Thermo- and pH-responsive polypropylene microporous membrane prepared by the photoinduced RAFT-mediated graft copolymerization

Thermo- and pH-responsive polypropylene microporous membrane prepared by photoinduced reversible addition–fragmentation chain transfer (RAFT) graft copolymerization of acrylic acid and N-isopropyl acrylamide by using dibenzyltrithiocarbonate as a RAFT agent. Attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR), X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscopy (FE-SEM) were used to characterize the structural and morphological changes on the membrane surface. Results of ATR/FT-IR and XPS clearly indicated that poly(acrylic acid) (PAAc) and poly(N-isopropyl acrylamide) (PNIPAAm) were successfully grafted onto the membrane surface. The grafting chain length of PAAc on the membrane surface increased with the increase of UV irradiation time, and decreased with the increase of the concentration of chain transfer agent. The PAAc grafted membranes containing macro-chain transfer agents, or the living membrane surfaces were further functionalized via surface-initiated block copolymerization with N-isopropyl acrylamide in the presence of free radical initiator, 2,2′-azobisisobutyronitrile. It was found that PNIPAAm can be grafted onto the PAAc grafted membrane surface. The results demonstrated that polymerization of AAc and NIPAAm by the RAFT method could be accomplished under UV irradiation and the process possessing the living character. The PPMMs with PAAc and PNIPAAm grafting chains exhibited both pH- and temperature-dependent permeability to aqueous media.     

Functional and surface-active membranes from poly(vinylidene fluoride)-graft-poly(acrylic acid) prepared via RAFT-mediated graft copolymerization

Poly (vinylidene fluoride) (PVDF) with "living" poly (acrylic acid) (PAAc) side chains (PVDF-g-PAAc) was prepared by reversible addition-fragmentation chain transfer (RAFT)-mediated graft copolymerization of acrylic acid (AAc) with the ozone-pretreated PVDF. The chemical composition and structure of the copolymers were characterized by elemental analysis, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The copolymer could be readily cast into pH-sensitive microfiltration (MF) membranes with enriched living PAAc graft chains on the surface (including the pore surfaces) by phase inversion in an aqueous medium. The surface composition of the membranes was determined by X-ray photoelectron spectroscopy. The morphology of the membranes was characterized by scanning electron microscopy. The pore size distribution of the membranes was found to be much more uniform than that of the corresponding membranes cast from PVDF-g-PAAc prepared by the "conventional" free-radical graft copolymerization process. Most important of all, the MF membranes with surface-tethered PAAc macro chain transfer agents, or the living membrane surfaces, could be further functionalized via surface-initiated block copolymerization with N-isopropylacrylamide (NIPAAM) to obtain the PVDF-g-PAAc-b-PNIPAAM MF membranes, which exhibited both pH- and temperature-dependent permeability to aqueous media.     

Graft copolymerization kinetics of acrylic acid onto the poly(ethylene terephthalate) surface by atmospheric pressure plasma inducement

After one atmospheric pressure plasma treatment of poly(ethylene terephthalate) (PET) film, acrylic acid (AAc) in aqueous solution was successfully graft‐copolymerized onto PET films. The effects of reaction time, AAc monomer concentration and reaction temperature on grafting behavior of AAc were systematically studied. Possible reaction kinetics of plasma‐induced graft copolymerization, starting from initial hydroperoxide decomposition, were proposed. Through the Arrhenius analysis about graft copolymerization kinetics of AAc monomers on PET surface, it was revealed that the activation energies of decomposition, propagation and termination were 98.4, 63.5, and 17.5 kJ/mol, respectively. The temperature around 80 °C was favorable not only for the formation of oxide radicals through the thermal decomposition of hydroperoxide on PET surface but also for the extension of graft copolymer chain through direct polymer grafting. Poly(acrylic acid) (PAAc) grains grafted onto PET surfaces possessed relatively uniform size and both PAAc grain size and surface roughness increased with increasing the grafting degree of AAc. The increase of grain size with increasing grafting degree results from the possibility of forming long chain graft copolymers and their shielding of reactive sites. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1594–1601, 2008     

Effect of the pore surface modification of an inorganic substrate on the plasma‐grafting behavior of pore‐filling‐type organic/inorganic composite membranes

