Trapping phenomena in intrinsic hydrogenated amorphous silicon like materials studied using current transient spectroscopies

Transient spectroscopies such as time analyzed transients spectroscopy (TATS) provide powerful means of comparing density of states in new forms of amorphous like materials. These spectroscopies were utilized to study hydrogenated amorphous silicon (a-Si:H) and hydrogenated polymorphous silicon (pm-Si:H) grown at different pressures using PECVD. The results reveal marked differences between the two materials. In case of a-Si:H, as expected characteristic emission from a broad density of states in the form of stretched exponentials is observed. The corresponding spectra for pm-Si:H, on the other hand are dominated by nearly exponential fast current decay processes with discrete energies between 0.25 eV and 0.36 eV. The spectra of pm-Si:H grown at different pressures show contributions from crystallite inclusions and the medium in varying degree.     

Electronic states in a-Si:H/c-Si heterostructures

We have investigated PECVD-deposited ultrathin intrinsic a-Si:H layers on c-Si substrates using UV-excited photoemission spectroscopy (hν = 4–8 eV) and surface photovoltage measurements. For samples deposited at 230 °C, the Urbach energy is minimal, the Fermi level closest to midgap and the interface recombination velocity has a minimum. The a-Si:H/c-Si interface density of states is comparable to that of thermally oxidized silicon interfaces. However, the measured a-Si:H dangling bond densities are generally higher than in thick films and not correlated with the Urbach energy. This is ascribed to additional disorder induced by the proximity of the a-Si:H/c-Si interface and H-rich growth in the film/substrate interface region.     

Investigation of gap states in phosphorous-doped ultra-thin a-Si:H by near-UV photoelectron spectroscopy

A variant of photoelectron spectroscopy with near-UV light excitation was established and applied to an n-type doping series of ultra-thin a-Si:H layers (layer thickness ～10 nm). Using this technique, the position of the surface Fermi level E_Fs is obtained and the density of recombination active defect states in the a-Si:H band gap down to ～10¹⁵ states/cm³ can be detected. Defect densities are generally about one order of magnitude higher than in the bulk of thicker (several 100 nm) layers, and the minimum achievable distance of E_Fs from the conduction band is ～360 mV for doping with 10⁴ ppm PH₃. The optimum doping for the fabrication of solar cells is almost one order of magnitude lower. This discrepancy may be explained by enhanced recombination at the a-Si:H/c-Si interface at high doping levels, and in addition by an efficient recombination pathway where charge carriers tunnel from c-Si via a-Si:H band tail states into the a-Si:H and subsequently recombine at dangling bond states.     

Light-induced annealing of hole trap states: A new aspect of light-induced changes in hydrogenated amorphous silicon

Details of light-induced annealing of hole trap state in undoped hydrogenated amorphous silicon (a-Si:H) have been studied; it has been found that prolonged illumination significantly reduces the density of hole trap states in the energy range deeper than 0.5 eV, and subsequent thermal annealing increases the density of hole trap states and restored the sample to the initial state before the illumination. We can speculate, from the experimental results and discussion in this work, that defect conversion processes are taking place during the long exposure to light; Si dangling bonds are generated from the precursors or latent sites which manifested as hole trap states located between 0.5 and 0.7 eV from the top of the valence band.     

Luminescence decay in hydrogenated amorphous silicon and silicon nanostructures

The stretched exponential luminescence decay observed at temperatures lower than 20 K transits to the power law decay due to the electron-hopping at localized band tail states near 60 K in the hydrogenated amorphous silicon (a-Si:H). The luminescence decay at 4.2 K in a-Si:H is quite similar to that of Si-nanoparticles in the porous Si (p-Si). It is explained from the comparison with p-Si that the slow luminescence of the life time of ~ 1 ms is due to the recombination of excitonic electron–hole pairs at the spin triplet state quantum-confined in the hydrogen-free Si nanostructure in a-Si:H. The fast luminescence of the life time of ~ 1 μs is due to the recombination of the pairs at the spin-singlet state and the life time is explained as due to the indirect optical transition.     

