Effects of heat and pressure on intercalation structures of isobutylene‐isoprene rubber/clay nanocomposites. I. Prepared by melt blending

In this work, the effects of heat and pressure on intercalated structures of isobutylene‐isoprene rubber/clay nanocomposites (IIRCNs) prepared by melt blending were investigated. Not only the local intercalated structures were monitored by wide‐angle X‐ray diffraction, but also the spatial distributions of intercalated structures were observed by transmission electron microscope. The experimental result reveals that the intercalated structures and their spatial distributions in the matrix are extensively altered by the thermal treatment at atmospheric or higher pressure. The possible microstructural models for untreated and treated IIRCNs were put forward. The observed phenomena were interpreted from the viewpoints of thermodynamics and kinetics theories as well as the feature of rubber. Finally, guidelines were proposed for designing curing system to achieve desired intercalated/exfoliated morphology. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2653–2664, 2005     

Multilayer graphene/chlorine‐isobutene‐isoprene rubber nanocomposites: the effect of dispersion

Multilayer graphene (MLG) is composed of approximately 10 sheets of graphene. It is a promising nanofiller just starting to become commercially available. The dispersion of the nanofiller is essential to exploit the properties of the nanocomposites and is dependent on the preparation method. In this study, direct incorporation of 3 parts per hundred of rubber (phr) MLG into chlorine‐isobutene‐isoprene rubber (CIIR) on a two‐roll mill did not result in substantial enhancement of the material properties. In contrast, by pre‐mixing the MLG (3 phr) with CIIR using an ultrasonically assisted solution mixing procedure followed by two‐roll milling, the properties (rheological, curing, and mechanical) were improved substantially compared with the MLG/CIIR nanocomposites mixed only on the mill. The Young's moduli of the nanocomposites mixed in solution increased by 38%. The CIIR/MLG nanocomposites produced via solution showed superior durability against weathering exposure. Copyright © 2016 John Wiley & Sons, Ltd.     

Exploitation of introducing of catalytic centers into layer galleries of layered silicates and related epoxy nanocomposites. I. Epoxy nanocomposites derived from montmorillonite modified with catalytic surfactant‐bearing carboxyl groups

Montmorillonite (MMT) was modified with the acidified cocamidopropyl betaine (CAB) and the resulting organo‐montmorillonite (O‐MMT) was dispersed in an epoxy/methyl tetrahydrophthalic anhydride system to form epoxy nanocomposites. The intercalation and exfoliation behavior of the epoxy nanocomposites were examined by X‐ray diffraction and transmission electron microscopy. The curing behavior and thermal property were investigated by in situ Fourier transform infrared spectroscopy and DSC, respectively. The results showed that MMT could be highly intercalated by acidified CAB, and O‐MMT could be easily dispersed in epoxy resin to form intercalated/exfoliated epoxy nanocomposites. When the O‐MMT loading was lower than 8 phr (relative to 100 phr resin), exfoliated nanocomposites were achieved. The glass‐transition temperatures (T_g's) of the exfoliated nanocomposite were 20 °C higher than that of the neat resin. At higher O‐MMT loading, partial exfoliation was achieved, and those samples possessed moderately higher T_g's as compared with the neat resin. O‐MMT showed an obviously catalytic nature toward the curing of epoxy resin. The curing rate of the epoxy compound increased with O‐MMT loading. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1192–1198, 2004     

Thermal and morphological characteristics of solution blended epoxy/NBR compound

Systematic study about the effect of acrylonitrile–butadiene rubber (NBR) concentration on the fracture toughness and thermal behavior of epoxy resin is conducted in this study. NBR is solved in an aromatic hydrocarbon solvent and is added to epoxy resin. We used diethylene-teriamin as the curing agent for epoxy resin. Tensile test results, performed followed by molding procedure, show that the toughness is improved owing to the increase of rubber content. Scanning electron microscopy (SEM) and atomic force microscopy besides thermogravimetric analysis (TG) are used to investigate the epoxy/rubber interface and chemical decomposition of the resultant mixture. The thermal behavior of cured epoxy resin was analyzed via TG instrument at different heating rates. Thermogravimetry curves showed that the thermal decomposition of epoxy system was occurred in only one stage regardless of the rubber content. The apparent activation energies of the rubber/epoxy systems containing 0, 5, and 10 phr of rubber were determined by Flynn–Wall–Ozawa, Kissinger–Akahira–Sunose, and Friedman methods. The results prove that the thermal stability of epoxy resin was decreased with enhancing the rubber content. However, the trend of changing activation energy versus conversions is totally different followed by adding the elastomer to the system compared to neat epoxy resin. Moreover, the results obtained via our proposed facile solution blending method are compared to those of resins modified with nano-powdered elastomer.     

