Simultaneous determination of econazole nitrate, main impurities and preservatives in cream formulation by high performance liquid chromatography

A reversed-phase high performance liquid chromatographic (RP-HPLC) method for determination of econazole nitrate, preservatives (methylparaben and propylparaben) and its main impurities (4-chlorobenzyl alcohol and alpha-(2,4-dichlorophenyl)-1H-imidazole-1-ethanol) in cream formulations, has been developed and validated. Separation was achieved on a column Bondclone^® C18 (300 mm × 3.9 mm i.d., 10 μm) using a gradient method with mobile phase composed of methanol and water. The flow rate was 1.4 mL min⁻¹, temperature of the column was 25 °C and the detection was made at 220 nm. Miconazole nitrate was used as an internal standard. The total run time was less than 15 min. The analytical curves presented coefficient of correlation upper to 0.99 and detection and quantitation limits were calculated for all molecules. Excellent accuracy and precision were obtained for econazole nitrate. Recoveries varied from 97.9 to 102.3% and intra- and inter-day precisions, calculated as relative standard deviation (R.S.D.), were lower than 2.2%. Specificity, robustness and assay for econazole nitrate were also determined. The method allowed the quantitative determination of econazole nitrate, its impurities and preservatives and could be applied as a stability-indicating method for econazole nitrate in cream formulations.     

Capillary zone electrophoresis method for the determination of famotidine and related impurities in pharmaceuticals

A simple and rapid capillary zone electrophoresis (CZE) method with UV detection has been developed for the determination of famotidine and its potential impurities in pharmaceutical formulations. The electrophoretic separation of these compounds was performed using a fused silica capillary and 37.5mmolL(-1) phosphate buffer pH 3.5 as the electrolyte. Under the optimised conditions, six impurities could be resolved from the famotidine peak in less than 7min. The calibration curves obtained for the seven compounds were linear over the concentration range investigated (from 1.5 to 78.5microg mL(-1)). The intra- and inter-day relative standard deviations for the migration times and corrected peak areas were less than 2% and 5%, respectively. The detection limits were found to be 0.09microg mL(-1) for famotidine, and from 0.1 to 0.62microg mL(-1) depending on the impurities. The method has been successfully applied to the determination of famotidine in commercial dosage forms.     

Quantification of buserelin in a pharmaceutical product by multiple-injection CZE

An efficient and rapid separation method based on reversed-polarity multiple-injection CZE (MICZE), has been developed for the quantification of buserelin in a pharmaceutical product. The determinations were performed by serially injecting five standard solutions of buserelin (50-300 microg/mL) and one reference analyte into a Polybrene-coated capillary. All the samples contained goserelin, an analog peptide to buserelin, as internal standard (IS). Immediately after pressure injection, the applied sample plugs were subjected to electrophoresis for 2 min at -25 kV. Consequently, each sample plug became isolated from its neighboring plugs by the BGE, composed of 100 mM phosphate-triethanolamine buffer at pH 3.0 containing 10% v/v ACN. During separation the individual sample components migrated at similar velocities and as distinct zones through the capillary giving 24 peaks, 12 from the analyte and the IS and 12 from the sample matrix. The buserelin content of the pharmaceutical product was determined to be 0.94 +/- 0.05 mg/mL, which is only a slight deviation from the declared concentration (1 mg/mL).     

Validation of a capillary zone electrophoresis method for the comparative determination of etoricoxib in pharmaceutical formulations

A CZE method was developed and validated for the analysis of etoricoxib in pharmaceutical dosage forms, using prilocaine as an internal standard. The CZE method was carried out on a fused-silica capillary (50 microm id, effective length 40 cm). The BGE consisted of 25 mM tris-phosphate solution at pH 2.5. The capillary temperature was maintained at 35 degrees C, the applied voltage was 25 kV, the injection was performed using the pressure mode at 50 mbar for 5 s, with detection at 234 nm using a photodiode array detector. The method was linear in the range of 2-150 microg/mL (r(2) = 0.9999). The specificity and stability-indicating capability were proven through the degradation studies and showing also that there was no interference of the excipients of the formulation. The accuracy was 99.49% with RSD of 0.66%. The limits of quantitation and detection were 2 and 0.58 microg/mL, respectively. Moreover, method validation demonstrated acceptable results for the precision, sensitivity, and robustness. The proposed method was successfully applied for the quantitative analysis of etoricoxib pharmaceutical formulations, and the results compared to the HPLC and LC-MS/MS methods, showing nonsignificant difference (p >0.05).     

