Low temperature GaAs grown by gas source molecular beam epitaxy

Low temperature growth of GaAs by gas source molecular beam epitaxy (GSMBE) is investigated. Reflection high energy electron diffraction is used to monitor the low temperature buffer (LTB) growth and anneal conditions. Growth at low temperatures with dimeric arsenic is more sensitive to the V/III flux ratios and substrate temperatures than with As₄ used in solid source MBE. Temperature dependent conductivity and deep level transient spectroscopy measurements are presented to observe trap outdiffusion from the LTB into subsequently grown FET channels. Low temperature photoluminescence spectra show degradation of quantum well properties when LTBs are grown with increasing V/III flux ratios.     

Indium surface segregation in InGaAs-based structures prepared by molecular beam epitaxy and atomic layer molecular beam epitaxy

We present a comparative study on In surface segregation in InGaAs/GaAs structures prepared by molecular beam epitaxy (MBE) and atomic layer MBE (ALMBE) at different growth temperatures. The effect of segregation is evaluated by the energy position of exciton transitions in pseudomorphic 10 ML thick In_xGa_1−xAs/GaAs (0.15≤x≤0.30) and in 1 ML thick InAs/GaAs quantum wells. We show that: (i) In segregation decreases with the growth temperatures and is minimized at ALMBE and MBE growth temperatures lower than 260 and 340°C, respectively, and (ii) the segregation is more effective in ALMBE structures than in the MBE counterparts. The growth conditions that have been singled out allow the preparation of structures with high photoluminescence efficiencies even at the low growth temperatures required to minimize In segregation.     

Se-doped AlGaAs grown on GaAs(111)A by molecular beam epitaxy

The electrical properties of Se-doped Al_0.3Ga_0.7As layers grown by molecular beam epitaxy (MBE) on GaAs(111)A substrates have been investigated by Hall-effect and deep level transient spectroscopy (DLTS) measurements. In Se-doped GaAs layers, the carrier concentration depends on the misorientation angle of the substrates; it decreases drastically on the exact (111)A surface due to the re-evaporation of Se atoms. By contrast, in Se-doped AlGaAs layers, the decrease is not observed even on exact oriented (111)A. This is caused by the suppression of the re-evaporation of Se atoms, by Se---Al bonds formed during the Se-doped AlGaAs growth. An AlGaAs/GaAs high electron mobility transistor (HEMT) structure has been grown. The Hall mobility of the sample on a (111)A 5° off substrate is 5.9×10⁴ cm²/V·s at 77 K. This result shows that using Se as the n-type dopant is effective in fabricating devices on GaAs(111)A.     

Heavily carbon-doped p-type (In)GaAs grown by gas-source molecular beam epitaxy using diiodomethane

Heavily carbon-doped p-type In_xGa_1−xAs (0≤x<0.49) was successfully grown by gas-source molecular beam epitaxy using diiodomethane (CH₂I₂), triethylindium (TEIn), triethylgallium (TEGa) and AsH₃. Hole concentrations as high as 2.1×10²⁰ cm⁻³ were achieved in GaAs at an electrical activation efficiency of 100%. For In_xGa_1−xAs, both the hole and the atomic carbon concentrations gradually decreased as the InAs mole fraction, x, increased from 0.41 to 0.49. Hole concentrations of 5.1×10¹⁸ and 1.5×10¹⁹ cm⁻³ for x = 0.49 and x = 0.41, respectively, were obtained by a preliminary experiment. After post-growth annealing (500°C, 5 min under As₄ pressure), the hole concentration increased to 6.2×10¹⁸ cm⁻³ for x = 0.49, probably due to the activation of hydrogen-passivated carbon accepters.     

Formation and characterization of GaAs/As superlattice grown by molecular beam epitaxy at low substrate temperature

High-resolution X-ray diffractometer and transmission electron microscope (TEM) are used to characterize the redistribution of As precipitates in Si δ-doped GaAs grown by molecular beam epitaxy at low substrate temperature (230°C). The superlattice satellite peaks are observed for samples annealed at 700-800°C for 10 min, which is attributed to the formation of a GaAs/As superlattice during the annealing period. The degree of As precipitates confined on the δ-doped planes is revealed on the intensity of satellite peaks in the X-ray rocking curves, as confirmed by the TEM observations. The lattice expansion and contraction of the annealed low-temperature epitaxial layers can be easily observed from the asymmetry of the satellite peaks.     

