Li4SiO4-Li3VO4赝二元系和Li4GeO4-Li4SiO4-Li3VO4赝三元系中新的锂离子导体

本文在室温到300℃的温度范围内研究了Li₄SiO₄-Li₃VO₄和Li₄GeO₄-Li₄SiO₄-Li₃VO₄体系中的离子导电性,发现γ_II相固溶体Li_3+xV_1-xSi_xO₄是好的锂离子导体。所研究的成分中Li_3.3V_0.7Si_0.3O₄的离子电导率最高,室温下为1×10^-5Ω^-1·cm^-1,在42—192℃的电导激活能为0.36eV,电子电导率可以忽略,因而这是迄今所发现的最好的锂离子导体之一。粗略确定了Li₄GeO₄-Li₄SiO₄-Li₃VO₄三元系中电导率高的范围,发现在Li_3.5V_0.5Ge_0.5O₄中Si部分取代Ge可以使电导率进一步提高,Li_3.5V_0.5Ge_0.4Si_0.1O₄的室温电导率可达1.3×10^-5Ω^-1·cm^-1,电导激活能为0.40eV。 关键词：     

Li+ ion conducting γ solid solutions in the systems Li4XO4-Li3YO4: X=Si,Ge, Ti; Y=P,As, V; Li4XO4-LiZO2: Z=Al,Ga, Cr and Li4GeO4-Li2CaGeO4

A wide variety of solid solutions with a structure related to that of γ Li₃PO₄ may be prepared. These include materials such as lisicon, Li_2+2xZn_1-xGeO₄ and the title systems, many of which have not been studied previously. Conductivity data are presented for eight systems: Li₄GeO₄-Li₃(P, As, V)O₄; Li₄TiO₄-Li₃(As, V)O₄; Li₄GeO₄-Li(Ga, Al)O₂; Li₄GeO₄-Li₂CaGeO₄ and the results compared with those reported in the literature for Li₄SiO₄-Li₃(P, As, V)O₄ systems and lisicon. dc polarisation measurements were made on four of the system and it was found that the electronic transference number is 10^?4 or less. The materials with the highest conductivity were found in the systems, Li₄ (Ge, Ti) O₄-Li₃ (As, V)O₄ with σ ~ (3 to 4) × 10^?5 Ω^?1 cm^?1 at room temperature. It is noted that the systems with the highest conductivity are generally those with the largest unit cell volume.     

The determination of Li+ mobility in solid electrolyte Li1.3Al0.1Zn0.1Ti1.8P3O12 in view of ionic diffusivity and conductivity

Nasicon-type solid electrolyte Li_1.3Al_0.1Zn_0.1Ti_1.8P₃O₁₂ was prepared by citric acid-assisted acrylamide polymerisation gel method. X-ray diffraction pattern showed that the introduction of Zn²⁺ in the parent matrix Li_1+x Al _x Ti_2?x P₃O₁₂ made it easier to get high-purity rhombohedral structure (space group $ R\overline 3 C $ ) Li_1.3Al_0.1Zn_0.1Ti_1.8P₃O₁₂ without the evidence of impurity secondary phase. The Li⁺ kinetics were investigated by complex impedance in bulk pellet and ionic conductivity in battery-type composite cathode, respectively. Grain-interior resistance measured by galvanostatic intermittent titration technique, potential step chronoamperometry, and AC impedance spectroscopy at 20 °C varies in the range 1.2–1.95?×?10^?4?S?cm^?1, which is in good agreement with that obtained by complex impedance method 1.5?×?10^?4?S?cm^?1.     

Semiconducting properties of refractory oxides systems

Abstract

The electrical conductivity and thermoelectric power of pure and doped oxides system La₂O₃-Cr₂O₃-Al₂O₃ were investigated. Only single phase was observed in the compositions studied (20 atom fraction of aluminium).