Preparation and characterization of vinylidene chloride‐co‐vinyl chloride copolymer/fluorinated synthetic mica nanocomposites I thermal and mechanical properties studies

Poly(vinylidene chloride‐co‐vinylchloride)/organically modified fluorinated synthetic mica (MEE) (VDC‐VC/MEE) nanocomposites were prepared by melt blending of VDC‐VC copolymer with MEE, in the presence of dioctyl phthalate (DOP) which acted as a plasticizer and a cointercalating agent. The nanostructure, thermal, and dynamic mechanical properties of the VDC‐VC/MEE nanocomposites were studied by wide angle X‐ray diffractometer (WAXD), scanning electron microscope (SEM), transmission electron microscope (TEM), thermogravimetric analyzer (TGA), and dynamic mechanical analyzer (DMA). It was found that partially intercalated and partially exfoliated structures coexisted in VDC‐VC/MEE nanocomposities. Below 8 wt % MEE content, the intercalation effect of nanocomposites decreased with increasing the MEE content. Under a nitrogen atmosphere, VDC‐VC/MEE nanocomposites exhibited a single step thermal degradation behavior. The nanostructure of VDC‐VC/MEE can effectively prevent volatile gases from being released, and thus enhances its thermal stability. The thermal stability of VDC‐VC/MEE nanocomposites is strongly related to the morphology of nanocomposites and the degraded composites structure. DMA revealed a significant improvement in the storage modulus within the testing temperature range. The increase in storage modulus depends on the MEE content, which is attributed to the dispersed phase morphology. The glass transition temperature of VDC‐VC/MEE nanocomposites is affected by the chain mobility in the nanocomposites rather than the aggregative morphology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1214–1225, 2008     

Effect of halloysite nanotube on microstructure,rheological and mechanical properties of dynamically vulcanized PA6/NBR thermoplastic vulcanizates

Dynamically vulcanized thermoplastic vulcanizate (TPV) nanocomposites based on polyamide-6 (PA6) and acrylonitrile butadiene rubber (NBR) reinforced by halloysite nanotubes (HNT) were prepared via a direct melt mixing process. The effects of HNT on the physical, mechanical, and rheological properties of nanocomposites were investigated. The prepared PA6/NBR/HNT nanocomposites were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), differential scanning colorimeter (DSC), dynamic mechanical thermal analysis (DMTA), and rheological measurements. The morphology study of prepared nanocomposites shows that the introduction of HNT into the PA6 phase causes a decrease in the size of NBR droplets. The mechanical measurements revealed that Young’s modulus of TPV nanocomposites increased with the HNT loading up to 54%. DMTA results show that the introduction of 10 wt% of HNT into the PA6/NBR TPV leads to a 30% increase in storage modulus. The rheological measurements revealed that the storage modulus of nanocomposites has an increase of more than 200% in the presence of 7 wt% of HNT loading. Analytical stiffness modeling of Young’s modulus of the TPV nanocomposites was investigated using Hui–Shia and Wu models. Both models have some deviations from experimental results and been modified to predict Young’s modulus of the nanocomposites containing HNT with more precisions. The viscosity behavior of TPV nanocomposites was studied using a Carruea–Yasuda model and showed that the yield stress of nanocomposites increases with higher HNT loadings, indicating the formation of a nanotube network along with NBR phase network.     