Novel polymer monolith microextraction using a poly(methacrylic acid-ethylene glycol dimethacrylate) monolith and its application to simultaneous analysis of several angiotensin II receptor antagonists in human urine by capillary zone electrophoresis

Novel polymer monolith microextraction (PMME) using a poly(methacrylic acid-ethylene glycol dimethacrylate) (poly(MAA-EGDMA)) monolith in conjunction with capillary zone electrophoresis (CZE) was developed for the determination of several angiotensin II receptor antagonists (ARA-IIs) in human urine. The extraction device consisted of a regular plastic syringe (1 mL), a poly(MAA-EGDMA) monolithic capillary (2 cm x 530 microm I.D.) and a plastic pinhead connecting the former two components seamlessly. The extraction was achieved by driving the sample solution through the monolithic capillary tube using a syringe infusion pump, and for the desorption step, an aliquot of organic solvent was injected via the monolithic capillary and collected into a vial for subsequent analysis by CZE. The best separation was realized at 25 kV using a buffer that consisted of 50% acetonitrile and 50% buffer solution (v/v) containing 10 mM disodium hydrogenphosphate (adjusted to pH 2.3 with 1M hydrochloric acid). The method was successfully applied to the determination of telmisartan (T), irbesartan (I) and losartan (L) in urine samples with candesartan (C) as internal standard, yielding the detection limit of 15-20 ng/mL. Close correlation coefficients (R>0.999) and excellent method reproducibility were obtained for all the analytes over a linear range of 0.08-3 microg/mL.     

Optimum conditions for effective use of the terminating ion in transient isotachophoresis for capillary zone electrophoretic determination of nitrite and nitrate in seawater,with artificial seawater as background electrolyte

We have examined transient isotachophoresis (ITP) conditions, e.g. the nature of the terminating ion, its concentration, and the injection procedure, to improve the limit of detection (LOD) for determination of nitrite and nitrate in seawater by capillary zone electrophoresis (CZE). Artificial seawater containing 3.0 mmol L(-1) cetyltrimethylammonium chloride (CTAC) was used as background electrolyte (BGE). After sample injection 600 mmol L(-1) acetate was separately injected into the capillary as the terminating ion for transient ITP. The LOD for nitrite and nitrate, obtained at a signal-to-noise ratio (S/N) of 3, were 15 and 7.0 microg L(-1) (as nitrogen), respectively. Relative standard deviations (RSD) of peak area for nitrite and nitrate were 7.3 and 0.8%, respectively, and the RSD of peak height were 5.7 and 1.2%, respectively, when the concentrations of nitrite and nitrate were 0.05 and 0.25 mg L(-1). The RSD of migration time for these ions was 0.2%. The proposed method was applied to the determination of nitrite and nitrate in seawater samples. The results for nitrite were nearly in agreement with those obtained by naphthylethylenediamine spectrophotometric analysis (SPA; correlation coefficient 0.9041).     

Separation efficiency in protein zone electrophoresis performed in capillaries of different diameters

R-phycoerythrin (PHYCO, Mr 240 000), glucose-6-phosphate dehydrogenase (GPD, Mr 104 000) and two charge isomers of recombinant green fluorescent protein (GFP-1 and GFP-2, Mr 27 000) were subjected to capillary zone electrophoresis (CZE) in capillaries of 50, 100 and 150 microm inner diameter at various sample concentrations, electric field strengths, and lengths of the initial zone with the purpose of testing the hypothesis that protein - capillary wall interactions rather than thermal effects are predominantly responsible for the peak spreading of proteins in CZE. The efficiency of CZE was expressed in terms of the number of theoretical plates, N, or the plate height corrected by subtracting the contribution from initial zone length, H'. The latter has the advantage of solely reflecting contributions to the separation efficiency arising from intracolumn peak spreading in capillaries of different diameters. The separation efficiency measured varied widely, by two orders of magnitude, for these proteins under identical conditions, with GPD exhibiting the highest and PHYCO the lowest values of N. H' was found to be independent of sample concentrations within the concentration ranges studied, 1-100 microg/mL for PHYCO and 100-1000 microg/mL for GPD, while exhibiting a decrease with sample concentration for GFP, especially in 150 microm diameter capillaries, within the concentration range 1-100 microg/mL. H'was also found to be independent of electric field strength up to 300-400 V/cm for PHYCO and GFP. In all experiments, the CZE of proteins in 100 microm diameter capillaries provided a higher or, at least, equal efficiency, compared to that in 50 or 150 microm diameter capillaries. It may be concluded that the protein - capillary wall interactions and protein microheterogeneity are the dominant sources of peak spreading and their specific combinations are thought to be responsible for the wide variation in separation efficiency between proteins in CZE observed under identical conditions.     

