(Liquid + liquid) equilibrium of (water + 2-propanol + 1-butanol + salt) systems at T = 313.15 K and T = 353.15 K: Experimental data and correlation

(Liquid + liquid) equilibrium data for the quaternary systems (water + 2-propanol + 1-butanol + potassium bromide) and (water + 2-propanol + 1-butanol + magnesium chloride) were measured at T = 313.15 K and T = 353.15 K. The overall salt concentrations were 5 and 10 mass percent. Ternary (liquid + liquid) equilibrium data for the salt-free system (water + 2-propanol + 1-butanol) were also determined and found to be in good agreement with data from the literature. The NRTL model for the activity coefficient was used to correlate the data. New interaction parameters were estimated, using the Simplex minimization method and a concentration-based objective function. The results are very satisfactory, with root mean square deviations between experimental and calculated compositions of both phases being less than 0.5%.     

Liquid heat capacity of the solvent system (piperazine + n-methyldiethanolamine + water)

A new set of values for the heat capacity of aqueous mixtures of piperazine (PZ) and n-methyldiethanolamine (MDEA) at different concentrations and temperatures are reported in this paper. The differential scanning calorimetry technique was used to measure the property over the range T = 303.2 K to T = 353.2 K for mixtures containing 0.60 to 0.90 mole fraction water with 15 different concentrations of the system (PZ + MDEA + H₂O). Heat capacity for four concentrations of the binary system (PZ + MDEA) was also measured. A Redlich–Kister-type equation was adopted to estimate the excess molar heat capacity, which was used to predict the value of the molar heat capacity at a particular concentration and temperature, which would then be compared against the measured value. A total of 165 data points fit into the model resulted in a low overall average absolute deviation of 4.6% and 0.3% for the excess molar heat capacity and molar heat capacity, respectively. Thus, the results presented here are of acceptable accuracy for use in engineering process design.     

(Liquid + liquid) equilibria of (tert -amyl ethyl ether + ethanol + water) at several temperatures

(Liquid  +  liquid) equilibrium data of (tert amyl ethyl ether  +  ethanol  +  water) were determined experimentally atT =  (298.15, 308.15, and 318.15) K. The experimental results were correlated with the NRTL and UNIQUAC equations. The correlations were made at each temperature and for the three temperatures simultaneously. The best results were achieved with the NRTL equation, using α =  0.2 for the individual correlations at each temperature and α =  0.1 for the overall correlation. The experimental data were also compared with predicted values by the UNIFAC method.     

(Liquid + liquid) equilibrium of {water + phenol + (1-butanol,or 2-butanol,or tert-butanol)} systems

(Liquid + liquid) equilibrium (LLE) and binodal curve data were determined for the systems (water + phenol + tert-butanol) at T = 298.15 K, (water + phenol + 2-butanol) and (water + phenol + 1-butanol) at T = 298.15 K and T = 313.15 K by the combined techniques of densimetry and refractometry. Type I curve (for tert-butanol) and Type II curves (for 1- and 2-butanol) were found. The data were correlated with the NRTL model and the parameters estimated present root mean square deviations below 2% for the system with tert-butanol and lower than 0.8% for the other systems.     

(Vapour + liquid) equilibrium and excess Gibbs functions of ternary mixtures containing 1-butanol or 2-butanol,n-hexane,and 1-chlorobutane at T = 298.15 K

Isothermal (vapour + liquid) equilibrium data for the ternary mixtures 1-butanol + n-hexane + 1-chlorobutane and 2-butanol + n-hexane + 1-chlorobutane have been studied with a recirculating still at T = 298.15 K. The experimental data were satisfactorily checked for thermodynamic consistency using the method of van Ness. Activity coefficients and excess Gibbs function have been correlated with the Wilson equation. The G^E values obtained for the two ternary systems are very similar.     

Vapour pressures,densities, and viscosities of the (water + lithium bromide + potassium acetate) system and (water + lithium bromide + sodium lactate) system

Measurements of thermophysical properties (vapour pressure, density, and viscosity) of the (water + lithium bromide + potassium acetate) system LiBr:CH₃COOK = 2:1 by mass ratio and the (water + lithium bromide + sodium lactate) system LiBr:CH₃CH(OH)COONa = 2:1 by mass ratio were measured. The system, a possible new working fluid for absorption heat pump, consists of absorbent (LiBr + CH₃COOK) or (LiBr + CH₃CH(OH)COONa) and refrigerant H₂O. The vapour pressures were measured in the ranges of temperature and absorbent concentration from T = (293.15 to 333.15) K and from mass fraction 0.20 to 0.50, densities and viscosities were measured from T = (293.15 to 323.15) K and from mass fraction 0.20 to 0.40. The experimental data were correlated with an Antoine-type equation. Densities and viscosities were measured in the same range of temperature and absorbent concentration as that of the vapour pressure. Regression equations for densities and viscosities were obtained with a minimum mean square error criterion.     