Variation of the defect density in a-Si:H and μc-Si:H based solar cells with 2 MeV electron bombardment

Improvement of the performance of solar cells based on amorphous (a-Si:H) and microcrystalline (μc-Si:H) silicon requires understanding of the role of the deep defects – dangling bonds – in the bulk of the intrinsic a-Si:H or μc-Si:H absorber layers. A straightforward way to understand how these defects may affect the performance of the cells is to investigate changes in the device performance upon variation in the defect density.In the present work solar cells with a-Si:H and μc-Si:H absorber layers were exposed to 2 MeV electron bombardment. The performance of the cells after various bombardment doses and annealing steps was evaluated in view of the changes in the defect density of intrinsic layers, measured with ESR on nominally identical absorber layers irradiated in parallel with the cells.The defect density was varied over a range of 2 orders of magnitude. In the solar cells a strong degradation of performance is observed upon irradiation with the biggest effect on the short circuit current density J_SC for both types of absorber layers. In most cases both V_OC and J_SC recover after the final annealing step (at 160 °C) for both types of cells.     

Enhanced luminescence from Si quantum dots/SiO2 multilayers by hydrogen annealing

Si quantum dots/SiO₂ multilayers were prepared by annealing a-Si:H/SiO₂ stacked structures at 1100 °C . Photo- and electro-luminescence band around 750 nm can be observed from Si QDs/SiO₂ multilayers due to the recombination of electron-hole pairs in Si QDs/SiO₂ interfaces. The electro-luminescence intensity was obviously enhanced after post hydrogen annealing at 400 °C. Electron spin resonance measurements were used to characterize the change of the defect states after hydrogen annealing. It is found that there exists a-centers (g value = 2.006), which is related to the Si dangling bonds in Si QDs in our samples. Hydrogen annealing can significantly reduce non-luminescent a-centers and enhance the electro-luminescence intensity consequently.     

Light-induced creation of defects related to low energy photoluminescence in hydrogenated amorphous silicon

We have studied intensity and lifetime distribution of low energy photoluminescence (PL) in a-Si:H films containing native defects of various densities, prepared at various substrate temperatures, and those containing photo-created defects after illumination of pulsed light from a YAG–OPO laser system. A relation between the density of dangling bonds (DBs) and intensity of low energy PL is obtained for the films before illumination. The low energy PL in the films after illumination is stronger than that expected from the relation. The illumination does not cause sizable change of the lifetime distribution of the low energy PL of 0.95 eV. These results suggest a strongly inhomogeneous spatial distribution of photo-created DBs.     

Influence of the amorphous/crystalline silicon heterostructure properties on planar conductance measurements

We report a quasi-analytical calculation describing the heterojunction between hydrogenated amorphous silicon (a-Si:H) and crystalline silicon (c-Si) at equilibrium. It has been developed and used to determine the carrier sheet density in the strongly inverted layer at the a-Si:H/ c-Si interface. The model assumes an exponential band tail for the defect distribution in a-Si:H. The effects of the different parameters involved in the calculation are investigated in detail, such as the Fermi level position in a-Si:H, the density of states and the band offsets. The calculation was used to interpret temperature dependent planar conductance measurements carried out on (n) a-Si:H/ (p) c-Si and (p) a-Si:H/(n) c-Si structures, which allowed us to confirm a previous evaluation of the conduction band offset, ?E_C = 0.18 ± 0.05 eV, and to evaluate the valence band offset: ?E_V = 0.36 ± 0.05 eV at the a-Si:H/ c-Si heterojunction. The results are placed in the frame of recent publications.     

Recombination and transport through localized states in hydrogenated amorphous and microcrystalline silicon

Electrical transport and recombination mechanisms in hydrogenated amorphous silicon, a-Si:H, are determined by localized band-tail states and deep defects. At low temperatures (T < 100 K) the photoluminescence originates from tunneling recombination between localized band-tail states and the photoconductivity arises from hopping in the band tail. This review describes the present understanding of transport and recombination mechanisms in this low-temperature regime with a focus on two aspects: (i) the kinetics of carrier recombination and the competition between geminate and non-geminate recombination, and (ii) the microscopic identification of recombination paths by magnetic resonance techniques and the proof of excitonic recombination. Inspite of its complex nanocrystalline morphology, hydrogenated microcrystalline silicon, μc-Si:H, behaves in many respects similarly to a-Si:H in that the low-temperature properties are also determined by disorder-induced localized band-tail states.     

