Polyaniline/thermoplastic polyurethane blends: Preparation and evaluation of electrical conductivity

Conducting polymer blends whose undiluted components have different properties are promising materials for specific applications and have attracted interest in recent years. The aim of this study was to obtain and evaluate the electrical conductivity of polyaniline doped with dodecylbenzenesulfonic acid (PAni.DBSA)/polyurethane thermoplastic (TPU) blends. The PAni.DBSA was synthesized from DBSA-aniline (DBSAn) salt through an emulsion polymerization in tetrahydrofurane (THF) or in the presence of polyurethane thermoplastic solution, resulting in pure PAni.DBSA or PAni.DBSA/TPU blends. Blends of PAni.DBSA/TPU were also prepared through casting, at room temperature, after dissolving both components in THF as a common solvent. The insulator-conductor transition was very sharp and the percolation threshold was lower than 2.7 wt% of PAni.DBSA. The electrical conductivity of PAni.DBSA/TPU blends, prepared by both methods, reached maximum values at a PAni.DBSA concentration of 40 wt%, close to the value observed for the undiluted conducting polymer. However, for a PAni.DBSA content lower than 30 wt%, the electrical conductivity was dependent on the blend preparation method. Blends were characterized by infrared spectroscopy, thermogravimetric analysis (TG) and optical microscopy. The electrical conducting characteristics of the PAni.DBSA/TPU blends prepared using different procedures indicate a high potential for their successful application in electrical processes.     

Swelling characteristics and application of gamma-radiation on irradiated SBR-carboxymethylcellulose (CMC) blends

Blends of styrene butadiene rubber (SBR) with varying loading degree from 60 wt% to 100 wt% of carboxymethylcellulose (CMC) have been prepared. Gamma radiation vulcanization of prepared blends was carried out with doses varying between 50 kGy and 250 kGy. Mechanical properties, namely, tensile strength (Ts), elongation at break (E_b) and hardness were followed up as a function of loading degree of CMC and gamma irradiation dose. Moreover, physical properties, specifically swelling number (SN) and gel fraction % (GF%) were undertaken. Results obtained showed an improvement in mechanical as well as in physical properties with increasing either CMC content or dose of irradiation. Thermal properties namely thermo gravimetric analysis (TGA) was carried out.     

Radiation induced in-situ generation of conductivity in the blends of polyaniline-base with chlorinated-polyisoprene

Radiation induced acid doping of PANI to generate electrical conductivity was achieved by radiation induced HCl release from chlorinated-polyisoprene (ClPIP). Blends of PANI with ClPIP were prepared by mechanical mixing/grinding in the composition range of 9–43% ClPIP by weight and pelletized under 10 t press. The pellets were irradiated in ⁶⁰Co Gammacell in air at room temperature to doses up to 300 kGy. The maximum electrical conductivity increase was observed for the blend PANI43 which changed from 10^?10 to 10^?4 S cm^?1 when it was irradiated to 300 kGy dose. Radiation induced changes on the blends were also studied by UV–vis spectroscopy using reflection technique and FTIR spectroscopy. The broad absorption band in the visible range (630 nm) increased by increasing irradiation dose. The band (1110 cm^?1) in the IR spectra which is indicative of conductivity showed linear correlation with irradiation dose.     

Molecular mechanics investigation of some acrylic polymers using SPASIBA force field

The First generation SPASIBA force field is used to study normal vibrational modes of PMMA, and then extended to other thermoplastic polymers, namely PMA, PMAA and PAA, in order to determine its parameters transferability. To this end, FTIR and FTR spectra of pure PMMA samples, prepared by the emulsion polymerization of MMA and initiated by sodium, are recorded in 400–3500 cm⁻¹ and 200–3500 cm⁻¹, respectively. A detailed vibrational analysis was performed on the obtained spectra and the observed frequencies are assigned to their respective vibrational modes, supported by potential energy distribution (PED) analysis. Our numerical results reveal an RMS value of 7.8 cm⁻¹ corresponding to IR wavenumbers and 8.7 cm⁻¹ relatively to Raman wavenumbers. Our vibrational calculations on PMA, PMAA and PAA polymers reveal that the parameters transferability criterion, established by Shimanouchi, is verified for the SPASIBA force field.     