We have investigated the effect of the surface state and surface treatment of the pores of an inorganic substrate on the plasma‐grafting behavior of pore‐filling‐type organic/inorganic composite membranes. Shirasu porous glass (SPG) was used as the inorganic substrate, and methyl acrylate was used as the grafting monomer. The grafting rate increased as the density of silanol on the SPG substrate increased. This result suggests that radicals are generated mainly at the silanol groups on the pore surface by plasma irradiation. The SPG substrates were treated with silane coupling agents used to control the mass of organic material bonded to the pore surface. The thickness of the grafted layer became thinner as the mass of organic material bonded to the pore surface of SPG increased. This decrease in the thickness of the grafted layer could be explained by the decrease in the penetration depth of vacuum ultraviolet rays contained in plasma having a wavelength of less than 160 nm that generated radicals in the pores of the substrate. The thickness of the grafted layer inside the SPG substrates could be controlled through the control of the mass of organic material bonded to the pore surface of the SPG substrate. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 846–856, 2006     

Synthesis and Characterization of pH‐sensitive Poly(IA‐co‐AAc‐co‐AAm) Hydrogels via Frontal Polymerization

In this work, we report a series of poly(itaconic acid‐co‐acrylic acid‐co‐acrylamide) (poly(IA‐co‐AAc‐co‐AAm)) hydrogels via frontal polymerization (FP). FP starts on the top of the reaction mixture with aid of heating provided from soldering iron gun. Once polymerization initiated, no further energy is required to complete the process. The influences of IA/AAc weight ratios on frontal velocities, temperatures, and conversions on the reaction time are thoroughly investigated and discussed where the amount of AAm monomer remains constant. Fourier transform‐infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), scanning electron microscope (SEM), dynamic mechanical analysis, and the swelling measurement are applied to characterize the as‐synthesized poly(IA‐co‐AAc‐co‐AAm) hydrogels. Interestingly, the swelling ratios of the hydrogels are changed with different IA/AAc contents, and the maximum swelling ratios are ~4439% in water. SEM images describe highly porous morphologies and explain good swelling capabilities. Moreover, the poly(IA‐co‐AAc‐co‐AAm) hydrogels exhibit superior pH‐responsive ability. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2214–2221     

Signal‐responsive gating of porous membranes by polymer brushes

Various types of signal‐responsive polymers were grafted on surfaces of porous membranes as polymer brushes. The grafted polymers shrank and extended in response to environmental signals, such as pH, ionic strength, temperature, redox reaction and photo‐irradiation. The pore size was regulated by the extent of the polymer brush. The phenomenon was observed in situ by atomic force microscopy. As a result, the substance permeation through the porous membrane was controlled in response to the signals. The permeation control was rapid in comparison with hygrogel‐type membranes, and was reversibly performed. Copyright © 2000 John Wiley & Sons, Ltd.     

Preparation of dual stimuli‐responsive PET track‐etched membrane by grafting copolymer using ATRP

A dual stimuli‐responsive (pH and thermo) polyethylene terephthalate (PET) track‐etched membrane has been prepared using atom transfer radical polymerization (ATRP). First, ATRP initiator 2‐bromoisobutyryl bromide was anchored onto the membrane surface. Then, 2‐hydroxyethyl‐methacrylate (HEMA) and N‐isopropylacrylamide (NIPAAm) were grafted onto the membrane surface using ATRP. X‐ray photoelectron spectroscopy, ATR‐Fourier transform infrared spectroscopy, scanning electron microscopy and thermogravimetric analysis were used to characterize the membrane structure and thermal properties; water flux measurement was used to investigate the double stimuli‐responsive property of the obtained membrane. The results indicate that the PHEMA and PNIPAAm binary grafted PET track‐etched membrane has double environmental responsiveness. This method provides a potential modification method for preparing functional membranes. Copyright © 2012 John Wiley & Sons, Ltd.     

