PVA增强P(AAEA-co-AA)温度敏感性水凝胶的合成及其性能研究

以4-乙酰基丙烯酰乙酸乙酯(AAEA)、丙烯酸(AA)以及PVA为原料, 通过自由基溶液聚合法, 制备了PVA-P(AAEA-co-AA)半穿网络型(s-IPN)水凝胶. 红外分析表明, AAEA主要以烯醇式结构存在, 并且由于PAAEA, PAA以及PVA之间较强的氢键作用, 使得PAAEA以及PVA分子上的C-O伸缩振动吸收峰移向了低波数处. 电镜分析表明, PVA能贯穿于P(AAEA-co-AA)交联网络中, 从而有效阻碍凝胶的相分离|而XRD研究发现, 当PVA用量较少时, PVA能均匀的贯穿于凝胶网络中, 形成完善的互穿网络结构, 当PVA用量过高时, PVA不能有效地贯穿于聚合物交联网络中而出现结晶. 采用DSC对s-IPN水凝胶的体积相转变进行了研究, 结果表明, 该s-IPN水凝胶的体积相转变温度(VPTT)在54.0至57.8 ℃之间, 并且随着PVA用量的增加, 凝胶的VPTT逐渐升高. 研究了该s-IPN水凝胶的抗压缩性能, 结果表明, PVA与P(AAEA-co-AA)形成的半互穿网络结构能有效提高凝胶的抗压缩强度, 其最大抗压缩强度可达8.4 MPa. 对凝胶的温度敏感性研究发现, 当外界温度低于VPTT时, 凝胶能保持溶胀状态|而当温度高于VPTT时, 凝胶的平衡溶胀度迅速下降, 表现为温度敏感性.     

PVP-P(AAEA-co-AA)/纳米金温度-电场双重敏感性凝胶的制备及性能

采用溶液聚合法以聚乙烯吡咯烷酮(PVP)为第二网络,以丙烯酸(AA)、4-乙酰基丙烯酰乙酸乙酯(AAEA)为单体制备PVP-P(AAEA-co-AA)半互穿水凝胶(PVP-SIPN),再通过原位还原法合成PVP-P(AAEA-co-AA)/纳米金复合凝胶(GNPs gel),探讨凝胶的溶胀/消溶胀性能、温度及电场敏感性。研究表明,随PVP用量的增加PVP-SIPN溶胀速率减小,平衡溶胀度降低;当PVP用量低于5%凝胶保水率随PVP用量增加而降低,高于5%时保水率随PVP用量增加而增加;PVP-SIPN相转变温度升高,且凝胶温度敏感性随之减弱。纳米金的加入导致凝胶平衡溶胀度从82.3g/g降低至22.66g/g,在电场作用下,外界离子浓度小于0.2mol/L时,GNPs gel发生溶胀;反之,消溶胀,凝胶消溶胀速率随外界电压增大而增大。     

一种快速响应电场敏感多孔水凝胶的合成及其性能研究

以4-乙酰基丙烯酰乙酸乙酯(AAEA)、2-丙烯酰胺基-2-甲基-1-丙磺酸(AMPS)为单体,不同分子量的聚乙二醇(PEG)为成孔剂,通过自由基溶液聚合法,合成了新型多孔快速响应电场敏感性水凝胶.结果表明,成孔剂PEG被洗脱后在凝胶内部形成了互相贯穿的孔洞结构,孔径在30～120μm之间.以PEG6000为成孔剂致孔后的多孔凝胶溶胀速率和消溶胀速率最快,在去离子水中30s达到溶胀平衡,在0.1mol/L的NaCl溶液中40min达到消溶胀平衡;电场作用下凝胶的消溶胀速度大大加快,12min内即可达到平衡.凝胶中AMPS含量的增多会加快凝胶在电场中的响应速度;而高温下,随着AAEA含量的增加,凝胶内部疏水基团增多并收缩产生大量的疏水微区,限制了凝胶内部水分的持续排出,因此n(AAEA)∶n(AMPS)=3∶1的凝胶4min内即可排出表面水分达到消溶胀平衡,可保水率却高达75%.同时,增大电解液的pH值、浓度以及提高电解电压,均会加快凝胶的消溶胀行为.     