The conductivity increases with increasing chromium content in the range of compositions studied, the values ranging from 10^?4 (ω-cm)^?1 to 1. 2 × 10^?1(ω-cm)^?1. In the case of samples doped with calcium (0. 01) the corresponding values range from 2 × 10^?1 (ω-cm)^?1 to 1. 67(ω-cm)^?1. The significance of the results has been discussed.     

Influence of nanocrystalline phases on the electrical properties of lithium titanate phosphate glass ceramics mixed with Ga2O3 nanocrystals

Several glass ceramic compositions dispersed with Ga₂O₃ nanocrystals, in the series samples (100???x)[0.4Li₂O–0.1TiO₂–0.5P₂O₅]?+?xGa₂O₃ with x?=?0, 2, 4, 6, 8, and 10?mol% of Ga₂O₃ were synthesized via high-energy ball milling technique and labeled as lithium gallium titanate phosphate glass (LTPG _x ) (x is the mol% of Ga₂O₃ nanocrystals). The compositions have been selected on the basis of thermal stability data obtained from differential thermal analysis. X-ray diffraction studies indicate nanocrystalline phase formation in the controlled crystallized glasses. The variation of electrical conductivity was explained in the light of growth of nanocrystalline phases. The best bulk conductivity (σ?=?7.03?×?10^?4?S?cm^?1, at 303?K) was achieved by the sample containing 8?mol% of Ga₂O₃ nanocrystals content, labeled as LTPG₈ sample. The activation energy for conduction (E_{a σ} ) is obtained from the temperature dependent of conductivity data, which is fitted to Arrhenius equation. The single super curve in the scaling spectra suggested the temperature-independent relaxation phenomenon.     

Ionic conductivity of substituted Li7TaO6 phases

Lithium ion conductivity in solid solutions of Li₇Ta_1-xNb_xO₆, Li₇Ta_1-xBi_xO₆, Li_7+xTa_1-xZr_xO₆ and Li_7-2xCa_xTaO₆ has been measured as a function of temperature and composition using the complex impedance method. At 200°C the conductivities of Li₇Ta_0.7Nb_0.3O₆, Li_7.4Ta_0.6Zr_0.4O₆ and Li_6.6Ca_0.2TaO₆ are 4.3 × 10^-4(ωcm)^-1, 3.0 × 10^-4(ωcm)^-1, 4.0 × 10^-4(ωcm)^-1 and 1.6 × 10^-4(ωcm)^-1 respectively. The results are discussed in relation to structural properties.     

Enhanced high-rate performance of sub-micro Li4Ti4.95Zn0.05O12 as anode material for lithium-ion batteries

Zn-doped Li₄Ti₅O₁₂ was prepared by a ball milling-assisted solid-state method, and the characters were determined by X-ray diffraction, Raman spectroscopy, scanning electron microscopy, cyclic voltammetry, and galvanostatic charge–discharge testing. The results show that Li₄Ti_5?x Zn _x O₁₂ (x?=?0, 0.05) exhibits the pure phase structure, and Zn doping does not change the electrochemical reaction process and basic spinel structure of Li₄Ti₅O₁₂. The particle size of both samples is about 300–500 nm. The prepared Li₄Ti_4.95Zn_0.05O₁₂ presents an excellent rate capability and capacity retention. At the charge–discharge rate of 1C, the initial discharge capacity of Li₄Ti_4.95Zn_0.05O₁₂ is 268 mAh g^?1. After 90 cycles at 5C, the discharge capacity of Li₄Ti_4.95Zn_0.05O₁₂ is obviously higher than that of Li₄Ti₅O₁₂. The excellent electrochemical performance of the Li₄Ti_4.95Zn_0.05O₁₂ electrode could be attributed to the improvement of reversibility by doping zinc and the sub-micro particle size.     

