Ultrasound‐assisted temperature‐controlled ionic liquid emulsification microextraction coupled with capillary electrophoresis for the determination of parabens in personal care products

We developed a CE and ultrasound‐assisted temperature‐controlled ionic liquid emulsification microextraction method for the determination of four parabens (methyl paraben, ethyl paraben, propyl paraben, and butyl paraben) in personal care products including mouthwash and toning lotion. In the proposed extraction procedure, ionic liquid (IL, 1‐octyl‐3‐methylimidazolium hexafluorophosphate) was used as extraction solvent, moreover, no disperser solvent was needed. Parameters affecting the extraction efficiency including volume of IL, heating temperature, ultrasonic time, extraction time, sample pH, ionic strength, and centrifugation time were optimized. Under the optimized conditions, the method was found to be linear over the range of 3–500 ng/mL with coefficient of determination (R²) in the range of 0.9990–0.9998. The LODs and LOQs for the four parabens were 0.45–0.72 ng/mL and 1.50–2.40 ng/mL, respectively. Intraday and interday precisions (RSDs, n = 5) were in the range of 5.4–6.8% and 7.0–8.7%, respectively. The recoveries of parabens at different spiked levels ranged from 71.9 to 119.2% with RSDs less than 9.5%.     

Extraction of major alkaloids from poppy straw with near-critical mixtures of carbon dioxide and polar modifiers

Near-critical extraction of major alkaloids from poppy straw was performed successfully with a simple device consisting mainly of two chromatographic pumps and a pressure regulator. The optimum extractant, consisting of carbon dioxide, methanol and water, gave a quantitative extraction of thebaine, codeine and morphine in 20 min. The method was compared with a classical liquid-solid extraction procedure and carbon dioxide was shown to act as a transporting agent of the extraction solvent (methanol-water) into the vegetable matrix.     

Developing a miniaturized setup for in‐tube simultaneous determination of three alkaloids using electromembrane extraction in combination with ultraviolet spectrophotometry

Herein, electromembrane extraction was combined with ultraviolet spectrophotometry using a customized manifold for preconcentration and simultaneous determination of morphine, codeine, and papaverine in water and human urine samples. Absorption spectra of the extracts were recorded inside the lumen of the hollow fiber using two fiber optics connected to a miniature spectrophotometer. Partial least squares regression was applied to resolve the overlapped spectra of the analytes. Performance of the model was validated by an independent test set. Central composite design was applied to optimize the extraction parameters. The optimized extraction conditions are as follows; supporting liquid membrane: 2‐nitrophenyl octyl ether containing 15% v/v bis(2‐ethylhexyl) phosphate, applied voltage: 80 V, donor pH: 3.0, acceptor pH: 1.0, extraction time: 20 min. Finally, the optimized extraction method was validated for determination of the mentioned alkaloids in human urine samples. The method showed good linearity (R² > 0.995) for all of the mentioned alkaloids. The limits of detection for morphine, codeine, and papaverine in diluted human urine were found to be 0.6, 1.1, and 0.6 ng/mL, respectively with acceptable relative standard deviations. Enrichment factors of 104, 108, and 102 were achieved for morphine, codeine, and papaverine, respectively.     

Rapid and cost‐effective method for the simultaneous quantification of seven alkaloids in Corydalis decumbens by microwave‐assisted extraction and capillary electrophoresis

A rapid and cost‐effective method based on microwave‐assisted extraction followed by capillary electrophoresis was developed for simultaneous quantification of seven alkaloids in Corydalis decumbens for the first time. The main parameters affecting microwave‐assisted extraction and capillary electrophoresis separation were investigated and optimized. The optimal microwave‐assisted extraction was performed at 40°C for 5 min using methanol/water (90:10, v/v) as the extracting solvent. Electrophoretic separation was achieved within 15 min using an uncoated fused‐silica capillary (50 μm internal diameter and 27.7 cm effective length) and a 500 mM Tris buffer containing 45% v/v methanol (titrated to pH^* 2.86 with H₃PO₄). The developed method was successfully applied to the quantification of seven alkaloids in Corydalis decumbens obtained from different regions of China. The combination of microwave‐assisted extraction with capillary electrophoresis was an effective method for the rapid analysis of the alkaloids in Corydalis decumbens .     