Prevulcanized natural rubber latex/clay aerogel nanocomposites

Natural rubber latex (NR)/clay aerogel nanocomposites were produced via freeze-drying technique. The pristine clay (sodium montmorillonite) was introduced in 1-3 parts per hundred rubber (phr) in order to study the effect of clay in the NR matrix. The dispersion of the layered clay and the morphology of the nanocomposites were determined by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Cure characteristics, thermal stability, and the crosslink density of thermal and microwave-cured NR and its composites were investigated. XRD patterns indicated that both intercalated and exfoliated structures were observed at loadings of 1-3 phr clay. SEM studies revealed that the clay aerogel structure was formed at 3 phr clay loading. The increment in Shore A hardness of nanocomposites compared with pure NR signified excellent polymer/filler interaction and the reinforcing effect of the clay to rubber matrix. This was supported by an increase in maximum rheometric torque and crosslink density. The crosslink density of clay-filled NR vulcanizate was found to increase with the pristine clay content in both thermal and microwave curing methods. However, microwave-cured 2 and 3 phr-filled NR vulcanizates exhibited higher crosslink density than those which were thermal-cured under the same curing temperature. In addition, thermal stability studies showed that pristine clay accelerated the decomposition of NR by showing a slight decrease in onset and peak decomposition temperatures along with clay content.     

Influence of carboxyl‐terminated (butadiene‐co‐acrylonitrile) loading on the mechanical and thermal properties of cured epoxy blends

A mixture of epoxy with liquid nitrile rubber, carboxyl‐terminated (butadiene‐co‐acrylonitrile) (CTBN) was cured under various temperatures. The cured resin was a two‐phase system, where spherical rubber domains were dispersed in the matrix of epoxy. The morphology development during cure was investigated by scanning electron microscope (SEM). There was slight reduction in the glass transition temperature of the epoxy matrix (T_g) on the addition of CTBN. It was observed that, for a particular CTBN content, T_g was found to be unaffected by the cure temperature. Bimodal distribution of particles was noted by SEM analysis. The increase in the size of rubber domains with CTBN content is due probably to the coalescence of the rubber particles. The mechanical properties of the cured resin were thoroughly investigated. Although there was a slight reduction in tensile strength and young's modulus, appreciable improvements in impact strength, fracture energy, and fracture toughness were observed. Addition of nitrile rubber above 20 parts per hundred parts of resin (phr) made the epoxy network more flexible. The volume fraction of dispersed rubbery phase and interfacial area were increased with the addition of more CTBN. A two‐phase morphology was further established by dynamic mechanical analysis (DMA). © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2531–2544, 2004     

Dynamic mechanical behavior of acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δ_max were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002     

Shear‐induced change of exfoliation and orientation in polypropylene/montmorillonite nanocomposites

For the improved dispersion of montmorillonite (MMT) in a polypropylene (PP) matrix, PP/MMT nanocomposites prepared via direct melt intercalation were further subjected to oscillating stress achieved by dynamic packing injection molding. The shear‐induced morphological changes were investigated with an Instron machine, wide‐angle X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The original nanocomposites possessed a partly intercalated and partly exfoliated morphology. A transformation of the intercalated structure into an exfoliated structure occurred after shearing, and a more homogeneous dispersion of MMT in the PP matrix was obtained. However, the increase of the exfoliated structure was accompanied by the scarifying of the orientation of MMT layers along the shear direction. Some bended or curved MMT layers were found for the first time by TEM after shearing. However, the orientation of PP chains in the PP/MMT nanocomposites became very difficult under an external shear force; this indicated that the molecular motion of PP chains intercalated between MMT layers was highly confined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1–10, 2003     

Electrically conductive acrylonitrile–butadiene rubber elastomers prepared by dopamine‐induced surface functionalization and metallization

A novel method for the preparation of electrical conductive surface silvered acrylonitrile–butadiene rubber (NBR) was developed. Dopamine was spontaneously oxide polymerized and deposited onto the surface of NBR. Electroless plating of silver was carried out on the poly(dopamine) (PDA)‐functionalized NBR surface. The composition of the NBR surface was studied by X‐ray photoelectron spectroscopy (XPS). XPS results showed that PDA was successfully deposited onto the NBR surface. The morphology of the NBR surface was observed by scanning electron microscopy (SEM). The SEM images showed that PDA had formed a distinctive layer ready for electroless deposition of silver. The catechol/quinone groups on the PDA molecular structure can be used as binding sites for silver ions. The silvered NBR showed high surface conductivity of 1.4 Ω. Copyright © 2011 John Wiley & Sons, Ltd.     

