A direct and rapid leaf water extraction method for isotopic analysis

Isotopic measurements of leaf water have provided insights into a range of ecophysiological and biogeochemical processes, but require an extraction step which often constitutes the major analytical bottleneck in large-scale studies. Current standard procedures for leaf water analysis are based on cryogenic vacuum or azeotrophic distillation, and are laborious, require sophisticated distillation lines and the use of toxic materials. We report a rapid technique based on centrifugation/filtration of leaf samples pulverised in their original sampling tubes, using a specifically adapted, simple apparatus. The leaf water extracts produced are suitable for isotopic analysis via pyrolysis gas chromatography isotope ratio mass spectrometry (PYR/GC/IRMS). The new method was validated against cryogenic vacuum distillation and showed an overall accuracy of +/-0.5 per thousand (nine grouped comparisons, n = 110) over a range of 21 per thousand. Effects due to the presence of soluble carbohydrates were near the detection limits for most samples analysed, and these effects could be corrected for (the extracted soluble organics could also be used for isotopic analysis). The extraction time for a routine eight-sample subset was reduced from 4 h (cryogenic distillation) to 45 min, limited only by the size of the centrifuge(s) used. This method provides a rapid, low-cost and reliable alternative to conventional vacuum and other distillation methods that can alleviate current restrictions on ecosystem- and global-scale studies that require high-throughput leaf water isotopic analysis. Copyright (c) 2008 John Wiley & Sons, Ltd.     

Continuous analysis of δ18O and δD values of water by diffusion sampling cavity ring‐down spectrometry: a novel sampling device for unattended field monitoring of precipitation,ground and surface waters

A novel sampling device suitable for continuous, unattended field monitoring of rapid isotopic changes in environmental waters is described. The device utilises diffusion through porous PTFE tubing to deliver water vapour continuously from a liquid water source for analysis of δ¹⁸O and δD values by Cavity Ring‐Down Spectrometry (CRDS). Separation of the analysed water vapour from non‐volatile dissolved and particulate contaminants in the liquid sample minimises spectral interferences associated with CRDS analyses of many aqueous samples. Comparison of isotopic data for a range of water samples analysed by Diffusion Sampling‐CRDS (DS‐CRDS) and Isotope Ratio Mass Spectrometry (IRMS) shows significant linear correlations between the two methods allowing for accurate standardisation of DS‐CRDS data. The internal precision for an integration period of 3 min (standard deviation (SD) = 0.1 ‰ and 0.3 ‰ for δ¹⁸O and δD values, respectively) is similar to analysis of water by CRDS using an autosampler to inject and evaporate discrete water samples. The isotopic effects of variable air temperature, water vapour concentration, water pumping rate and dissolved organic content were found to be either negligible or correctable by analysis of water standards. The DS‐CRDS system was used to analyse the O and H isotope composition in short‐lived rain events. Other applications where finely time resolved water isotope data may be of benefit include recharge/discharge in groundwater/river systems and infiltration‐related changes in cave drip water. Copyright © 2011 John Wiley & Sons, Ltd.     

Determination of the stable carbon isotopic compositions of 2‐methyltetrols in ambient aerosols from the Changbai Mountains

Isoprene is one of the most important non‐methane hydrocarbons (NMHCs) in the troposphere: it is a significant precursor of O₃ and it affects the oxidative state of the atmosphere. The diastereoisomeric 2‐methyltetrols, 2‐methylthreitol and 2‐methylerythritol, are marker compounds of the photooxidation products of atmospheric isoprene. In order to obtain valuable information on the δ¹³C value of isoprene in the atmosphere, the stable carbon isotopic compositions of the 2‐methyltetrols in ambient aerosols were investigated. The 2‐methyltetrols were extracted from filter samples and derivatized with methylboronic acid, and the δ¹³C values of the methylboronate derivatives were determined by gas chromatography/combustion/isotope ratio mass spectrometry (GC/C/IRMS). The δ¹³C values of the 2‐methyltetrols were then calculated through a simple mass balance equation between the 2‐methyltetrols, methylboronic acid and the methylboronates. The δ¹³C values of the 2‐methyltetrols in aerosol samples collected at the Changbai Mountain Nature Reserves in eastern China were found to be ?24.66 ± 0.90‰ and ?24.53 ± 1.08‰ for 2‐methylerythritol and 2‐methylthreitol, respectively. Based on the measured isotopic composition of the 2‐methyltetrols, the average δ¹³C value of atmospheric isoprene is inferred to be close to or slightly heavier than ?24.66‰ at the collection site during the sampling period. Copyright © 2010 John Wiley & Sons, Ltd.     

