Sheath and electron density dynamics in the normal and self-pulsing regime of a micro hollow cathode discharge in argon gas

A microplasma is generated in the microhole (400 μm diameter) of a molybdenum-alumina-molybdenum sandwich (MHCD type) at medium pressure (30–200 Torr) in pure argon. Imaging and emission spectroscopy have been used to study the sheath and electron density dynamics during the stationary normal regime and the self-pulsing regime. Firstly, the evolution of the microdischarge structure is studied by recording the emission intensity of the Ar (5p[3/2]₁–4s[3/2]₁)_{1}) line at 427.217 nm, and Ar⁺ (4p′ ²P_3/2–4s′ ²D_5/2)_{5/2}) line at 427.752 nm. The maximum of the Ar⁺ line is located in the vicinity of the sheath-plasma edge. In both regimes, the experimental observations are consistent with the position of the sheath edge calculated with an ionizing sheath model. Secondly, the electron density is recorded by monitoring the Stark broadening of the H_b_\beta-line. In the self-pulsing regime at 150 Torr, the electron density reaches its maximum value of 4 × 10¹⁵ cm^-3, a few tens of ns later than the discharge current maximum. The electron density then decays with a characteristic decay time of about 2 μs, while the discharge current vanishes twice faster. The electron density in the steady-state regime is two orders of magnitude lower, at about 6–8 × 10¹³ cm^-3.     

Improved electrical properties of HfTiO/GeO x N y gate dielectric Ge MOS capacitors by using wet–NO Ge-surface pretreatment

Reactive cosputtering is employed to prepare high-permittivity HfTiO gate dielectric on n-Ge substrate. Effects of Ge-surface pretreatment on the interface and gate leakage properties of the dielectric are investigated. Excellent performances of Al/HfTiO/GeO _x N _y /n-Ge MOS capacitor with wet–NO surface pretreatment have been achieved with a interface-state density of 2.1×10¹¹ eV⁻¹ cm⁻², equivalent oxide charge of −7.67×10¹¹ cm⁻² and gate leakage current density of 4.97×10⁻⁵ A/cm² at V _g =1 V.     

First comparison of electric field induced second harmonic of near-infrared femtosecond laser pulses in reflection and transmission generated from Si/SiO<Subscript>2</Subscript> interfaces of a silicon membrane

For the first time electric field induced second harmonic (EFISH) generation of femtosecond (fs) laser pulses (λ=800 nm, τ=75±5 fs, rep. rate=80 MHz, E _pulse≤10 nJ) is observed in transmission through a thin free-standing silicon (Si) membrane of 10-μm thickness and compared to the well-known EFISH results in reflection by use of the z-scan technique. EFISH in reflection and transmission unequivocally originate from the front and rear Si/SiO₂ interfaces, respectively, with SiO₂ being the natural oxide on the Si surfaces. Frequency conversion is enhanced by photoinduced electric fields across the Si/SiO₂ interfaces caused by charge-carrier injection from Si into the oxide. The z-scan results and time-dependent measurements allow comparison of the EFISH signal amplitudes and time constants detected in transmission and reflection, demonstrating the need for further investigation.     

Gelatin-based protonic electrolyte for electrochromic windows

Proton-conducting gel polymer electrolytes based on gelatin plasticized with glycerol and containing acetic acid were investigated, characterized, and applied to electrochromic window. For glycerol contents varying from 7% to 48%, the conductivity of the uniform and predominantly amorphous gel electrolyte was found to follow a Vogel–Tamman–Fulcher behavior with the temperature. Typically, for the electrolyte chosen to make 7 × 2 cm² electrochromic smart window with the configuration: glass/fluor-doped tin oxide (FTO)/WO₃/gelatin electrolyte/CeO₂–TiO₂/FTO/glass and containing 28% of glycerol, the conductivities were found to be of the order of 5 × 10⁻⁵ S/cm at room temperature and 3.6 × 10⁻⁴ S/cm at 80 °C. The device was characterized by spectroelectrochemical techniques and was tested up to 10,000 cycles showing a fast coloring/bleaching behavior, where the coloring process was achieved in 10 s and the bleaching in 2 s. The transmission variation at the wavelength of 550 nm was about 15%. The cyclic voltammograms showed a very good reversibility of the cathodic/anodic processes, and the charge density was about 3.5 mC/cm². The memory tests showed that the transmittance in the colored state increased by 8% in 90 min after removing the potential.     