Preparation and electrical conductivity of LISICON thin films

LISICON thin films have been prepared with RF sputtering and subsequent heat-treatment. The crystal phases of sputtered films depend on the sputtering conditions, especially the target composition and ambient gas atmosphere. Though the as-sputtered films in Ar-O₂ mixed gas (target composition: Li₃Zn_0.5GeO₄+0.5 ZnO, gas pressure: 9×10^-2 Torr, oxygen gas content: 74.6%) were amorphous; LISICON single phase thin films were obtained after annealing at 600°C for 6 h. The conductivity of the film at 500°C is 5×10^-3ω^-1cm^-1 which is slightly lower than that for ceramic Li₃Zn_0.5GeO₄.     

Conductivite ionique des systemes Kx(Znx/2Ge1-x/2)O2 et Kx(GaxGe1-x)O2 de structure cristobalite

The crystal chemistry of the K_x(Zn_x/2Ge_{1-$\text{x}\text{2}$})O₂ and K_x(Ga_xGe_1-x)O₂ systems has been investigated. In each of them a solid solution with a cristobalite-type structure has been obtained with a 0.90?×?1 range. The K⁺ conductivity increases strongly with vacancy content, while the activation energy remains nearly constant.Influence of various crystal chemical parameters on the conductivity (lattice covalency, size of the bottlenecks, etc...) is discussed.     

Thermochemistry of the high and ambient temperature lithium vanadium bronze phases LixV2O5

The enthalpies of formation of a series of high and low temperature phases in the ternary oxide system Li_xV₂O₅ have been determined by solution calorimetry. Samples of the former, α-Li_0.04V₂O₅, β-Li_0.30V₂O₅, β'-Li_0.48V₂O₅ and γ-LiV₂O₅, were prepared by solid state reaction at 650°C. The ambient temperature materials Li_0.1V₂O₅(I), Li_0.45V₂O₅(II) and Li_1.03V₂O₅(III) were prepared by n-butyl lithiation in hexane. The thermochemistries of the two classes of material were examined and related to structural features and to the observed behaviour of V₂O₅ as a battery cathode material in lithium cells.     

Crystal structure analysis of Li<Subscript>3</Subscript>PO<Subscript>4</Subscript> powder prepared by wet chemical reaction and solid-state reaction by using X-ray diffraction (XRD)

Lithium phosphate (Li₃PO₄) is one of the promising solid electrolyte materials for lithium-ion battery because of its high ionic conductivity. A crystalline form of Li₃PO₄ had been prepared by two different methods. The first method was wet chemical reaction between LiOH and H₃PO₄, and the second method was solid-state reaction between Li₂O and P₂O₅. Crystal structure of Li₃PO₄ white powder had been investigated by using an X-ray diffraction (XRD) analysis. The results show that Li₃PO₄ prepared by wet chemical reaction belongs to orthorhombic unit cell of β-Li₃PO₄ with space group Pmn2₁. Meanwhile, Li₃PO₄ powder prepared by solid-state reaction belongs to orthorhombic unit cell of γ-Li₃PO₄ with space group Pmnb and another unknown phase of Li₄P₂O₇. The impurity of Li₄P₂O₇ was due to phase transformation in solid state reaction during quenching of molten mixture from high temperature. Ionic conductivity of Li₃PO₄ prepared by solid-state reaction was ～3.10^?7 S/cm, which was higher than Li₃PO₄ prepared by wet chemical reaction ～4.10^?8 S/cm. This increasing ionic conductivity may due to mixed crystal structures that increased Li-ion mobility in Li₃PO₄.     