Concentration effects on laser-based δ18 O and δ2 H measurements and implications for the calibration of vapour measurements with liquid standards

Recently available isotope ratio infrared spectroscopy can directly measure the isotopic composition of atmospheric water vapour (δ¹⁸O, δ²H), overcoming one of the main limitations of isotope ratio mass spectrometry (IRMS) methods. Calibrating these gas‐phase instruments requires the vapourisation of liquid standards since primary standards in principle are liquids. Here we test the viability of calibrating a wavelength‐scanned cavity ring‐down spectroscopy (CRDS) instrument with vapourised liquid standards. We also quantify the dependency of the measured isotope values on the water concentration for a range of isotopic compositions. In both liquid and vapour samples, we found an increase in δ¹⁸O and δ²H with water vapour concentration. For δ¹⁸O, the slope of this increase was similar for liquid and vapour, with a slight positive relationship with sample δ‐value. For δ²H, we found diverging patterns for liquid and vapour samples, with no dependence on δ‐value for vapour, but a decreasing slope for liquid samples. We also quantified tubing memory effects to step changes in isotopic composition, avoiding concurrent changes in the water vapour concentration. Dekabon tubing exhibited much stronger, concentration‐dependent, memory effects for δ²H than stainless steel or perfluoroalkoxy (PFA) tubing. Direct vapour measurements with CRDS in a controlled experimental chamber agreed well with results obtained from vapour simultaneously collected in cold traps analysed by CRDS and IRMS. We conclude that vapour measurements can be calibrated reliably with liquid standards. We demonstrate how to take the concentration dependencies of the δ‐values into account. Copyright © 2010 John Wiley & Sons, Ltd.     

Multidimensional HRGC for sample components with a wide range of volatilities and polarities

A diverse mixture of volatile headspace analytes containing compounds with boiling points covering a range from ?196°c to 145°c can be separated in approximately 40 minutes by multidimensional HRGC. The described provisional MD-HRGC Systems employ cryogenic sample collection, four 0.53 mm FSOT columns, and multi-ramp temperature programming of either one or two ovens. Enhanced sensitivity for organic species and minimal interference from water vapour in the samples can be obtained by a MD-HRGC configuration that uses separate ovens, appropriate column switching operations, and TCD + FID detection.     

Reliable determination of oxygen and hydrogen isotope ratios in atmospheric water vapour adsorbed on 3A molecular sieve

The isotope ratio of atmospheric water vapour is determined by wide-ranging feedback effects from the isotope ratio of water in biological water pools, soil surface horizons, open water bodies and precipitation. Accurate determination of atmospheric water vapour isotope ratios is important for a broad range of research areas from leaf-scale to global-scale isotope studies. In spite of the importance of stable isotopic measurements of atmospheric water vapour, there is a paucity of published data available, largely because of the requirement for liquid nitrogen or dry ice for quantitative trapping of water vapour. We report results from a non-cryogenic method for quantitatively trapping atmospheric water vapour using 3A molecular sieve, although water is removed from the column using standard cryogenic methods. The molecular sieve column was conditioned with water of a known isotope ratio to 'set' the background signature of the molecular sieve. Two separate prototypes were developed, one for large collection volumes (3 mL) and one for small collection volumes (90 microL). Atmospheric water vapour was adsorbed to the column by pulling air through the column for several days to reach the desired final volume. Water was recovered from the column by baking at 250 degrees C in a dry helium or nitrogen air stream and cryogenically trapped. For the large-volume apparatus, the recovered water differed from water that was simultaneously trapped by liquid nitrogen (the experimental control) by 2.6 per thousand with a standard deviation (SD) of 1.5 per thousand for delta(2)H and by 0.3 per thousand with a SD of 0.2 per thousand for delta(18)O. Water-vapour recovery was not satisfactory for the small volume apparatus.     