The incorporation behavior of arsenic and antimony in GaAsSb/GaAs grown by solid source molecular beam epitaxy

GaAsSb ternary epitaxial layers were grown on GaAs (0 0 1) substrate in various Sb₄/As₂ flux ratios by solid source molecular beam epitaxy. The alloy compositions of GaAs_1−ySb_y were inferred using high-resolution X-ray symmetric (0 0 4) and asymmetric (2 2 4) glance exit diffraction. The non-equilibrium thermodynamic model is used to explain the different incorporation behavior between the Sb₄ and As₂ under the assumption that one incident Sb₄ molecule produces one active Sb₂ molecule. It is inferred that the activation energy of Sb₄ dissociation is about 0.46 eV. The calculated results for the incorporation efficiency of group V are in good agreement with the experimental data.     

MgO films grown on yttria-stabilized zirconia by molecular beam epitaxy

MgO films were grown on (0 0 1) yttria-stabilized zirconia (YSZ) substrates by molecular beam epitaxy (MBE). The crystalline structures of these films were investigated using X-ray diffraction and transmission electron microscopy. Growth temperature was varied from 350 to 550 °C, with crystalline quality being improved at higher temperatures. The MgO films had a domain structure: (1 1 1)[1 1 2¯]_MgO(0 0 1)[1 0 0]_YSZ with four twin variants related by a 90° in-plane rotation about the [1 1 1]_MgO axis. The observed epitaxial orientation was compared to previous reports of films grown by pulsed laser deposition and sputtering and explained as resulting in the lowest interface energy.     

Diffusion of Si-acceptor in δ-doped GaAs grown on GaAs(111)A by molecular beam epitaxy

Diffusion of Si-acceptors (Si occupying As sites) in δ-doped GaAs grown on GaAs(111)A has been investigated by secondary ion mass spectrometry (SIMS). We have measured the diffusion parameters in GaAs(111)A and found that they differ from those in GaAs(001). The diffusion coefficient in GaAs(111)A is smaller than that in GaAs(001) and the activation energy in GaAs(111)A is larger than that in GaAs(001). Furthermore, the diffusion mechanism of Si in GaAs(111)A has been investigated by photoluminescence; we have found that in p-type layers Si-donors (Si occupying Ga sites) diffuse easily to As sites. The activation energy of Si-acceptor diffusion is 2.74±0.11 eV. These results indicate that Si-acceptors are more stable than Si-donors.     

Growth mechanisms of GaAs nanowires by gas source molecular beam epitaxy

GaAs nanowires were grown on GaAs (1 1 1)B substrates in a gas source molecular beam epitaxy system, using self-assembled Au particles with diameters between 20 and 800 nm as catalytic agents. The growth kinetics of the wires was investigated for substrate temperatures between 500 and 600 °C, and V/III flux ratios of 1.5 and 2.3. The broad distribution of Au particles enabled the first observation of two distinct growth regimes related to the size of the catalyst. The origins of this transition are discussed in terms of the various mass transport mechanisms that drive the wire growth. Diffusion of the growth species on the 2-D surface and up the wire sidewalls dominates for catalyst diameters smaller than ∼130 nm on average, while direct impingement on the catalyst followed by bulk diffusion through the Au particle appears to sustain the wire growth for larger catalyst diameters. A change in wire sidewall facets, indicating a probable transition in the crystal structure, is found to be primarily dependent on the V/III flux ratio.     

Optimized InAs quantum effect device structures grown by molecular beam epitaxy

We have investigated InAs quantum effect devices based on both antimonides and arsenides. In an InAs quantum point contact device based on antimonides (InAs/AlGaSb), we have successfully reduced the leakage currents and observed quantum effects at around 77 K by optimizing the heterostructure growth and mesa-etched split-gate approach. Strained InAs quantum dots based on arsenides (AlInAs/AlAs/InAs/InGaAs/AlInAs) were successfully fabricated by MBE growth and mesa-etching. Blue-shifted photoluminescence was obtained from millions of quantum dots with an average lateral size of approximately 2000 å square.     