Effects of epoxidized natural rubber as a compatibilizer in melt compounded natural rubber-organoclay nanocomposites

Nanocomposites containing natural rubber (NR) as matrix, epoxidized natural rubber (ENR) as compatibilizer and organophilic layered clay (organoclay) as filler were produced in an internal mixer and cured using a conventional sulphuric system. The effects of ENR with 25 (ENR 25) and 50 mol% epoxidation (ENR 50), respectively, were compared at 5 and 10 parts per hundred rubber (phr) concentrations. The organoclay content was fixed at 2 phr. Cure characteristics, clay dispersion, (thermo)mechanical properties of the nanocomposites were determined and discussed. Incorporation of ENR and organoclay strongly affected the parameters which could be derived from Monsanto MDR measurements. Faster cure and increased crosslink density were attributed to changes in the activation/crosslinking pathway which was, however, not studied in detail. The organoclay was mostly intercalated according to X-ray diffraction (XRD) and transmission electron microscopic (TEM) results. The best clay dispersion was achieved by adding ENR 50. This was reflected in the stiffness of the nanocomposites derived from both dynamic mechanical thermal analysis (DMTA) and tensile tests. The tensile and tear strengths of the ENR 50 containing nanocomposites were also superior to the ENR 25 compatibilized and uncompatibilized stocks.     

Thermal and mechanical properties of a dendritic hydroxyl‐functional hyperbranched polymer and tetrafunctional epoxy resin blends

Blends of a tetrafunctional epoxy resin, tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM), and a hydroxyl‐functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 3,3′‐diaminodiphenyl sulfone (DDS) as curing agent. The phase behavior and morphology of the DDS‐cured epoxy/HBP blends with HBP content up to 30 phr were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The phase behavior and morphology of the DDS‐cured epoxy/HBP blends were observed to be dependent on the blend composition. Blends with HBP content from 10 to 30 phr, show a particulate morphology where discrete HBP‐rich particles are dispersed in the continuous cured epoxy‐rich matrix. The cured blends with 15 and 20 phr exhibit a bimodal particle size distribution whereas the cured blend with 30 phr HBP demonstrates a monomodal particle size distribution. Mechanical measurements show that at a concentration range of 0–30 phr addition, the HBP is able to almost double the fracture toughness of the unmodified TGDDM epoxy resin. FTIR displays the formation of hydrogen bonding between the epoxy network and the HBP modifier. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 417–424, 2010     

The physical and mechanical properties and cure characteristics of NBR/silica/MWCNT hybrid composites

The main objective of the present study was to investigate the synergistic effect of simultaneous use of two reinforcing fillers in rubber compounds based on acrylonitrile-butadiene copolymer (NBR). Silica was used as reinforcing filler in all samples and the loading content was 25 phr. 3 and 5 phr of multiwall carbon nanotubes (MWCNT) were used as second reinforcing filler in NBR/silica compounds. Melt mixing method was employed for compound preparation. The effects of carbon nanotube/silica hybrid filler on mechanical and vulcanization characteristics of the rubber compounds were investigated. These results revealed that addition of the reinforcing filler, either carbon nanotube or silica, shortened the optimum cure time (t₉₀) and also scorch time (t_s1) of samples compared to that of pure NBR compound. In hybrid compounds, the reduction in optimum cure time and scorch time was higher than that of for silica-filled NBR or CNT-filled NBR compounds. This can be attributed to the synergistic effect between CNT and silica as two reinforcing agents in NBR compounds. Regardless the composition of the reinforcing filler, an increase of the relaxed storage modulus is observed, while the tan δ value is decreased steadily. The dynamic modulus reinforcement of nanocomposites was examined by the Guth Gold and Modified Guth Gold equations. For hybrid samples, the experimental values show a significant positive deviation from model predictions. According to the Barlow’s formula, hybrid compounds show higher burst strength compared to silica or CNT filled NBR compounds.     

