单模光纤与Ti:LiNbO3单模平面光波导端面激励耦合的研究

本文报导一个单模光纤与单模Ti扩散LiNbO3光波导的端面耦合及固定连接实验研究.利用电弧烧熔法在单模光纤端面上制成了微透镜,改善了模场匹配程度,采用二维硅V形糟,提高了光纤与波导的对准精度。     

Mismatch considerations in laser diode to monomode fiber excitation via a hemispherical lens on the elliptical core fiber tip

We present what, as per our knowledge, is the first theoretical investigation of the coupling efficiency of a laser diode to a single-mode fiber via a hemispherical microlens on the elliptical core fiber tip in presence of possible transverse and angular misalignments. Using the ABCD matrix for refraction by a hemispherical lens on the tip of an elliptical core single-mode fiber, we present analytical expressions of such coupling efficiencies and investigate the corresponding losses due to possible transverse and angular misalignments. The concerned calculations involve little computations. Our analysis takes into consideration the limited aperture provided by the hemispherical lens. The results should be useful in optimum launch optics for designing suitable hemispherical microlenses on the tip of elliptical core fibers or circular core fibers which suffer from noncircularity.     

Multimode fiber devices with single-mode performance

A taper transition can couple light between a multimode fiber and several single-mode fibers. If the number of single-mode fibers matches the number of spatial modes in the multimode fiber, the transition can have low loss in both directions. This enables the high performance of single-mode fiber devices to be attained in multimode fibers. We report an experimental proof of concept by using photonic crystal fiber techniques to make the transitions, demonstrating a multimode fiber filter with the transmission spectrum of a single-mode fiber grating.     

扩芯光纤原理及其在光器件耦合中的应用

介绍了两种可以增大单模光纤模场直径并出射准直平行光束的扩芯光纤(ECF)的原理和制作方法。分析了单模光纤熔接渐变折射率多模光纤法通过改变渐变折射率多模光纤的长度和自聚焦参量实现模场扩大缩小的原理,制作的扩芯光纤模场直径扩大到16．6μm,出射光束平行效果较好,轴向耦合容限比单模光纤扩大了近6倍。加热扩芯光纤则是通过控制加热温度和加热时间直接使单模光纤掺杂物质发生扩散,从而实现扩束和光束准直,模场直径达到15．4μm,横向、轴向耦合容限都比单模光纤有很大提高。因此扩芯光纤可以简化单模光纤的耦合对准过程,用来制作新型的单模光纤或掺铒光纤连接器,也可以用于其它光器件中与单模光纤的准直。     

Low-loss coupling between two single-mode optical fibers with different mode-field diameters using a graded-index multimode optical fiber

We present a method for ultra-low-loss coupling between two single-mode optical fibers with different mode-field diameters using multimode interference in a graded-index multimode optical fiber. We perform a detailed analysis of the interference effects and show that the graded-index fiber can also be used as a beam expander or condenser. The results are important for devices in which optical fibers with different mode-field diameters are coupled in series, such as in ultra-short-pulse fiber ring lasers, or in optical fiber communication links.     

基于非球面透镜的空间光场光纤耦合系统研究

针对全光纤激光雷达中空间光场与单模光纤的耦合问题,设计了基于非球面透镜的望远镜光纤耦合系统.利用ZEMAX软件以单模光纤耦合效率为优化目标对其结构参量进行优化设计,然后分别用LED和激光器作为光源进行初步实验,比较直接耦合和非球面透镜耦合效果.实验结果表明,采用非球面透镜耦合可使多模光源的耦合效率比直接耦合增加约47%,与仿真结果45%非常接近,且不同芯径耦合光功率之比大略等于芯径比平方;而该耦合方式可使单模光源的耦合效率增加约20%,且耦合进不同小芯径光纤的耦合效率之比约为其芯径比平方的2.4倍,这对构建全光纤转动喇曼激光雷达系统具有重要意义.     

三包层WⅠ和WⅡ型单模光纤波导色散特性的研究

研究了三包层WⅠ和WⅡ型单模光纤的波导色散特性。结果发现在相同条件下，三包层WⅠ和WⅡ型单模光纤零色散点的调节范围比传统的双包层W型单模光纤明显增大。详细分析了几何参量P、Q和光学参量R1、R2对单模传输时的波导色散特性和低次模截止频率的影响。所得的研究结果为获得更为理想的色散补偿、色散平坦光纤及设计新型无源光器件提供了重要的依据。计算波导色散的方法可推广到多包层光纤。     

Fiber Fourier optics

The Fourier transform of a coherent optical image can be evaluated physically by use of a single lens plus free-space propagation, thereby providing the basis for the field of Fourier optics. I point out that one can similarly evaluate the discrete Fourier transform of a sampled or pixelated optical array physically by passing the discrete array amplitudes through a network of single-mode fibers or optical waveguides. A passive optical network that evaluates the fast Fourier transform of a coherent array can be fabricated by use of (N/2)log(2)[N] optical 3-dB couplers plus small added phase shifts. Implementing such networks in fiber or integrated optical form could provide the basis for a possible technology of fiber Fourier optics.     

Refractive-index profiling of azimuthally asymmetric optical fibers by microinterferometric optical phase tomography

Accurate nondestructive refractive-index profiling is needed in the modeling, design, and manufacturing of optical fibers and fiber devices. Most profile measurement techniques cannot correctly characterize fibers with small or irregular refractive-index variations over their cross sections. Microinterferometric optical phase tomography (MIOPT) is a technique that allows measurement of fiber refractive-index profiles exhibiting such variations. We present the first demonstration, to our knowledge, of MIOPT. The profile of a polarization-maintaining fiber is measured by MIOPT and shown to be in agreement with (destructive) fiber end-face measurements. MIOPT is also applied to the limiting case of a symmetric single-mode fiber.     

