Phonon Raman scattering in Nd1+xBa2−xCu3O7−δ and Pr1+xBa2−xCu3O7−δ single crystals

The polarized Raman spectra of Nd_1+xBa_2−xCu₃O_7−δ (−0.023≤x≤0.107) and Pr_1+xBa_2−xCu₃O_7−δ (0.01≤x≤0.15) single crystals have been investigated. It was found that the Cu(2) A_g mode softens by 6 cm⁻¹ in Nd 1:2:3 and 4 cm⁻¹ in Pr 1:2:3 as x increases. These frequency shifts cannot be explained by the change in the relevant bond lengths due to Nd(Pr)-substitution for Ba. The variations with x of the two low frequency modes may be affected by change of their hybridization and/or change of their force constants. The linewidths of Ba mode in Pr 1:2:3 are broader than those in Y 1:2:3. This result suggests that the Pr substitution on Ba sites occurred even in a very small value of x. In x(yy) geometry the relative intensity of the Ba and O(4) modes in Nd 1:2:3 is greater than those in Pr 1:2:3. The difference between Nd 1:2:3 and Pr 1:2:3 in the relative intensity of the Ba and O(4) modes may be produced by the chains.     

High temperature susceptibility of semimagnetic-semiconductor Zn1-xMnxS

This paper gives an analysis of the high temperature susceptibility of diluted semimagnetic-semiconductor Zn_{1 − x}Mn_xS. The high-temperature susceptibility of Zn_{1 − x}Mn_xS was found to behave in accordance with the Curie-Weiss law. From _χ(T) measurements the exchange integral of Mn²⁺ -Mn²⁺ interaction 2J₁/k_B = (-34.6±0.5) K (effective exchange integral) was obtained. A spin S = 2.6±0.1, close to its atomic value S = , was also found. The role of the superexchange in this alloy is shortly discussed at the end of the paper.     

Perpendicular magnetic anisotropy of Fe-Nd alloy thin films

A study of the magnetic properties of Fe_{100 − x}Nd_x (18 x 50) films made by rf sputtering has been carried out. The perpendicularly magentized films were fabricated for compositions in the range from x = 35 to 50 at substrate temperatures between 210 to 290°C. The intrinsic perpendicular magnetic anisotropy constant K_u is maximum at about x = 40 where K_u is about 1 × 10⁷ erg/cm³ at room temperature. The temperature dependence of K_u implies that the origin of the perpendicular magnetic anisotropy may be related to some sort of atomic ordering of crystalline clusters in an amorphous matrix.     

Material design of new lithium ionic conductor, thio-LISICON, in the Li2S–P2S5 system

A new lithium ionic conductor of the thio-LISICON (LIthium SuperIonic CONductor) family was found in the binary Li₂S–P₂S₅ system; the new solid solution with the composition range 0.0≤x≤0.27 in Li_3+5xP_1−xS₄ was synthesized at 700 °C and characterized by X-ray diffraction measurements. Its electrical and electrochemical properties were studied by ac impedance and cyclic voltammetry measurements, respectively. The solid solution member at x=0.065 in Li_3+5xP_1−xS₄ showed the highest conductivity value of 1.5×10⁻⁴ S cm⁻¹ at 27 °C with negligible electronic conductivity and the activation energy of 22 kJ mol⁻¹ which is characteristic of high ionic conduction state. The extra lithium ions in Li₃PS₄ created by partial substitution of P⁵⁺ for Li⁺ led to the large increase in ionic conductivity. In the solid solution range examined, the minimum conductivity was obtained for the compositions, Li₃PS₄ (x=0.0 in Li_3+5xP_1−xS₄) and Li₄P_0.8S₄ (x=0.2 in Li_3+5xP_1−xS₄); this conductivity behavior is similar to other thio-LISICON family with the general formula, Li_xM_1−yM_y′S₄ (M=Si, Ge, and M′=P, Al, Zn, Ga, Sb). Conduction mechanism and the material design concepts are discussed based on the conduction behavior and the structure considerations.     

Coercivity mechanism in nanophase (Nd–Pr)–Fe–B melt spun alloys

The nucleation mechanism to predict coercivity values in melt-spun exchange-coupled (Nd_1−xPr_x)_yFe_94−yB₆ alloys for various Nd:Pr ratios x, and Fe:RE ratios y, was tested using the dependence of the anisotropy constant K₁ on Pr content x for the minimum nucleation field H_N^min in the modified Brown's equation. Very good agreement was found between experimental data and theoretical values, confirming the predominance of the nucleation of reverse domains over the wall pinning process in the coercivity mechanism of melt spun REFeB alloys.     

