Phosphoric-Acid Retention in High-Temperature Proton-Exchange Membranes

Great efforts have been conducted to develop high temperature proton exchange membrane fuel cell (HT-PEMFC) due to its features of enhanced electrocatalyst reactivity, simplified hydrothermal management system and high CO tolerance of catalysts, and remarkable progress has been achieved. However, the easy leaching of phosphoric acid (PA) from the membranes during operation limits its commercial scale-up in complicated environments. This concept here mainly focuses on the recent developments for mitigation of PA loss in PEMs. The probable mechanisms of PA loss are proposed. The approaches to improve PA retention for example via introduction of phosphonic acid by covalent bond, using ion-pairs interaction and siphoning effect, and blending with inorganic nanoparticles are described in detail. Among these strategies, the siphoning effect from the intrinsic microporous PEMs is the most efficient and enables the cell to operate flexibly within a broad temperature range. Therefore, this concept may provide new ideas for the scientists to retain PA, to improve the cell performance and expand the potential applications of PA doped PEMs at elevated humidity and wide temperature range.     

Novel sulfonated block copolymer containing pendant alkylsulfonic acids: Syntheses,unique morphologies,and applications in proton exchange membrane

In this article, we report the syntheses and characterizations of a series of novel block polyelectrolytes, poly(styrene‐block‐sulfonated hydroxystyrene) (PS‐b‐sPHS), containing pendant sulfonic acid groups attached to the backbone via propyl spacers in the sPHS domain. PS‐b‐sPHS with various compositions were synthesized via anionic polymerization and the following analogous chemistry to achieve accurate control of molecular weight (M_w), narrow polydispersity and high degree of sulfonation. Proton exchange membranes (PEMs) were prepared from PS‐b‐sPHS with sulfonic acids in either potassium salts or tetra‐alkylammonium salts via solvent casting and following treatments. Some unique morphologies, such as hallow channels and lamellar arrangement of strings of beads, were observed as a consequence of equilibrium between microphase separation and columbic interactions between polyelectrolytes. The transportation properties were found to closely relate to the morphologies of the PEMs. The combination of microphase separation of block polyelectrolytes and freedom of movement of pendent alkylsulfonic acids was demonstrated to effectively enhance the proton transport and suppress the methanol crossover for the PEMs, leading to the selectivity higher than Nafion 117 by five times at most. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Segmented sulfonated poly(arylene ether sulfone)‐b‐polyimide copolymers for proton exchange membrane fuel cells. I. Copolymer synthesis and fundamental properties

Segmented disulfonated poly(arylene ether sulfone)‐b‐polyimide copolymers based on hydrophilic and hydrophobic oligomers were synthesized and evaluated for use as proton exchange membranes (PEMs). Amine terminated sulfonated poly (arylene ether sulfone) hydrophilic oligomers and anhydride terminated naphthalene based polyimide hydrophobic oligomers were synthesized via step growth polymerization including high temperature one‐pot imidization. Synthesis of the multiblock copolymers was achieved by an imidization coupling reaction of hydrophilic and hydrophobic oligomers oligomers in a m‐cresol/NMP mixed solvent system, producing high molecular weight tough and ductile membranes. Proton conductivities and water uptake increased with increasing ion exchange capacities (IECs) of the copolymers as expected. The morphologies of the multiblock copolymers were investigated by tapping mode atomic force microscopy (TM‐AFM) and their measurements revealed that the multiblock copolymers had well‐defined nano‐phase separated morphologies which were clearly a function of block lengths. Hydrolytic stability test at 80 °C water for 1000 h showed that multiblock copolymer membranes retained intrinsic viscosities of about 80% of the original values and maintained flexibility which was much improved over polyimide random copolymers. The synthesis and fundamental properties of the multiblock copolymers are reported here and the systematic fuel cell properties will be provided in a separate article. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4879–4890, 2007     

A review on the role of proton exchange membrane on the performance of microbial fuel cell

Proton exchange membranes (PEMs) are the most frequently used separators in microbial fuel cells (MFCs). The role of proton transportation in MFC performance makes PEMs one of the most important components in the cell. The effect of PEMs in MFC performance is commonly determined according to generated power density and coulombic efficiency. Nafion is the commonly used membrane in MFCs, but there are still a number of problems associated with the use of Nafion including oxygen transfer rate, cation transport and accumulation rather than protons, membrane fouling and substrate loss. Moreover, additional problems can also be attributed to the effect of PEMs including internal resistance and pH change in MFCs. Recent developments in PEM performance are attributed to two categories including utilization of other types of membranes and improvements in Nafion by pre‐treatment methods. Copyright © 2014 John Wiley & Sons, Ltd.     