Anomalous temperature-dependent photoluminescence characteristic of as-grown GaInNAs/GaAs quantum well grown by solid source molecular beam epitaxy

The photoluminescence (PL) mechanisms of as-grown GaInNAs/GaAs quantum well were investigated by temperature-dependent PL measurements. An anomalous two-segmented trend in the PL peak energy vs. temperature curve was observed, which has higher and lower temperature-dependent characteristics at low temperature (5–80 K) and high temperature (above 80 K), respectively. The low and high-temperature segments were fitted with two separate Varshni fitting curves, namely Fit_low and Fit_high, respectively, as the low-temperature PL mechanism is dominated by localized PL transitions while the high-temperature PL mechanism is dominated by the e1–hh1 PL transition. Further investigation of the PL efficiency vs. 1/kT relationship suggests that the main localized state is located at 34 meV below the e1 state. It is also found that the temperature (80 K) at which the PL full-width at half-maximum changes from linear trend to almost constant trend correlates well with the temperature at which the PL peak energy vs. temperature curve changes from Fit_low to Fit_high.     

Improvement of GaInNAsSb films fabricated by atomic hydrogen-assisted molecular beam epitaxy

The effect of incorporation of antimony in GaInNAs films grown by atomic hydrogen-assisted molecular beam epitaxy (MBE) has been investigated. We show that the rate of incorporation of N and In forming GaInNAs do not depend on the Sb beam flux. However, the incorporation of Sb is strongly dependent on the Sb/As₂ flux ratio. Introducing a small amount of Sb (<∼1%) significantly improves the photoluminescence (PL) emission efficiency of GaInNAs, but Sb concentration of >1% rapidly degrades the PL intensity, though a large redshift can still be achieved. Therefore, there is an optimum amount of Sb for the growth of low-strained GaInNAs films to improve the overall optical quality.     

Electrical properties of lateral npn junctions using molecular beam epitaxy grown Si-doped GaAs on patterned substrates

We investigated electrical properties of laterally aligned npn junctions formed with one-step molecular beam epitaxial growth of Si-doped GaAs on patterned substrates. Detailed current-voltage (I-V) measurements of the lateral npn junctions showed asymmetric characteristics which suggest that the junction configuration is rather nn⁻pn with a highly compensated n⁻ region than a simple npn configuration. Temperature dependence of the I-V curves was also examined. Cross-sectional electron beam induced current and transmitted electron microscope measurements revealed the critical angle of the crystal plane at which conduction type of Si-doping converts to be exactly 25°, i.e. (311)A plane.     

p-Type GaAs doped by diiodomethane (CI2H2) in molecular beam epitaxy, metalorganic molecular beam epitaxy, and chemical beam epitaxy

Highly p-type carbon-doped GaAs epitaxial layers were obtained using diiodomethane (CI₂H₂) as a carbon source. In the low 10¹⁹ cm⁻³ range, almost all carbon atoms are electrically activated and at 9×10¹⁹ cm⁻³, 91% are activated. The carbon incorporation efficiency in GaAs layers grown by metalorganic molecular beam epitaxy (MBE) and chemical beam epitaxy (CBE) is lower than that by MBE due to the site-blocking effect of the triethylgallium molecules. In addition, in CBE of GaAs using tris-dimethylaminoarsenic (TDMAAs), the carbon incorporation is further reduced, but it can be increased by cracking TDMAAs. Annealing studies indicate no hydrogenation effect.     

Effect of atomic hydrogen in highly lattice-mismatched molecular beam epitaxy

Effects of atomic hydrogen on the growth of lattice-mismatched InAs/GaAs and GaAs/InP systems have been investigated. The irradiation of atomic H has resulted in a delay of the onset of formation of three-dimensional islands maintaining flat surface morphology and increase of the critical layer thickness (CLT) from 4 to 10 å in the case of the InAs/GaAs system. The effect of atomic H was shown to be dependent on the growth conditions such as the growth temperature and V/III flux ratio. The increase of CLT with atomic H irradiation may be explained by the uniform distribution of the total misfit stress in the plane of the surface as a result of enhanced two-dimensional growth by atomic H acting as a surfactant.     