Pigtailing the high-Q microsphere cavity: a simple fiber coupler for optical whispering-gallery modes

We demonstrate a simple method for efficient coupling of standard single-mode optical fibers to a high- Q optical microsphere cavity. Phase-matched excitation of whispering-gallery modes is provided by an angle-polished fiber tip in which the core-guided wave undergoes total internal reflection. In the experimental setup, which included a microsphere with both an input and an output coupler, the total fiber-to-fiber transmission at resonance reached 23% (total insertion loss, 6.3 dB), with loaded quality factor Q>/=3x10(7) and unloaded Q approximately 1.2x10(8) at 1550 nm. A simple pigtailing method for microspheres permits their wider use in fiber optics and photonics devices.     

Fabrication of microgratings on the ends of standard optical fibers by the electrostatic self-assembly monolayer process

The electrostatic self-assembly monolayer process has been utilized for what is believed to be the first time to deposit quarter-wavelength stacks on the end faces of cleaved and polished optical fibers. Standard multimode optical fibers as well as single-mode optical fibers were used as substrates with different coating materials to fabricate broadband filters, and the experimentally measured spectral responses of these devices are shown. These optical filter structures were employed to develop chemical sensors that use an unperturbed reference wavelength to normalize the output signal.     

Excitation of cladding modes in photonic crystal fibers by flexural acoustic waves

We report the excitation by flexural acoustic waves of an individual cladding mode in a single-mode photonic crystal fiber. The propagation constant and the field distributions of the mode have been investigated by use of this technique. The results give the basis for developing a family of acousto-optic devices based on photonic crystal fibers.     

Laser diode to single-mode circular core dispersion-shifted/dispersion-flattened fiber excitation via hyperbolic microlens on the fiber tip: Prediction of coupling efficiency by ABCD matrix formalism

The formulated ABCD matrix formalism is employed to prescribe analytical expression of coupling efficiency of a laser diode to single-mode circular core dispersion-shifted as well as dispersion-flattened fiber via hyperbolic microlens on the tip of the fiber. We assume that field distribution in case of both the source and the fiber is one parameter Gaussian type. For maximum excitation efficiency, it is required that the lens transmitted spot size of the source should match with the spot size of the fiber. Further, as regards the spot size of the fiber, we use Petermann II spot size in order to take care of non Gaussian nature of field of such fibers and to make the estimations more realistic thereby. The investigations are carried out for two different wavelengths 1.3 and 1.5 μm. Our simple method predicts the concerned coupling optics excellently and the necessary evaluations require little computations. This simple but accurate technique is expected to benefit the system designers who work in the field of optical technology.     

Power transfer characteristics among N parallel single-mode optical fibers

Based on the coupled-mode theory, the power transfer among “- - - -” arranged parallel single-mode optical fibers has been investigated. The analysis shows that the distances between each two of the N fiber centers have effects on the coupling coefficient and power transfer. The solution of the coupled-equations for three parallel single-mode optical fibers is given, and is studied for different initial conditions comparatively. Numerical simulations show that power transfer will be periodical during coupling among parallel single-mode optical fibers. These results can be extended to multi-parallel single-mode optical fibers.     

多根平行光纤的功率转移特性分析

基于模式耦合理论,研究了呈一字型排列的多根平行单模光纤间的功率转移,分析了光纤间距对耦合系数和功率转移的影响,给出了三根平行单模光纤耦合方程的解,针对不同的初始条件进行了比较分析.数值计算表明,呈一字型排列的多根平行单模光纤间的功率成一定周期转移.     

Polarization-independent grating couplers for silicon-on-insulator nanophotonic waveguides

We propose the use of subwavelength structures in a waveguide grating to achieve polarization-independent coupling of light between an optical fiber and a silicon-on-insulator (SOI) optical waveguide. The subwavelength structure allows the mode effective indices of the TE and TM modes in the grating section to be precisely engineered. We calculate that coupling efficiency of over 64% is possible using the proposed design for polarization-independent coupling between single-mode optical fibers and SOI nanophotonic waveguides.     

High-energy single-transverse-mode Q-switched fiber laser based on a multimode large-mode-area erbium-doped fiber

We demonstrate that appropriately designed doped multimode fibers provide robust single-mode output when used within a fiber laser cavity. Using a novel large-mode-area fiber, we demonstrate what we believe to be record single-mode (M(2) <1.2) pulse energies of >0.5 mJ from a Q -switched fiber laser and even higher pulse energies (as high as 0.85 mJ) with slightly compromised spatial-mode quality (M(2)<2.0) . This approach offers significant scope for extending the range of single-mode output powers and energies that are achievable from fiber-laser-amplifier systems.     

Laser machining of micro-lenses on the end face of single-mode optical fibers

Focussing of the output beam of optical fibers is required in a variety of applications. We present a laser micro-machining technique for the fabrication of micro-lenses directly on the end face of single-mode silica fibers using a F₂-laser processing station. A uniform ablation spot is projected onto the fiber end face and steered along a trajectory of overlapping concentric circles. The lens profile is controlled by the spot size, the number of circles in the trajectory, and the scanning speed. Strong 157 nm absorption by the silica glass facilitates precise structuring without micro-crack formation in both cases. The surface quality of the fiber-lenses is characterized by AFM and SEM and reveals ∼ 100 nm rms roughness with good control of the surface profile. Optical beam profiling indicates the possibility for creating spot sizes of 1/5 the core diameter at the fiber output. PACS 42.81.Wg