Effect of ex-situ hydrogen passivation on the structural properties of e-beam evaporated amorphous silicon thin film for solar cell applications

Thin-film photovoltaics greatly reduce the semiconductor material content in the finished product, using 150–200 times less material as compared with conventional Si wafer based cells. Electron beam evaporation (e-beam), a non-ultra-high vacuum technique has the potential for being inexpensive, and simpler process for a-Si deposition. It offers specific advantages such as high Si deposition rate (up to 1 μm/min), excellent Si source material usage, avoidance of toxic gases, and simple sample preparation conditions. In this work, we report the growth of a-Si films using e-beam at a growth rate exceeding 30 Å/s (1–5 Å/s for conventional PECVD process). We report the effect of hydrogen passivation on amorphous silicon network and on silicon-bonded hydrogen configuration under ex-situ hydrogenation in hydrogen plasma. The hydrogen concentration and silicon-hydrogen bonding configuration was evaluated using nuclear reaction analysis (NRA) and Fourier transform infrared spectroscopy (FTIR). Hydrogen plasma treatment shows an increase in the monohydride bond concentration with substrate temperature, and is corroborated by our FTIR investigation, in addition to reducing clustered monohydride bonds or polyhydride bonds in a-Si:H film. Raman analysis indicates reduction in silicon bond angle as well as the bond distance, both leading to significant structural improvement in short-range and medium range order in the amorphous phase. Thus, ex-situ hydrogenation clearly demonstrates the possibility of comparable hydrogen passivation in e‐beam evaporated a-Si films with high growth rate. One can easily extrapolate this result to microcrystalline film growth, assuming the structural improvement of the silicon network preceding the microcrystalline nucleation, where ex-situ passivation is most effective. Thus ex-situ hydrogenation opens up new possibilities in minutely tailoring the a:Si film properties especially for solar cell applications.     

Spatially localized current-induced crystallization of amorphous silicon films

Field-enhanced metal-induced solid phase crystallization (FE-MISPC) at room temperature is employed to create microscopic crystalline regions at predefined positions in hydrogen-rich amorphous silicon (a-Si:H) films. Electric field is applied locally using a sharp conductive tip in atomic force microscope (AFM) and nickel electrode below the a-Si:H film. The process is driven by a constant current of ?50 pA to ?500 pA while controlling the amount of transferred energy (1–300 nJ) as a function of time. Passing current leads to a formation of nanoscale pits in the a-Si:H films. Depending on the energy amount and rate the pits exhibit lower or orders of magnitude higher conductivity as detected by current-sensing AFM. High conductivity is attributed to a local crystallization of the films. This is confirmed by micro-Raman spectroscopy.     

Charge collection in amorphous silicon solar cells: Cell analysis and simulation of high-efficiency pin devices

The drift length L_drift = μτE within the i layer of a-Si:H solar cells is a crucial parameter for charge collection and efficiency. It is strongly reduced not only by light-induced reduction of μτ, but also by electric field deformation ΔE by charges near the p–i and i–n interfaces. Here, a simple model is presented to estimate contributions of free carriers, charges trapped in band tails and charged dangling bonds to ΔE. It is shown that the model reproduces correctly trends observed experimentally and by ASA simulations: charged dangling bonds contribute most to ΔE of meta-stable cells. Electrons trapped in the conduction band tail near the i–n interface lead to the strongest field deformation in the initial state, while positively charged dangling bonds near the p–i interface get more important with degradation under AM1.5g spectrum. The measurable parameter V_coll is proposed as an indirect parameter to estimate the electric field, and an experimental technique is presented that could enable the distinction of defects near the p–i and the i–n interfaces.     