Facile synthesis and phase control of copper chalcogenides with different morphologies

A series of stoichiometric and nonstoichiometric copper–chalcogenide nanocrystallines with different morphologies, e.g., extremely high aspect ratio nanofibers (Cu₉S₈), tubular structure (Cu _x S (x=∼1.86–1.96), nanorods (CuS, Cu₃₁S₁₆), platelets (β-CuSe, Cu₃Se₂), rope-like Cu₃Se₂, as well as spherical nanoparticles (Cu₇Se₄, Cu_2−x Se), have been successfully synthesized in 20 vol% water and 80 vol% organic solvents mixture under mild conditions. The products were characterized by various techniques, including X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), electronic diffraction (ED), and high-resolution transmission electron microscopy (HRTEM). The studies of the optical properties revealed that the copper chalcogenides have a wide absorption in the range of about 400–700 nm, with accessional IR band. Systematic studies showed that the mixture of 20 vol% water and 80 vol% organic solvents played a key role in controlling the copper chalcogenides with different morphologies and phases.     

Synthesis of SmAlO<Subscript>3</Subscript> nanocrystalline powders by polymeric precursor method

SmAlO₃ nanocrystalline powders were successfully synthesized by the polymeric precursor method using ethylenediaminetetraacetic acid as a chelating agent. The precursor and the derived powders were characterized by thermogravimetry analysis (TG) and differential scanning calorimetry analysis (DSC), infrared spectroscopy (IR), X-ray diffractometry (XRD) and transmission electron microscopy (TEM). The results showed that pure SmAlO₃ powder with orthorhombic perovskite structure could be synthesized at 800°C for 2 h without formation of any intermediate phase. The average particle size of the powder synthesized at 900°C was as low as 28 nm. Subsequently, the bulk SmAlO₃ ceramics were prepared at various sintering temperatures using the synthesized powders calcined at 900°C for 2 h as starting materials. The sintering experiments indicated that the sample sintered at 1550°C for 2 h exhibited the highest relative density of 97.2% and possessed the best microwave dielectric properties of ε _r=20.94, Q×f=78600 GHz and τ _f=−71.8 ppm/°C.     

TiO<Subscript>2</Subscript> nanotube height effect on the efficiency of dye-sensitized solar cells

Performance of dye-sensitized solar cells (DSSCs) based on TiO₂ nanotubes (NTs) filled with TiO₂ nanoparticles (NPs) was studied as a function of NT height (h). The NT height was varied in the range of 1.5–7.0 μm, while the NT diameter was kept constant at ~80 nm. The studies showed that DSSC efficiency, current density, and fill factor linearly increased with h and ranged in 1.76–6.5%, 3.62–13.2 mA/cm², and 0.66–0.76, respectively, within the h range studied. The electrochemical impedance spectroscopy was also performed to study DSSC electron transport properties. Based on both photovoltaic and electrochemical impedance spectroscopy data, the results were explained as being due to the increased dye loading that led to higher light-harvesting efficiency.     

Photoluminescence properties of Eu3+-doped Cd1−x Zn x S quantum dots

Eu³⁺-doped Cd_1−x Zn _x S (0 ≤ x ≤ 0.5) quantum dots (QDs) have been synthesized using wet chemical precipitation method. X-ray diffraction and transmission electron microscope have been used for the crystallographic and morphological characterization of synthesized nanomaterials. In order to understand the spectral characteristics of doped QDs, N₂-laser induced time resolved spectra have been recorded. Excited state lifetime values for dichromatic emission (red and violet) attributed to ⁵D₀ → ⁷F_J (J = 1, 2) transitions of Eu³⁺ and host lattice transitions have been calculated from the recorded luminescence decay curves. Decay time dependence on the dopant concentration (0.01–10 at. wt% of Cd²⁺) has been studied in detail.     