Highly efficient enzyme immobilization by nanocomposites of metal organic coordination polymers and carbon nanotubes for electrochemical biosensing

New nanocomposites with multi-walled carbon nanotubes (MWCNTs) embedded in metal-organic coordination polymers (MOCPs) were successfully prepared as highly efficient matrices of enzyme immobilization for sensitive electrochemical biosensing. NaAuCl₄ was pre-adsorbed on the MWCNTs to act as anchor sites to further coordinate with ligand benzenedithiol and form MOCPs. The formation of MWCNTs-MOCPs one-pot entrapped glucose oxidase (GOx) with a ratio close to 100% and exhibited enhanced mass-transfer over MOCPs. Thus MWCNTs-MOCPs-modified electrodes present superior enzymatic catalysis performance of greatly enhanced sensitivity (136 μA cm^− 2 mM^− 1) and magnitudes-lower detection limit (48 nM), being superior to most analogues.     

Efficient preparation of carbon papers by pyrolysis of iodine-treated Japanese paper

A novel carbon paper has been prepared by pyrolysis from traditional Japanese paper called washi in Japan, which is mainly composed of cellulose microfibers. The washi was iodine-treated before pyrolysis. The effect of iodine-treatment on pyrolysis of the washi was investigated using thermogravimetric analysis. The structural and electrical properties of the carbon papers were also investigated using Raman scattering, X-ray diffraction, electron microscopy, and resistivity measurements. The iodine-treatment prevents cellulose from thermally decomposing and is effective in increasing the carbon yield and retaining its fibrillar structure. Porous carbon papers consisting of many micro and nanofibrils were prepared by the pyrolysis of the iodine-treated washi at 800 °C. Those prepared at 800 °C and then heat-treated at higher temperatures than 1800 °C show electrical conductivities of 3 S cm⁻¹ and 24–27 S cm⁻¹. The degree of crystallinity and the electrical conductivity of the papers are improved by the heat treatment at higher temperatures.     

Thermogravimetric and FTIR studies of chitosan blends

Results of spectrophotometric and thermogravimetric studies of chitosan (CH) blends with polyvinyl alcohol (PVAL), starch (S) and hydroxypropylcellulose (HPC) obtained by casting from solutions in the form of transparent films containing 0–1.0 weight fraction of CH were discussed. Blends containing S are homogeneous only in the case of low-weight fraction of S (to 0.3).On the basis of results of thermodegradation in dynamic and isothermal conditions, thermal stability of the tested systems was estimated. Thermogravimetric measurements in dynamic conditions were carried out in the temperature range of 100–450 °C at constant heating rate 15 °C/min. From thermogravimetry (TG) and DTG curves the activation energy and characteristic parameters of degradation of the tested blends were determined. The observed growth of activation energy and T_p—temperature of initial weight loss, T_max—temperature of maximal rate and C_e—degree of conversion at the end of the measurement (at temperature 450 °C) along with the increase of polymer fraction (HPC and S) in the CH blend provides an evidence of improved thermal stability of the systems tested.Investigations in isothermal conditions in air at temperature from 100 to 200 °C confirmed appreciable improvement of CH thermal stability in the blends being tested.Infrared spectroscopic analysis of the blends showed a distinct stabilization of the process of chain scission. In the band at 1080 cm⁻¹ associated with absorption in –C–O–C– group during degradation of the blends at temperature 200 °C much smaller decrease due to molecular scission were observed than in the case of pure CH.     

Aliphatic thioether polymers as novel cathode active materials for rechargeable lithium battery

Two aliphatic thioether polymers, poly[methanetetryl-tetra(thiomethylene)] (PMTTM) and poly(2,4-dithiopentanylene) (PDTP) were designed, synthesized, characterized and tested as cathode active materials. The chemical structure of polymers was confirmed by FT-IR, FT-Raman, and XPS spectral analysis. Both polymers were found to have electrochemical activity as cathode materials for rechargeable lithium battery by the electrochemical tests. The specific capacity of PMTTM was 504 mA h g⁻¹ at the third cycle and faded to 200 mA h g⁻¹ after 10 cycles; PDTP showed low and stable specific capacity around 100 mA h g⁻¹ even after 50 cycles. The specific capacity of fully saturated aliphatic thioether polymers demonstrated that thioether bonds offered energy storage. It was proposed that thioether bond was oxidized to form thioether cations with the help of ether solvents.     