含金刚烷基的N-异丙基丙烯酰胺共聚物水凝胶的制备和性能研究

合成了含金刚烷基的甲基丙烯酸金刚烷酯(AdMA)疏水单体,并通过与N-异丙基丙烯酰胺(NIPAM)共聚,制备了温敏性的(P(NIPAM-co-AdMA))共聚物水凝胶.用傅里叶变换红外光谱仪(FTIR)表征了凝胶的化学结构,用环境扫描电镜(ESEM)对凝胶断层结构的形貌进行了观察,用DSC测试了凝胶的体积相转变温度(LCST),并研究了共聚水凝胶的溶胀性能.结果表明,共聚物水凝胶的LCST能够高效地通过改变疏水单体的含量来调节,在实验所考察的范围内,LCST随AdMA含量的增加而线性降低;疏水单体的含量对凝胶的孔洞结构和溶胀性能存在一最优值,在最优的单体配比下,水凝胶具有均匀规整的大孔结构和超快的响应速率.如疏水单体含量为3%(AdMA∶NIPAM=3%)的共聚物水凝胶具有如渔网般均匀的多孔结构,当发生去溶胀时,在5min内就可以失去92%的水,不到10min的时间就可以完全达到去溶胀平衡,水保留率在4%以下.     

温度/pH敏感性接枝共聚物水凝胶P(DMAEMA-g-NIPAM)的 合成及性质研究

利用大分子单体技术, 采用自由基溶液聚合合成了温度/pH敏感性聚甲基丙烯酸-N,N-二甲氨基乙酯接枝聚N-异丙基丙烯酰胺[P(DMAEMA-g-NIPAM)]水凝胶. 用红外光谱及扫描电镜对凝胶的组成及形貌进行了表征. 凝胶的去溶胀和溶胀动力学研究表明, 所合成的凝胶具有温度和pH敏感性. 与传统的聚丙烯酸系水凝胶相比, P(DMAEMA-g- NIPAM)具有相反的pH敏感性; P(DMAEMA-g-NIPAM)凝胶在55 ℃时具有较快的去溶胀速率, 随着凝胶中接枝链PNIPAM量的增加, 凝胶的去溶胀速率加快.     

泡沫分散聚合法制备超大孔水凝胶及其性能研究

采用泡沫分散聚合法,以自制的4-乙酰基丙烯酰乙酸乙酯(AAEA)和2-丙烯酰胺基-2-甲基丙磺酸(AMPS)、丙烯酸(AA)为单体,制备了具有相互贯穿超大孔结构的快速响应型水凝胶.结果表明,引发剂和交联剂用量分别为2.5%和0.6%时平衡溶胀度最高;当以饱和碳酸钠溶液为发泡剂时制得的凝胶孔洞均匀贯穿;凝胶经无水乙醇处理...     

P(AMPS-co-BMA)水凝胶的电场敏感性及电刺激响应机理

以离子型单体2-丙烯酰胺-2-甲基丙磺酸(AMPS)及非离子型单体甲基丙烯酸丁酯为原料, 偶氮二异丁腈为引发剂, N,N′-亚甲基双丙烯酰胺为交联剂, N,N-二甲基甲酰胺为溶剂, 通过自由基聚合合成了一系列聚离子浓度不同的聚(2-丙烯酰胺-2-甲基丙磺酸-co-甲基丙烯酸丁酯)电场敏感性水凝胶. 研究了其在去离子水及NaCl溶液中的溶胀行为. 结果表明, 该水凝胶在去离子水中的平衡溶胀度在236.4~298.5之间, 其溶胀速率随着AMPS用量的增加而增加; 并且随着凝胶内部聚离子浓度的增加, 凝胶在NaCl溶液中的消溶胀速率及消溶胀度逐渐减小. 凝胶的电刺激响应性能研究结果表明, 在电场存在下, 凝胶在NaCl溶液中的溶胀行为与凝胶内部聚离子浓度和溶液中NaCl浓度的相对大小有关, 当凝胶内部聚离子浓度大于溶液中NaCl浓度时, 凝胶溶胀, 反之则凝胶消溶胀; 而且, 凝胶在电场作用下的偏转行为同样与凝胶内部聚离子浓度和溶液中NaCl浓度的相对大小有关, 当凝胶内部聚离子浓度大于溶液中NaCl浓度时, 偏向阴极, 反之则凝胶偏向阳极. 另外, 在电场存在下, 凝胶在NaCl溶液中的电偏转速度与环境温度密切相关.     