Microfiltration membranes prepared from polyethersulfone powder grafted with acrylic acid by simultaneous irradiation and their pH dependence

Polyethersulfone (PES) powder was grafted with acrylic acid (AAc) by simultaneous γ-ray irradiation. The kinetics of the radiation induced graft polymerization was studied and the grafted PES powder was characterized. Then, microfiltration (MF) membranes were prepared from PES-g-PAAc powder with different degrees of grafting (DG) under phase inversion method. The swelling behavior and the mean pore size of MF membranes were measured, and the filtration property was tested. The results showed that the pore size and the flux of MF membranes increased with the increase in DG. And, MF membranes’ properties were dependent on the pH value.     

Excellent anti‐bacterial activity and surface properties of polyamide‐6 films modified with argon‐plasma and methyl diallyl ammonium salt‐graft

In this study, the effect of argon‐plasma treatment on the grafting of methyl diallyl ammonium salt (MDAA) onto polyamide‐6 film and the anti‐bacterial and surface properties of the plasma‐ and graft‐treated film were investigated. The grafting amounts of MDAA caused by argon‐plasma treatment increased with the increase in the plasma exposure time and plasma power. The analyses of Fourier transform infrared (FT‐IR) spectroscopy and electron spectroscopy for chemical analysis (ESCA) spectra revealed that the epoxy and vinyl groups of MDAA could be grafted on the argon‐plasma treated polyamide‐6 film. The survey spectra of ESCA, the patterns of atomic force microscopy (AFM), and the spectra from scanning electron microscopy (SEM) were employed to certify the surface modification of argon‐plasma treated and the argon‐plasma treated/MDAA grafted polyamide‐6 films. Argon‐plasma treatment could generate the functional group and increase the roughness on the surface of polyamide‐6 film. This phenomenon could enhance the grafting effect of MDAA. The anti‐bacterial property of argon‐plasma treated/MDAA grafted polyamide‐6 film was excellent. This argon‐plasma treated/MDAA grafted polyamide‐6 film was expected to be applied on the field of packing. Copyright © 2008 John Wiley & Sons, Ltd.     

Pore‐filling electrolyte membranes based on microporous polyethylene matrices activated with plasma and sulfonated hydrogenated styrene butadiene block copolymer. Synthesis,microstructural and electrical characterization

In this research a series of pore‐filling electrolyte membranes were prepared, based on a sulfonated and hydrogenated styrene/butadiene block copolymer (SHSBS) and plasma‐treated microporous polyethylene (PE) membranes. The pore‐filling electrolyte membranes were characterized by means of scanning electronic microscopy (SEM), infrared spectroscopy (FTIR‐ATR), and dynamic mechanical analysis (DMA). In addition, the water uptake and methanol/water uptake capacities of these membranes were determined using several methanol in water solutions, as well as the permeability coefficients, for both water and methanol, using a 2 M methanol in water solution and pure methanol. Finally, electrical behavior was recorded by means of electrochemical impedance spectroscopy (EIS) and the four probe technique (FPT). The SEM images recorded show good coating of the pore‐filling electrolyte membranes on the plasma‐treated PE matrices, and DMA shows the proper relaxations of the two components: PE and SHSBS. Furthermore, the methanol/water absorption capacity was observed to diminish with plasma treatment of the matrix. Methanol permeability of the pore‐filling electrolyte membranes is notably lower than that of the Nafion® membrane, ion conductivity moving in the order of 10⁻² S cm⁻¹. Both of these characteristics qualify the experimental membranes as candidates to be applied as proton exchangers in fuel cells (FCs). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1684–1695, 2008     

Conducting polymer films fabricated by oxidative graft copolymerization of aniline on poly(acrylic acid) grafted poly(ethylene terephthalate) surfaces

A conductive polyaniline/poly(ethylene terephthalate) (PANI/PET) composite film was fabricated via the oxidative graft copolymerization of aniline (ANI) onto the plasma-induced poly(acrylic acid) (PAAc) grafted PET surface. The attenuated total reflectance Fourier transform infrared spectroscopy spectra (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS) results confirmed that PANI was successfully grafted onto the surface of the PAAc-g-PET films. The effects of the experimental conditions on the percentage of PANI grafted onto the PAAc-g-PET films were extensively investigated. A very high grafting percentage of ANI can be obtained through the acid-base reaction between the aniline monomer and PAAc on the PAAc-g-PET surface at high temperature. As a result, the grafting percentage of PANI can be increased to as high as 12.18 wt %, which causes the surface resistance of the PANI-g-PAAc-g-PET film to be reduced to about 1000 Omega/sq. We predicted that this is because of the high flexibility of the PAAc molecular chains and high solubility of aniline, both of which facilitate the binding of aniline to PAAc during this high temperature acid-base reaction. It was observed by atomic force microscopy (AFM) that the PANI-modified PET surface exhibits higher size irregularity and surface roughness, which further indicated that a much greater number of aniline molecules can be reactively bonded to and distributed along the grafted AAc chains and that the PANI-g-PAAc-g-PET surface resulting from the sequential oxidative graft copolymerization can possess higher electrical conductivity.     