NO2 sensing properties of YSZ-based sensor using NiO and Cr-doped NiO sensing electrodes at high temperature

Nickel oxide and chromium-doped nickel oxide (Ni_0.95Cr_0.03O_1−δ ) were prepared by thermal decomposition of nitrates. The obtained NiO and Ni_0.95Cr_0.03O_1−δ samples were utilized as sensing electrodes (SEs) in yttria-stabilized zirconia (YSZ)-based sensors for detection of NO₂ at 800 °C under wet condition (5 vol.% H₂O). While the mixed-potential-type planar sensor attached with NiO-SE gave rather large NO₂ sensitivity, the sensor attached with Ni_0.95Cr_0.03O_1−δ -SE exhibited fast recovery rate with an acceptable sensitivity. The Δemf (electromotive force) of the sensors varied linearly with NO₂ concentration in the examined range of 50–400 ppm on a logarithmic scale. Based on the results of measurements for polarization, complex impedance and gas phase catalysis, the fast recovery was attributable to the high rate for the anodic reaction of O₂ at the Ni_0.95Cr_0.03O_1−δ /YSZ interface, and the lower NO₂ sensitivity was caused by both the high rate for the anodic reaction of O₂ and the high degree for the gas phase conversion of NO₂ to NO.     

Plasma-filled rippled wall rectangular backward wave oscillator driven by sheet electron beam

Performance of the backward wave oscillator (BWO) is greatly enhanced with the introduction of plasma. Linear theory of the dispersion relation and the growth rate have been derived and analysed numerically for plasma-filled rippled wall rectangular waveguide driven by sheet electron beam. To see the effect of plasma on the TM₀₁ cold wave structure mode and on the generated frequency, the parameters used are: relativistic factor γ = 1.5 (i.e. v/c = 0.741), average waveguide height y ₀ = 1.445 cm, axial corrugation period z ₀ = 1.67 cm, and corrugation amplitude ε = 0.225 cm. The plasma density is varied from zero to 2 ×10¹² cm^− 3. The presence of plasma tends to raise the TM₀₁ mode cut-off frequency (14 GHz at 2 ×10¹² cm^− 3 plasma density) relative to the vacuum cut-off frequency (5 GHz) which also causes a decrease in the group velocity everywhere, resulting in a flattening of the dispersion relation. With the introduction of plasma, an enhancement in absolute instability was observed.     

Time-resolved time-dependent photo-acoustic spectroscopy of NO2 in a high frequency multi-resonant cavity

The paper reports the pulsed laser-based time-resolved time-dependent Photo-acoustic (PA) spectroscopy of NO₂ gas in a specially designed multi mode-Resonant PA Cell which is made of Stainless Steel and has a “Q” value of the order of 79. Furthermore the designed cell allows us to excite some of the longitudinal, radial and azimuthal resonance modes of the photo-acoustic signals simultaneously in a very efficient manner. The presence of many newly excited modes occur at 7050 Hz, 10350 Hz and 14650 Hz frequencies is observed for the first time in NO₂ at room temperature. These results are obtained by employing second harmonics i.e. λ=532 nm pulses from Q-switched Nd:YAG laser having 7 ns pulse duration. Some of the new acoustic spectrum lines at higher frequencies are recorded between 0.5–10 ms data acquisition time, which also extends the frequency monitoring range of our system. The study also highlights some of the important aspects such as the decaying behavior of some of these resonant acoustic spectrum lines occur on the expense of others as well as the saturation behavior of some other modes in the NO₂ gas sample. The estimated low level detection limit of NO₂ buffered in air is of the order of 17.9 ppbV.     

Table-top kHz hard X-ray source with ultrashort pulse duration for time-resolved X-ray diffraction

The interaction of ultrashort laser pulses with solid state targets is studied concerning the production of short X-ray pulses with photon energies up to about 10 keV. The influence of various parameters such as pulse energy, repetition rate of the laser system, focusing conditions, the application of prepulses, and the chirp of the laser pulses on the efficiency of this highly nonlinear process is examined. In order to increase the X-ray flux, the laser pulse energy is increased by a 2nd multipass amplifier from 750 μJ to 5 mJ. By applying up to 4 mJ of the pulse energy a X-ray flux of 4×10¹⁰ Fe K _α photons/s or 2.75×10¹⁰ Cu K _α photons/s are generated. The energy conversion efficiency is therefore calculated to η _Fe≈1.4×10⁻⁵ and η _Cu≈1.0×10⁻⁵. The X-ray source size is determined to 15×25 μm². By focusing the produced X-rays using a toroidally bent crystal a quasi-monochromatic X-ray point source with a diameter of 56 μm×70μm is produced containing ≈10⁴ Fe K _α1 photons/s which permits the investigation of lattice dynamics on a picosecond or even sub-picosecond time scale. The lattice movement of a GaAs(111) crystal is shown as a typical application.     