On the calibration of continuous,high‐precision δ18O and δ2H measurements using an off‐axis integrated cavity output spectrometer

The ¹⁸O and ²H of water vapor serve as powerful tracers of hydrological processes. The typical method for determining water vapor δ¹⁸O and δ²H involves cryogenic trapping and isotope ratio mass spectrometry. Even with recent technical advances, these methods cannot resolve vapor composition at high temporal resolutions. In recent years, a few groups have developed continuous laser absorption spectroscopy (LAS) approaches for measuring δ¹⁸O and δ²H which achieve accuracy levels similar to those of lab‐based mass spectrometry methods. Unfortunately, most LAS systems need cryogenic cooling and constant calibration to a reference gas, and have substantial power requirements, making them unsuitable for long‐term field deployment at remote field sites. A new method called Off‐Axis Integrated Cavity Output Spectroscopy (OA‐ICOS) has been developed which requires extremely low‐energy consumption and neither reference gas nor cryogenic cooling. In this report, we develop a relatively simple pumping system coupled to a dew point generator to calibrate an ICOS‐based instrument (Los Gatos Research Water Vapor Isotope Analyzer (WVIA) DLT‐100) under various pressures using liquid water with known isotopic signatures. Results show that the WVIA can be successfully calibrated using this customized system for different pressure settings, which ensure that this instrument can be combined with other gas‐sampling systems. The precisions of this instrument and the associated calibration method can reach ～0.08‰ for δ¹⁸O and ～0.4‰ for δ²H. Compared with conventional mass spectrometry and other LAS‐based methods, the OA‐ICOS technique provides a promising alternative tool for continuous water vapor isotopic measurements in field deployments. Copyright © 2009 John Wiley & Sons, Ltd.     

Monitoring of carcinogenic PAHs in air under mild–warm ambient temperatures: relative importance of vapour- and particulate-phase analyses in assessing exposure and risk

Atmospheric polycyclic aromatic hydrocarbons (PAHs) are often determined by collecting only the particulate phase. The aim of this study was to ascertain in the field to what extent not collecting the vapour phase may affect the exposure assessment and the risk assessment for carcinogenic PAHs, under ambient temperatures typical of Southern Europe. PM₁₀ 24-h samples were collected in Rome every two months throughout one year on a filter backed by two polyurethane foam sections. Daily mean temperatures during sampling reached 31°C, with hourly maximum values up to 36°C. While four-ring PAHs were found in the vapour phase to a large extent, the calculated annual means of five-ring PAHs, including benzo[a]pyrene, were not affected significantly by the amounts collected as vapour phase. By using the “toxicity equivalence factor” approach, the carcinogenic risk overall attributable to particle-bound PAHs accounted for at least 97% of the risk attributable to total (particulate + vapour phase) PAHs.     

Summary of ISO/TC 201 Standard: XIX ISO 17331:2004—Surface chemical analysis—Chemical methods for the collection of elements from the surface of silicon‐wafer working reference materials and their determination by total‐reflection x‐ray fluorescence (TXRF) spectroscopy

This international standard specifies chemical methods for the collection of iron and/or nickel from the surface of silicon‐wafer working reference materials by the vapour‐phase decomposition method or the direct acid droplet decomposition method. The determination of the elements collected may be carried out by total‐reflection x‐ray fluorescence spectroscopy, as well as by graphite‐furnace atomic absorption spectroscopy or inductively coupled plasma mass spectroscopy. This international standard applies to iron and/or nickel atomic surface densities from 6 × 10⁹ to 5 × 10¹¹ atoms cm^?2. Copyright © 2005 John Wiley & Sons, Ltd.     

