel T‐type polyimides ( 4 – 7 ) containing 2,5‐dioxynitrostilbenyl groups as nonlinear optical chromophores, which constituted parts of the polymer backbones. 4 – 7 were soluble in polar solvents such as acetone and N,N‐dimethylformamide. They showed thermal stability up to 300 °C in thermogravimetric analysis thermograms; the glass‐transition temperatures obtained from differential scanning calorimetry thermograms were around 153 °C. The second harmonic generation (SHG) coefficients (d₃₃) of poled polymer films at the 1064‐cm^?1 fundamental wavelength were around 4.35 × 10^?9 esu. The dipole alignment exhibited exceptionally high thermal stability even at 45 °C higher than the glass‐transition temperature, and there was no SHG decay below 200 °C because of the partial main‐chain character of the polymer structure, which was acceptable for nonlinear optical device applications. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3189–3199, 2004     

Synthesis and properties of novel Y‐type nonlinear optical polyimides with high thermal stability of second harmonic generation

2,4‐Bis‐(3,4‐dicarboxyphenylcarboxyethoxy)‐1‐(2,2‐dicyanovinyl)benzene dianhydride (4) was prepared and reacted with 4,4′‐oxydianiline, 4,4′‐diaminobenzanilide and 4,4′‐(hexafluoroisopropylidene)dianiline to yield novel Y‐type polyimides 5‐7 containing 2,4‐dioxybenzylidenemalononitrile groups as nonlinear optical (NLO) chromophores, which constitute parts of the polymer backbone. The resulting polyimides 5‐7 are soluble in polar solvents such as dimethylsulfoxide and N,N‐dimethylformamide. Polymers 5‐7 showed a thermal stability up to 330 °C in thermogravimetric analysis thermograms with T_g values obtained from differential scanning calorimetry thermograms in the range 179–194 °C. The second harmonic generation (SHG) coefficients (d₃₃) of poled polymer films at the 1064 nm fundamental wavelength were around 5.56 × 10^?9 esu. The dipole alignment exhibited exceptionally high thermal stability even at 20 °C higher than the glass‐transition temperature there was no SHG decay below 215 °C because of the partial main‐chain character of polymer structure, which is acceptable for NLO device applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3078–3087, 2008     

Alkaline-developable and negative-type photosensitive polyimide with high sensitivity and excellent mechanical properties using photo-base generator

An alkaline developable and negative-type PSPI with a high sensitivity and excellent mechanical properties based on a poly(amic acid) (PAA) and a photo-base generator has been developed. The PAA was prepared by the polycondensation of p-phenylenediamine (PDA) with an equimolar of 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) and 4,4′-(hexafluoroisopropylidene)diphthalic anhydride (6-FDA) and converted thermally to the corresponding polyimide, PI(PDA-BPDA/6-FDA). PI(PDA-BPDA/6-FDA) showed the high thermal and mechanical properties and the dimensional stability such as the thermal decomposition temperature of 530°C, glass transition temperature of 369°C, linear coefficient of thermal expansion of 28 ppm/K, ultimate tensile strength of 148 MPa, elongation at break of 25% and dielectric constant of 2.8. The PSPI was formulated directly from PAA(PDA-BPDA/6-FDA) with a photo-base generator (PBG), (E)-3-(2-hydroxy-4-methoxyphenyl)-1-(piperidin-1-yl)prop-2-en-1-one (HMPP) (10 wt% to PAA) and the optimized parameters for photolithographic process were investigated including the PBG content, post-exposure bake (PEB) temperature, and PEB time. The PSPI based on PAA(PDA-BPDA/6-FDA) and HMPP (10 wt% to PAA) showed a sensitivity of 114 mJ/cm² and contrast of 1.29 when exposed to 365-nm light (i-line), post-exposure baked at 160°C for 5 min, and developed with an aqueous solution of 2.38 wt% tetramethylammonium hydroxide and iso-propanol. A clear negative 8-μm features pattern was obtained by contact-printing and converted into the PI pattern upon heating at 250°C, confirming by scanning electron microscopy and infrared spectroscopy.     