Investigation of proton conductivity of anhydrous proton exchange membranes prepared via grafting vinyltriazole onto alkaline‐treated PVDF

This work uses a simple “grafting through” approach in the preparation of anhydrous poly(vinylidene fluoride) (PVDF)‐g‐PVTri polymer electrolyte membranes (PEMs). Alkaline‐treated PVDF was used as a macromolecule in conjunction with vinyltriazole in the graft copolymerization. The obtained polymer was subsequently doped with triflic acid (TA) at different stoichiometric ratios with respect to triazole units and the anhydrous PEMs (PVDF‐g‐PVTri‐(TA)_x) were prepared. All samples were characterized by FTIR and ¹H NMR. The composition of PVDF‐g‐PVTri was determined by energy dispersive spectroscopy. Thermal properties of the membranes were examined by thermogravimetric analysis and differential scanning calorimetry. The surface roughness and morphology of the membranes were studied using atomic force microscopy, X‐ray diffraction, and scanning electron microscopy. PVDF‐g‐PVTri‐(TA)₃ (C3‐TA₃) with a degree of grafting of 47.22% showed a maximum proton conductivity of 0.09 S cm^?1 at 150 °C and anhydrous conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1885–1897     

Water sorption and diffusion coefficients of protons and water in PVDF-g-PSSA polymer electrolyte membranes

Water sorption properties, proton NMR spectra, and diffusion of water and protons in poly(vinylidene fluoride)-graft-polystyrene sulfonic acid (PVDF-g-PSSA) polymer electrolyte membranes were studied. Sorption curves for the membranes with different degrees of grafting in protonated and Na⁺ form were measured by equilibrating the membranes over saturated salt solutions. The membrane water content was found to be sensitive to changes in relative humidity (RH). The water/sulfonic acid ratio λ for the protonated samples was around 2 at 20% RH and increased to λ ∼ 30 at 100%. Proton NMR, pulsed field gradient proton NMR (PFG-NMR), and impedance measurements were made on membranes with different λ. In the proton NMR spectra only one peak was found, originating from the water in the membrane. The chemical shift of the peak was found to be dependent on the counterion and the water content. The water self-diffusion coefficients D_H2O, measured by PFG-NMR, increased with degree of grafting and water content of the membranes. The proton conductivity and the calculated proton mobility decreased more steeply than the D_H2O with decreasing water content. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2893–2900, 1999     

Viscoelastic effects in cutting of elastomers by a sharp object

The cutting behavior of elastomers by a sharp object was investigated using various elastomers such as acrylonitrile–butadiene rubber (NBR), styrene–butadiene rubber (SBR), and natural rubber (NR). The effects of crosslinking density, cutting rate, and temperature on the cutting energy of elastomers were investigated. The cutting behavior of swollen elastomers was also investigated. It was found that the cutting energy increased as the molecular weight between crosslinks increased. It was also found that the cutting energies of various elastomers did not yield a single line. Moreover, even in the threshold condition of cutting process, the cutting energy was much higher than the threshold fracture energy. These results suggest that the cutting behavior cannot be explained by only a C C bond rupture process, but it includes other energy dissipation processes. The curves for cutting energies obtained at different cutting rates and temperatures were well superimposed on a single master curve when they were shifted using the WLF (Williams, Landel, and Ferry) equation. Therefore, it is supposed that the cutting of elastomers by a sharp object includes viscoelastic energy dissipation process and is the viscoelastic behavior. It was also found that the variation of cutting energy over a considerable range of effective rates was smaller than that of the tear energy. It is attributed to the fact that the change of the crack tip diameter, i.e., roughening or reduction, was restricted by the diameter of razor blade. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1283–1291, 1998     