Swelling kinetics of poly(aspartic acid)/poly(acrylic acid) semi‐interpenetrating polymer network hydrogels in urea solutions

Semi‐interpenetrating network (semi‐IPN) hydrogels, composed of poly(aspartic acid) (PAsp) and poly(acrylic acid) (PAAc) with various ratios of PAsp to AAc, were prepared. In this work, swelling kinetics was investigated through calculating some parameters. The swelling ratios were measured at room temperature, using urea solutions as liquids to be absorbed. Compared to in deionized water, the hydrogels showed larger swelling ratios in urea solutions, which might be attributed to the chemical composition of urea. The equilibrium swelling ratio could achieve 600 g/g, and the equilibrium urea/water contents were more than 0.99. The diffusion exponents were between 0.5 and 0.7, suggesting that the solvent transport into the hydrogel was dominated by both diffusion and relaxation controlled systems. Therefore, the PAsp/PAAc semi‐IPN hydrogels were appropriate to carry substances in a urea/water environment for pharmaceutical, agricultural, environmental, and biomedical applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 666–671, 2010     

Gamma radiation synthesis of comb-type graft hydrogels based on poly(acrylic acid) and 4-vinylpyridine

A pH-sensitive comb-type hydrogel was obtained by gamma radiation polymerization and crosslinking of acrylic acid (AAc) in solution. The pH-sensitive 4-vinylpyridine (4VP) was then grafted to the poly acrylic acid (PAAc) hydrogel using gamma radiation from a ⁶⁰Co source. The comb type graft polymers obtained (net-PAAc)-g-4VP has been studied through determination of graft yield and swelling behavior. The critical pH value was found to be 5.6. The apparent mechanical properties appear to be qualitatively better than hydrogels of PAAc upon swelling. The new comb-type system presents faster swelling response (30 h) than the polyacrylic acid hydrogel (50 h). The increase in dose rate from 7.3 to 11.3 kGy h⁻¹, increase the radiation grafting percentage of 4VP in the system. Comb-type polymers were also characterized by DSC, TGA and FTIR-ATR.     

Preparation and Characterization of pH-sensitive Hydrogel Film of Chitosan/Poly(acrylic acid) Copolymer

A hydrogel film of chitosan/poly(acrylic acid) (CS/PAAc) copolymer with the property of pH sensitivity, was prepared by irradiating the chitosan film, which was then swelled by aqueous AAc solutions of different concentrations. The effects of the feed ratio of chitosan and AAc on the properties of the hydrogels, such as swelling ratio and pH-sensitivity, were determined. Fourier transform infrared (FT-IR) spectroscopy was applied in the attenuated total reflectance (ATR) mode for analyzing the structure change of the hydrogels after the treatment in buffer solutions of different pHs.     

Surface Functionalization of Fe3O4 Magnetic Nanoparticles via RAFT‐Mediated Graft Polymerization

Summary: Surface functionalization of Fe₃O₄ magnetic nanoparticles (MNP) via living radical graft polymerization with styrene and acrylic acid (AAc) in the reversible addition‐fragmentation chain transfer (RAFT)‐mediated process was reported. Peroxides and hydroperoxides generated on the surface of Fe₃O₄ nanoparticles via ozone pretreatment facilitated the thermally initiated graft polymerization in the RAFT‐mediated process. A comparison of the MNP before and after the RAFT‐mediated process was carried out using transmission electron microscopy (TEM) analysis, Fourier transform infrared (FTIR), and X‐ray photoelectron spectroscopy (XPS). Gel permeation chromatography (GPC) was used to determine the molecular weight of the free homopolymer in the reaction mixture. Well‐defined polymer chains were grown from the MNP surfaces to yield particles with a Fe₃O₄ core and a polymer outer layer. The resulting core–shell Fe₃O₄‐g‐polystyrene and Fe₃O₄‐g‐poly(acrylic acid) (PAAc) nanoparticles formed stable dispersions in the organic solvents for polystyrene (PS) and PAAc, respectively.