Oxygen diffusion and surface exchange in La1−xSrxFe0.8Cr0.2O3−δ (x=0.2, 0.4 and 0.6)

Oxygen tracer diffusion (D*) and surface exchange rate constant (k*) have been measured, using isotopic exchange and depth profiling by secondary ion mass spectrometry (SIMS), in La_1−xSr_xFe_0.8Cr_0.2O_3−δ (x=0.2, 0.4 and 0.6). Measurements were made as a function of temperature (700–1000 °C) and oxygen partial pressure (0.21–10⁻²¹ atm) in dry oxygen, water vapour and water vapour/hydrogen/nitrogen mixtures. At high oxygen activity, D* was found to increase with increasing temperature and Sr content. The activation energies for D* in air are 2.13 eV (x=0.2), 1.53 eV (x=0.4) and 1.21 eV (x=0.6). As the oxygen activity decreases, D* increases as expected qualitatively from the increase in oxygen vacancy concentration. Under strongly reducing conditions, the measured values of D* at 1000 °C range from 10⁻⁸ cm² s⁻¹ for x=0.2 to 10⁻⁷ cm² s⁻¹ for x=0.4 and 0.6. The activation energies determined at constant H₂O/H₂ ratio are 1.21 eV (x=0.2), 1.59 eV (x=0.4) and 0.82 eV (x=0.6).

The surface exchange rate constant of oxygen for the H₂O molecule is similar in magnitude to that for the O₂ molecule and both increase with increasing Sr concentration.     

Lithium insertion to ReO3-type metastable phase in the Nb2O5–WO3 system

Lithium insertion to distorted ReO₃-type metastable solid solution Nb_xW_1−xO_3−x/2 (0≤x<0.25) has been studied by chemical and electrochemical methods. In the course of lithium insertion into tetragonal compounds, transition to a cubic phase was found to occur in the region where values of y (in Li_yNb_xW_1−xO_3−x/2) fall between 0.2 and 0.3, and the phase transition was found to depend on the conditions of the reaction. Changes in OCV and lattice parameters in tetragonal region (y<0.2) were discussed from the viewpoint of the ordering of lithium ions. Also, the component diffusion coefficient of lithium in tetragonal compounds Li_0.1Nb_xW_1−xO_3−x/2 (0≤x≤0.23) was found to increase with niobium content when x≤0.10, and to saturate at 4×10⁻⁹ cm²/s.     

Synthesis and characterization of the Aurivillius phases Bi2 − xPbxSr1 − xNdxNb2O9

The n = 2 Aurivillius phase Bi_{2 − x}Pb_xSr_{1 − x}Nd₂O₉ was successfully synthesized as a ceramic material over the whole range of simultaneous, charge compensated substitution x = 0–1.0. Structural investigations were performed by Rietveld refinement applying different space groups Fmmm and A2₁am, and additionally by X-ray absorption spectroscopy (EXAFS) on the Nd L_III-edge, confirming the accommodation of Nd on the atomic sites of Sr, which implies the substitution of Bi³⁺ by the isoelectronic Pb²⁺. The ferroelectric transition temperature T_c = 270 °C of the substituted powders with x = 0.4 and 1.0 is distinctly reduced compared to the unsubstituted sample with T_c = 450 °C. In temperature resolved powder X-ray diffraction patterns no structural phase transition could be detected.     

Characterization of nonstoichiometric nickel manganite spinels NixMn3−x□3δ/4O4+δ by temperature programmed reduction

Cation deficient spinels Ni_xMn_3−x□_3δ/4O_4+δ (0≤x≤1) have been prepared by thermal decomposition of mixed oxalates Ni_x/3Mn_(3−x)/3(C₂O₄)·nH₂O in air at 623 K. They have been characterised by temperature programmed reduction (TPR) under H₂, the reaction being followed by gravimetric and powder X-ray diffraction measurements. It has been shown that TPR proceeds in several steps. The first steps correspond to the loss of nonstoichiometric oxygen leading to the formation of a stoichiometric oxide. During the following stages the manganese cations are reduced, causing the spinel structure to be destroyed, and the formation of solid solution of NiO in a cubic MnO. Subsequently, Ni²⁺ cations undergo a reduction to metallic nickel, and, finally, a mixture of nonstoichiometric MnO_1−δ and metallic nickel is formed. These oxides contain a high level of vacancies which vary with the nickel content with a maximum of δ≈1 near x=0.6. This nonstoichiometry is ascribed both to the presence of Ni³⁺ and excess of Mn⁴⁺.     