Ionic liquid‐based ultrasound‐assisted extraction of fangchinoline and tetrandrine from Stephaniae tetrandrae

An ionic liquid‐based ultrasound‐assisted extraction method has been developed for the effective extraction of fangchinoline and tetrandrine from Stephaniae tetrandrae. The effects of some ultrasound‐assisted extraction parameters including the concentration of [BMIM][BF₄], pH, ultrasonic power and time were investigated to optimize the ultrasound‐assisted extraction conditions. Compared to the regular ultrasound‐assisted extraction and traditional refluent extraction, the proposed [BMIM][BF₄]‐based ultrasound‐assisted extraction offered shorter extraction times (from 6 h to 40 min) and remarkable higher efficiencies (approximately 30% improved), which supported the suitability of the proposed approach. In addition, the proposed approach was confirmed by the good correlation coefficient (R²), recovery and reproducibility (RSD, n = 5), which were in the range of 0.9992–0.9995, 85.5–101.1%, and 1.87–4.33%, respectively.     

Ultrasound‐assisted supramolecular‐solvent‐based microextraction combined with high‐performance liquid chromatography for the analysis of chlorophenols in environmental water samples

An efficient, inexpensive and environmentally benign ultrasound‐assisted supramolecular‐solvent‐based microextraction technique combined with high‐performance liquid chromatography was used for the determination of chlorophenols in environmental water samples. Different factors such as amount of decanoic acid, volume of tetrahydrofuran, pH of the sample, ultrasound time and ionic strength were investigated and optimized. The optimized extraction conditions were 60 mg decanoic acid, 1.5 mL tetrahydrofuran, 3 min ultrasound time, without salt addition. Under this condition, the extraction recoveries were 83.0–89.3 with preconcentration factors of 94–102. The calibration curves were linear from 5.0–400.0 ng/mL with square of the correlation coefficient higher than 0.9998 and the limits of detection were between 1.5–2.0 ng/mL. The values of intra‐ and inter‐day relative standard deviations were 3.2–6.0 and 7.3–8.0%, respectively. Analysis of different samples showed that the concentration of 2,5‐dichlorophenol in Babolrood river water was 80.6 ng/mL.     

Application of capillary zone electrophoresis in the separation and determination of the principal gum opium alkaloids

We describe the use of capillary zone electrophoresis (CZE) for the qualitative and quantitative determination of major alkaloids (i.e., thebaine, codeine, morphine, papavarine and narcotine) in gum opium involving the analysis of alkaloids without derivatization or purification. Three extractions with 2.5% w/v aqueous acetic acid quantitatively extracted major alkaloids. The separation was carried out by CZE using a 7:3 mixture of methanol and sodium acetate (100 mM, pH 3.1) at a potential of 15 kV, with UV detection at 224 nm. Spiking of pure reference alkaloid standards in the opium extract was used for peak identification. The influences of buffer composition, pH and voltage on the separation of alkaloids were studied. The detection limit of each alkaloid dissolved in methanol was found to be 850 ng/mL (morphine), 450 ng/mL (thebaine), 500 ng/mL (codeine), 550 ng/mL (papaverine), and 500 ng/mL (narcotine) at an injection pressure of 300 mbar (injection volume, 4 nL) with a signal-to-noise ratio of 3:1. The external standard method was used for the quantification of alkaloids. The calibration plot was based on linear regression analysis. The relative standard deviation (RSD) for peak area and migration time was in the range of 1.03-3.56% and 0.34-0.69%, respectively. Percentage compositions (g%) of opium alkaloids in five gum opium samples were found to be in the range of 14.45-15.95 (morphine), 2.0-3.45 (codeine), 1.32-2.73 (thebaine), 0.92-2.37 (papavarine), and 3.85-5.77 (narcotine). The method developed is suitable for the routine analysis of major gum opium alkaloids in samples of forensic importance.     