Determination of nitrate in seawater by capillary zone electrophoresis with chloride-induced sample self-stacking

A capillary zone electrophoresis (CZE) method was established to determine low concentration nitrate which was online preconcentrated with chloride-induced leading-type sample self-stacking for seawater samples. The sample self-stacking was based on transient isotachophoresis in which chloride served as leading ion, and dihydrogenphosphate in the background electrolyte (0.1 M phosphate) as the terminating one. Due to the small mobility difference between nitrate and chloride, the isotachophoresis time was so long that nitrate could not separate from the rear sharp boundary between chloride and the background electrolyte (BGE) when it migrated to the detection window. A zwitterionic surfactant, 3-(N,N-dimethyldodecylammonio)propane sulfonate was added to the BGE to enlarge the mobility difference for its selective interaction with anions. Thus, a highly conductive sample could be injected in a large volume with about fourfold sensitivity enhancement compared to that of field amplification sample stacking in which nitrate was dissolved in pure water. The relative standard deviations (n=5) of migration time, peak area, peak height were 0.1, 3.0, 1.5%, respectively. The limit of detection (S/N=3) for nitrate was 35 microg/l in seawater samples with relatively low concentration BGE (0.1 M sodium phosphate, pH 6.2). The overall procedure consisting of online preconcentration and separation was as simple as routine CZE except for a slightly longer sample injection time (3-4 min).     

Development of capillary zone electrophoresis-electrospray ionization-mass spectrometry for the determination of lamotrigine in human plasma

A method of coupling capillary zone electrophoresis (CZE) with electrospray ionization-mass spectrometry (ESI-MS) detection has been developed for monitoring an antiepileptic drug, lamotrigine (LTG) in human plasma. The CZE-MS was developed in three stages: (i) CZE separation and ESI-MS detection of LTG and tyramine (TRM, internal standard) were simultaneously optimized by studying the influence of CZE background electrolyte (BGE) pH, BGE ionic strength, and nebulizer pressure of the MS sprayer; (ii) sheath liquid parameters, such as pH, ionic strength, organic modifier content, and flow rate of the sheath liquid, were systematically varied under optimum CZE-MS conditions developed in the first stage; (iii) MS sprayer chamber parameters (drying gas temperature and drying gas flow rate) were varied for the best MS detection of LTG. The developed assay was finally applied for the determination of LTG in plasma samples. The linear range of LTG in plasma sample assay was between 0.1-5.0 microg/mL with a limit of detection as low as 0.05 microg/mL and run time less than 6 min. Finally, the concentration-time profile of LTG in human plasma sample was found to correlate well when CZE-ESI-MS was compared to a more established method of high-performance liquid chromatography with ultraviolet detection.     

On-line coupling of capillary isotachophoresis and zone electrophoresis for the assay of phenolic compounds in plant extracts

The combination of capillary isotachophoresis (ITP) and capillary zone electrophoresis (CZE) in the column coupling configuration was optimized in a mode where the electrolyte for the CZE step is different from the leading and terminating ITP electrolytes. Two colored markers, picric acid and 1-nitroso-2-naphthol, were used for exact timing of the transfer of isotachophoretically stacked analyte zones into the CZE column and for the control of the residual amount of the leading and terminating ITP electrolytes entering the CZE capillary together with the analytes, thus controlling the duration of transient ITP migration in the CZE capillary and ensuring good separation of the analytes and reproducibility of the migration times (relative standard deviations 1%). ITP-CZE was applied to the simultaneous assay of several cinnamic acid derivatives and flavonoids in methanolic extracts of Sambucus flowers and Crataegus leaves and flowers. The preconcentrating and cleansing effect of the ITP step allowed injection of relatively large sample volumes (30 microL). The limits of detection were approximately 20-50 ng x mL(-1) and 100 ng x mL(-1) for the acids and flavonoids, respectively ( thick similar 200-times lower compared to conventional CE) with spectrophotometric detection at 254 nm. The ITP-CZE exhibited satisfactory linearity and precision when using CZE buffer of pseudo "pH" 9.0; 1-nitroso-2-naphthol was employed as the internal standard. The separation took approximately 35 min. The ITP-CZE results for rutin, hyperoside, and vitexin-2-O"-rhamnoside were in good accordance with those obtained previously by high-performance liquid chromatography.     

