Molecular imprinting of natural flavonoid antioxidants: application in solid-phase extraction for the sample pretreatment of natural products prior to HPLC analysis

As shown in the past years, SPE based on molecularly imprinted polymers (MIPs) may provide significant enhancement of selectivity in sample preparation and analyte preconcentration. The objective of this work was the fabrication of MIPs for the specific adsorption of rutin and quercetin. The two flavonoids were used as the template molecules for the preparation of MIP phases in a self-assembly (noncovalent) approach. The produced MIPs were validated with regard to the imprinting efficiency as media for LC and SPE. The retention behavior of several flavonoid compounds was studied using as stationary phases imprinted, control nonimprinted polymers, and commercial silica-based materials. MIPs were applied as materials for the selective SPE and preconcentration of the flavonoids from white and red wine, orange juice, and tea. The collected fractions were analyzed by high-pressure LC. MIP-SPE facilitated specific analyte isolation and effective sample clean-up. The results show that molecularly imprinted SPE can be a useful tool for the simple, selective, and cost-effective pretreatment of samples containing natural antioxidants.     

Development and application of molecularly imprinted polymers as solid-phase sorbents for erythromycin extraction

Six molecularly imprinted polymers (MIPs) of erythromycin (ERY) were prepared by noncovalent bulk polymerization using methacrylic acid (MAA) as the functional monomer. On the basis of binding analysis, the MIPs with 1:2 optimum ratio of template to MAA were selected for subsequent scanning electron microscopy and Brunauer–Emmett–Teller analyses, which indicated that the MIPs had more convergent porous structures than the nonimprinted polymers. The equilibrium binding experiments showed that the binding sites of MIPs were heterogeneous, with two dissociation constants of 0.005 and 0.63 mg mL⁻¹, respectively. Furthermore, the performance of the MIPs as solid-phase extraction (SPE) sorbents was evaluated, and the selectivity analysis showed that the MIPs could recognize ERY with moderate cross-reactivity for other macrolides. The overall investigation of molecularly imprinted SPE for cleanup and enrichment of the ERY in pig muscle and tap water confirmed the feasibility of utilizing the MIPs obtained as specific SPE sorbents for ERY extraction in real samples. Figure Schematic diagram of the preparation and application of the erythromycin imprinted molecularly imprinted polymers Suquan Song and Aibo Wu contributed equally to this work.     

Molecularly imprinted polymer nanocarriers for recognition and sustained release of diclofenac

In this study, a series of imprinted poly(methacrylic acid‐co‐ethylene glycol dimethacrylate) nanocarriers for diclofenac and corresponding nonimprinted polymer nanocarriers have been synthesized in 4 different types of solvents by precipitation polymerization. The products were characterized by Fourier transform infrared, scanning electron microscopy, dynamic light scattering, and Brunauer‐Emmett‐Teller measurement. Results showed that uniformly sized molecularly imprinted polymer (MIP) nanospheres with relatively good porosity could only be obtained in acetonitrile. The effects of solvents on the recognition and release properties of polymer particles were also carefully investigated. The binding experiments indicated that MIPs prepared in acetonitrile displayed much higher binding capacity than other MIPs with a maximum binding capacity of 65.18 mg g⁻¹. The Scatchard analysis showed that synthetic MIPs have special recognition sites for diclofenac, while nonimprinted polymers have not. The Sips model could provide a best fit to the equilibrium data of nanocarriers over whole concentrations. The experimental data of an adsorption kinetic study were well fitted to the pseudo–second‐order kinetic model, indicating the chemisorption mechanism between diclofenac and MIPs in the process of adsorption. The drug release of diclofenac from MIPs could well be described by the Ritger‐Peppas model, suggesting a non‐Fickian diffusion mechanism. In addition, we successfully used MIPs to extract diclofenac at low levels from fetal bovine serum.     

利用分子印迹技术预处理生物样品中头孢药物的研究

优化了头孢硫脒分子印迹聚合物的合成条件,探讨了分子印迹技术和固相萃取联用对血浆中头孢硫脒的分离富集,发现用4-乙烯基吡啶作功能单体合成的分子印迹聚合物作为固相萃取填充料,能定量吸附血浆中的头孢硫脒,并初步研究了其吸附机理。     

Molecularly imprinted polymers with synthetic dummy templates for the preparation of capsaicin and dihydrocapsaicin from chili peppers