Understanding the photoluminescence over 13-decade lifetime distribution in a-Si:H

Wideband quadrature frequency resolved spectroscopy (QFRS) expanded from 2 ns to 160 s revealed that the triple-peaked lifetime distribution observed in the photoluminescence (PL) of a-Si:H consists of the well-known double-peak structure and a newly identified third component. By the exploring dependence of the lifetime distribution on the generation rate G, temperature T, PL emission energy E_PL, PL excitation energy E_X and external magnetic field, the former is assigned to excitonic recombination and the latter to distant-pair (DP) or nongeminate recombination. The DP component gives the same sublinear G and T dependence as light-induced electron spin resonance (LESR) results. The present paper also shows that the residual PL decay in a-Si:H persists for more than 10⁴ s, which corresponds the DP component and agrees with the LESR results. The residual PL decay reveals that the DP recombination kinetics is monomolecular at low T and low G.     

Amorphous silicon diamond based heterojunctions with high rectification ratio

We have fabricated and characterized diamond based heterojunctions composed of homoepitaxial diamond (B-doped film: p type) and hydrogenated amorphous silicon (a-Si:H film: n-type). All devices include an intrinsic amorphous silicon interface (i-a-Si:H). (J–V) characteristics of a-Si:H heterojunctions measured from 300 K to 460 K present a very high rectification ratio (in the range 10⁸–10⁹) and a current density of 10 mA/cm² under 2 V of forward bias. The reverse current up to ? 4 V is below the detection limit in the whole temperature range. The devices present two regimes of operation indicating that more than one mechanism governs the carrier transport. These characteristics are compared with a Schottky barrier diode (SBD) using a tungsten carbide metal on top of the p-type diamond as a Schottky contact. The SBD device exhibits J–V characteristic with an ideality factor n close to one and the heterojunction follows this trend for low bias voltages whereas for bias voltage above 1 V a second regime with larger ideality factors n ~ 3.6 is observed. These results point out the prominent role of transport mechanisms at heterointerface between the a-Si:H layers and the p-type doped diamond which degrades the current injection. The breakdown voltage reached ? 160 V indicating the good quality of the deposited layers.     

Characterization of a-B5C:H prepared by PECVD of orthocarborane: Results of preliminary FTIR and nuclear reaction analysis studies

The electronic properties of a-Si:H vary with hydrogen passivation of dangling bond defects. It appears this effect is also operative in semiconducting amorphous hydrogenated boron carbide (a-B₅C:H). Therefore, the ability to quantify the amount of hydrogen will be key to development of the materials science of a-B₅C:H. The results of an initial investigation probing the ability to quickly correlate hydrogen concentration in a-B₅C:H films with infrared spectroscopy are reported. a-B₅C:H thin films were growth on Si (1 1 1) substrates by plasma-enhanced chemical vapor deposition (PECVD) using sublimed orthocarborane and argon as the precursor gas. Nuclear reaction analysis (NRA) was performed to quantify the atomic concentration of H in the a-B₅C:H films. While the observed vibronic structure does not show stretches due to terminal C–H or bridging B–H–B, analysis of the terminal B–H stretch at ～2570 cm^?1 gives a proportionality constant of A = 2 × 10²² cm^?2. We conclude that the methods previously developed for correlating H concentration to infrared data in a-Si:H are similarly viable for a-B₅C:H films.     

Heat treatment of amorphous silicon p-i-n solar cells with high-pressure H2O vapor

We report improvement in characteristics of hydrogenated amorphous silicon (a-Si:H ) p-i-n structured solar cells by high-pressure H₂O vapor heat treatment. a-Si:H p-i-n solar cells were formed on glass substrates coated with textured SnO₂ layer. P-, i-, and n-type a-Si:H layers were subsequently formed by plasma enhanced chemical vapor deposition. Finally an indium-tin-oxide layer was coated on the n-type a-Si:H surface. Heat treatment at 210 °C with 2 × 10⁵ Pa H₂O vapor for 1 h was applied to the a-Si:H p-i-n solar cells. Electrical characteristics were measured when samples were kept in dark and illuminated with light of AM 1.5 at 100 mW/cm². The heat treatment with H₂O vapor increased fill factor (FF) and the conversion efficiency from 0.54 and 7.7% (initial) to 0.57 and 8.4%, respectively. Marked improvement in solar cell characteristics was also observed in the case of a poor a-Si:H p-i-n solar cell. FF and the conversion efficiency were increased from 0.29 and 3.2% (initial) to 0.56 and 7.7%, respectively.     