Numerical simulation of ultra-broadband phase-sensitive optical parametric amplification of image

The ultra-broadband phase-sensitive optical parametric amplification and de-amplification of image in a BBO nonlinear crystal with type I phase-matching are theoretically investigated. Amplified images with a gain of 10⁸ and a bandwidth as broad as 420 nm are realized using a 25 GW/cm ⁻² peak pump-power density with 1.125 ps chirped-pulse duration. The spatial resolution after optical parametric amplification is estimated to be q ₀ =200 rad/mm (i.e., 31.8 lines/mm), which corresponds to the size of the minimum resolvable feature of the amplified image ~5 μm.     

Impact of ethylene carbonate on electrical properties of PVA/(NH4)2SO4/H2SO4 proton-conductive membrane

A new proton-conductive membrane (PCM) based on poly (vinyl alcohol) and ammonium sulfate (NH₄)₂SO₄ complexed with sulfuric acid and plasticized with ethylene carbonate (EC) at different weight percent were prepared by casting technique. The structural properties of these electrolyte films were examined by XRD studies. The XRD patterns of all the prepared polymer electrolytes reveal the amorphous nature of the films. ac conductivity and dielectric spectra of the electrolyte were studied with changing EC content from weight 0.00 to 0.75 g. A maximum conductivity of 7.3 × 10⁻⁵ S cm⁻¹ has been achieved at ambient temperature for PCM containing 0.25 g of ethylene carbonate. The electrical conductivity σ, dielectric constant ε′ and dielectric loss ε″ of PCM in frequency range (100 Hz to 100 KHz), and temperature range (300–400 K) were carried out. Measurement of transference number was carried out to investigate the nature of charge transport in these polymer electrolyte films using Wagner’s polarization technique. Transport number data showed that the charge transport in these polymer electrolyte systems was predominantly due to ions. The electrolyte with the highest electrical conductivity was used in the fabrication of a solid-state electrochemical cell with the configuration (Mg/PCM/PbO₂). Various cell parameters ldensity, and current density were determined. The fabricated cells gave capacity of 650 μAh and have an internal resistance of 11.6 kΩ.     

Pressure-induced amorphization of Gd2(MoO4)3: A high pressure Raman investigation

High pressure Raman spectroscopic studies on Gd₂(MoO₄)₃(GMO) have been carried out at ambient temperature in the diamond cell to 10 GPa hydrostatic pressure. These experiments have revealed pressure-induced phase transitions in GMO near 2 GPa and 6.0 GPa. The first transition is from Pba2(β′) phase to another undetermined crystalline phase, designated as phase II, and the second transition is to an amorphized state. On releasing pressure there is a partial reversion to the crystalline state. The Raman data indicate that the amorphization is due to disordering of the MoO₄ tetrahedral units. Further, it is inferred from the nature of the Raman bands in the amorphized material that the Mo-O bond lengths and bond angles have a range of values, instead of a few set values. The results of the present study as well as previous high pressure-high temperature quenching experiments strongly support that pressure-induced amorphization in GMO is a consequence of the kinetically impededβ toα phase transition. The system in frustration becomes disordered. The rare earth trimolybdates crystallizing in theβ′ structure are all expected to undergo similar pressure-induced amorphization.     

Magnetic properties of the ordered and disordered double perovskite Sr<Subscript>2</Subscript>Fe<Subscript>1+x</Subscript>Mo<Subscript>1−x</Subscript>O<Subscript>6</Subscript> (−1 ≤ x ≤ 1/3)

We have studied the effect of cationic disorder on the spin polarization of the double perovskite system Sr₂Fe_1+x Mo_1−x O₆ with  −1 ≤ x ≤ 1/3. The composition x = 0 corresponds to the well-known double-perovskite Sr₂FeMoO₆, which is expected to have complete spin polarization, however all samples present some degree of Fe/Mo disorder which reduces the tunneling magnetoresistance in granular samples. We consider an electronic model within the renormalized perturbation expansion Green’s functions, consisting in a correlated electron picture with localized Fe-ions and itinerant electrons interacting with the local spins via a double-exchange type mechanism. Our results show the influence of disorder on the density of states and the ground-state properties, particularly on the spin polarization over the whole range of x.     