In situ quantification of electrochemical dissolution of hafnium-tantalum alloys in acidic media

A thin film hafnium-tantalum combinatorial library with a compositional spread of over 70 at.% was used for electrochemical dissolution experiments in nitric acid. Surface microstructure analysis and crystallographic characterization of individual Hf–Ta alloys confirmed a hexagonal to tetragonal transition from pure Hf to pure Ta accompanied by a change in the surface grain structure. A flow-type scanning droplet cell microscope coupled to downstream analytics was used for the quantification of Hf and Ta dissolution rates along the entire compositional spread. Potentiostatically applying 3 V vs. SHE for 120 s for an electrolyte flow of 0.46 ml min^− 1 resulted in dissolution rates of pure Hf and pure Ta in the ng s^− 1 cm^− 2 and pg s^− 1 cm^− 2 range, respectively. For both species, the average dissolution rate was independent of the compositional gradient, indicating a dissolution enhancement of minor species. A decrease in their activation energy for dissolution triggered by a surface energy modification was the reason for the observed behavior.     

Life test of DMFC using poly(ethylene glycol)bis(carboxymethyl)ether plasticized PVA/PAMPS proton-conducting semi-IPNs

A novel, low-cost proton-conducting semi-IPN has been successfully prepared from PVA/PAMPS blends by incorporating poly(ethylene glycol)bis(carboxymethyl)ether (PEGBCME) as a novel plasticizer. Although, the polymer is based on a relatively low content of PAMPS as a component of ion conducting sites, the resulting semi-IPN exhibited high proton conductivity (0.1 S cm⁻¹) at 25 °C, which afforded a higher power density of 51 mW cm⁻² at 80 °C. A striking feature is that a long-term initial performance is achieved with a 130 h of stable fuel cell operation in DMFC mode due to effectively suppressed methanol crossover. This is a new record for a fully hydrocarbon membrane in DMFC, seeing that the PVA–PAMPS proton-conducting semi-IPNs are made simply of aliphatic skeletons.     

Kinetic study of low-temperature conversion of plastic mixtures to value added products

Batch-mode pyrolysis of 200.0 g samples of polymers was studied at low temperature. The cracking reaction was carried out in a stainless-steel autoclave with reaction temperatures of 360, 380, 400 and 420 °C, initial pressure of 6.325 kPa (absolute pressure) and reaction times of 0–240 min. Based on the experimental results, a four-lump kinetic model has been developed to describe the production distribution of the light fractions, middle distillates and heavy fraction. This model reasonably fitted the results in each reaction of operation conditions. It was also found that the pyrolysis kinetics of separated plastic, mixed plastic and mixed plastic containing additives can be described by the same kinetic model. The plastic additives have not had a great influence on the product distribution and kinetics of the mixed plastic pyrolysis. Finally, the optimum conditions of low-temperature conversion of plastic mixtures to value-added products were established. The formation of heavy fractions from HDPE was as high as 70 wt% at 380 °C at a reaction time of 250 min. During the thermal degradation of plastic mixtures, the heavy fractions yielded up 50 wt% for 30 min reaction time at 400 °C. The total activation energies for the conversion of HDPE and the plastic mixtures were estimated to be 217.66 kJ mol⁻¹ and 178.49 kJ mol⁻¹, respectively.     

Separation of benzene/cyclohexane mixtures using polyurethane–silica hybrid membranes

Mixed sols were prepared by dissolving polyurethane (a 30 wt% solution in n-propanol, PU) and tetraethylorthosilicate (TEOS) in ethanol at PU:TEOS mass ratios of 1:2, 1:1, 2:1 and 3:1. Each of the sols was coated on a porous α-alumina support tube by the dipping method, and green membranes were heat-treated at 200°C for 1 h in an atmosphere of nitrogen. A PU membrane was also prepared with PU alone. The membranes were 5–6 μm thick. The polyurethane–silica membranes were swollen in benzene but only slightly in cyclohexane at room temperature. The degree of swelling in benzene decreased with increasing fractions of TEOS in the hybrid sols. The selectivity of benzene to cyclohexane was improved due to the suppression of swelling as a result of hybridization with TEOS. The total permeation flux and benzene/cyclohexane selectivity in the membrane prepared with a sol of PU:TEOS=1:1 were 3×10⁻⁵ kg m⁻² s⁻¹ and 19, respectively.     