直接甲醇燃料电池用PEMs的研究进展

本文介绍了用于直接甲醇燃料电池(DMFCs)的质子交换膜(PEMs)的工作原理与性能要求。讨论了影响DMFCs国PEMs的甲醇渗透性能的因素。综述了Nation、改性Nafion膜以及其它新品种膜的研究进展。     

Novel sulfonated poly (ether ether ketone)/silica coated carbon nanotubes high‐performance composite membranes for direct methanol fuel cell

The major risk of using carbon nanotubes (CNTs) to modify proton exchange membranes (PEMs) in fuel cells is possible short‐circuiting due to the excellent electrical conductivity of CNTs. In this article, silica‐coated CNTs (SiO₂@CNTs) were successfully prepared by a simple sol–gel process and then used as a new additive in the preparation of sulfonated poly (ether ether ketone) (SPEEK)‐based composite membranes. The insulated and hydrophilic silica coated on the surface of CNTs not only eliminated the risk of short‐circuiting, but also enhanced the interfacial interaction between CNTs and SPEEK, and hence promoted the homogeneous dispersion of CNTs in the SPEEK matrix. Moreover, compared to the methanol permeability of the pure SPEEK membrane (3.42 × 10^?7 cm² s^?1), the SPEEK/SiO₂@CNT composite membrane with a SiO₂@CNT loading of 5 wt% exhibits almost one order of magnitude decrease of methanol crossover, while the proton conductivity still remained above 10^?2 S cm^?1 at room temperature. The obtained results expose the possibility of SPEEK/SiO₂@CNT membranes to be served as high‐performance PEMs in direct methanol fuel cells. Copyright © 2015 John Wiley & Sons, Ltd.     

Membranes from poly(aryl ether)‐based ionomers containing multiblock segments of randomly distributed nanoclusters of 18 sulfonic acid groups

Multiblock copolymers 1a (M_n = 31,500–47,400) of sulfonated poly(aryl ether)s were synthesized by polycondensation of 4,4′‐difluorobenzophenone (DFBP), bis(4‐hydroxyphenyl)sulfone (BHPS), and an hydroxy‐terminated sulfonated oligomer, which was synthesized from DFBP and 2,2′,3,3′,5,5′‐hexaphenyl‐4,4′‐dihydroxybiphenyl a . The copolymerization of trimeric monomer b with DFBP and BHPS gave a series of copolymers 1b (M_n = 26,200–45,900). The copolymers were then sulfonated with chlorosulfonic acid to give ionomers 3a with hydrophilic multiblock segments and ionomers 3b with segments containing clusters of 18 sulfonic acid groups. The proton exchange membranes cast from ionomers 3a and 3b were characterized with regard to thermal stability, water uptake, proton conductivity, and morphology. Transmission electron microscopy images of 3a‐1 and 3b‐1 revealed a phase separation similar to that of Nafion that may explain their higher proton conductivities compared with randomly sulfonated copolymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4762–4773, 2009     

Nanocomposite hydrogels: Fracture toughness and energy dissipation mechanisms

In this study, fracture toughness of nanocomposite hydrogels is quantified, and active mechanisms for dissipation of energy of nanocomposite hydrogels are ascertained. Poly(N,N‐dimethylacrylamide) nanocomposite hydrogels are prepared by in situ free radical polymerization with the incorporation of Laponite, a hectorite synthetic clay. Transmission electron microscopy proves exfoliation of clay platelets that serve as multifunctional crosslinkers in the created physical network. Extraordinary high fracture energies of up to 6800 J m^?2 are determined by the pure shear test approach, which shows that these soft and stretchable hydrogels are insensitive to notches. In contrast to single‐ and double‐network hydrogels, dynamic mechanic analysis and stress relaxation experiments clarify that significant viscoelastic dissipation occurs during deformation of nanocomposite hydrogels. Similar to double‐network hydrogels, crack tip blunting and plastic deformation also contribute to the observed massive fracture energies. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1763–1773     

Multiblock poly(Phenylene ether nitrile)s with pendant sulfoalkoxyl side chain for H2/air fuel cells at low humidity condition