温度和pH敏感P(NIPA-co-AA)/粘土复合水凝胶的辐射制备与表征

以N-异丙基丙烯酰胺(NIPA)作为温敏性聚合单体,丙烯酸(AA)为pH敏感性单体,有机粘土为改性剂,采用~(60)Co-γ射线为辐射源,辐射合成了P(NIPA-co-AA),粘土复合水凝胶,研究了粘土的加入对水凝胶溶胀率、温度及pH敏感性和压缩性能的影响.结果表明,P(NIPA-co-AA)/粘土复合水凝胶的溶胀性能优于P(NIPA-co-AA)水凝胶,平衡溶胀率(SR)明显提高;且复合水凝胶仍表现出明显的温度和pH敏感性;粘土的加入提高了水凝胶的压缩强度、最大压缩力和压缩屈服力等力学性能,当粘土含量为15%时,P(NIPA-co-AA)/粘土复合水凝胶的压缩强度为P(NIPA-co-AA)共聚水凝胶的2.4倍,最大压缩力为P(NIPA-co-AA)的2.1倍.     

P(AA-DAC)两性聚电解质水凝胶的合成及性质

以丙烯酸(AA)和丙烯酰氧乙基三甲基氯化铵(DAC)为单体, 采用水溶液聚合法制备了P(AA-DAC)聚电解质水凝胶. 采用红外光谱和核磁共振等方法对其结构进行了表征. 研究了不同组成比的聚电解质水凝胶在去离子水、不同pH值溶液以及不同离子强度盐溶液中的溶胀行为. 研究结果表明, 摩尔比为1∶1的聚电解质水凝胶表现出典型的两性聚电解质凝胶的溶胀行为. 离子强度对其溶胀行为有着显著影响, 在溶液离子强度较高时, 凝胶网络的溶胀主要受溶剂向凝胶内部扩散所控制, 满足Fick型扩散规律n≤0.5, 随着溶液离子强度的增加, 凝胶网络平衡含水量增加, 扩散系数增大.     

PVA-PAMPS-PAA三元互穿网络型水凝胶的合成及其性能研究

以2-丙烯酰胺基-2-甲基丙磺酸(AMPS)、丙烯酸(AA)以及聚乙烯醇(PVA)为原料,制备了PVA-PAMPS-PAA三元互穿网络型(T-IPN)水凝胶.红外分析表明,PVA与PAA以及PAMPS之间形成了较强的氢键,使得PVA分子上的C—O伸缩震动吸收峰移向了低波数处.X射线衍射以及电镜分析表明,当PVA用量较低时,PVA能均匀的穿插于凝胶网络中,形成完善的互穿网络结构,当PVA用量过高时,部分的PVA结晶而使得凝胶出现相分离.研究了该三元互穿网络型水凝胶的溶胀性能,结果表明,该水凝胶的平衡溶胀比在200至340之间,并且随着AA以及AMPS用量的增加,凝胶的溶胀速率以及平衡溶胀比均升高.该三元互穿网络型水凝胶在酸性溶液中和在碱性溶液中表现出截然不同的消溶胀性能;并且随着溶液pH的升高,凝胶在pH=9.0附近出现体积突变,表现出pH敏感性.通过研究T-IPN水凝胶的抗压缩性能发现,利用线型高分子、柔性高分子网络以及刚性高分子网络制备的三元互穿网络型水凝胶能在高溶胀比下保持较高的强度.溶胀比为180的T-IPN水凝胶,其最大抗压缩强度可达12.1 MPa.进一步研究发现,凝胶的组成以及溶胀比均对凝胶的抗压缩强度和压缩应变均存在较大的影响.     

大孔PAMPS/PVA半互穿网络型水凝胶的制备及其性能研究

以PEG6000为成孔剂, 合成了大孔聚(2-丙烯酰胺-2-甲基丙磺酸)/聚乙烯醇半互穿网络型(s-IPN)水凝胶. 红外分析表明, PVA与PAMPS之间形成了较强的氢键, 使得PVA分子上的C—O伸缩振动吸收峰移向了低波数处. X射线衍射分析发现, 当PVA用量较高时, 由于部分的PVA结晶, 使得凝胶的半互穿网络结构不均匀. 电镜分析结果表明, 没有使用成孔剂的凝胶表面成褶皱形, 不存在任何孔洞结构; 而以PEG6000为成孔剂的凝胶表面存在相互贯穿的大孔结构. 研究了该水凝胶的溶胀性能, 结果表明, 该水凝胶的平衡溶胀度在116至320之间; 而成孔剂PEG6000的加入能较大幅度提高凝胶的溶胀速率, 凝胶在240 min之内就能达到溶胀平衡. 对凝胶抗压缩性能的研究表明, 当PVA用量为9.1% (w)时, 凝胶的抗压缩强度最大, 可达12.0 MPa; 而成孔剂的加入会在一定程度削弱凝胶的抗压缩强度. 该凝胶具有较好的电场敏感性, 研究发现, 将吸去离子水达到溶胀平衡的凝胶放入施加有电场的0.2 mol•L－1 NaCl溶液中时, 凝胶迅速偏向阳极. 而PVA和成孔剂PGE6000的用量均对凝胶的偏转速度以及最大偏转角存在较大的影响.     