Hydrophobic ionic liquid‐based ultrasound‐assisted extraction of magnolol and honokiol from cortex Magnoliae officinalis

The hydrophobic ionic liquid of [BMIM][PF₆] was successfully used for the ultrasound‐assisted extraction of hydrophobic magnolol and honokiol from cortex Magnoliae officinalis. To obtain the best extraction efficiencies, some ultrasonic parameters including the concentration of [BMIM][PF₆], pH, ultrasonic power and ultrasonic time were evaluated. The results obtained indicated that the [BMIM][PF₆]‐based ultrasound‐assisted extraction efficiencies of magnolol and honokiol were greater than those of the [BMIM][BF₄]‐based ultrasound‐assisted extraction (from 48.6 to 45.9%) and the traditional ethanol reflux extraction (from 16.2 to 13.3%). Furthermore, the proposed extraction method is validated by the recovery, correlation coefficient (R²) and reproducibility (RSD, n=5), which were 90.8–102.6, 0.9992–0.9998, and 1.6–5.4%, respectively.     

Ionic‐liquid‐based ultrasound/microwave‐assisted extraction of 2,4‐dihydroxy‐7‐methoxy‐1,4‐benzoxazin‐3‐one and 6‐methoxy‐benzoxazolin‐2‐one from maize (Zea mays L.) seedlings

We evaluated an ionic‐liquid‐based ultrasound/microwave‐assisted extraction method for the extraction of 2,4‐dihydroxy‐7‐methoxy‐1,4‐benzoxazin‐3‐one and 6‐methoxy‐benzoxazolin‐2‐one from etiolated maize seedlings. We performed single‐factor and central composite rotatable design experiments to optimize the most important parameters influencing this technique. The best results were obtained using 1.00 M 1‐octyl‐3‐methylimidazolium bromide as the extraction solvent, a 50°C extraction temperature, a 20:1 liquid/solid ratio (mL/g), a 21 min treatment time, 590 W microwave power, and 50 W fixed ultrasonic power. We performed a comparison between ionic‐liquid‐based ultrasound/microwave‐assisted extraction and conventional homogenized extraction. Extraction yields of 2,4‐dihydroxy‐7‐methoxy‐1,4‐benzoxazin‐3‐one and 6‐methoxy‐benzoxazolin‐2‐one by the ionic‐liquid‐based ultrasound/microwave‐assisted extraction method were 1.392 ± 0.051 and 0.205 ± 0.008 mg/g, respectively, which were correspondingly 1.46‐ and 1.32‐fold higher than those obtained by conventional homogenized extraction. All the results show that the ionic‐liquid‐based ultrasound/microwave‐assisted extraction method is therefore an efficient and credible method for the extraction of 2,4‐dihydroxy‐7‐methoxy‐1,4‐benzoxazin‐3‐one and 6‐methoxy‐benzoxazolin‐2‐one from maize seedlings.     

Dispersive Micro Solid‐phase Extraction Coupled with Ultrasound‐assisted Solvent Desorption for Determination of Synthetic Polycyclic and Nitro‐aromatic Musks in Aqueous Samples

An optimized method for the determination of five synthetic polycyclic: celestolide (ADBI), phantolide (AHMI), traseolide (ATII), galaxolide (HHCB), tonalide (AHTN), and two nitro‐aromatic musks: musk xylene (MX) and musk ketone (MK), in water samples is described. The method involves a dispersive micro solid‐phase extraction (D‐μ‐SPE) plus ultrasound‐assisted solvent desorption (UASD) prior to their determination by gas chromatography‐mass spectrometry (GC‐MS) using the selected ion storage (SIS) mode. Factors affecting the extraction efficiency of the target analytes from water samples and ultrasound‐assisted solvent desorption were optimized by a Box‐Behnken design method. The optimal extraction conditions involved immersing 10.1 mg of a typical octadecyl (C18) bonded silica adsorbent (i.e., ENVI‐18) in a 50 mL water sample. After 10.4 min of extraction by vigorously shaking, the adsorbent was collected and dried on a filter, and the target musks were desorbed by ultrasound‐assisted for 38 sec with n‐hexane (200 μL) as the desorption solvent. A 10 μL aliquot was then directly determined by large‐volume injection GC‐MS. The limits of quantitation (LOQs) were 1.2 to 5 ng/L. The precision for these analytes, as indicated by relative standard deviations (RSDs), were less than 11% for both intra‐ and inter‐day analysis. Accuracy, expressed as the mean extraction recovery, was between 74% and 92%. A preliminary analysis of the effluents from municipal wastewater treatment plants (MWTP) and river water samples revealed that HHCB and AHTN were the two most commonly detected synthetic musks; their concentration were determined to range from 88 to 690 ng/L for effluent samples, and 5 to 320 ng/L for river water samples. This is a simple, low cost, effective, and eco‐friendly analytical method.     

