流动注射-氢化物发生-原子荧光光谱法测定茶叶中硒

取经烘干且粉碎的茶叶样品0.5g,用硝酸-高氯酸(4+1)混合酸10mL置于电热板上加热消解至溶液呈透明,继续蒸发至剩余约2mL溶液,加入6mol.L-1盐酸溶液5mL,加热使硒(Ⅵ)还原至硒(Ⅳ),重复3次,每次加水2mL,蒸发以驱除溶液中酸,最后用盐酸(4+96)溶液定容为25mL。将此溶液以盐酸(4+96)溶液作载流引入流动注射分析系统,同时引入10g.L-1硼氢化钾溶液(溶于5g.L-1氢氧化钾溶液中)作还原剂。硒的质量浓度在80μg.L-1以内与其荧光强度值呈线性关系。方法的检出限(3s/k)为0.034μg.L-1。应用此方法分析了3种茶叶样品,并以此为基体,加入硒标准溶液做回收试验,测得回收率在97.8%～103.0%之间,测定值的相对标准偏差(n=6)均小于1.5%。     

微波消解-氢化物发生-原子荧光光谱法同时测定土壤及生物样品中铅和汞

应用氢化物发生-原子荧光光谱法测定了土壤及生物样品中铅和汞。样品用硝酸4mL及过氧化氢1mL按微波消解仪的工作参数进行消解,消解后溶液定容至25mL供测定。用30g·L-1柠檬酸溶液和硝酸(1+99)溶液的混合液作载流,根据铅(Ⅱ)离子的反应和试液对酸度的要求,选用含15g·L-1硼氢化钾,10g·L-1铁氰化钾和20g·L-1氢氧化钾的混合溶液作为还原剂。方法的检出限(3s/k)为0.512μg·L-1(铅)和0.067μg·L-1(汞)。应用此方法分析了3种实样并进行加标回收试验,测得回收率分别在91.0%~97.0%(铅)和88.0%~95.5%(汞)之间。     

氢化物发生-原子荧光光谱法测定海产品中总砷

采用氢化物发生-原子荧光光谱法测定海产品中总砷的含量。样品经硝酸-高氯酸(4+1)混合酸消解,样品溶液中加入硫脲和抗坏血酸混合溶液作为预还原剂。于盐酸(5+95)溶液中加入10g.L-1硼氢化钾-5g.L-1氢氧化钾溶液使与溶液中砷离子反应生成氢化物。分析时采用载气流量为400mL.min-1,屏蔽气流量为800mL.min-1。砷的质量浓度在20μg.L-1以内与荧光强度呈线性关系,方法的检出限(3s/k)为0.015μg.L-1。应用此法对3种海产品进行分析,测定值的相对标准偏差(n=6)在3.4%～4.2%之间,回收率在98.5%～101.0%之间。     

加速溶剂提取-液相色谱-原子荧光光谱法测定对虾饲料中5种形态的汞

称取经粉碎的样品1.000 0g,置于加速溶剂提取池中,加入10mL的5mol·L-1盐酸溶液、1mL的5mol·L-1氯化钾溶液和2mL的10mol·L-1半胱氨酸溶液;在8.0MPa和70℃下,预加热2min,加热5 min,静态提取5min,分离,重复上述提取过程2次,合并提取液;加入0.2mL的0.5mol·L-1半胱氨酸溶液、1.5mL的6mol·L-1氢氧化钠溶液,以10 000r·min-1离心5min,将上清液氮吹浓缩并用硝酸(5+95)溶液定容至1mL,过0.45μm尼龙滤膜后,采用Eclipse XDB-C18反相色谱柱(150mm×4.6mm,5.0μm)分离溶液中的甲基汞、乙基汞、无机汞、硫柳汞和苯基汞,流动相为50g·L-1乙腈溶液+5g·L-1乙酸铵溶液+1g·L-1半胱氨酸溶液(体积比为1∶1∶1),用原子荧光光谱仪进行测定。5种形态的汞的质量浓度在一定范围内与其荧光强度呈线性关系,测定下限(10S/N)在1.0~2.5μg·kg-1之间。加标回收率在91.0%~98.3%之间,测定值的相对标准偏差(n=6)在0.94%~2.7%之间。     

加速溶剂提取-液相色谱-原子荧光光谱法测定对虾饲料中5种形态的汞北大核心CSCD

称取经粉碎的样品1.000 0g,置于加速溶剂提取池中,加入10mL的5mol·L-1盐酸溶液、1mL的5mol·L-1氯化钾溶液和2mL的10mol·L-1半胱氨酸溶液;在8.0MPa和70℃下,预加热2min,加热5 min,静态提取5min,分离,重复上述提取过程2次,合并提取液;加入0.2mL的0.5mol·L-1半胱氨酸溶液、1.5mL的6mol·L-1氢氧化钠溶液,以10 000r·min-1离心5min,将上清液氮吹浓缩并用硝酸(5+95)溶液定容至1mL,过0.45μm尼龙滤膜后,采用Eclipse XDB-C18反相色谱柱(150mm×4.6mm,5.0μm)分离溶液中的甲基汞、乙基汞、无机汞、硫柳汞和苯基汞,流动相为50g·L-1乙腈溶液+5g·L-1乙酸铵溶液+1g·L-1半胱氨酸溶液(体积比为1∶1∶1),用原子荧光光谱仪进行测定。5种形态的汞的质量浓度在一定范围内与其荧光强度呈线性关系,测定下限(10S/N)在1.0~2.5μg·kg-1之间。加标回收率在91.0%~98.3%之间,测定值的相对标准偏差(n=6)在0.94%~2.7%之间。     