In this work, dummy molecularly imprinted polymers with high selectivity and affinity to capsaicin and dihydrocapsaicin are designed using N‐vanillylnonanamide as a dummy template. The performance of dummy molecularly imprinted polymers and nonimprinted polymers was evaluated using adsorption isotherms, adsorption kinetics, and selective recognition capacity. Dummy molecularly imprinted polymers were found to exhibit good site accessibility, taking just 20 min to achieve adsorption equilibrium; they were also highly selective toward capsaicin and dihydrocapsaicin. We successfully used dummy molecularly imprinted polymers as a specific sorbent for selectively enriching capsaicin and dihydrocapsaicin from chili pepper samples. In a scaled‐up experiment, the selective recovery of capsaicinoids was calculated to be 77.8% using solid‐phase extraction. To the best of our knowledge, this is the first example of the use of N‐vanillylnonanamide as a dummy template in molecularly imprinted polymers to simultaneously enrich capsaicin and dihydrocapsaicin.     

Development of molecularly imprinted polymeric nanofibers by electrospinning and applications to pesticide adsorption

Novel polystyrene‐based molecularly imprinted polymer nanofibers were synthesized through the electrospinning technique. The molecularly imprinted polymers were prepared using a non‐covalent approach and atrazine as template. For comparison, nonimprinted polymer nanofibers were also synthesized. The morphology of the synthesized nanofibers was characterized using scanning electron microscopy. The adsorption of pesticides, atrazine, atrazine desisopropyl, atraton, carboxin, linuron, and chlorpyrifos was studied under equilibrium (batch) conditions. To describe the adsorption capability of the synthesized polymers, Langmuir and Freundlich models were used. The Freundlich model provided a better mathematical approximation of the sorption characteristic for polymers nanofibers. To evaluate the adsorption capacity in the presence of interferents experiments on river water samples spiked with a mixture of six pesticides were also performed. The results obtained for the highest concentration levels investigated, show a greater amount of pesticide adsorbed on molecularly imprinted polymers and non‐imprinted polymers compared to those obtained using commercial stationary phases used as reference.     

Simultaneous determination of quinoxaline‐1,4‐dioxides in feeds using molecularly imprinted solid‐phase extraction coupled with HPLC

A simple, selective, and reproducible molecularly imprinted SPE coupled with HPLC method was developed for monitoring quinoxaline‐1,4‐dioxides in feeds. Molecularly imprinted polymers were synthesized in methanol using mequindox (MEQ) as template molecule and acrylamide as functional monomer by bulk polymerization. Under the optimum SPE conditions, the novel polymer sorbents can selectively extract and enrich carbadox, MEQ, quinocetone, and cyadox from a variety of feeds. The molecularly imprinted SPE cartridge was better than nonimprinted, C₁₈, and HLB cartridges in terms of both recovery and precision. Mean recoveries of four quinoxaline‐1,4‐dioxides from six kinds of feeds spiked at 1.0, 10, and 100 mg/kg ranged between 75.2 and 94.7% with RSDs of less than 10%. The decision limits (CCαs) and the detection capabilities (CCβs) of four analytes were 0.15–0.20 mg/kg and 0.44–0.56 mg/kg, respectively. The class selectivity of the polymers was evaluated by checking three drugs with different molecular structures to that of MEQ.     

Molecularly Imprinted Polymers for Solid Phase Extraction

The combination of molecularly imprinted polymers (MIPs) and solid phase extraction (SPE) is reviewed. MIPs, which have high selectivity and affinity for a predetermined molecule (template), have been used as sorbents for SPE to selectively isolate analytes from biological, pharmaceutical, and environmental samples. Solid phase extraction with molecularly imprinted polymers (MIP–SPE) is a promising technique which allows specific analytes to be selectively extracted from complex matrices. This survey summarizes the characteristics, development and application of MIP–SPE in recent years. Existed problems and the future direction of MIP–SPE are also discussed.     

Synthesis of Molecularly Imprinted Polymer for Removal of Effective Impurity (Benzhydrol) from Diphenhydramine Hydrochloride Drug

The present study describes the synthesis and preliminary testing of molecularly imprinted polymers (MIPs) as scavenger resins for removal of the genotoxic impurities (GTI) benzhydrol from active pharmaceutical ingredients (API). A new molecularly imprinted polymer was synthesized using benzhydrol (template molecule), methacrylic acid (functional monomer), ethylene glycol dimethacrylate (cross‐linker), 2,2′‐azobisisobutironitril (intiator) and chloroform (porogenic solvent). To compare the performance of this polymer, a control polymer or non‐imprinted polymer (NIP) was prepared under the same conditions without the use of template molecule. The synthesized polymers were characterized by FT‐IR spectroscopy. Selectivity of the molecularly imprinted polymer for absorption benzhydrol impurities through adsorption experiments reviews and the results were compared with the adsorption of impurities by NIP. Various parameters were optimized such as time, pH, type of eluent for elution of impurities from polymer, concentration of sample and saturation of polymer. The proposed method was applied for removal of benzhydrol from Diphenhydramine hydrochloride syrup and passing it through the MIPs led to the quantitative removal of benzhydrol.     