Ionic‐liquid‐based,manual‐shaking‐ and ultrasound‐assisted,surfactant‐enhanced emulsification microextraction for the determination of three fungicide residues in juice samples

A novel manual‐shaking‐ and ultrasound‐assisted surfactant‐enhanced emulsification microextraction method was developed for the determination of three fungicides in juice samples. In this method, the ionic liquid, 1‐ethyl‐3‐methylimidazolium bis[(trifluoromethyl)sulfonyl]imide, instead of a volatile organic solvent was used as the extraction solvent. The surfactant, NP‐10, was used as an emulsifier to enhance the dispersion of the water‐immiscible ionic liquid into an aqueous phase, which accelerated the mass transfer of the analytes. Organic dispersive solvent typically required in common dispersive liquid–liquid microextraction methods was not necessary. In addition, manual shaking for 15 s before ultrasound to preliminarily mix the extraction solvent and the aqueous sample could greatly shorten the time for dispersing the ionic liquid into aqueous solution by ultrasound irradiation. Several experimental parameters affecting the extraction efficiency, including type and volume of extraction solvent, type and concentration of surfactant, extraction time, and pH, were optimized. Under the optimized conditions, good linearity with the correlation coefficients (γ) higher than 0.9986 and high sensitivity with the limit of detection ranging from 0.4 to 1.6 μg/L were obtained. The average recoveries ranged from 61.4 to 86.0% for spiked juice, with relative standard deviations from 1.8 to 9.7%. The proposed method was demonstrated to be a simple, fast, and efficient method for the analysis of the target fungicides in juice samples.     

A rapid and reliable solid-phase extraction method for high-performance liquid chromatographic analysis of opium alkaloids from papaver plants

A rapid and reliable solid-phase extraction method for HPLC analysis of opium alkaloids from Papaver plants was established. Fifty mg of dried and powdered plant sample was extracted with 5 ml of 5% acetic acid for 30 min under sonication. After centrifugation, 3 ml of the supernatant was loaded on a reversed-phase cation-exchange solid-phase extraction cartridge. After seriate washings with 0.1 M hydrochloric acid and methanol, alkaloids were eluted with a mixture of 28% ammonia and methanol (1:19). The eluate was concentrated under nitrogen stream at 40 degrees C and the residue was dissolved in 50% aqueous methanol for high performance liquid chromatographic analysis. With this solid-phase extraction method, the recovery of morphine, codeine, oripavine, thebaine, papaverine, noscapine and sanguinarine was from 99.94 to 112.18% when the standard alkaloids were added to the plant samples. Opium alkaloids of a variety of genus Papaver plants cultivated in a field and phytotron were analyzed by this method.     

Comparison of two ultrasound‐enhanced microextractions combined with HPLC for determining acaricides in water

An ultrasound‐enhanced in situ solvent formation microextraction has been developed first time and compared with ultrasound‐enhanced ionic‐liquid‐assisted dispersive liquid–liquid microextraction for the HPLC analysis of acaricides in environmental water samples. A ionic liquid ([C₈MIM][PF₆]) was used as the green extraction solvent through two pathways. The experimental parameters, such as the type and volume of both of the extraction solvent disperser solvent, ultrasonication time, and salt addition, were investigated and optimized. The analytical performance using the optimized conditions proved the feasibility of the developed methods for the quantitation of trace levels of acaricides by obtaining limits of detection that range from 0.54 to 3.68 μg/L. The in situ solvent formation microextraction method possesses more positive characteristics than the ionic‐liquid‐assisted dispersive liquid–liquid microextraction method (except for spirodiclofen determination) when comparing the validation parameters. Both methods were successfully applied to determining acaricides in real water samples.     