Synthesis and Characterization of Organosoluble Poly(imide-ether)s with Bulky 2,3-Diaryl Imidazole Moiety: Study Physical,Thermal and Optical Properties

Two new symmetrical diamines were designed and synthesized having different functional groups such as a pair of phenyl ether linkages, 2,3-diaryl substituted imidazole rings and CF₃ groups as pendant, and characterized by FT-IR, ¹H and ¹³C-NMR spectroscopy and elemental analysis. A series of new fluorescent poly(imide-ether)s (PIEs) was prepared by polymerization of the diamines with commercial tetracarboxylic dianhydrides such as pyromellitic dianhydride and 3,3′,4,4′-benzophenone tetracarboxylic dianhydride. The resulting PIEs were amorphous and had intrinsic viscosity [η] in the range of 0.42–0.51 dL/g. The weight average molecular weights (Mw) of these polymers were measured by GPC and were in the range of 28658–35595 g/mol with molecular weight distribution (MWD) of 2.12–2.27. These polymers were readily soluble in a variety of organic solvents and formed low-colored and flexible thin films with cut-off wavelength (λ₀) in the range of 385–420 nm, and all PIEs films exhibited high optical transparency. They also possessed good thermal stability with 10% weight loss temperatures (T_10%) in the range 486–537°C in N₂. The glass transition temperatures (T_g) of PIEs are in the range 251–324°C. These polymers showed fluorescence emission in film and in solution at 459–476 nm with the quantum yields in the range 4–12%.     

Synthesis and properties of novel polyimides from sulfonated binaphthalene dianhydride for proton exchange membranes

A sulfonated dianhydride monomer, 6,6′‐disulfonic‐4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (SBTDA), was successfully synthesized by direct sulfonation of the parent dianhydride, 4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (BTDA), using fuming sulfuric acid as the sulfonating reagent. A series of sulfonated homopolyimides were prepared from SBTDA and various common nonsulfonated diamines. The resulting polymer electrolytes, which contain ion conductivity sites on the deactivated positions of the aryl backbone rings, displayed high proton conductivities of 0.25–0.31 S cm^?1 at 80 °C. The oxidative stability test indicated that the attachment of the ? SO₃H groups onto the dianhydride units did not deteriorate the oxidative stability of the SPI membranes. The better membranes were achieved by the copolymerization of nonsulfonated diamine, SBTDA, and BTDA. Copolymer membrane synthesized from hexane‐1,6‐diamine, SBTDA, and BTDA displayed excellent water stability of more than 1000 h at 90 °C, while its proton conductivity was still at a high level (comparable to that of Nafion 117). Furthermore, the novel block copolymer ( II‐b ) displayed higher proton conductivity compared with the random one ( II‐r ) obviously, probably due to the slightly higher water uptake and better microphase separated morphology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2820–2832, 2008     

Synthesis and properties of poly(amic acid)s and polyimides based on 2,2′,6,6′‐biphenyltetracarboxylic dianhydride

Poly(amic acid)s (PAAs) having the high solution stability and transmittance at 365 nm for photosensitive polyimides have been developed. PAAs with a twisted conformation in the main chains were prepared from 2,2′,6,6′‐biphenyltetracarboxylic dianhydride (2,2′,6,6′‐BPDA) and aromatic diamines. Imidization of PAAs was achieved by chemical treatment using trifluoroacetic anhydride. Among them, the PAA derived from 2,2′,6,6′‐BPDA and 4,4′‐(1,3‐phenylenedioxy)dianiline was converted to the polyimide by thermal treatment. The heating at 300 °C under nitrogen did not complete thermal imidization of PAAs having glass‐transition temperatures (T_g)s higher than 300 °C to the corresponding PIs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6385–6393, 2006     

Unique fluorescence behavior of perylenetetracarboxydiimides in polyimide systems

Perylenetetracarboxydiimide (PEDI) molecularly dispersed in polyamic acid (PAA) and polyimide (PI) films has unique fluorescence properties. An originally strong fluorescence of PEDI is efficiently quenched in the PAA films. The systematic variation of the chain structure of the PAA matrices revealed that the aromatic amide groups in the PAA chains function as a quencher. When a PAA derived from 3,4,3′4′-biphenyltetracarboxylic dianhydride (BPDA) and p-phenylenediamine (PDA), BPDA/PDA, was used as a matrix polymer, the fluorescence of the dye dispersed in the film increased abruptly as imidization of the matrix proceeds. But annealing at temperatures higher than 320°C in the step-heating process caused a gradual decrease in the fluorescence intensity. The decreased intensity results from the dye–PDA units interactions intensified by the denser molecular packing of the matrix polymer chains. PEDI shows significant dependence of the fluorescence intensity on the chain structure of the PI matrices. In the various PI films containing a fixed diamine component, the dye fluorescence intensity reduces linearly with an increase in the intramolecular charge transfer ability of the PI matrices. From the result, we propose a fluorescence quenching mechanism through multistep electron transfer processes. The BPDA/PDA polyimide matrix leads to a strong PEDI fluorescence whereas the pyromellitic dianhydride (PMDA)-based PI matrices do not. For the blends composed of these PIs, the fluorescence of PEDI bound into the main chains provides a valuable indicator of the miscibility on the molecular level. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 827–840, 1998     