Preparation and Recognition Properties of Vanillin‐Imprinted Polymers

Some new molecularly imprinted polymers (MIPs) were prepared by different protocols involving vanillin as the imprinted molecule, methacrylic acid (= 2‐methylprop‐2‐enoic acid; MAA) as the functional monomer, and ethylene glycol dimethacrylate (EGDMA = 2‐methylprop‐2‐enoic acid ethane‐1,2‐diyl ester) as the cross‐linking agent. The adsorption property of the imprinted polymers was studied by UV spectrophotometry and HPLC. The results indicated that the porogen solvent had a certain influence on the adsorption performance of the polymer. The vanillin‐imprinted polymer MIP₁ prepared with MeOH as porogen, exhibited advantageous characteristics, i.e., a high binding activity, a good selectivity, and a rapid adsorption equilibrium. The binding parameters studied by Scatchard analysis established that there are two types of binding sites in MIP₁. Finally, by packing an SPE column (SPE = solid‐phase extraction) with the polymer MIP₁, the vanillin was separated and enriched successfully by this sorbent from the samples of Vanilla fragrans and beer.     

Synthesis of molecularly imprinted polymer adsorbents for solid‐phase extraction of strobilurin fungicides from agricultural products

Molecularly imprinted polymers for strobilurin fungicides were prepared by precipitation polymerization employing azoxystrobin as template molecular together with methacrylic acid monomer and trimethylolpropane triacrylate cross‐linker. Morphological characterization showed molecularly imprinted polymers were uniform spherical particles with about 0.2 μm in diameter, while the morphologies of nonimprinted polymers were irregular bulk. The equilibrium binding and selective experiments proved that molecularly imprinted polymers possessed a higher affinity toward four fungicides compared to nonimprinted polymers and heterogeneous binding sites were found in the molecularly imprinted polymers. Molecularly imprinted solid‐phase extraction conditions, including sample loading solvents, selective washing, and elution solvents, were carefully optimized. The developed method showed good recoveries (70.0–114.0%) with relative standard deviations in range of 1.0–9.8% (n  =  3) for samples (cucumber and peach) spiked at three different levels (10, 50, and 100 μg/ kg). The detection limit (signal/noise = 3) ranged from 0.01 to 0.08 μg/kg. The results demonstrated good potential use of this convenient and highly efficient method for determining trace strobilurin fungicides in agricultural products.     

An Artificial Estrogen Receptor through Combinatorial Imprinting

Polymeric sorbents targeting endocrine‐disrupting estrogen active compounds (EAC) were prepared by terpolymer imprinting using 17β‐estradiol (E2) as template. From a group of eight functional monomers representing Brønsted acids, bases, hydrogen‐bond donors and acceptors, as well as π‐interacting monomers, a terpolymer library that comprises all possible binary combinations of the functional monomers was prepared. Binding tests revealed that imprinted polymers exhibit a markedly higher affinity for E2 compared to nonimprinted polymers (NIPs) or polymers prepared by using single functional monomers. A combination of methacrylic acid (MAA) and p‐vinylbenzoic acid offered a particularly promising lead polymer, displaying an imprinting factor of 17 versus 2.4 for a benchmark polymer prepared by using only MAA as functional monomer. The saturation capacities ascribed to imprinted sites were four to five times higher for this polymer compared to previously reported imprinted polymers. NMR titrations and molecular dynamics simulations corroborated these results, indicating an orthogonal preference of the two functional monomers with respect to the E2 3‐OH and 17‐OH groups. The optimized polymer exhibited a retentivity for EACs that correlates with their inhibitory effect on the natural receptor. By using the optimized molecularly imprinted polymers (MIPs) in a model water‐purification system, they were capable of completely removing ppb levels of a small group of EACs from water. This is in contrast to the performance of nonimprinted polymers and well‐established sorbents for water purification (e.g., active carbon), which still contained detectable amounts of the compounds after treatment.     