Ultrasound‐assisted dispersive liquid–liquid microextraction coupled with capillary gas chromatography for simultaneous analysis of nine pyrethroids in domestic wastewaters

A simple and rapid ultrasound‐assisted dispersive liquid–liquid microextraction method coupled with GC‐flame ionization detection was developed for simultaneous determination of nine pyrethroids in domestic wastewater samples. An ultrasound‐assisted process was applied to accelerate the formation of the fine cloudy solution using small volume of disperser solvent, which markedly increased the extraction efficiency and reduced the equilibrium time. Various parameters affecting the extraction efficiency were investigated, including the type and volume of extraction solvent and disperser solvent, extraction and ultrasonic time. Good linearity was obtained for all analytes in the range of 0.8–100 μg/L with the correlation coefficient (r²)≥0.998. The recoveries at three spiking levels ranged from 75.3 to 101.2% with the RSD less than 8.7% (n=5). Under the optimum condition, the enrichment factors for the nine pyrethroids ranged from 728‐ to 1725‐fold. This method offered a good alternative for routine analysis due to its simplicity and reliability.     

Monitoring the oleuropein content of olive leaves and fruits using ultrasound‐ and salt‐assisted liquid–liquid extraction optimized by response surface methodology and high‐performance liquid chromatography

A novel and rapid ultrasound‐ and salt‐assisted liquid–liquid extraction coupled with high‐performance liquid chromatography has been optimized by response surface methodology for the determination of oleuropein from olive leaves. Box–Behnken design was used for optimizing the main parameters including ultrasound time (A), pH (B), salt concentration (C), and volume of miscible organic solvent (D). In this technique, a mixture of plant sample and extraction solvent was subjected to ultrasound waves. After ultrasound‐assisted extraction, phase separation was performed by the addition of salt to the liquid phase. The optimal conditions for the highest extraction yield of oleuropein were ultrasound time, 30 min; volume of organic solvent, 2.5 mL; salt concentration, 25% w/v; and sample pH, 4. Experimental data were fitted with a quadratic model. Analysis of variance results show that BC interaction, A², B², C², and D² are significant model terms. Unlike the conventional extraction methods for plant extracts, no evaporation and reconstitution operations were needed in the proposed technique.     

High‐density extraction solvent‐based solvent de‐emulsification dispersive liquid–liquid microextraction combined with MEKC for detection of chlorophenols in water samples

For the first time, the high‐density solvent‐based solvent de‐emulsification dispersive liquid–liquid microextraction (HSD‐DLLME) was developed for the fast, simple, and efficient determination of chlorophenols in water samples followed by field‐enhanced sample injection with reverse migrating micelles in CE. The extraction of chlorophenols in the aqueous sample solution was performed in the presence of extraction solvent (chloroform) and dispersive solvent (acetone). A de‐emulsification solvent (ACN) was then injected into the aqueous solution to break up the emulsion, the obtained emulsion cleared into two phases quickly. The lower layer (chloroform) was collected and analyzed by field‐enhanced sample injection with reverse migrating micelles in CE. Several important parameters influencing the extraction efficiency of HSD‐DLLME such as the type and volume of extraction solvent, disperser solvent and de‐emulsification solvent, sample pH, extraction time as well as salting‐out effects were optimized. Under the optimized conditions, the proposed method provided a good linearity in the range of 0.02–4 μg/mL, low LODs (4 ng/mL), and good repeatability of the extractions (RSDs below 9.3%, n = 5). And enrichment factors for three phenols were 684, 797, and 233, respectively. This method was then utilized to analyze two real environmental samples from wastewater and tap water and obtained satisfactory results. The obtained results indicated that the developed method is an excellent alternative for the routine analysis in the environmental field.     