Novel silver‐tubing method for quantitative introduction of water into high‐temperature conversion systems for stable hydrogen and oxygen isotopic measurements

A new method to seal water in silver tubes for use in a TC/EA (thermal conversion/elemental analyzer) reduction unit using a semi‐automated sealing apparatus can yield reproducibilities (1 standard deviation) of δ²H and δ¹⁸O measurements of 1.0‰ and 0.06‰, respectively. These silver tubes containing reference waters may be preferred for the calibration of H‐ and O‐bearing materials analyzed with a TC/EA reduction unit. The new sealing apparatus employs a computer‐controlled stepping motor to produce silver tubes identical in length. The reproducibility of the mass of water sealed in tubes (in a range of 200–400 µg) can be as good as 1%. Approximately 99% of the sealed silver tubes are satisfactory (leak free). Although silver tubes sealed with reference waters are robust and can be shaken or heated to 110°C with no loss of integrity, they should not be frozen because the expansion during the phase transition of water to ice will break the cold seals and all the water will be lost. The tubes should be shipped in insulated containers. This new method eliminates air inclusions and isotopic fractionation of water associated with the loading of water into capsules using a syringe. The method is also more than an order of magnitude faster than preparing water samples in ordinary Ag capsules. Nevertheless, some laboratories may prefer loading water into silver capsules because expensive equipment is not needed, but users of this method are cautioned to apply the necessary corrections for evaporation, back exchange with laboratory atmospheric moisture, and blanks. Copyright © 2010 John Wiley & Sons, Ltd.     

Noria: A Highly Xe‐Selective Nanoporous Organic Solid

Separation of xenon and krypton is of industrial and environmental concern; the existing technologies use cryogenic distillation. Thus, a cost‐effective, alternative technology for the separation of Xe and Kr and their capture from air is of significant importance. Herein, we report the selective Xe uptake in a crystalline porous organic oligomeric molecule, noria, and its structural analogue, PgC‐noria, under ambient conditions. The selectivity of noria towards Xe arises from its tailored pore size and small cavities, which allows a directed non‐bonding interaction of Xe atoms with a large number of carbon atoms of the noria molecular wheel in a confined space.     

Membrane permeation continuous‐flow isotope ratio mass spectrometry for on‐line carbon isotope ratio determination

Gaseous membrane permeation (MP) technologies have been combined with continuous‐flow isotope ratio mass spectrometry for on‐line δ¹³C measurements. The experimental setup of membrane permeation‐gas chromatography/combustion/isotope ratio mass spectrometry (MP‐GC/C/IRMS) quantitatively traps gas streams in membrane permeation experiments under steady‐state conditions and performs on‐line gas transfer into a GC/C/IRMS system. A commercial polydimethylsiloxane (PDMS) membrane sheet was used for the experiments. Laboratory tests using CO₂ demonstrate that the whole process does not fractionate the C isotopes of CO₂. Moreover, the δ¹³C values of CO₂ permeated on‐line give the same isotopic results as off‐line static dual‐inlet IRMS δ¹³C measurements. Formaldehyde generated from aqueous formaldehyde solutions has also been used as the feed gas for permeation experiments and on‐line δ¹³C determination. The feed‐formaldehyde δ¹³C value was pre‐determined by sampling the headspace of the thermostated aqueous formaldehyde solution. Comparison of the results obtained by headspace with those from direct aqueous formaldehyde injection confirms that the headspace sampling does not generate isotopic fractionation, but the permeated formaldehyde analyzed on‐line yields a ¹³C enrichment relative to the feed δ¹³C value, the isotopic fractionation being 1.0026 ± 0.0003. The δ¹³C values have been normalized using an adapted two‐point isotopic calibration for δ¹³C values ranging from ?42 to ?10‰. The MP‐GC/C/IRMS system allows the δ¹³C determination of formaldehyde without chemical derivatization or additional analytical imprecision. Copyright © 2009 John Wiley & Sons, Ltd.     