A series of multiblock poly(phenylene ether nitrile)s with pendant sulfoalkoxyl side chains have been developed as proton exchange membranes for fuel cells. The membranes were obtained by a solution casting method and exhibited good thermal stability, flexibility, and mechanical strength. The membranes displayed well‐developed microphase separation, which largely contributed to their excellent ion conduction ability. One of the new membranes with a low ion exchange capacity of 1.57 mequiv g^?1 showed higher proton conductivity than Nafion 212 over the entire RH range (30–95%). The maximum power output generated in a single cell test reached up to 0.754, 0.640, and 0.414 W cm^?2 at 70 °C under 80%, 50%, and 30% RH conditions, respectively. The current density of the membrane obtained at 0.6 V (I _0.6) was as high as 640 mA cm^?2, which was much higher than that of Nafion 212 (375 mA cm^?2 at 30% RH), suggesting its superiority for a more rapid system start‐up. Furthermore, the in situ durability test at 50% RH was performed at a constant current loading, and the membrane did not show any significant voltage reduction over the 400 h testing period. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1940–1948     

Synthesis and characterization of sulfonated poly(benzoxazole ether ketone)s by direct copolymerization as novel polymers for proton-exchange membranes

A new series of sulfonated poly(benzoxazole ether ketone)s (SPAEKBO-X) were prepared by the aromatic nucleophilic polycondensation of 4,4′-(hexafluoroisopropylidene)-diphenol with 2,2′-bis[2-(4-fluorophenyl)benzoxazol-6-yl]hexafluoropropane and sodium 5,5′-carbonylbis-2-fluorobenzenesulfonate in various ratios. Fourier transform infrared and ¹H NMR were used to characterize the structures and sulfonic acid contents of the copolymers. The copolymers were soluble in N-methyl-2-pyrrolidinone, N,N-dimethylacetamide, and N,N-dimethylformamide and could form tough and flexible membranes. The protonated membranes were thermally stable up to 320 °C in air. The water uptake, hydrolytic and oxidative stability, and mechanical properties were evaluated. At 30–90 °C and 95% relative humidity, the proton conductivities of the membranes increased with the sulfonic acid content and temperature and almost reached that of Nafion 112. At 90–130 °C, without external humidification, the conductivities increased with the temperature and benzoxazole content and reached above 10⁻² S/cm. The SPAEKBO-X membranes, especially those with high benzoxazole compositions, possessed a large amount of strongly bound water (>50%). The experimental results indicate that SPAEKBO-X copolymers are promising for proton-exchange membranes in fuel cells, and their properties might be tailored by the adjustment of the copolymer composition for low temperatures and high humidity or for high temperatures and low humidity; they are especially promising for high-temperature applications. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2273–2286, 2007     

Synthesis of poly(arylene ether sulfone)‐block‐sulfonated polybutadiene: the selective post‐sulfonation of block copolymers as proton exchange membranes

A series of poly(arylene ether sulfone)‐block‐sulfonated polybutadiene (PAES‐b‐sPB) with different ion exchange capacities (IECs) were synthesized and evaluated as proton exchange membranes (PEMs) for possible applications in fuel cells. These sulfonated block copolymers were synthesized via condensation reaction between modified PAES and PB prepolymers, followed by selective post‐sulfonation of PB blocks using acetyl sulfate as the sulfonating reagent. The sulfonic groups were only attached onto PB blocks due to the high reactivity of double bonds to acetyl sulfate. The success of synthesis and selective post‐sulfonation were all confirmed by the Fourier transform infrared (FT‐IR) and nuclear magnetic resonance (NMR) spectra. PAES‐b‐sPB had good film‐forming ability and thermal stability. Mechanical properties of membranes varied with the sulfonation. The presence of sulfonic groups increased the tensile strength and Young's modulus but decreased the elongation at break. Transmission electron microscopy (TEM) images showed large ionic aggregates in membranes. Phase separation as well as the interconnected sulfonate groups which only localized on flexible PB blocks led to these ionic domains. The proton conductivity increased with the increasing IEC and temperature. With relatively low IEC, most membranes still exhibited sufficient proton conductivity. The above results indicated this strategy could be a prospective choice to prepare novel PEMs. Copyright © 2010 John Wiley & Sons, Ltd.     