Schematic illustration of thermally induced graft polymerization of styrene and AAc with the ozone‐treated Fe₃O₄ MNP.     

Preparation and characterization of novel PES‐(SiO2‐g‐PMAA) membranes with antifouling and hydrophilic properties for separation of oil‐in‐water emulsions

In the present study, modification of nanoparticles (NPs) was investigated to mitigate aggregation of SiO₂ nanoparticles and improve the polymeric membrane's performance. For this purpose, the surface of SiO₂ nanoparticles was activated with amine groups, and polymethacrylic acid (PMAA) was grafted on the surface of NPs by atom transfer radical polymerization. Modified NPs were characterized by Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) tests. Polyethersulfone (PES) membranes were fabricated with both SiO₂ and SiO₂‐g‐PMAA NPs via nonsolvent‐induced phase separation method. The fabricated membranes were characterized regarding their permeability, hydrophilicity, and porosity properties, and their separation efficiency was tested using the synthetic oil‐in‐water emulsion. The surface and cross‐sectional morphologies of membranes were observed by field emission scanning electron microscopy (FESEM). The experimental trials showed that modified NPs dispersed more uniformly in the structure of membranes and hydroxyl groups on the surface of NPs acted more effectively. Modification of NPs enhance the membrane performance in terms of permeate flux, hydrophilicity, and porosity. NPs modification improved the permeate flux about 46%. Oil rejection for all tested membranes was more than 98%, and modification of NPs did not reduce the rejection of membranes. The optimum concentration was obtained as 1 wt.% and 1.5 wt.% for SiO₂ and SiO₂‐g‐PMAA, respectively. Aggregation effect dominated at concentrations beyond the optimum values that decreased the permeate flux, consequently.     

Novel comb-type hydrogels of net-[PP-g-AAc]-g-4VP synthesized by gamma radiation,with possible application on Cu2+ immobilization

A novel comb-type grafted hydrogel system of net-[PP-g-AAc]-g-4VP was synthesized by gamma radiation in three steps. In the first step a pH sensitive graft copolymer of AAc onto PP film was obtained by radiation grafting of acrylic acid (AAc) onto polypropylene (PP) films in aqueous solution at radiation doses of 10 kGy with a ⁶⁰Co source. The grafted side chains of poly (acrylic acid) (PAAc) were then cross-linked with gamma radiation at different radiation doses to give net-[PP-g-AAc]. Finally, 4-vinylpyridine (4VP) was grafted into the net-[PP-g-AAc]. The comb-type grafted hydrogel obtained, net-[PP-g-AAc]-g-4VP, has been studied through determination of graft yield and swelling behavior at room temperature. Two critical pH values were found for net-[PP-g-AAc]-g-4VP at 4.5 and 7.2. Initial studies on the immobilization of Cu²⁺ ions from solution into net-[PP-g-AAc]-g-4VP films were performed.The comb-type grafted hydrogel, grafted onto PP was also characterized by differential scanning calorimetry (DSC), scanning electronic microscopy (SEM) and FTIR-ATR.     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

Grafting of regenerated cellulose membrane by surface‐initiated atom transfer radical polymerization and its pH‐resposive behavior

Regenerated cellulose (RC) membranes which have pH modulated permeability have been prepared by anchoring the hydroxyl groups on the membrane surface with 2‐bromoisobutyryl bromide, followed by grafting with acrylic acid (AA) using atom transfer radical polymerization (ATRP). The obtained membranes were analyzed by X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared attenuated total reflection spectrometer (ATR‐FTIR), scanning electron microscopy (SEM), TGA and the results showed that AA had been grafted onto the membrane surfaces successfully. Then the pH modulated permeability properties were tested by water flux measurement. All results show that the pH modulated permeability properties of a RC membrane can be obtained by surface‐initiated ATRP. Copyright © 2010 John Wiley & Sons, Ltd.