Trace Impurity Removal from Air

In addition to Nitrogen, Oxygen and Argon, ambient air contains many trace impurities. These impurities include moisture, Carbon Dioxide, Oxides of Nitrogen and light Hydrocarbons. Prior to cryogenic distillation of air to produce Nitrogen, Oxygen and Argon these trace impurities have to be removed since, some of these constitute a safety hazard in the cryogenic plant. A significant amount of information is available in the literature for the removal of Water and Carbon Dioxide from air. However, only limited information is available for the removal of other trace impurities. We discuss the results of an experimental study on the removal of these trace impurities from air.These days, air pre purification is carried out primarily by adsorption based technologies. There are two main choices: Thermal Swing Adsorption (TSA) processes, and Pressure Swing Adsorption (PSA) processes. Main differences between these two approaches and the trace impurity removal results are discussed.     

Xenon Recovery by DD3R Zeolite Membranes: Application in Anaesthetics

Xe is only produced by cryogenic distillation of air, and its availability is limited by the extremely low abundance. Therefore, Xe recovery after usage is the only way to guarantee sufficient supply and broad application. Herein we demonstrate DD3R zeolite as a benchmark membrane material for CO₂/Xe separation. The CO₂ permeance after an optimized membrane synthesis is one order magnitude higher than for conventional membranes and is less susceptible to water vapour. The overall membrane performance is dominated by diffusivity selectivity of CO₂ over Xe in DD3R zeolite membranes, whereby rigidity of the zeolite structure plays a key role. For relevant anaesthetic composition (<5 % CO₂) and condition (humid), CO₂ permeance and CO₂/Xe selectivity stabilized at 2.0×10^?8 mol m^?2 s^?1 Pa^?1 and 67, respectively, during long‐term operation (>320 h). This endows DD3R zeolite membranes great potential for on‐stream CO₂ removal from the Xe‐based closed‐circuit anesthesia system. The large cost reduction of up to 4 orders of magnitude by membrane Xe‐recycling (>99+%) allows the use of the precious Xe as anaesthetics gas a viable general option in surgery.     

Thermodynamics and vacuum distillation studies of liquid Al–Ga and In–Sn alloys

Activities of components in liquid Al–Ga and In–Sn alloys, the separation coefficients and vapour–liquid phase equilibrium in vacuum distillation were predicted using the molecular interaction volume model as a function of the activity coefficients. The results indicated that both Al and In are preferentially volatilised into vapour phase while Ga and Sn remain in residue. Similarly, we found that both the mass fraction and the content of Al and In in vapour phase increase as distillation temperature increases such that when the content of Al is 0.005985 wt% and In is 0.004141 wt% in vapour phase, respectively, in liquid phase, it was 70 wt% at T = 1073 K for both. The calculated values of activity and activity coefficients at various temperatures are presented. Comparison of the predicted values with experimental data indicates good agreement, thus verifying from statistical thermodynamics viewpoint that the model is stable and reliable.     

Polydimethylsiloxane‐coated partitioning sample collection device for the precise quantification of polycyclic aromatic hydrocarbons in air

A novel partitioning collection device comprising a glass cartridge packed with poly(dimethylsiloxane)‐coated macroporous silica particles was developed for the precise quantification of polycyclic aromatic hydrocarbons in air. The analyte collection and elution performances achieved using different amounts of poly(dimethylsiloxane) coating were quantitatively evaluated. The sample retention power increased with increasing the coating, and more than 250 L of air could be collected without analyte breakthrough at a sampling temperature of 35°C. During the air collection, the moisture in the air was not retained on the particles due to the hydrophobic surface of the sorbent. A complete and rapid elution of the collected analytes from the device was accomplished by the passage of only 10 mL of acetone with ultrasonication for 1 min. The proposed method was successfully applied for the determination of airborne polycyclic aromatic hydrocarbons in tunnel air.     