Liquid chromatographic and spectrophotometric determination of diflucortolone valerate and isoconazole nitrate in creams

A new RP-LC method and two new spectrophotometric methods, principal component regression (PCR) and first derivative spectrophotometry, are proposed for simultaneous determination of diflucortolone valerate (DIF) and isoconazole nitrate (ISO) in cream formulations. An isocratic system consisting of an ACE C18 column and a mobile phase composed of methanol-water (95 + 5, v/v) was used for the optimal chromatographic separation. In PCR, the concentration data matrix was prepared by using synthetic mixtures containing these drugs in methanol-water (3 + 1, v/v). The absorbance data matrix corresponding to the concentration data matrix was obtained by measuring the absorbances at 29 wavelengths in the range of 242-298 nm for DIF and ISO in the zero-order spectra of their combinations. In first derivative spectrophotometry, dA/dlambda values were measured at 247.8 nm for DIF and at 240.2 nm for ISO in first derivative spectra of the solution of DIF and ISO in methanol-water (3 + 1, v/v). The linear ranges were 4.00-48.0 microg/mL for DIF and 50.0-400 microg/mL for ISO in the LC method, and 2.40-40.0 microg/mL for DIF and 60.0-260 microg/mL for ISO in the PCR and first derivative spectrophotometric methods. These methods were validated by analyzing synthetic mixtures. These three methods were successfully applied to two pharmaceutical cream preparations.     

Analysis of acrylamide in food products by in-line preconcentration capillary zone electrophoresis

Two in-line preconcentration capillary zone electrophoresis (CZE) methods (field amplified sample injection (FASI) and stacking with sample matrix removal (LVSS)) have been evaluated for the analysis of acrylamide (AA) in foodstuffs. To allow the determination of AA by CZE, it was derivatized using 2-mercaptobenzoic acid. For FASI, the optimum conditions were water at pH > or = 10 adjusted with NH3 as sample solvent, 35 s hydrodynamic injection (0.5 psi) of a water plug, 35 s of electrokinetic injection (-10 kV) of the sample, and 6s hydrodynamic injection (0.5 psi) of another water plug to prevent AA removal by EOF. In stacking with sample matrix removal, the reversal time was found to be around 3.3 min. A 40 mM phosphate buffer (pH 8.5) was used as carrier electrolyte for CZE separation in both cases. For both FASI and LVSS methods, linear calibration curves over the range studied (10-1000 microg L(-1) and 25-1000 microg L(-1), respectively), limit of detection (LOD) on standards (1 microg L(-1) for FASI and 7 microg L(-1) for LVSS), limit of detection on samples (3 ng g(-1) for FASI and 20 ng g(-1) for LVSS) and both run-to-run (up to 14% for concentration and 0.8% for time values) and day-to-day precisions (up to 16% and 5% for concentration and time values, respectively) were established. Due to the lower detection limits obtained with the FASI-CZE this method was applied to the analysis of AA in different foodstuffs such as biscuits, cereals, crisp bread, snacks and coffee, and the results were compared with those obtained by LC-MS/MS.     

Analysis of acrylamide in food samples by capillary zone electrophoresis

Conditions for the determination of acrylamide (AA) after derivatisation with 2-mercaptobenzoic acid by capillary zone electrophoresis were established. A derivatisation reagent-acrylamide ratio of 35:1 was selected as optimum and the reagent excess was not removed as it did not affect the determination of acrylamide by CZE. The best separation was achieved using a 40 mM phosphate buffer at pH 8.0, working at 25 kV in un-coated fused silica capillaries. Linear calibration curves over the range studied (0.3-100 microg mL(-1)), the limit of detection (0.07 microg mL(-1)), and both run-to-run (RSD values of 5.8 and 2.2% for concentration at low and medium concentration levels, respectively) and day-to-day precisions (up to 11.2 and 6.7% at low and medium concentration levels, respectively) were established. Finally, the applicability of the CZE proposed methodology was demonstrated by analyzing levels of acrylamide present in different foodstuff products such as home made french fries, breakfast cereals and biscuits.     