Application of strain-time correspondence as a tool for structural analysis of acrylonitrile-butadiene copolymer nanocomposites with various organoclay loadings

Acrylonitrile-butadiene copolymer (NBR) nanocomposites were prepared with varied silicate loadings by the melt mixing between NBR and organoclays (OCs) containing intercalants with different polarity and chain length. WXRD exhibited that the NBR nanocomposites had an intercalated structure with distinct differences in gallery height depending on the intercalant characteristics. However, WXRD failed to show a structural change with increasing silicate contents. Hence, tensile strain-stress measurements were carried out at various strain rates (0.162, 0.0975, and 0.0187 s⁻¹), and then the results of tensile measurement applied to the strain-time correspondence (STC) principle, resulting in the tensile modulus master curves of the NBR nanocomposites as a function of time. For pure NBR, a master curve was constructed using only the horizontal shift factor, indicating that the material was structurally homogeneous. However, the NBR nanocomposites required both vertical shift (modulus shift, Γ(α)) and horizontal shift to form the master curves, indicating structural heterogeneity ascribed to the domain structure such as silicate tactoid. From master curves, we found that NBR nanocomposite with OC having polar organic intercalant, NBROC30B, had the lowest n value in the nanocomposites. This indicates that NBROC30B had the most dispersive silicate structure in the nanocomposites due to the polar interaction, being in good agreement with WXRD results. In particular, STC was not applicable at all nanocomposites with silicate loadings over 8 wt%, regardless type of organoclay, and tensile strength and toughness of the nanocomposites with silicate loading of 8 wt% were better than expected. These could be explained as the network-like percolation of the silicate tactoids in all nanocomposites with silicate loadings over 8 wt%, which were consistent with the results observed from HR-TEM.     

Studies of ABS-graft-maleic anhydride/clay nanocomposites: Morphologies, thermal stability and flammability properties

ABS-g-MAH (maleic anhydride) with different grafting degree, ABS/OMT (organo montmorillonite) and ABS-g-MAH/OMT nanocomposites were prepared via melt blending. The grafting reaction, phase morphology, clay dispersion, thermal properties, dynamic mechanical properties and flammability properties were investigated. FTIR spectra results indicate that maleic anhydride was successfully grafted onto butadiene chains of the ABS backbone in the molten state using dicumyl peroxide as the initiator and styrene as the comonomer and the relative grafting degree increased with increasing loading of MAH. TEM images show the size of the dispersed rubber domains of ABS-g-MAH increased and the dispersion is more uniform than that of neat ABS resin. XRD and TEM results show that intercalated/exfoliated structure formed in ABS-g-MAH/OMT nanocomposites and the rubber phase intercalated into clay layers distributed in both SAN phase and rubber phase. TGA results reveal the intercalated/exfoliated structure of ABS-g-MAH/OMT nanocomposites has better barrier properties and thermal stability than intercalated ones of ABS/OMT nanocomposites. The T_g of ABS-g-MAH/OMT nanocomposites was also higher than that of neat ABS/OMT nanocomposites. The results of cone measurements show that ABS-g-MAH/OMT nanocomposites exhibit significantly reduced flammability when compared to ABS/OMT nanocomposites even at the same clay content. The chars of ABS-g-MAH/OMT nanocomposites were tighter, denser, more integrated and fewer surface microcracks than ABS/OMT residues.     

Design of PP/EPDM/NBR TPVs with tunable mechanical properties via regulating the core-shell structure

In this work, polypropylene (PP)/ethylene-propylene-diene monomer (EPDM)/butadiene acrylonitrile rubber (NBR) TPVs with different EPDM/NBR ratios were prepared by the core-shell dynamic vulcanization. The relationship between the core-shell structure and mechanical properties of the TPVs were thoroughly investigated. The formation of core-shell structure by adding NBR is conducive to the mechanical properties of the TPVs. The ratio of EPDM to NBR has an important effect on the structure and performances of the final products, and there is a critical ratio for this effect change. Transmission electron microscope (TEM), tensile test, reprocessing test, ageing test, rheological behavior test and stress relaxation were used to characterize the morphology and properties of the TPVs in detail. It was found that when the ratio of EPDM/NBR was 2:4, the tensile strength increased by ~14% compared with PP/EPDM TPV without NBR. Meanwhile, the reprocessing properties, rheological characteristics and instantaneous tensile deformation, etc. all exhibited sudden changes at this critical ratio.     