New Li+ ion conductors in the system Li4SiO4−Li3AsO4

In the system Li₄SiO₄-Li₃AsO₄, Li₄SiO₄ forms a short range of solid solutions containing up to 14 to 20% Li₃AsO ₄, depending on temperature, and γ-Li₃AsO₄ forms a more extensive range of solid solutions containing up to ≈55% Li₄SiO₄. The Li₄SiO₄-Li₃AsO₄ phase diagram has been determined and is of binary eutectic character. The ac conductivity of polycrystalline samples was measured over the range 0 to at least 300°C for nine different compositions. The two solid solution series have much higher conductivity than the pure end-members; maximum conductivity was observed in the γ-Li₃AsO₄ solid solutions containing ≈40 to 55% Li₄SiO₄, with values of $\text{≈2×10}{}^{\mathrm{?6}}\text{Ω}{}^{\mathrm{?1}}\text{cm}{}^{\mathrm{?1}}$ at 20°C rising to ≈0.02 Ω^?1 cm^?1 at 300°C. These values are comparable to those found in the system Li₄SiO₄-Li₃PO₄. The variation with composition of the Arrhenius prefactor and activation energy has been interpreted in terms of the mechanisms of conduction. Li₃AsO₄ is a poor conductor essentially because the number of mobile Li⁺ ions is very small. This number, and hence the conductivity, increases dramatically on forming solid solutions with Li₄SiO₄, by the creation of interstitial Li⁺ ions. At ≈40 to 55% Li₄SiO₄, the number of mobile Li⁺ ions appears to be optimised. An explanation for the change in activation energy of conduction at ≈290°C in Li₄SiO₄ and at higher temperatures in Li₄SiO₄ solid solutions is given in terms of order-disorder of the Li⁺ ions.     

The ionic conductivity of Li6BaLa2M2O12 with coexisting Nb and Ta on the M sites

In a view to balancing cost and lithium ion conductivity, Li₆BaLa₂Nb _x Ta_2???x O₁₂ (x?=?0–2) was prepared by solid-state reaction, and its corresponding AC impedances were tested at temperatures ranging from 20 to 250 °C in air. Li₆BaLa₂Ta₂O₁₂ exhibits the highest conductivity, 8.77?×?10^?6?S/cm, and the second highest is Li₆BaLa₂Nb₂O₁₂ with 6.69?×?10^?6?S/cm. Partial replacement of Ta with Nb cannot bestow the advantages of cost saving or the enhancement of lithium ion conductivity. X-ray diffraction patterns revealed a gradual change as an increasing amount of Nb replaces Ta in Li₆BaLa₂Nb _x Ta_2???x O₁₂ (x?=?0–2), and it is thought that the trending of Nb and Ta to rest on the crystallographic planes is different.     

多晶Li3+xV1-xTxO4(T=Ge,Si)离子导电性能的改善

本文用阻抗谱方法研究了Li_3+xV_1-xT_xO₄(T=Si,Ge)多晶的离子导电性,发现一些工艺条件如成型压强、烧结时间和烧结程序对电导率有很大影响。注意分析了这些影响的物理起因。最佳工艺条件是:在大约8t/cm²压强下成型样品。在1000℃连续烧结5至6天,烧结过程中,应尽量避免温度波动。在此条件下制备的Li_3.5V_0.5Ge_0.5关键词：     

Conductivity and spectroscopic studies of Li<Subscript>2</Subscript>O-V<Subscript>2</Subscript>O<Subscript>5</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

Lithium vanadium-borate glasses with the composition of 0.3Li₂O–(0.7-x)B₂O₃–xV₂O₅ (x?=?0.3, 0.325, 0.35, 0.375, 0.4, 0.425, 0.45, and 0.475) were prepared by melt-quenching method. According to differential scanning calorimetry data, vanadium oxide acts as both glass former and glass modifier, since the thermal stability of glasses decreases with an increase in V₂O₅ concentration. Fourier transform infrared spectroscopy data show that the vibrations of [VO₄] structural units occur at V₂O₅ concentration of 45 mol%. It is established that the concentration of V⁴⁺ ions increases exponentially with the growth of vanadium oxide concentration. Direct and alternative current measurements are carried out to estimate the contribution both electronic and ionic conductivities to the value of total conductivity. It is shown that the electronic conductivity is predominant in the total one. The glass having the composition of 0.3Li₂O-0.275B₂O₃-0.475V₂O₅ shows the highest electrical conductivity that has the value of 7.4?×?10^?5 S cm^?1 at room temperature.     