Carbon doping into GaAs using combined ion beam and molecular beam epitaxy method

Carbon (C) doping by combined ion beam and molecular beam epitaxy (CIBMBE) was investigated. In this technique, mass-analyzed C ions (¹²C⁺) are accelerated at low energies of 30 to 1000 eV and are irradiated onto growing GaAs substrate. Doping concentration control in CIBMBE can be very stably accomplished by simply adjusting the ion beam current density, which is independent of growth conditions of host materials. Experiments on systematic variation of C⁺ ion acceleration energy (E_C+) indicated that, in the energy range of E_C+<170 eV, net hole concentration (|N_A-N_D|) increases slightly as E_C+ increases. The highest |N_A-N_D| is obtained at E_C+ = 170 eV under the constant C⁺ ion beam current density. For E_C+>170 eV, |N_A-N_D| decreases dramatically with increasing E_C+, which can be explained in terms of enhanced sputtering effect. Although no evidence of damages induced by ion irradiation is shown for low E_C+ range of ≤170 eV, trace of damages is apparently observed for E_C+>170 eV.     

InGaAsP/InP multiple quantum wells grown by gas-source molecular beam epitaxy

We have grown In₁-_xGa_xAs_yP₁-_y/InP multiple quantum well structures with 1.3 μm excitonic absorption at room temperature by gas-source molecular beam epitaxy. In-situ composition determination in GaAs₁-_xP_x and InAs_xP₁-_x was carried out by measuring group-V-induced intensity oscillations of reflection high-energy electron diffraction. Based on the in-situ composition calibration for these ternary end members, Ga and As compositions in the quaternary compound, In₁-_xGa_xAs_yP₁-_y, were controlled successfully. Measurements by X-ray rocking curve, low-temperature photoluminescence and absorption spectroscopy indicate that high-quality In₁-_xGa_xAs_yP₁-_y/InP multiple quantum well samples were obtained.     

High-quality InP grown by chemical beam epitaxy

InP films were grown by chemical beam epitaxy using trimethylindium (TMI) and pure phosphine (PH₃) in a flow control mode with hydrogen as the carrier gas, with the TMI flow rate fixed at 3 SCCM. Substrate temperatures were varied between 505 and 580°C and V/III ratios from 3 to 9. InP layers with high optical quality (intense and narrow excitonic transition lines) and high crystalline quality (narrow and symmetric X-ray diffraction peaks) could be grown only within a narrow parameter window around a substrate temperature of 545°C (δT_s ≤ 25°C) and a V/III ratio of 5.5 (δ(V/III) ≤ 2). Carrier densities of 8 × 10¹⁴ cm^-3 with mobilities of 70000 cm²/V.s measured at 77 K were obtained for growth conditions close to the edge of this parameter window towards low V/III ratios. The growth rate of inP was also clearly at its maximum in the given parameter window. Leaving the window, by changing either the growth temperature or the V/III ratio, significantly decreased the growth rate. This reduced growth rate was accompanied by a degradation in the crystalline quality. We also demonstrate that for higher TMI flow the parameter window shifts to higher growth temperatures. The InP could be doped effectively with Si in the range from 9 × 10¹⁵ to 3 × 10¹⁸ cm^-3.     

Stability of GaAs oxide under metalorganic molecular beam epitaxy process

Well-defined oxide of GaAs can be used as a mask material for selective-area metalorganic molecular beam epitaxy (MOMBE) of GaAs. In this study, the reaction between triethylgallium (TEG) and the GaAs oxide layer was studied using a quadrupole mass spectrometer (QMS) and an atomic force microscope (AFM). Results of the QMS observation showed that TEG was reflected on the GaAs oxide surface until the start of desorption of the GaAs oxide, and the GaAs oxide layer was desorbed from the wafer after a large time delay from the start of TEG supply. AFM images showed that many holes appeared on the GaAs oxide surface during the desorption of the GaAs oxide. The effect of incident TEG upon the stability of the GaAs oxide mask is discussed.