Conversion de UF6 appauvri en U3O8

Uranium hexafluoride (UF₆), to or from isotopic enrichment plants is stored and transported, as a solid, in tanks containing 2 to 12 metric tons of material. Sampling must be carry out after complete melting obtained by heating of the tank. This sampling process is difficult and hazardous by risks of local solidification (sealing), of reaction with air moisture (Fluorhydric Acid, highly corrosive and toxic is formed), of chemical and radioactive contamination (in case of leaking), of loss of expensive material (especialy if enriched UF₆), and of over-filling of sampling pot (possible domage during warming up of itagain).The described new device was concepted and developed by COGEMA Laboratories and is used for two years in sampling facilities of enrichment plant of PIERRELATTE. It permits to warrant sample validity and eliminate all the hereabove risks.It allows seeing and adjusting volume of the samples and their flow, and permits measurement of temperature and pressure, specified for UF₆.This new device is usable for many others materials which present some risks and difficults, as Fluorine and its derivates, chlorine, liquefied inflammable gases etc.     

Thermogravimetric analysis for boiling points and vapour pressure

A TGA instrument has been adapted for rapid measurement of boiling points and vapour pressure at temperatures from ambient up to 400°C and pressures from ambient down to 20 mm Hg. Samples were contained in sealed holders having a laser-drilled aperture. Several organic liquids in the 100 to 300 gMW range showed good agreement with reference vapour pressure data. Sample mass, heating rate, and use of inert diluents were important variables affecting accuracy of vapour pressure measurements.     

Doubly labeled water analysis using cavity ring-down spectroscopy

The doubly labeled water method provides an objective and accurate measure of total energy expenditure in free‐living subjects and is considered the gold‐standard method for this measurement. Its use, however, is limited by the need to employ isotope ratio mass spectrometry (IRMS) to obtain the high‐precision isotopic abundance analyses needed to optimize the dose of expensive ¹⁸O‐labeled water. Recently, cavity‐ring down spectroscopy (CRDS) instruments have become commercially available and may serve as a less expensive alternative to IRMS. We compared the precision and accuracy of CRDS with those of IRMS for the measurement of total energy expenditure from urine specimens in 14 human subjects. The relative accuracy and precision (SD) for total body water was 0.5 ± 1% and for total energy expenditure was 0.5 ± 6%. The CRDS instrument displayed a memory between successive specimens of 5% for ¹⁸O and 9% for ²H. The memory necessitated carefully ordering of specimens to reduce isotopic disparity, performance of several injections of each specimen to condition the analyzer, and use of a mathematical memory correction on subsequent injections. These limited the specimen throughput to about one urine specimen per hour. CRDS provided accuracy and precision for isotope abundance measurements of urine that were comparable with those of IRMS. The memory problems were easily recognized by our experienced laboratory staff, but future efforts should be aimed at reducing the memory of the CRDS so that it would be less likely to result in poor reproducibility in laboratories using doubly labeled water for the first time. Copyright © 2010 John Wiley & Sons, Ltd.     

Protein analysis by desorption electrospray ionization mass spectrometry and related methods

Desorption electrospray ionization mass spectrometry (DESI‐MS) requires little to no sample preparation and has been successfully applied to the study of biologically significant macromolecules such as proteins. However, DESI‐MS and other ambient methods that use spray desorption to process samples during ionization appear limited to smaller proteins with molecular masses of 25 kDa or less, and a decreasing instrumental response with increasing protein size has often been reported. It has been proposed that this limit results from the inability of some proteins to easily desorb from the surface during DESI sampling. The present study investigates the apparent mass dependence of the instrumental response observed during the DESI‐MS analysis of proteins using spray desorption collection and reflective electrospray ionization. Proteins, as large as 66 kDa, are shown to be quantitatively removed from surfaces by using spray desorption collection. However, incomplete dissolution and the formation of protein–protein and protein–contaminant clusters appear to be responsible for the mass‐dependent loss in sensitivity for protein analysis. Alternative ambient mass spectrometry approaches that address some of the problems encountered by spray desorption techniques for protein analysis are also discussed. Copyright © 2013 John Wiley & Sons, Ltd.