Biosurfactant trehalose lipid‐enhanced ultrasound‐assisted micellar extraction and determination of the main antioxidant compounds from functional plant tea

Hydrosoluble trehalose lipid (a biosurfactant) was employed for the first time as a green extraction solution to extract the main antioxidant compounds (geniposidic acid, chlorogenic acid, caffeic acid, and rutin) from functional plant tea (Eucommia ulmoides leaves). Single‐factor tests and response surface methodology were employed to optimize the extraction conditions for ultrasound‐assisted micellar extraction combined with ultra‐high‐performance liquid chromatography in succession. A Box‐Behnken design (three‐level, three‐factorial) was used to determine the effects of extraction solvent concentration (1–5 mg/mL), extraction solvent volume (5–15 mL), and extraction time (20–40 min) at a uniform ultrasonic power and temperature. In consequence, the best analyte extraction yields could be attained when the trehalose lipid solution concentration was prepared at 3 mg/mL, the trehalose lipid solution volume was 10 mL and the extraction time was set to 35 min. In addition, the recoveries of the antioxidants from Eucommia ulmoides leaves analyzed by this analytical method ranged from 98.2 to 102%. These results indicated that biosurfactant‐enhanced ultrasound‐assisted micellar extraction coupled with a simple ultra‐high‐performance liquid chromatography method could be effectively applied in the extraction and analysis of antioxidants from Eucommia ulmoides leaf samples.     

Surface-Ionization Mass Spectrometry of Opium Alkaloids

Surface ionization of the opium alkaloids morphine, codeine, thebaine, papaverine, and narcotine was investigated by mass spectrometry. It was shown that the alkaloid molecules were ionized with high efficiency through surface ionization. The mass spectra of morphine, codeine, and thebaine exhibited series of lines for quasimolecular ions with elimination of up to nine H atoms from the opiates that was accompanied by heterogeneous aromatization of the rings and their skeletal rearrangement. The results were compared with GC-MS data from electron ionization.     

红花罂粟植物的各个部分中蒂巴因含量的测定

采用甲醇浸泡、超声波一次提取处理样品,气相色谱内标法定量测定不同种类及不同培育方法的红花罂粟植物的全果、根、叶、苞片、果盖、果壳、茎中蒂巴因的含量。方法采用多点校正,其线性相关系数为０．９９６,变异系数为２．９％～５．４％,最低绝对检出量可达２ｎｇ。蒂巴因的色谱峰为双峰,经质谱确证为异构体,这两种异构体的比例不固定,取其峰面积之和定量。应用该方法对前后３年共１６８个样品进行了测定,提取样品中蒂巴因的图谱与蒂巴因标准品的图谱完全一致,样品中的其它杂质均不干扰蒂巴因的测定。     

The use of CE-electrochemiluminescence with ionic liquid for the determination of bioactive constituents in Chinese traditional medicine

CE / tris(2,2-bipyridyl) ruthenium(II) (Ru(bpy)(3) (2+)) electrochemiluminescence (ECL), CE-ECL, with an ionic liquid (IL) detection system was established for the determination of bioactive constituents in Chinese traditional medicine opium poppy which contain large amounts of coexistent substances. A minimal sample pretreatment which involves a one-step extraction approach avoids both sample loss and environmental pollution. As the nearby hydroxyl groups in some alkaloid such as morphine may react with borate to form complexes and IL, as a high-conductivity additive in running buffer, could cause an enhanced field-amplified effect of electrokinetic injection. Running buffer containing 25 mM borax-8 mM 1-ethyl-3-methylimidazolium tetrafluoroborate (EMImBF(4))IL (pH 9.18) was used which resulted in significant changes in separation selectivity and obvious enhancement in ECL intensities for those alkaloids with similar structures. Sensitive detection could be achieved when the distance between the Pt working electrode and the outlet of separation capillary was set at 150 microm and the stainless steel cannula was fixed approximately 1 cm away from the outlet of the capillary. Quantitative analysis of four alkaloids was achieved at a detection voltage of 1.2 V and a separation voltage of 15 kV in less than 7 min. Detection limits of thebaine, codeine, morphine, and narcotine were 2.5 x 10(-7), 2.5 x 10(-7), 1 x 10(-9) and 1 x 10(-6) M(S/N = 3), respectively. The method was successfully applied to determine the amounts of opium alkaloids in real poppy samples.