Determination of nitrite and nitrate in a proposed certified reference material for nutrients in seawater by capillary zone electrophoresis with artificial seawater as the background electrolyte using transient isotachophoresis

We describe a combination of selected ions as a terminating ion which is useful for transient isotachophoresis (ITP) in capillary zone electrophoresis (CZE) for the determination of nitrite and nitrate in seawater. In addition to 150 mM sulfate as the principal terminating ion, 10 mM bromate was added to a sample solution as the additional terminating ion. Artificial seawater containing 3 mM cetyltrimethylammonium chloride (CTAC) was adopted as a background electrolyte (BGE). The limits of detection (LODs) for nitrite and nitrate were 2.2 and 1.0 microg/L (as nitrogen), respectively. The LODs were obtained at a signal to noise ratio (S/N) of 3. The values of the relative standard deviation (RSD) of peak area for these ions were 1.9 and 1.4%. The RSDs of peak height were 1.7 and 1.9%, the RSDs of migration time 0.11%. The proposed method was applied to the determination of nitrite and nitrate in a proposed certified reference material for nutrients in seawater, MOOS-1, distributed by the National Research Council of Canada (NRC). The results almost agreed with the assigned tolerance interval.     

Comparative study of the determination of peroxomonosulfate, in the presence of other oxidants, by capillary zone electrophoresis, ion chromatography, and photometry

Several methods for quantitative determination of peroxomonosulfate in detergents, in the presence of other oxidants, have been investigated. The photometric technique applied was based on the well-known starch-iodine reaction. The oxidizing agent was quantified by determining the amount of iodine produced. The influence of other oxidants present was examined. Ion analysis was performed by capillary zone electrophoresis (CZE) and ion chromatography (IC). Because peroxomonosulfate in detergents is always accompanied by sulfate, the main goal was to separate the sulfur species without causing the decomposition of the unstable peroxomonosulfate ion. The sulfur species could be separated within less than 4 min by CZE with a pyromellitic acid electrolyte at pH 3.5 to 5.0. Sulfate and peroxomonosulfate were separated by IC within 11 min by use of a phthalic acid mobile phase at pH 3.0. The peroxomonosulfate content was determined by calibration. The calibration plot was linear from 5 to 50 microg mL(-1) SO5(2-) for IC and from 7.3 to 182.3 microg mL(-1) SO5(2-) (corresponding to 20 to 500 microg mL(-1) triple salt) for CZE.     

Quality control of benserazide-levodopa and carbidopa-levodopa tablets by capillary zone electrophoresis

In modern practice, the treatment of Parkinson's disease and syndrome is carried out using pharmaceutical formulations containing a combination of levodopa and a decarboxylation inhibitor (carbidopa or benserazide). Two pharmaceutical formulations were quantified by capillary zone electrophoresis using two procedures which differed only in the kind of background electrolyte used. One procedure used a 25 mM phosphate buffer, pH 2.5, while the second one used a 25 mM borate buffer, pH 8.5. The electrophoretic analysis was carried out using an uncoated fused- silica capillary, a separation voltage of 20 kV with currents typically less than 60 microA, and spectrophotometric detection at 205 nm. Calibration curves were performed for levodopa (concentration range 1-100 microg/mL), for carbidopa and benserazide (1-50 microg/mL), and the plots of the peak area versus concentration were found to be linear with a correlation coefficient better than 0.9990. Satisfactory results were obtained when commercial tablets were analyzed in terms of accuracy (98-102%), repeatability (0.6-2.0%), and intermediate precision (1.1-2.6%).     

Determination of preservatives by integrative coupling method of headspace liquid-phase microextraction and capillary zone electrophoresis

An integrative coupling method of headspace liquid-phase microextraction (HS-LPME) and capillary zone electrophoresis (CZE) was proposed in this paper. In the method, a separation capillary was used to create a microextraction droplet of the running buffer solution of CZE, hold the droplet at the capillary inlet, extract analytes of sample solutions in the headspace of a sample vial, inject concentrated analytes into the capillary and separate the analytes by CZE. The proposed method was applied to determine the preservatives of benzoic acid and sorbic acid in soy sauce and soft drink samples, in which the running buffer solution of 50 mmol/L tetraborate (pH 9.2) was directly used to form the acceptor droplet at the capillary inlet by pressure, and the preservatives in a 6-mL sample solution containing 0.25 g/mL NaCl were extracted at 90°C for 30 min in the headspace of a 14-mL sample vial. Then the concentrated preservatives were injected into the capillary at 10 cm height difference for 20 s and separated by CZE. The enrichment factors of benzoic acid and sorbic acid achieved 266 and 404, and the limits of detection (LODs) were 0.03 and 0.01 μg/mL (S/N=3), respectively. The recoveries were in the range of 88.7-105%. The integrative coupling method of HS-LPME and CZE was simple, convenient, reliable and suitable for concentrating volatile and semi-volatile organic acids and eliminating matrix interferences of real samples.     