2-取代咪唑衍生物掺杂高温非水用Nafion质子交换膜的制备和性能

高温质子交换膜燃料电池所面临的一个主要技术障碍是高温低湿度环境下能够具有满足电池工作条件的膜的制备.本文通过所合成的2-取代咪唑衍生物与全氟磺酸树脂的掺杂,采用溶液重铸法制备了可以在高温无水条件下工作的质子交换膜.通过2-位疏水基团的接枝,实现了非水质子传导介质的咪唑环在膜内的固定,所制备的复合质子交换膜的导质子率在160℃无水条件下达到6.8×10^-3Scm^-1;而且相比全氟磺酸均质膜,其热稳定性也有所提高.采用静电力显微镜观察到了所制备的复合质子交换膜内相互连接的离子团簇的形成;结合其质子传导活化能,提出了所制备的复合质子交换膜在120℃以下质子传导以跳跃方式为主;在120℃以上,则以咪唑环的＂钟摆＂形式实现质子在膜内的传输.     

Block copolystyrene derivatives having flexible alkylsulfonated side chains and hydrophobic alkoxy chains as a proton exchange membrane for fuel cell application

A series of block copolystyrene derivatives, poly{[4‐(4‐sulfobutyloxy)styrene]_x‐block‐[4‐(n‐butoxystyrene)]_y} (PSBOS_x‐b‐PnBOS_y), containing a flexible alkylsufonated side chain and hydrophobic alkoxy chain with various ion exchange capacities (IECs) have been synthesized based on living anionic polymerization. The resulting crosslinked membranes were prepared using 4,4′‐methylene‐bis[2,6‐bis(hydroxyethyl)phenol] as the crosslinker in the presence of methanesulfonic acid. The crosslinked PSBOS_2.2‐b‐PnBOS₁ membrane with IEC of 2.89 mequiv g^?1 displays a high proton conductivity (0.01 S cm^?1) at 30% relative humidity and 80 °C, which is comparable to that of Nafion. The well‐developed phase separation and the continuous hydrophilic domains in the crosslinked PSBOS_2.2‐b‐PnBOS₁ membranes have been observed in a transmission electron microscope image. Moreover, the dynamic mechanical analysis measurement and Fenton's reagent testing show that the crosslinked PSBOS_x‐b‐PnBOS_y membranes have good mechanical properties and oxidative stability. These results indicate that the introduction of flexible alkylsulfonated side chains to the polystyrene main chains positively affect both the proton conductivity and oxidative stability. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Proton transportation in an organic–inorganic hybrid polymer electrolyte based on a polysiloxane/poly(allylamine) network

A new class of proton‐conducting polymer was developed via the sol–gel process from amino‐containing organic–inorganic hybrids by the treatment of poly(allylamine) with 3‐glycidoxypropyltrimethoxysilane doped with ortho‐phosphoric acid. The polymer matrix contains many hydrophilic sites and consists of a double‐crosslinked framework of polysiloxane and amine/epoxide. Differential scanning calorimetry results suggest that hydrogen bonding or electrostatic forces are present between H₃PO₄ and the amine nitrogen, resulting in an increase in the glass‐transition temperature of the poly(allylamine) chain with an increasing P/N ratio. The ³¹P magic‐angle spinning NMR spectra indicate that three types of phosphate species are involved in the proton conduction, and the motional freedom of H₃PO₄ is increased with increasing P/N ratios. The conductivity above 80 °C does not drop off but increases instead. Under a dry atmosphere, a high conductivity of 10^?3 S/cm at temperatures up to 130 °C has been achieved. The maximum activation energy obtained at P/N = 0.5 suggests that a transition of proton‐conducting behavior exits between Grotthus‐ and vehicle‐type mechanisms. The dependence of conductivity on relative humidity (RH) above 50% is smaller for H₃PO₄‐doped membranes compared with H₃PO₄‐free ones. These hybrid polymers have characteristics of low water content (23 wt %) and high conductivity (10^?2 S/cm at 95% RH), making them promising candidates as electrolytes for fuel cells. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3359–3367, 2005     

Influence of adjusted hydrophilic–hydrophobic lengths in sulfonated multiblock copoly(ether sulfone) membranes for fuel cell application