Effect of cold plasma process on the surface wettability of NBR and the kerosene resistance of NBR/PTFE composites

In this study, first the acrylonitrile‐butadiene rubber (NBR5080) was modified by argon (Ar), air, and oxygen plasma at low temperature, and the effect of plasma process (power, time, and pressure) on the surface properties of NBR5080, the interfacial properties, physical properties, and the mechanical properties of NBR5080/polytetrafluoroethylene (PTFE) composites were investigated. The state contact angle and the surface free energy were applied to characterize the surface wettability of NBR5080. The scanning electron microscope and the atomic force microscope were used to observe the surface morphology of the NBR5080. The chemical changes on the NBR5080 surface were verified by X‐ray photoelectron spectroscopy. The average water contact angle the NBR5080 declined obviously when NBR5080 was treated by Ar (100 W/600 s/30 Pa). The active oxygen groups were introduced onto the surface of NBR5080 by cold plasma treatment and more active group containing oxygen were observed on the samples treated by Ar plasma. The peel strength between the NBR5080 and the PTFE was increased obviously, which increased from 0 to 44.2 N?m^?1 for Ar plasma treatment. The mass and the dimension of NBR5080 increase sharply after immersing in kerosene, whereas the NBR5080/PTFE composites changed a little. The mechanical properties of NBR5080 and NBR5080/PTFE composites decreased as the immersion time in kerosene increased, but the decreased degree of NBR5080 is higher than NBR5080/PTFE composites.     

Nanotailoring of sepiolite clay with poly [styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene]: structure–property correlation

Poly [styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS)/sepiolite clay nanocomposites are prepared by solvent casting method. Two types of schemes have been adopted to establish the compatibility between nonpolar polymer (SEBS) and needle‐like inorganic filler (sepiolite), either by polar modification of the nonpolar polymer or organic modification of the inorganic filler. Structure–property correlation of nanocomposites derived from two different approaches is compared. Structural and morphological analysis of nanocomposites has been investigated by Fourier transform infrared spectroscopy, X‐ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. Fourier transform infrared result shows better compatibility between SEBS and modified sepiolite clay compared to maleic anhydride grafted SEBS and pristine sepiolite in their nanocomposites. Tensile strength and % elongation are found to increase by 32 and 105%, respectively, with the addition of just 3 parts per hundred parts of resin (phr) modified sepiolite clay to pristine SEBS matrix. Moreover, thermal stability has also improved by 96°C with similar loading. This work provides a new insight into the structure and thermo‐mechanical properties of novel SEBS–sepiolite clay nanocomposites. Copyright © 2017 John Wiley & Sons, Ltd.     

Thermal and dynamic mechanical properties of epoxy resin/poly(urethane‐imide)/polyhedral oligomeric silsesquioxane nanocomposites

Linear isocyanate‐terminated poly(urethane‐imide) (PUI) with combination of the advantages of polyurethane and polyimide was directly synthesized by the reaction between polyurethane prepolymer and pyromellitic dianhydride (PMDA). Then octaaminophenyl polyhedral oligomeric silsesquioxane (OapPOSS) and PUI were incorporated into the epoxy resin (EP) to prepare a series of EP/PUI/POSS organic–inorganic nanocomposites for the purpose of simultaneously improving the heat resistance and toughness of the epoxy resin. Their thermal degradation behavior, dynamic mechanical properties, and morphology were studied with thermal gravimetric analysis (TGA), dynamic mechanical analysis (DMA), and transmission electron microscope (TEM). The results showed that the thermal stability and mechanical modulus was greatly improved with the addition of PUI and POSS. Moreover, the EP/PUI/POSS nanocomposites had lower glass transition temperatures. The TEM results revealed that POSS molecules could self assemble into strip domain which could switch to uniform dispersion with increasing the content of POSS. All the results could be ascribed to synergistic effect of PUI and POSS on the epoxy resin matrix. Copyright © 2010 John Wiley & Sons, Ltd.