Three‐component negative‐type photosensitive polyimide precursor based on poly(amic acid), a crosslinker,and a photoacid generator

A new negative‐working and alkaline‐developable photosensitive polyimide precursor based on poly(amic acid) (PAA), 4,4′‐methylenebis[2,6‐bis(hydroxymethyl)]phenol (MBHP) as a crosslinker, and a photoacid generator (5‐propylsulfonyloxyimino‐5H‐thiophen‐2‐ylidene)‐2‐(methylphenyl)acetonitrile (PTMA) has been developed. PAA was prepared by ring‐opening polymerization of pyromellitic dianhydride with 4,4′‐oxydianiline. The photosensitive polyimide precursor containing PAA (65 wt %), MBHP (25 wt %), and PTMA (10 wt %) showed a clear negative image featuring 10 μm line and space patterns when it was exposed to 436 nm light at 100 mJ·cm^?2, post‐exposure baked at 130 °C for 3 min, followed by developing with a 2.38 wt % aqueous tetramethylammonium hydroxide solution at 25 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 593–599, 2005     

Synthesis and properties of fluorinated polyimides from a new unsymmetrical diamine: 1,4‐(2′‐Trifluoromethyl‐4′,4′‐diaminodiphenoxy)benzene

A new aromatic, unsymmetrical ether diamine with a trifluoromethyl pendent group, 1,4‐(2′‐trifluoromethyl‐4′,4″‐diaminodiphenoxy)benzene, was successfully synthesized in three steps with hydroquinone as a starting material and polymerized with various aromatic tetracarboxylic acid dianhydrides, including 4,4′‐oxydiphthalic anhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, 2,2′‐bis(3,4‐dicarboxyphenyl)‐hexafluoropropane dianhydride, and pyromellitic dianhydride, via a conventional two‐step thermal or chemical imidization method to produce a series of fluorinated polyimides. The polyimides were characterized with solubility tests, viscosity measurements, IR, ¹H NMR, and ¹³C NMR spectroscopy, X‐ray diffraction studies, and thermogravimetric analysis. The polyimides had inherent viscosities of 0.56–0.77 dL/g and were easily dissolved in both polar, aprotic solvents and common, low‐boiling‐point solvents. The resulting strong and flexible polyimide films exhibited excellent thermal stability, with decomposition temperatures (at 5% weight loss) above 522 °C and glass‐transition temperatures in the range of 232–272 °C. Moreover, the polymer films showed outstanding mechanical properties, with tensile strengths of 74.5–121.7 MPa, elongations at break of 6–13%, and initial moduli of 1.46–1.95 GPa, and good dielectric properties, with low dielectric constants of 1.82–2.53 at 10 MHz. Wide‐angle X‐ray diffraction measurements revealed that these polyimides were predominantly amorphous. These outstanding combined features ensure that the polymers are desirable candidate materials for advanced microelectronic applications. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6836–6846, 2006     

Characterization of cobalt-modified polyimides

Modified polyimide films containing cobalt have been prepared by the addition of cobalt(II) chloride to a solution containing one of the diamines 4,4′-oxydianiline (ODA) or 4,4′-diaminodiphenylsulfide (DDS) and one of the dianhydrides 3.3′, 4,4′-benzophenonetetracarboxylic dianhydride (BTDA) or 4,4′-bis(3,4-dicarboxyphenoxy)diphenylsulfide dianhydride (BDSDA) and characterized by thermal methods, UV-visible spectra, room-temperature direct-current electrical resistivity measurements, and X-ray photoelectron and Auger electron spectroscopy. A principal goal of this work was to establish if there was coordination of the potential donor atoms of the polymide to cobalt. UV-visible spectra of the modified polyamic acid solutions and polyimide films and a titration study of a model system do not show any appreciable coordination with either the polyamic acid or the polyimide; rather, the cobalt(II) appears to be coordinated to the solvent, N,N-dimethylacetamide (DMAc), as [Co(DMAc)₄]²⁺, until the temperature is raised above 200°C. X-ray photoelectron spectra of films cured only to 200°C also do not show significant shifts in the binding energies of the potential donor atoms from those binding energies of the undoped polymers, confirming little direct coordination of the cobalt to atoms of the polyimide. Heating the films to 300°C in a forced-air oven causes the formation of a cobalt oxide layer on the air side of the polymer. Direct-current electrical resistivity measurements on this surface show a 10⁴–10⁶ reduction in resistivity due to this layer.     