Copper removal from aqueous solution using biochar: Effect of chemical activation

The main aim of this study was to test the efficiency of biochar for Cu removal from synthetic and soil solutions, respectively.The biochar was produced from brewers draff via pyrolysis. Additionally, the prepared biochar was also activated using 2 M KOH to enhance its sorption efficiency to remove Cu from both solutions. Two different aqueous solutions were prepared for these experiments: (i) a synthetic using Cu-nitrate salt with 0.01 M NaNO₃ and (ii) soil solution obtained from a Cu-contaminated soil using 0.01 M CaCl₂ leaching procedure. Batch sorption and column experiments were used to evaluate the efficiency of both biochar (BC) and activated biochar (BC_act) to remove Cu from the solutions.Results showed that both biochar samples are pure amorphous carbon and the Cu sorption is thus mainly a result of physical sorption on the biochar surface. Next, chemical activation, using 2 M KOH, significantly increased the total volume of all pores in biochar (from 0.01 ± 0.002 to 8.74 ± 0.18 mL g⁻¹). On the other hand, the BET surface area was similar for both sorbents (BC = 9.80 ± 0.62 m² g⁻¹ and BC_act = 11.6 ± 0.4 m² g⁻¹). Results also demonstrate enhanced sorption efficiency of the BC_act (10.3 mg g⁻¹) in comparison with the BC (8.77 mg g⁻¹). Additionally, enhanced Cu removal during column retention test was observed for the BC_act in both synthetic and soil solutions, respectively.In summary, the results showed that biochar prepared from brewers draff was able to remove Cu from both aqueous solutions.     

Platinum nanoparticles supported on nitrobenzene-functionalised graphene nanosheets as electrocatalysts for oxygen reduction reaction in alkaline media

A systematic study on the electrocatalytic properties of Pt nanoparticles supported on nitrobenzene-modified graphene (Pt-NB/G) as catalyst for oxygen reduction reaction (ORR) in alkaline solution was performed. Graphene nanosheets were spontaneously grafted with nitrophenyl groups using 4-nitrobenzenediazonium salt. The electrocatalytic activity towards the ORR and stability of the prepared catalysts in 0.1 M KOH solution have been studied and compared with that of the commercial Pt/C catalyst. The results obtained show that the NB-modified graphene nanosheets can be good Pt catalyst support with high stability and excellent electrocatalytic properties. The specific activity of Pt-NB/G for O₂ reduction was 0.184 mA cm⁻², which is very close to that obtained for commercial 20 wt% Pt/C catalyst (0.214 mA cm⁻²) at 0.9 V vs. RHE. The Pt-NB/G hybrid material promotes a four-electron reduction of oxygen and can be used as a promising cathode catalyst in alkaline fuel cells.     

Dissociation behaviour of (tetra-n-butylammonium bromide + tetra-n-butylammonium chloride) mixed semiclathrate hydrate systems

The thermal properties of {tetra-n-butylammonium bromide + tetra-n-butylammonium chloride (TBAB + TBAC)} mixed semiclathrate hydrates prepared from aqueous solutions were investigated by dissociation temperature measurements and differential scanning calorimetry (DSC). The maximum dissociation temperature of the mixed hydrate crystals at 0.1 MPa is 288.5 K for x_TBAB = 0.2 {mole fraction of TBAB to (TBAB + TBAC)}, which is higher than that of the pure hydrates {T = (285.5 and 288.2) K for TBAB and TBAC hydrates, respectively}. In addition, the dissociation enthalpies of the mixed hydrates are higher than those of the pure hydrates {(5.55 ± 0.06) kJ ⋅ mol⁻¹ H₂O for pure TBAB hydrate and (5.30 ± 0.05) kJ ⋅ mol⁻¹ H₂O for pure TBAC hydrate}, with a maximum of (5.95 ± 0.12) kJ ⋅ mol⁻¹ H₂O recorded at approximately x_TBAB = 0.4. It was therefore suggested that the crystal distortion in (TBAB + TBAC) mixed hydrates, caused by replacing water molecules by both bromide and chloride anions, was smaller than that observed for each pure hydrate. Consequently, the hydration numbers in the mixed hydrates were hypothesized to be slightly higher than those of the pure hydrates.     

Net-structured NiO–C nanocomposite as Li-intercalation electrode material

Net-structured NiO was prepared by urea-mediated homogeneous hydrolysis of Ni(CH₃COO)₂ under microwave radiation followed by a calcination at 500 °C. NiO–C nanocomposite was prepared by dispersing the as-prepared net-structured NiO in glucose solution and subsequent carbonization under hydrothermal conditions at 180 °C. The carbon in the composite was amorphous by the X-ray diffraction (XRD) analysis, and its content was 15.05 wt% calculated according to the energy dispersive X-ray spectroscopy (EDX) result. Transmission electron microscopy (TEM) image of the NiO–C nanocomposite showed that the NiO network was homogeneously filled by amorphous carbon. The reversible capacity of NiO–C nanocomposite after 40 cycles is 429 mAh g⁻¹, much higher than that of NiO (178 mAh g⁻¹). These improvements are attributed to the carbon, which can enhance the conductivity of NiO, suppress the aggregation of active particles, and increase their structure stability during cycling.     