A dual resonance model for high energy electroweak reactions

We derive a dual resonance model for two body electroweak reactions at a few TeV. This model depends on one non standard free parameter, the “weak interaction Regge slope”α _w ^′ , and implies towers of resonances in all non-exotic channels at massesm _n=√n/α _w ^′ . Whenα _w ^′ goes to zero, we require, by explicit matching, consistency of our model at the tree level with the standard model with Higgs boson graphs removed. To derive this model, we have transposed in the electroweak domain an equivalent model suited to hadronic interactions at a few GeV which gives a good agreement with experimental data. This article was processed by the author using the LAT_EX style filepljour2 from Springer-Verlag.     

Microwave-assisted rapid synthesis of Ag nanoparticles/graphene nanosheet composites and their application for hydrogen peroxide detection

Abstract  

Ag nanoparticles/graphene nanosheet (AgNPs/GN) composites have been rapidly prepared by a one-pot microwave-assisted reduction method, carried out by microwave irradiation of a N,N-dimethylformamide (DMF) solution of graphene oxide (GO) and AgNO₃. Several analytical techniques including UV–vis spectroscopy, FT-IR spectroscopy, Raman spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM) have been used to characterize the resulting AgNPs/GN composites. It suggests that such composites exhibit good catalytic activity toward reduction of hydrogen peroxide (H₂O₂), leading to a H₂O₂ sensor with a fast amperometric response time of less than 2 s. The linear detection range is estimated to be from 0.1 to 100 mM (r = 0.999), and the detection limit is estimated to be 0.5 μM at a signal-to-noise ratio of 3.     

Preparation and electrochemical properties of nano Al<Subscript>0.2</Subscript>V<Subscript>2</Subscript>O<Subscript>5.3−<Emphasis Type="BoldItalic">δ</Emphasis></Subscript> cathode materials for rechargeable lithium batteries

Nano-sized Al³⁺-doped V₂O₅ cathode materials, Al_0.2V₂O_5.3−δ , were prepared by an oxalic acid assisted sol–gel method at 350 °C (sample A) and 400 °C (sample B). X-ray diffraction confirmed that samples A and B were pure phase Al_0.2V₂O_5.3−δ with an orthorhombic structure close to that of V₂O₅. Scanning electron microscopy showed that sample A was in nanoscale with a mean particle size about 50 nm. Cyclic voltammetry showed the good electrochemical and structural reversibility of the Al_0.2V₂O_5.3−δ nanoparticles during the Li⁺ insertion/extraction process. The Al_0.2V₂O_5.3−δ nanoparticles exhibited excellent charge–discharge cycling performance and rate capability compared to that of bulky V₂O₅ electrodes. For instance, the materials delivered a reversible specific capacity about 180 mAh g⁻¹ (sample A) and 150 mAh g⁻¹ (sample B), in the potential window of 4.0–2.0 V at the current density of 150 mA g⁻¹. The Al_0.2V₂O_5.3−δ nanoparticles in particular showed almost no capacity fading for at least 50 cycles.     

Self-assembly of boehmite nanopetals to form 3D high surface area nanoarchitectures

A flower-like boehmite nanostructure was prepared through a template-free chemical route by the self-assembly process of nanosize petals 800–1000 nm long, 200–250 nm wide, 20–50 nm thick and having an average crystallite size of about 2.21 nm. X-ray diffraction analysis (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), DTA/TGA analyses and Brunauer–Emmet–Teller (BET-N₂) analyses were used in order to characterize the product obtained. XRD results exhibited that the obtained nanostructures composed of pure orthorhombic AlOOH phase. The effects of Cl⁻ ions and TEA on the growth of boehmite three-dimensional nanoarchitectures in the presence of NO₃^-\mathrm{NO}_{3}^{-} ions were investigated. BET analyses of as-prepared material demonstrate that this nanostructure material has a high specific surface area, as high as 123 m² g⁻¹.