Studies on polyimide imidization in far‐infrared radiation

In this paper, the monomers 4,4′‐oxydiphthalic anhydride (ODPA), 3,3′,4,4′‐biphenyl dianhydride (BPDA), 3,4′‐oxidianiline (3,4′‐ODA), and 4,4′‐oxidianiline (4,4′‐ODA) were selected to synthesize polyimides (PI) or copolyimides (co‐PI) in N,N‐dimethyl acetamide (DMAc) by two‐step method. To control the PI molecular weight (MW), phthalic anhydride (PA) was used as the end‐capping reagent. The effect of far‐infrared radiation (FIR) on PI imidization was investigated by Fourier transform infrared spectroscopy (FTIR). Some factors affecting imidization process in FIR were discussed, including PI imidization time and temperature, molecular structure, designed number average molecular weight, crystalline, imidization procedure, film thickness, polyamide acid (PAA) solid content, and so forth. The PI imidization process in FIR will be affected by all these factors. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3621–3627, 2005     

Direct patterning of poly(amic acid) and low‐temperature imidization using a crosslinker,a photoacid generator,and a thermobase generator

A positive‐type photosensitive polyimide (PSPI) based on poly(amic acid) (PAA), a crosslinker 1,1,1‐tris{4‐[2‐(vinyloxy)ethoxy]phenyl}ethane (TVPE), a photoacid generator (PAG) (5‐propylsulfonyloxyimino‐5H‐thiophen‐2‐ylidene)‐2‐(methylphenyl)acetonitrile (PTMA), and a thermobase generator (TBG) t‐butyl 2,6‐dimethylpiperidine‐1‐carboxylate (BDPC) has been developed as a promising material in microelectronics. The PAA was prepared from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐oxydianiline (ODA) in dimethyl sulfoxide (DMSO). The PSPI, consisting of PAA (69 wt %), TPVE (21 wt %), PTMA (3 wt %), and BDPC (7 wt %), showed high sensitivity of 21 mJ/cm² and a high contrast of 6.8 when it was exposed to a 436‐nm line (g‐line), postbaked at 90 °C for 5 min, and developed with 1.69 wt % TMAHaq. A clear positive image of 8 μm line and space pattern was printed on film, which was exposed to 50 mJ/cm² of g‐line by a contact printing mode and fully converted to the corresponding polyimide (PI) pattern on heating at 200 °C, confirmed by FTIR spectroscopy. Thus, this system will be a good candidate for next generation PSPIs. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3362–3369, 2009     

Design,synthesis, and gas permeation properties of polyimides containing pendent imidazolium groups

Film‐forming polymers containing ionic groups have attracted considerable attention as emerging materials for gas separation applications. The aim of this article was to synthesize new film‐forming polyimides containing imidazolium groups (PI‐IMs) and establish their structure–performance relationship. In this context, a new aromatic diamine, namely, N¹‐(4‐aminophenyl)‐N¹‐(4‐(2‐phenyl‐1H‐imidazol‐1‐yl)phenyl)benzene‐1,4‐diamine (ImTPADA), was synthesized and polycondensed with three aromatic dianhydrides, namely, 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride, 4,4‐(4,4‐isopropylidenediphenoxy) bis(phthalic anhydride), and 4,4′‐oxydiphthalic anhydride to form the corresponding polyimides containing pendent 2‐phenylimidazole groups (PI‐IEs). Next, PI‐IMs were prepared by N‐quaternization of pendent 2‐phenylimidazole groups present in PI‐6FDA using methyl iodide followed by anion exchange with bis(trifluoromethane)sulfonimide lithium salt (LiTf₂N). PI‐IEs and PI‐IMs exhibited reasonably high molecular weights, amorphous nature, good solubility, and could be cast into self‐standing films from their DMAc solutions. Thermogravimetric analysis showed that 10% weight loss temperature of PI‐IEs and PI‐IMs were in the range 545–475 °C and 303–306 °C, respectively. Gas permeability analysis of films of PI‐IEs and PI‐IMs was investigated by variable‐volume method and it was observed that incorporation of ionic groups into PI‐6FDA resulted in increased permeability while maintaining selectivity. In particular, polymer bearing Tf₂N⁻ anion exhibited high CO₂ permeability (33.3 Barr) and high selectivity for CO₂/CH₄ (41.1) and CO₂/N₂ (35.4). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1721–1729