(Liquid + liquid) equilibria in {water + acrylic acid + (1-butanol,or 2-butanol,or 1-pentanol)} systems at T = 293.2 K,T = 303.2 K,and T = 313.2 K and atmospheric pressure

(Liquid + liquid) equilibrium (LLE) data for {water + acrylic acid + (1-butanol, or 2-butanol, or 1-pentanol)} at T = 293.2 K, T = 303.2 K, and T = 313.2 K and atmospheric pressure (≈95 kPa) were determined by Karl Fischer titration and densimetry. All systems present type I binodal curves. The size of immiscibility region changes little with an increase in temperature, but increases according to the solvent, following the order: 2-butanol < 1-butanol < 1-pentanol. Values of solute distribution and solvent selectivities show that 1-pentanol is a better solvent than 1-butanol or 2-butanol for acrylic acid removal from water solutions. Quality of data was ascertain by Hand and Othmer-Tobias equations, giving R² > 0.916, mass balance and accordance between tie lines and cloud points. The NRTL model was used to correlate experimental data, by estimating new energy parameters, with root mean square deviations below 0.0053 for all systems.     

Thermodynamic study of the system (LiCl + LiNO3 + H2O)

The solubility of the binary system (LiNO₃ + H₂O) from T = 273.15 K to T = 333.15 K and solubility isotherms of the ternary system (LiCl + LiNO₃ + H₂O) were elaborately measured at T = 273.15 K and T = 323.15 K. These solubility data, as well as water activities in the binary systems from the literature, were treated by an empirically modified BET model. The isotherms of the ternary system (LiCl + LiNO₃ + H₂O) were reproduced and a complete phase diagram of the ternary system in the temperature range from 273.15 K to 323.15 K predicted. It is shown that the solubility data for the binary system (LiNO₃ + H₂O) measured in this work are slightly different from the literature data. Simulated results showed that the saturated salt solution of (2.8LiCl + LiNO₃) is in equilibrium with the stable solid phase LiNO₃(s) over the temperature range from 283.15 K to 323.15 K, other than the solid phases LiNO₃ · 3H₂O(s) and LiClH₂O(s) as reported by Iyoki et al. [S. Iwasaki, Y. Kuriyama. T. Uemura, J. Chem. Eng. Data 38 (1993) 396–398].     

Estimation of (vapour + liquid) equilibrium of binary systems (tert-butanol + 2-ethyl-1-hexanol) and (n-butanol + 2-ethyl-1-hexanol) using an artificial neural network

(Vapour + liquid) equilibrium (VLE) data are important for designing and modelling of process equipment. Since it is not always possible to carry out experiments at all possible temperatures and pressures, generally thermodynamic models based on equations of state are used for estimation of VLE. In this paper, an alternate tool, i.e. the artificial neural network technique has been applied for estimation of VLE for the binary systems viz. (tert-butanol + 2-ethyl-1-hexanol) and (n-butanol + 2-ethyl-1-hexanol). The temperature range over which these models are valid is (353.2 to 458.2) K at atmospheric pressure. The average absolute deviation for the temperature output was in range 2% to 3.3%. The results were then compared with experimental data.     

Volumetric properties of ternary (IL + 2-propanol or 1-butanol or 2-butanol + ethyl acetate) systems and binary (IL + 2-propanol or 1-butanol or 2-butanol) and (1-butanol or 2-butanol + ethyl acetate) systems

The experimental densities for the binary or ternary systems were determined at T = (298.15, 303.15, and 313.15) K. The ionic liquid methyl trioctylammonium bis(trifluoromethylsulfonyl)imide ([MOA]⁺[Tf₂N]⁻) was used for three of the five binary systems studied. The binary systems were ([MOA]⁺[Tf₂N]⁻ + 2-propanol or 1-butanol or 2-butanol) and (1-butanol or 2-butanol + ethyl acetate). The ternary systems were {methyl trioctylammonium bis(trifluoromethylsulfonyl)imide + 2-propanol or 1-butanol or 2-butanol + ethyl acetate}. The binary and ternary excess molar volumes for the above systems were calculated from the experimental density values for each temperature. The Redlich–Kister smoothing polynomial was fitted to the binary excess molar volume data. Virial-Based Mixing Rules were used to correlate the binary excess molar volume data. The binary excess molar volume results showed both negative and positive values over the entire composition range for all the temperatures.The ternary excess molar volume data were successfully correlated with the Cibulka equation using the Redlich–Kister binary parameters.     