Role of molecularly imprinted polymers for selective determination of environmental pollutants--a review

The molecularly imprinted polymers (MIPs) are synthetic polymers possessing specific cavities designed for a target molecule. By a mechanism of molecular recognition, the MIPs are used as selective tools for the development of various analytical techniques such as liquid chromatography, capillary electrochromatography, solid-phase extraction (SPE), binding assays and biosensors. This review describes the application of MIPs to the determination of environmental pollutants in these different analytical approaches with a special emphasis on their potential as selective SPE sorbent for the selective extraction of target analytes from complex matrices.     

Molecularly imprinted polymers on the surface of silica microspheres via sol‐gel method for the selective extraction of streptomycin in aqueous samples

Streptomycin‐imprinted silica microspheres were prepared by combining a surface molecular‐imprinting technique with the sol‐gel method. A mixture of tetrahydrofuran, ethanol, and water (6:1:1, v/v/v) was selected as dispersing solvent while 3‐aminopropyltriethoxysilane and triethoxyphenylsilane acted as functional monomers, and tetraethyl orthosilicate as a cross‐linker. Characterization of the molecularly imprinted polymers was conducted using scanning electron microscope and dynamic binding experiments. As compared to the nonimprinted polymers, the imprinted polymers exhibited a higher degree of saturated adsorption volume up to 26.3 mg/g, and better selectivity even in an aqueous solution with interfering compounds, including dihydrostreptomycin, neomycin, and tetracycline. The adsorption ability and selectivity were observed to be influenced by the mole ratio of 3‐aminopropyltriethoxysilane and triethoxyphenylsilane. Feasibility of the polymers to be used for actual application was also evaluated with spiked samples, indicating great potential for large‐scale applications. Moreover, the streptomycin‐imprinted polymers can be repeatedly used for 12 cycles without losing original performance, which is beneficial for commercial use.     

Variable selection in near-infrared spectroscopy: benchmarking of feature selection methods on biodiesel data

In the present work, microwave heating initiated precipitation polymerization was developed to prepare podophyllotoxin (PPT) molecularly imprinted polymers (MIPs), resulting in much shorter polymerization time and better particle morphology. Prior to the polymerization, ultraviolet and FTIR spectroscopy were used to study the interactions between PPT and the functional monomers. The synthesized parameters were respectively optimized and the optimal conditions for the efficient adsorption property were template: PPT, 1 mmol; functional monomer: acrylamide, 6 mmol; bi-crosslinker: ethylene glycol dimethacrylate, 20 mmol and divinylbenzene, 20 mmol; porogen: acetonitrile, 40 mL; initiator: azobisisobutyronitrile, 0.01mol L?1; polymerization temperature: 60°C. FTIR spectroscopy, SEM and thermal analysis were used to characterize the MIPs. The results of the equilibrium rebinding experiments and the competitive adsorption experiments showed that these imprinted polymers exhibited good adsorption ability for the PPT. Scatchard analysis illustrated that two and one types of binding sites were generated in the MIPs and non-imprinted polymers (NIPs), respectively. Using the prepared MIPs as the solid phase extraction (SPE) sorbent, PPT was extracted selectively and efficiently from Dysosma versipellis, Sinopodophyllum hexandrum and Diphylleia sinensis. The regression equation was y=5.873×10?x+17075.659 with the correlation coefficient of 0.9994 in the concentration range of 0.005-0.4 mg mL?1. After washing and eluting the SPE column with methanol and MeOH/acetic acid solution (v/v, 9:1), the limits of detection were 0.12-0.18 μg mL?1 and their recoveries were in the range of 89.5-91.1% with all RSDs lower than 3.7.     

Determination of fusaric acid in maize using molecularly imprinted SPE clean‐up

A new LC method to detect fusaric acid (FA) in maize is reported based on a molecularly imprinted SPE clean‐up using mimic‐templated molecularly imprinted polymers. Picolinic acid was used as a toxin analog for imprinting polymers during a thermolytic synthesis. Both acidic and basic functional monomers were predicted to have favorable binding interactions by MP2 ab initio calculations. Imprinted polymers synthesized with methacrylic acid or 2‐dimethylaminoethyl methacrylate exhibited imprinting effects in SPE analysis. FA levels were determined using RP ion‐pairing chromatography with diode‐array UV detection and tetrabutylammonium hydrogen sulfate in the mobile phase. A method was developed to detect FA in maize using molecularly imprinted SPE analysis within the range of 1–100 μg/g with recoveries between 83.9 and 92.1%.     