One-step synthesis of hollow structured Si/C composites based on expandable microspheres as anodes for lithium ion batteries

Si/C composites of carbon hollow structures loaded with Si nanoparticles (NPs) (Si/C-HSs) were prepared by one-step pyrolysis of a mixture of Si NPs and expandable microspheres (EMs). For the Si/C-HSs, hollow carbon shells with rough surfaces were formed by directly carbonizing the polymer shells of EMs, and the Si NPs fell into the void space or were loaded on the rough surfaces of the carbon shells. The EM-based carbon shells accommodated the volume expansion of the Si NPs and improved the electrical conductivity of the composites. As a result, the Si/C-HSs exhibited a high capacity (initial reversible capacity: 854.4 mAh g^− 1 at 300 mA g^− 1), stable cycling performance (capacity retention: 80% after 50 cycles), and excellent rate capability.     

Thermodynamics of the solubility of reserpine in {{2-(2-ethoxyethoxy)ethanol + water}} mixed solvent systems at different temperatures

Thermodynamics of solubility of the bioactive compound reserpine in various {2-(2-ethoxyethoxy)ethanol + water} mixed solvent systems was investigated in this study. The solubility of reserpine was determined from T = (298.15 to 338.15) K at atmospheric pressure using the reported method of Higuchi and Connors. Values of the measured solubility of reserpine were correlated with the ideal and Yalkowsky models. The root mean square deviations (RMSD) were observed to be less than 0.020 by an ideal model. However, the RMSD values were observed as less than 0.050 by the Yalkowsky model. The mole fraction solubility of reserpine was observed highest in pure 2-(2-ethoxyethoxy)ethanol (7.69 · 10⁻⁴ at T = 298.15 K) and lowest in pure water (9.71 · 10⁻⁷ at T = 298.15 K) at each temperature investigated. The results of the Van’t Hoff and Krug analysis (thermodynamic studies) indicated endothermic and spontaneous dissolution of reserpine in all {2-(2-ethoxyethoxy)ethanol + water} mixed solvent systems.     

Thermostable ultrafiltration and nanofiltration membranes from sulfonated poly(phthalazinone ether sulfone ketone)

Modification of poly(phthalazinone ether sulfone ketone) (PPESK) by sulfonation with concentrated or fuming sulfuric acid was carried out in order to prepare thermally stable polymers as membrane materials having increased hydrophilicity and potentially improved fouling-resistance. The sulfonated poly(phthalazinone ether sulfone ketone)s (SPPESK) were fabricated into ultrafiltration (UF) and nanofiltration (NF) asymmetric membranes. The effects of SPPESK concentration and the type and concentration of additives in the casting solution on membrane permeation flux and rejection were evaluated by using an orthogonal array experimental design in the separation of polyethyleneglycol (PEG12000 and PEG2000) and Clayton Yellow (CY, MW 695). One UF membrane formulation type had a 98% rejection rate for PEG12000 and a high pure water flux of 867 kg m⁻² h⁻¹. All the NF membranes made in the present study had rejections of ≥96%, and one had a high water flux of 160 kg m⁻² h⁻¹. Several of the NF membrane formulation types had ∼90% rejection for CY. When the membranes were operated at higher temperatures (80°C), the rejection rates declined slightly and pure water flux was increased more than two-fold. Rejection and flux values returned to previous values when the membranes were operated at room temperature again. Mono- and divalent salt rejections and fluxes were studied on an additional NF membrane set.     

Insoluble metal hexacyanoferrates as supercapacitor electrodes

Nano-sized insoluble iron, cobalt and nickel hexacyanoferrates (Mhcf) were prepared by a simple co-precipitation method. The potential of using these materials for supercapacitor was examined by cyclic voltammogram and constant charge/discharge. Due to the different types of the second metal (M), the Mhcf electrodes showed different electrochemical capacitive performances. The specific discharge capacitances of Fehcf, Nihcf and Cohcf electrodes at the current density of 0.2 A g⁻¹ were 425 F g⁻¹, 574.7 F g⁻¹ and 261.56 F g⁻¹, respectively. Meanwhile, the Mhcf electrodes showed good cyclic performance.