(Liquid + liquid) equilibrium for the system {ethyl stearate(1) + ethanol(2) + glycerol(3)}

This paper reports the results of a new experimental study on the (liquid + liquid) equilibrium of the system {ethyl stearate(1) + ethanol(2) + glycerol(3)} at atmospheric pressure and at T = (313.15 and 323.15) K. The equilibrium compositions were measured by gas chromatography. Ternary diagrams were obtained for each temperature and the equilibrium data were compared to the system in the presence of salt (NaCl) at T = 323.15 K. The experimentally determined (liquid + liquid) equilibrium data were satisfactorily correlated with NRTL and UNIQUAC equations. A comparative analysis was performed using the UNIFAC-LLE group contribution method. From the results presented herein good predictions were obtained for this ternary system.     

Thermodynamic properties of (tetradecane + benzene, + toluene, + chlorobenzene, + bromobenzene, + anisole) binary mixtures at T = (298.15, 303.15, and 308.15) K

Density ρ, viscosity η, and refractive index n_D, values for (tetradecane + benzene, + toluene, + chlorobenzene, + bromobenzene, + anisole) binary mixtures over the entire range of mole fraction have been measured at temperatures (298.15, 303.15, and 308.15) K at atmospheric pressure. The speed of sound u has been measured at T = 298.15 K only. Using these data, excess molar volume V^E, deviations in viscosity Δη, Lorentz–Lorenz molar refraction ΔR, speed of sound Δu, and isentropic compressibility Δk_s have been calculated. These results have been fitted to the Redlich and Kister polynomial equation to estimate the binary interaction parameters and standard deviations. Excess molar volumes have exhibited both positive and negative trends in many mixtures, depending upon the nature of the second component of the mixture. For the (tetradecane + chlorobenzene) binary mixture, an incipient inversion has been observed. Calculated thermodynamic quantities have been discussed in terms of intermolecular interactions between mixing components.     

Dynamic viscosities of the ternary liquid mixtures (dimethyl carbonate + methanol + ethanol) and (dimethyl carbonate + methanol + hexane) at several temperatures

Densities, ρ speeds of sound, u and dynamic viscosities, η of the ternary mixtures {dimethyl carbonate (DMC) + methanol + ethanol} and (dimethyl carbonate + methanol + hexane) were gathered at T = (293.15, 298.15, 308.15, and 313.15) K. From experimental data viscosity deviations, Δη of the ternary mixtures were evaluated. These results have been correlated using the Cibulka equation. The fitting parameters and the standard deviations of the ternary viscosity deviations are given. UNIFAC-VISCO group contribution method was used to predict the dynamic viscosities of the ternary mixtures at several temperatures.     

Equilibrium solubility of sodium 2-naphthalenesulfonate in binary (sodium chloride + water), (sodium sulfate + water), and (ethanol + water) solvent mixtures at temperatures from (278.15 to 323.15) K

The equilibrium solubility of sodium 2-naphthalenesulfonate in binary (sodium chloride + water), (sodium sulfate + water), and (ethanol + water) solvent mixtures was measured at elevated temperatures from (278.15 to 323.15) K using a steady-state method. With increasing temperatures, the solubility increases in aqueous solvent mixtures. The results of these results were regressed by a modified Apelblat equation. The dissolution entropy and enthalpy determined using the method of the least-squares and the change of Gibbs free energy calculated with the values of Δ_diffS^o and Δ_diffH^o at T = 278.15 K.     

Thermodynamic evaluation and optimization of the (NaCl + KCl + MgCl2 + CaCl2 + MnCl2 + FeCl2 + CoCl2 + NiCl2) system

A complete critical evaluation of all available phase diagram and thermodynamic data has been performed for all condensed phases of the (NaCl + KCl + MgCl₂ + CaCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) system, and optimized model parameters have been found. The (MgCl₂ + CaCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) subsystem has been critically evaluated in a previous article. The model parameters obtained for the binary subsystems can be used to predict thermodynamic properties and phase equilibria for the multicomponent system. The Modified Quasichemical Model was used for the molten salt phase, and the (MgCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) solid solution was modeled using a cationic substitutional model with an ideal entropy and an excess Gibbs free energy expressed as a polynomial in the component mole fractions. Finally, the (Na,K)(Mg,Ca,Mn,Fe,Co,Ni)Cl₃ and the (Na,K)₂(Mg,Mn,Fe,Co,Ni)Cl₄ solid solutions were modeled using the Compound Energy Formalism.     