Electrical properties of novel Li4.08Zn0.04Si0.96O4 ceramic electrolyte at high temperatures

Novel Li_4.08Zn_0.04Si_0.96O₄ electrolyte was synthesized by citric acid-assisted sol–gel method. The compound was studied by X-ray diffraction and complex impedance spectroscopy in the frequency range from 10 Hz to 10 MHz and temperature range from 573 to 773 K. The conductivity–frequency spectra exhibited two regions of conductivity dispersion related to Li⁺ ion transport in the bulk and grain boundaries. The activation energy of the bulk conductivity was found to be equal to the activation energy of relaxation frequency in the bulk. This indicated that the increase in conductivity with temperature was due to the increase in ion mobility while the number of charge carrier concentration was found to be constant with selected temperature range. The observation was in agreement with the calculated charge carrier concentration and ion mobility derived from conductance spectra, σ _ac(ω)?=?σ _o ?+?Aω ^α .     

Lithium ion conductivity of the B-site substitution in Li3xLa0.67−xRE y III Ti1−2yPyO3 system (REIII=Sc3+, Y3+, Nd3+, Sm3+, Eu3+, Yb3+)

The B-site substituted perovskite solid solution systems Li_3xLa_0.67−xRE_yTi_1−2yP_yO₃ (RE=Sc, Y, Nd, Sm, Eu, Yb) have been investigated. Perovskite solid solutions formed in the range of x=0.10, y<0.10 for RE=Sc³⁺, Y³⁺, Yb³⁺, x=0.10, y≤0.05 for RE=Nd³⁺, Sm³⁺, Eu³⁺. Li_0.3La_0.57Nd_0.05Ti_0.9P_0.05O₃ has the highest bulk conductivity of 4.31×10⁻⁴ S·cm⁻¹ and the highest total conductivity of 2.52×10⁻⁴ S·cm⁻¹ at room temperature in all prepared compositions. The compositions have low activation energies of about 24–30 kJ/mol in the temperature ranges of 298–523 K. SEM studies showed that the sample made by solid-state reaction has a sphere-like morphology and a rough particle with particle size of about 50 μm. The research results also indicated that the reaction temperature decreases and the electrochemical stabilities of the titanate-based perovskite-type solid solutions are improved by using RE³⁺ and P⁵⁺ replaced Ti⁴⁺ on B-site in the Li_3xLa_0.67−xTiO₃ parent.     

分散第二相γ-Al2O3对β-Li2SO4离子导电性的影响

本文研究了分散第二相γ-Al₂O₃对β-Li₂SO₄离子导电性的影响。β-Li₂SO₄(γ-Al₂O₃)的电导率随γ-Al₂O₃含量的增加而提高,到γ-Al₂O₃为50mol％时达到极大。当温度为253℃时,β-Li₂SO< 关键词：     

Li1+xGe2-xAlxP3O12系统的相关系和电导

本文研究了Li_1+xGe_2-xAl_xP₃O₁₂系统的相组成和电导的关系。发现用LiGe₂P₃O₁₂作为基体化合物,通过离子置换可以得到好的锂离子导体。用Al³⁺置换LiGe₂P₃O₁₂中的Ge⁴⁺,在0关键词：     

Li2Mo2-xWxO6多晶材料的结构、电学性能与导电机理的研究

本文采用还原气氛制备导电性能优良的多晶多相陶瓷材料Li₂Mo_2-xW_xO₆(x=0,0.1,0.3),采用粉末X射线衍射分析、特征X射线能谱分析、红外光谱分析和电子自旋共振波谱分析等现代测试手段,得到样品的物相结构为Li₂Mo_1-xW_xO₄和MoO₂两相组成。W的掺入主要取代Mo进入Li₂ 关键词：