Voids in hydrogenated amorphous silicon materials

Effusion measurements of hydrogen and of implanted helium are used to characterize the presence of voids in hydrogenated amorphous silicon (a-Si:H) materials as a function of substrate temperature, hydrogen content, etc. For undoped plasma-grown a-Si:H, interconnected voids are found to prevail at hydrogen concentrations exceeding 15–20 at.%, while isolated voids which act as helium traps appear at hydrogen concentrations ≤ 15 at.%. The concentration of such isolated voids is estimated to some 10¹⁸/cm³ for device-grade undoped a-Si:H deposited at a substrate temperature near 200 °C. Higher values are found for, e.g., doped material, hot wire grown a-Si:H and hydrogen-implanted crystalline Si. The results do not support recent suggestions of predominant incorporation of hydrogen in a-Si:H in (crystalline silicon type) divacancies, since such models predict a concentration of voids (which act as helium traps) in the range of 10²¹/cm³ and a correlation between void and hydrogen concentrations which is not observed.     

Fabrication and characterization of nanorod solar cells with an ultrathin a-Si:H absorber layer

In this paper, we present a three-dimensional nanorod solar cell design. As the backbone of the nanorod device, density-controlled zinc oxide (ZnO) nanorods were synthesized by a simple aqueous solution growth technique at 80 °C on ZnO thin film pre-coated glass substrate. The as-prepared ZnO nanorods were coated by an amorphous hydrogenated silicon (a-Si:H) light absorber layer to form a nanorod solar cell. The light management, current–voltage characteristics and corresponding external quantum efficiency of the solar cells were investigated. An energy conversion efficiency of 3.9% was achieved for the nanorod solar cells with an a-Si:H absorber layer thickness of 75 nm, which is significantly higher than the 2.6% and the 3.0% obtained for cells with the same a-Si:H absorber layer thickness on planar ZnO and on textured SnO₂:F counterparts, respectively. A short-circuit current density of 11.6 mA/cm² and correspondingly, a broad external quantum efficiency profile were achieved for the nanorod device. An absorbed light fraction higher than 80% in the wavelength range of 375–675 nm was also demonstrated for the nanorod solar cells, including a peak value of ~ 90% at 520–530 nm.     

Distribution of hydrogen in low temperature passivated amorphous silicon (a-Si:H) films from neutron reflectivity

Hydrogen plays a critical role in the passivation of dangling bonds in hydrogenated amorphous silicon (a-Si:H) to enable acceptable semiconducting characteristics during operation in devices. Low temperature processing enables fabrication of high performance transistors on flexible substrates such as plastic or stainless steel foils, but also leads to a decrease in the stability of the electronic performance. Generation of defects at the a-Si:H/insulator (hydrogenated silicon nitride, SiN:H) during electrical use due to localized heating will lead to decreased performance unless the dangling bonds are passivated in-situ by residual hydrogen. For this reason, the distribution of hydrogen within a-Si:H may be critical to understanding their aging phenomena. Here the distribution of hydrogen within both a-Si:H and SiN:H layers is probed with sub-nanometer resolution using neutron reflectivity. The hydrogen concentration within the bulk of the a-Si:H (11 ± 2 at.%) and SiN:H (18 ± 3 at.%) agree well with previous reports, but the increased resolution of the neutron measurement is able to identify an approximate three fold increase in the concentration within 2 nm of the semiconductor-insulator interface. This enhanced hydrogen content may act in the short-term as a sink to passivate any dangling bonds formed during operation.