氢化物发生-双通道原子荧光光谱法同时测定茶叶和木耳中硒及汞量

经洗净烘干并磨碎的试样在硝酸中浸泡过夜后在硝酸-高氯酸中消解,蒸发至冒白烟并继续蒸至近干,加入一定量的盐酸微沸1～2min,使硒(Ⅵ)还原为硒(Ⅳ),溶液用盐酸(5+95)定容至50mL。此溶液由载流盐酸(5+95)溶液送入氢化物发生器,与还原剂10g.L-1 KBH4溶液混合并反应生成硒的氢化物,样品中汞则生成原子态汞蒸气。两者由载气引入原子化器,在选定的仪器工作条件下,测定硒及汞的荧光强度。在实际样品中,硒、汞共存的浓度比未超过10,在同时测定中两者之间互不干扰。按所提出的条件测定,硒、汞的质量浓度在1.0～5.0μg.L-1范围内与相应的荧光强度值之间呈线性关系,方法的检出限(3s/k)依次为0.077,0.009 8μg.L-1。对仪器测定精密度做了试验,测得其相对标准偏差(n=7)依次为1.98%,1.31%。     

氢化物发生-原子荧光光谱法测定茶水中砷

采用氢化物发生-原子荧光光谱法测定茶水中砷含量。样品经硝酸-高氯酸(4+1)混合酸消解,在盐酸(6+94)溶液中加入30 g·L-1硼氢化钾-5 g·L-1氢氧化钾溶液使与溶液中砷离子反应生成氢化物。分析中采用载气流量为400 mL·min-1。试样溶液中加入硫脲及抗坏血酸混合溶液作为预还原剂。引入仪器的进取样量为1.2 mL,按选定的工作条件操作。荧光强度与砷的质量浓度在0.20~100μg·L-1范围内呈线性关系,方法的检出限(3s/k)为0.030μg·L-1。应用此法对3种茶叶泡出的茶水进行分析,测得回收率在97.7%~101.5%之间。     

氢化物发生-原子荧光光谱法测定铝合金中痕量锑

铝合金样品用盐酸及硝酸的混合酸溶解,于分取的部分试样溶液中加入碘化钾-硫脲混合溶液后用盐酸(5+95)定容为50 mL,供氢化物发生-原子荧光光谱法测定其中痕量锑。用40 g.L-1碘化钾溶液作为锑(Ⅴ)的预还原剂,40 g.L-1硫脲溶液作为其他可形成氢化物的元素的掩蔽剂,选用20 g.L-1硼氢化钾溶液作为产生锑化氢的还原剂,氢化物发生反应在盐酸(5+95)介质中进行,锑的质量浓度在0.05~50.0μg.L-1范围内与相应的荧光强度呈线性关系。方法的检出限(3s/k)为0.016μg.L-1。应用此方法分析了两件铝合金标准样品,测得锑量的结果与认定值相符,测定值的相对标准偏差(n=8)分别为2.14%和3.16%。     

氢化物发生-原子荧光光谱法测定岩石中砷和锑

应用氢化物发生-原子荧光光谱法测定了岩石中砷和锑的含量。样品预先粉碎至通过孔径为0.25～0.42mm的细筛,称取此粉碎的样品0.1000～0.3000g,先于盐酸-硝酸(3+1)混合酸8mL中浸泡30 min,然后放入沸水浴中消解2 h,将溶液及不溶物一起移入50 mL容量瓶中,加水定容。移取上清液5.00mL置于10mL容量瓶中,加入100g·L~(-1)硫脲及抗坏血酸混合溶液2.5mL,用盐酸(5+95)溶液定容,分取此溶液1.0mL进样按选定的仪器条件进行分析。用20g·L~(-1)硼氢化钾溶液作为产生砷及锑的氢化物的还原剂,砷(Ⅲ)及锑(Ⅲ)的质量浓度依次在0.50～60μg·L~(-1)和0.50～80μg·L~(-1)范围内与其相应的荧光强度呈线性关系。应用此方法测定了两种岩石标准物质(GBW 07106及GBW 07108)中的砷及锑量,其测定值与认定值一致,相对标准偏差(n=5)均小于3.5%。     

电感耦合等离子体原子发射光谱法测定铜电积液中锑、铋、钴、镍和砷的含量

样品(2.00mL)用盐酸10mL、硝酸3mL溶解后,蒸馏至2~3mL,加入100g·L-1酒石酸溶液2mL,用盐酸(5+95)溶液稀释定容至100mL。采用电感耦合等离子体原子发射光谱法测定样品溶液中锑、铋、钴、镍和砷的含量。选择锑、铋、钴、镍、砷元素的分析谱线分别为206.836,223.061,228.615,231.604,193.696nm。5种元素在一定的质量浓度范围内与其发射强度呈线性关系,方法的检出限(3s)在0.005~0.130mg·L-1之间。方法用于铜电积液分析,所得测定值与火焰原子吸收光谱法测定结果相符。加标回收率在95.8%~108%之间,测定值的相对标准偏差(n=11)在0.70%~6.4%之间。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.