Oxygen permeability of La2Cu(Co)O4+δ solid solutions

Formation of the La₂Cu_1−xCo_xO_4+δ solid solutions with orthorhombic K₂NiF₄-type structure was found to be in the range of 0≤x≤0.30 at temperatures above 1270 K. Incorporating cobalt into the copper sublattice of lanthanum cuprate leads to increasing oxygen hyperstoichiometry and decreasing electrical conductivity. Thermal expansion coefficients of the La₂Cu_1−xCo_xO_4+δ (x=0.02–0.30) ceramics at 470–1100 K were calculated from the dilatometric data to vary in the range (12.2–13.2)×10⁻⁶ K⁻¹. Studying the dependence of oxygen permeation fluxes through La₂Cu(Co)O_4+δ on the membrane thickness demonstrated that the oxygen transport at the thickness values below 1 mm is limited by both surface exchange rate and bulk ionic conductivity. Oxygen permeability of the La₂Cu_1−xCo_xO_4+δ solid solutions was ascertained to increase with cobalt concentration at x=0.02–0.10 and to decrease with further dopant additions, indicating a participation of interstitial oxygen in the ionic transport.     

Defect structure of quenched γ-BICOVOX by combined X-ray and neutron powder diffraction

A detailed investigation of the defect structure of the Co doped BIMEVOX solid electrolyte, Bi₂V_{1 − x}Co_xO_{5.5 − 3x/2} (x = 0.1 and x = 0.2), quenched from high temperature, has been carried out using X-ray and neutron powder diffraction data measured at room temperature. The structure is built up from alternating layers of [Bi₂O₂]_n²ⁿ⁺ and [V_{1 − x}Co_xO_{3.5 − 3x/2}]_n²ⁿ⁻ with disorder limited to the vanadate layer. The ideal V/Co co-ordination is octahedral with corner sharing of equatorial oxygens. The refinements show that the true structure is distorted, with disorder in both apical and equatorial oxygens and oxygen vacancies concentrated in the equatorial positions. Detailed analysis of the oxygen site occupancies reveals two main types of V/Co co-ordination viz. distorted octahedral and distorted tetrahedral. The majority of the sites in both compositions are tetrahedral.     

Very strong interlayer exchange coupling in epitaxial Fe/Fe1−xSix/Fe trilayers (x=0.4–1.0)

Fe/Fe_1−xSi_x/Fe (x=0.4–1.0) wedge-type epitaxial trilayers with improved homogeneity are grown by co-evaporation from two electron-beam sources. The coupling strengths of the bilinear (J₁) and biquadratic (J₂) coupling terms are derived from Brillouin light scattering (BLS) spectra and longitudinal MOKE hysteresis loops. The total coupling strength J=J₁+J₂ increases dramatically with increasing x and reaches values in excess of 6 mJ/m².     

Effect of Pr and Ca substitution on superconductivity in Y(1−x−yPrxCay)Ba2Cu3O7−δ

Pr substituted at constant Ca concentration for Y in (Y_1−x−yPr_xCa_y)Ba₂Cu₃O_7−δ superconductors have been prepared under identical conditions and the temperature dependence of the electrical resistivity of these samples are measured. The resistively determined values of T_c decrease linearly with increasing x (0 ≤ x ≤ 0.2) for constant y = 0.10 and 0.15 which provides convincing evidence that the suppression of superconductivity by Pr is mainly due to magnetic pair breaking. The suppression of superconductivity can also be correlated to the observed changes in oxygen content determined by iodometric analysis and to the average Cu-valences. However, it is found that the observed suppression of T_c cannot be compensated by appropriate hole doping with Ca.     

Electrons and holes in undoped Nd2CuO4

Nd₂CuO_4±δ is the non-superconducting prototype of the Re_2−xM_xCuO₄t−y family (Re=Pr, Nd, Sm and M=Ceor Th) of n-type oxide superconductors. Four-probe DC conductivity, EMF in P(O₂) gradient, and thermopower measurements have been used to characterise its electric transport and defect structure between 300 and 900°C and between 5×10⁻⁴ and 1 atm oxygen partial pressure.

The results show that Nd₂CuO_4±δ can be oxygen under-stoichiometric (with n-type conductivity), near-stoichiometric, and over-stoichiometric (with p-type conductivity) in different T, P(O₂) ranges.     

Temperature dependence of induced magnetic anisotropy in metallic glasses (Fe1 − xCox)78Si10B12

The variations of induced magnetic anisotropy with annealing and measuring temperatures in metallic glasses (Fe_{1 − x}Co_x)₇₈Si₁₀B₁₂ have been measured. It was found that K_u (T) was proportional to Mⁿ_s (T) for T below 200°C, and the index n varied with the cobalt content x and annealing conditions, not being smaller than 3. To the predictions of the existing pair-ordering and single-ion theories, the above results are anomalous. By considering the distributions of exchange integrals and activation energies in metallic glasses, this anomalous behaviour could be explained properly.     