Determination of Chlorogenic Acid and Rutinum in Herba Artemisiae Scopariae with Multitemplate Molecularly Imprinted Polymers for Solid-phase Extraction with High-performance Liquid Chromatography

Novel multitemplate molecularly imprinted polymers were prepared using mixtures of chlorogenic acid and rutinum as molecular templates, acrylamide as a functional monomer, divinylbenzene as the cross-linker, and 20:80 methanol:acetone as the porogen. The polymers were assessed for solid-phase extraction (SPE) for the purification of two compounds from Herba Artemisiae Scopariae. The synthesized molecularly imprinted polymers were identified by infrared spectroscopy and scanning electron microscopy. Systematic characterization of the functional monomer and porogens on the recognition properties of the molecularly imprinted polymers were carried out. Comparison with single-template molecularly imprinted polymers showed that the multitemplate molecular polymers exhibited higher selectivity and adsorption capacity for multiple analytes. The optimization of washing solvent as 1:9 acetone:water and the elution solvent as 9:1 acetonitrile:acetic acid provided a reliable analytical method with strong recognition toward multiple analytes in Herba Artemisiae Scopariae extracts with satisfactory recoveries of 89.6% for chlorogenic acid and 93.8% for rutinum. These results demonstrate that the multitemplate molecularly imprinted polymers coupled with SPE are effective for the selective purification of bioactive compounds in complex samples.     

Molecularly imprinted polymers for bisphenol A for HPLC and SPE from water and milk

Molecularly imprinted polymers (MIPs) for bisphenol A (BPA) were prepared by two synthetic routes: semi-covalent and noncovalent methodology. The molecular imprinting effect was evaluated using the polymers in HPLC and SPE. Polymers prepared with noncovalent mode were proven more effective. These polymers were applied in SPE facilitating selective retention of BPA from bottled water and milk. The developed sample preparation was simple and efficient comprising only dilution of milk and MISPE prior to LC-MS analysis. Overall MISPE enhanced sample clean-up. Compared with control nonimprinted polymers and conventional C18 SPE cartridges, the MIPs exhibited selective analyte recognition. The method provided quantitative BPA recoveries, very good reproducibility (% RSDs lower than 7%), and low LOD (0.2 ng/g). MIP interacts similarly with deuterated BPA allowing its use as internal standard in LC-MS. The most critical parameters of MISPE were the organic content in loading-washing medium and the washing volume. Low flow rates in the elution step enhanced extraction recovery. Important advantages of the MIP were: the high breakthrough volumes (> 500 mL of water), high mass capacity (> 10 ng/mg of MIP sorbent), good linearity, and good stability in performance for over 35 cycles of use.     

Preparation and characterization of molecularly imprinted polymers based on β‐cyclodextrin‐stabilized Pickering emulsion polymerization for selective recognition of erythromycin from river water and milk

Molecularly imprinted polymers were prepared via β‐cyclodextrin‐stabilized oil‐in‐water Pickering emulsion polymerization for selective recognition and adsorption of erythromycin. The synthesized molecularly imprinted polymers were spherical in shape, with diameters ranging from 20 to 40 µm. The molecularly imprinted polymers showed high adsorption capacity (87.08 mg/g) and adsorption isotherm data fitted well with Langmuir model. Adsorption kinetics study demonstrated that the molecularly imprinted polymers acted in a fast adsorption kinetic pattern and the adsorption features of molecularly imprinted polymers followed a pseudo‐first‐order model. Adsorption selectivity analysis revealed that molecularly imprinted polymers had a much better specificity for erythromycin than that for spiramycin or amoxicillin, and the relative selectivity coefficient values on the bases of spiramycin and amoxicillin were 3.97 and 3.86, respectively. The Molecularly imprinted polymers also showed a satisfactory reusability after four times of regeneration. In addition, molecularly imprinted polymers exhibited good adsorption capacities for erythromycin under complicated environment, that is, river water and milk. These results proved that the as‐prepared molecularly imprinted polymers is a potent absorbent for selective recognition of erythromycin, and therefore it may be a promising candidate for practical applications, such as wastewater treatment and detection of erythromycin residues in food.     

Preparation of hydrophilic molecularly imprinted polymers for tetracycline antibiotics recognition

Hydrophilic molecularly imprinted polymers(MIPs) were prepared using tetracycline as template,methacrylic acid as monomer and glycidilmethacrylate as pro-hydrophilic co-monomer.Compared with common MIPs,the imprinting effect and adsorption amounts of hydrophilic MIPs for tetracycline(TC) were greatly improved in water media.Furthermore,the electrochemical sensor fabricated by modifying hydrophilic MIPs on glassy carbon electrode was developed for the determination of TC in foodstuff samples.