Mean activity coefficient measurement and thermodynamic modelling of the ternary mixed electrolyte (MgCl2 + glucose + water) system at T = 298.15 K

In this work, the mean activity coefficients of MgCl₂ in pure water and (glucose + water) mixture solvent were determined using a galvanic cell without liquid junction potential of type: (Mg²⁺ + ISE)|MgCl₂ (m), glucose (wt.%), H₂O (100 wt.%)|AgCl|Ag. The measurements were performed at T = 298.15 K. Total ionic strengths were from (0.0010 to 6.0000) mol · kg⁻¹. The various (glucose + water) mixed solvents contained (0, 10, 20, 30 and 40)% mass fractions percentage of glucose respectively. The mean activity coefficients measured were correlated with Pitzer ion interaction model and the Pitzer adjustable parameters were determined. Then these parameters were used to calculate the thermodynamics properties for under investigated system. The results showed that Pitzer ion interaction model can satisfactory describe the investigated system. The modified three-characteristic-parameter correlation (TCPC) model was applied to correlate the experimental activity coefficient data for under investigation electrolyte system, too.     

Modeling of the quaternary NaCl + KCl + CH3OH + H2O mixed electrolyte system: Binary and ternary mixing (ion + ion) and (ion + nonelectrolyte) interaction parameters

The purpose of this work is modeling of the quaternary system of mixed NaCl + KCl electrolyte in mixed CH₃OH + H₂O solvent, with different alcohol mass fractions by using particularly, the Pitzer (P) and Pitzer–Esteso (PE) equations and based on potentiometric measurement technique. The experimental data are obtained by different molal salt ratio r (r = m_NaCl/m_KCl = 100, 150, 200 and 250) in mixed solvent with different alcohol mass fractions x (x = 0.10, 0.20, 0.30, 0.40, and 0.50) in water. A galvanic cell is employed for collecting the potentiometric data by combining a Na⁺ glass membrane and Ag/AgCl electrodes and using different series of electrolyte solutions, at defined constant ionic strengths, with the molality ranging from 0.0005 up to 3.5 mol · kg⁻¹, at T = 298.15 ± 0.05 K of experiments. Comparison of the models shows that the modified Pitzer equation by Esteso (PE) present a better fit of the experimental data.     

(Liquid + liquid) equilibria of the (water + propionic acid + Aliquat 336 + organic solvents) at T = 298.15 K

In this work, trioctyl methyl ammonium chloride (Aliquat 336) was studied for its ability to extract propionic acid at various amine concentrations. The extraction of propionic acid with Aliquat 336 dissolved in five single solvents (cyclohexane, hexane, toluene, methyl isobutyl ketone, and ethyl acetate ) and binary solvents (hexane + MIBK, hexane + toluene, and MIBK + toluene) was investigated under various experimental conditions. The loading factors Z, extraction efficiency E and overall particular distribution coefficients were determined. All measurements were carried out at T = 298.15 K. The obtained results and the observed phenomena were discussed by taking into consideration the mechanism of extraction and the concentration of the interaction product in the aqueous phase.     

Ternary (liquid + liquid) equilibria for mixtures of (methanol + aniline + n-octane or n-dodecane) at T = 298.15 K

(Liquid + liquid) equilibrium (LLE) data for the ternary mixtures of (methanol + aniline + n-octane) and (methanol + aniline + n-dodecane) at T = 298.15 K and ambient pressure are reported. The compositions of liquid phases at equilibrium were determined and the results were correlated with the UNIQUAC and NRTL activity coefficient models. The partition coefficients and the selectivity factor of methanol for the extraction of aniline from the (aniline + n-octane or n-dodecane) mixtures are calculated and compared. Based on these comparisons, the efficiency of methanol for the extraction of aniline from (aniline + n-dodecane) mixtures is higher than that for the extraction of aniline from (aniline + n-octane) mixtures. The phase diagrams for the ternary mixtures including both the experimental and correlated tie lines are presented. From the phase diagrams and the selectivity factors, it is concluded that methanol may be used as a suitable solvent in extraction of aniline from (aniline + n-octane or n-dodecane) mixtures.     

Phase equilibrium properties of binary and ternary systems containing di-isopropyl ether + 1-butanol + benzene at 313.15 K

(Vapour + liquid) equilibria data of (di-isopropyl ether + 1-butanol + benzene), (di-isopropyl ether + 1-butanol) and (1-butanol + benzene) have been measured at T = 313.15 K using an isothermal total pressure cell. Data reduction by Barker’s method provides correlations for the excess molar Gibbs energy using the Margules equation for the binary systems and the Wohl expansion for the ternary. The Wilson, NRTL and UNIQUAC models have been applied successfully to both the binary and the ternary systems reported here.