Nax/2Bi1−x/2MoxV1−xO4 and Bi1−x/3MoxV1−xO4 New Scheelite-related phases

New Scheelite-related solid solutions of the compositions Na_x/2Bi_1−x/2Mo_xV_1−xO₄ (0≤x≤1) and Bi_1−x/3 Mo_xV_1−xO₄(0≤x≤0.2) have been synthesised by the substitution of Na and Mo at the A and B sites respectively of the ABO₄ type ferroelastic BiVO₄. The phases were characterised using chemical analysis, powder X-ray diffraction, scanning electron microscopy, EDAX, and Raman spectroscopy. While almost a continuous solid solution is obtained for the series Na_x/2Bi_1−x/2Mo_xV_1−xO₄, the absence of Na at the A-site results only in a narrow stability region for the other series, Bi_1−x/3 Mo_xV_1−xO₄ where 0≤x≤0.2. Raman spectra of selected samples at room temperature also suggest that vanadium and molybdenum atoms are disordered at the tetrahedral sites.     

Magnetic anisotropy in the paramagnetic phase of TbAl2

The magnetic anisotropy of a single crystal of TbAl₂ has been measured by torque magnetometry from below the Curie point up to 170 K, well into the paramagnetic phase. Within a (110) plane the torque can be described by the expression L(θ) = {P sin 2θ} H² + {Q sin 2θ + S sin 4θ} H⁴ + {T sin 4θ} H⁶, where θ is the an gle formed by the magnetization vector with a [001] axis. The first term (in H²) is interpreted as produced by arrays of defects with axial symmetry. The second (in H⁴) and third (in H⁶) terms arise from anisotropic fourth and sixth rank tensor paramagnetic susceptibilities. On the other hand if the anisotropy is described in terms of effective conventional anisotropy constants K₁ and K₂ within the temperature range 90–170 K it is found that both constants change continuously across the Curie temperature and furthermore the [111] direction remains the easy direction in the paramagnetic range. Anisotropy measurements reveal themselves as a sensitive indicator of the level of macroscopic defects in magnetic crystals.     

Studies of lithium intercalation in 3R-WS2

The lithium intercalation into the layered dichalcogenide 3R-WS₂ has been investigated by electrochemical reduction and by chemical reaction in n-butyl lithium solution. Essential results are (a) a charge transfer of nearly 0.6e⁻/W in Li_xWS₂, (b) a small increase of the c-axis parameter of about 0.6%, and (c) a high mobility of the Li⁺-ions. The chemical diffusion coefficient of Li⁺-ions is estimated to be 8 × 10⁻⁹ cm² s⁻¹ in the composition range 0 ≤ x ≤ 0.25. The appearance of a structural transformation from 3R-WS₂ to 2H-Li_xWS₂ is interpreted on grounds of instabilities in the interlayer structure.     

Niobium based tetragonal tungsten bronzes as potential anodes for solid oxide fuel cells: synthesis and electrical characterisation

In this paper we report studies on a range of niobate based tungsten bronzes, with a view to analysing their potential as anode materials in SOFCs. Six systems were studied, (Sr_1−xBa_x)_0.6Ti_0.2Nb_0.8O₃, Sr_0.6−xLa_xTi_0.2+xNb_0.8−xO₃, (Sr_0.4−xBa_x)Na_0.2NbO₃, (Ba_1−xCa_x)_0.6Ti_0.2Nb_0.8O₃, Ba_0.5−xA_xNbO₃ (A=Ca, Sr), and Ba_0.3NbO_2.8, and the electrical conductivities were examined over a range of oxygen partial pressures (10⁻²⁰–1 bar). All the systems showed good conductivity in low oxygen partial pressures, with values as high as 8 S cm⁻¹ at 930°C (P(O₂)=10⁻²⁰ bar). As the oxygen partial pressure was raised the conductivity dropped showing in most cases an approximate [P(O₂)]^−1/4 dependence and good re-oxidation kinetics. Of all the samples studied the (Sr_1−xBa_x)_0.6Ti_0.2Nb_0.8O₃ and (Ba_1−xCa_x)_0.6Ti_0.2Nb_0.8O₃ systems appear most promising for potential use as anode materials in SOFCs.     

Quenching of spin fluctuations by high magnetic fields

The quenching of spin fluctuations by magnetic fields has been observed in heat capacity and electrical resistivity measurements at low temperatures for a series of highly exchange enhanced magnetic materials. These include: the weak itinerant electron ferromagnets Sc₃In, Zr_1−xHf_xZn₂ (0 x 0.2) and Ni₃Al; the strong Pauli paramagnets RCo₂ (R = Sc, Y and Lu), TiBe₂ and Pd_1−xNi_x (0 x 0.01); and the heavy fermion systems CeSn₃, CeSi_x (x ≈ 1.85) an d UAl₂. The reported quenching of spin fluctuations in scandium and palladium by magnetic fields is reviewed, and it appears that the initial observations and conclusions are incorrect, and that fields greater than 10 and 40 T, respectively, will be necessary to quench spin fluctuations in these metals. The behaviors of these spin fluctuators have been grouped into six classes.