Rapid quantitative analysis of phenazine-1-carboxylic acid and 2-hydroxyphenazine from fermentation culture of Pseudomonas chlororaphis GP72 by capillary zone electrophoresis

Natural phenazines in secondary metabolites of bacteria have been receiving increasing attention in recent years due to their potential usage as antibiotics. In the present study, a rapid and reliable capillary zone electrophoresis (CZE) method was developed and validated for monitoring for the first time dynamic phenazine-1-carboxylic acid (PCA) and the 2-hydroxyphenazine (2-OH-PHZ) production of Pseudomonas chlororaphis GP72 during the entire fermentation cycle. The paper begins with the optimization of separate conditions for 2-OH-PHZ and PCA together with phenazine (PHZ), which is used as internal standard. The optimized conditions are: 10mM, pH 7.3 phosphate buffer, a fused-silica capillary with a total length of 49 cm x 75 microm ID, 375 microm OD with an effective length of 40 cm, 25 kV, 13 mbar 10s pressure sample injection and 25 degrees C air-cooling. The three compounds could be separated within 2 min under optimized conditions. The validation of the newly developed study shows the linear response of 2-OH-PHZ and PCA ranging from 10 to 250 microg mL(-1) with high correlation coefficient (r=0.9997 and 0.9993, n=7), low limits of detection (0.47 and 0.38 microg mL(-1)) and quantification (1.56 and 1.28 microg mL(-1)), respectively. Good precision values for intra- and inter-day detection and acceptable individual recovery ranges for 2-OH-PHZ and PCA are indicated. The newly developed method was also validated through monitoring dynamic PCA and 2-OH-PHZ production of P. chlororaphis GP72 during an 84 h growth cycle.     

Enhanced separation of purine and pyrimidine bases using carboxylic multiwalled carbon nanotubes as additive in capillary zone electrophoresis

This paper describes the enhanced separation of adenine (A), hypoxanthine (HX), 8-azaadenine (8-AA), thymine (T), cytosine (C), uracil (U) and guanine (G) by CZE dispersing carboxylic multiwalled carbon nanotubes (c-MWNTs) into the running buffer. The effect of important factors such as c-MWNT nanoparticle concentration, the acidity and concentration of running buffer, and separation voltage were investigated to acquire the optimum conditions. The seven purine and pyrimidine bases could be well separated within 16 min in a 35 cm effective length fused-silica capillary at a separation voltage of +8.0 kV in a 23 mM tetraborate buffer (pH 9.2) containing 8.0 x 10(-5) g/mL c-MWNTs. Under the optimal conditions, the linear ranges were of 2-250 microg/mL for A (R2 = 0.995), 3-200 microg/mL for U (R2 = 0.990) and G (R2 = 0.992), 3-250 microg/mL for T (R2 = 0.998), 2-200 microg/mL for C (R2 = 0.985) and 4-200 microg/mL for HX (R2 = 0.988) and 8-AA (R2 = 0.990). The detection limits were 0.9 microg/mL for A (S/N = 3), 2.4 microg/mL for U, 2.0 microg/mL for T, 1.5 microg/mL for C, 2.5 microg/mL for G and 3.0 microg/mL for HX and 8-AA. The proposed method was successfully applied for determining five purine and pyrimidine bases in yeast RNA.     

Quantification of L-ascorbic acid and total ascorbic acid in fruits and spinach by capillary zone electrophoresis

A standard curve for the quantification of L-ascorbic acid (L-AA) by capillary zone electrophoresis (CZE) was established, and the quantification of ascorbic acid and total ascorbic acid in fruits (lemon, Sunkist, and pineapple) and spinach were performed using D-isoascorbic acid (D-IAA) as an internal standard. The minimum detection limits (MDLs) for L-AA and D-IAA were determined to be 1 and 2 microg/mL, respectively, at 265 nm. Dehydroascorbic acid (DHAA) in fruits and spinach was quantified in the presence of DL-homocysteine. The recoveries for L-AA in these juices were between 95 and 105%.