Sulfonated multiblock copoly(ether sulfone)s applicable to proton exchange membrane fuel cells (PEMFCs) were synthesized by the coupling reaction of the hydroxyl‐terminated hydrophilic and hydrophobic oligomers with different lengths in the presence of highly reactive decafluorobiphenyl (DFB) as a chain extender to investigate the influence of each length on the membranes' properties, such as water uptake, proton conductivity, and morphology. Multiblock copolymers with high molecular weights (M_n > 50,000, M_w > 150,000) were obtained under mild reaction conditions. The resulting membranes demonstrated good oxidative stability for hot Fenton's reagent and maintained high water uptake (7.3–18.7 wt %) under a low relative humidity (50% RH). Proton conductivity of all membranes at 80 °C and 95% RH was higher than that of Nafion 117 membrane, and good proton conductivity of 7.0 × 10^?3 S/cm was obtained at 80 °C and 50% RH by optimizing the oligomer lengths. The surface morphology of the membranes was investigated by tapping mode atomic force microscopy (AFM), which showed that the multiblock copolymer membranes had a clearer surface hydrophilic/hydrophobic‐separated structure than that of the random copolymer, and contributed to good and effective proton conduction. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7332–7341, 2008     

Synthesis of proton‐conducting membranes by the utilization of preirradiation grafting and atom transfer radical polymerization techniques

The atom transfer radical polymerization (ATRP) of styrene onto poly(vinylidene fluoride)‐graft‐poly(vinylbenzyl chloride) (PVDF‐g‐PVBC) membranes was investigated. Novel membranes were designed for fuel‐cell applications. The benzyl chloride groups in the PVDF‐g‐PVBC membranes functioned as initiators, and a Cu‐based catalytic system with the general formula Cu(n)X_n/ligand [where X is Cl or Br and the ligand is 2,2′‐bipyridyl (bpy)] was employed for the ATRP. In addition, 10 vol % dimethylformamide was added for increased solubility of the catalyst complex in styrene. The system was homogeneous, except for the membrane, when the initiator/copper halide/ligand/monomer molar ratio was 1/1/3/500. As anticipated, the fastest polymerization rate of styrene was observed with the copper bromide/bpy‐based catalyst system. The reaction rate was strongly temperature‐dependent within the studied temperature interval of 100–130 °C. The degree of grafting increased linearly with time, thereby indicating first‐order kinetics, regardless of the polymerization temperature. Furthermore, 120 °C was the maximum polymerization temperature that could be used in practice because the membrane structure was destroyed at higher temperatures. The degree of styrene grafting reached 400% after 3 h at 120 °C. Such a high degree of grafting could not be reached with conventional uncontrolled radiation‐induced grafting methods because of termination reactions. On the basis of an Arrhenius plot, the activation energy for the homogeneous ATRP of styrene was 217 kJ/mol. The prepared membranes became proton‐conducting after sulfonation of the polystyrene grafts. The highest conductivity measured for the prepared membranes was 70 mS/cm, which is comparable to the values normally measured for commercial Nafion membranes. The scanning electron microscopy/energy‐dispersive X‐ray results showed that the membranes had to be grafted through the matrix with both PVBC and polystyrene to become proton‐conducting after sulfonation. In addition, PVDF‐g‐[PVBC‐g‐(styrene‐block‐tert‐butyl acrylate)] membranes were also synthesized by ATRP. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 591–600, 2002; DOI 10.1002/pola.10146     

离子型交联磺化聚酰亚胺质子交换膜的制备及高温燃料电池性能

以2,2′-双(4-磺基苯氧基)联苯二胺、 2-(4-氨基苯基)-5-氨基苯并咪唑和1,4,5,8-萘四甲酸二酐为单体, 通过逐步聚合和溶液成膜法制备了离子型交联磺化聚酰亚胺质子交换膜(SPI PEMs). SPI PEMs具有优异的机械性能和耐水解稳定性, 在高离子交换容量和高湿度下具有和NR212相当的质子传导性能. 电池工作温度为90 ℃时, 高加湿条件下, n(BSPOB)/n(DABI)为5/2的离子型交联SPI PEM(M1)的最大输出功率密度(W_max)为 0.93 W/cm², 高于NR212的0.86 W/cm². 当电池温度提高到110 ℃时, 所有PEMs的电池性能显著下降, M1的W_max为0.54 W/cm², 明显高于共价型交联的SPI PEM. 离子型交联的SPI PEM在110 ℃下300 h的开路电压(OCV)耐久性降低了约10%, 远高于NR212.