A novel pH‐ and thermo‐sensitive PVP/CMC semi‐IPN hydrogel: Swelling,phase behavior,and drug release study

Poly(N‐vinyl‐pyrrolidone) (PVP) hydrogel has been considered as a very interesting and promising thermosensitive material. The most vital shortcoming of PVP hydrogel as thermosensitive material is that it does not exhibit thermosensitivity under usual conditions. In this work, semi‐interpenetrating polymer network (semi‐IPN) hydrogels based on PVP and carboxymethylcellulose (CMC) were prepared. The volume phase transition temperature (VPTT) of the hydrogels was determined by swelling behavior and differential scanning calorimetry (DSC). The results showed that the VPTT was significantly dependent on CMC content and the pH of the swelling medium. The amount of CMC in the semi‐IPN hydrogels was 0.050, 0.075, and 0.100 g, the VPTT in buffer solution of pH 1.2 was 29.9 °C, 27.5 °C and 24.5 °C, respectively. In addition, the VPTT occurred in buffer solution of pH 1.2, but did not appear in alkaline medium. Bovine serum albumin (BSA) as a model drug was loaded and the in vitro release studies were carried out in different buffer solutions and at different temperatures. The results of this study suggest that PVP/CMC semi‐IPN hydrogels could serve as potential candidates for protein drug delivery in the intestine. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1749–1756, 2010     

基于Pickering乳液的磁性高强水凝胶的制备及性能表征

合成了一种磁性Fe3O4纳米颗粒稳定的水包油(O/W)Pickering乳液并以其作为交联剂,在适宜条件下引发单体丙烯酰胺聚合来制备了一种新型的磁性高强复合水凝胶.采用X射线衍射(XRD)及场发射扫描电子显微镜(SEM)分别对磁性Fe3O4纳米颗粒和复合水凝胶的结构进行了表征,结果表明Pickering乳胶粒子较均匀地分布在复合凝胶网络中.溶胀性能测试及溶胀动力学分析表明复合水凝胶具有良好的溶胀性能,能够吸收自身干重100倍左右的水,其溶胀过程不遵循Fickian扩散模型;拉伸测试表明该水凝胶具有优异的力学性能,其拉伸强度能够达到150 kPa左右,断裂伸长率能够达到300%左右,并且当其承受的应力释放后能快速地恢复到初始形态.磁性能测试的结果显示该水凝胶具有良好的磁性.     

Swelling behaviors of thermoresponsive hydrogels cross-linked with acryloyloxyethylaminopolysuccinimide

Based on a biodegradable cross-linker, acryloyloxyethylaminopolysuccinimide (AEA-PSI), a series of looser cross-linked poly(N-isopropylacrylamide-co-acrylic acid) [P(NIPAAm-co-AAc)] hydrogels were prepared, and their water content, swelling/deswelling kinetics, and the morphology of the gels were investigated. The swelling behaviors of AEA-PSI-cross-linked P(NIPAAm/AAc) hydrogels were investigated in Dulbecco’s phosphate-buffered saline (pH = 7.4), in the distilled water, and in the simulated gastric fluids (pH = 1.2), respectively. The water contents of the hydrogels were controlled by the monomer molar ratio of NIPAAm/AAc, swelling media, and the temperature. In the swelling kinetics, all the dried hydrogels exhibited fast swelling behavior, and the swelling ratios were influenced significantly by the amounts of AEA-PSI and AAc content. The deswelling kinetics of the hydrogel were independent of the content of AAc and cross-linker. Lastly, the morphology of the hydrogels was estimated by the field scan electron microscopy.     

Synthesis and Characterization of Hydrogels Based on Gamma Radiation Copolymerization of N‐isopropylacrylamide and Ethylene Glycol Dimethacrylate Monomers

Hydrogels based essentially on N‐isopropylacrylamide (NIPAAm) and different ratios of ethylene glycol dimethacrylate (EGDMA) monomer were synthesized by gamma radiation copolymerization. The thermal decomposition behavior of NIPAAm/EGDMA hydrogels was determined by thermogravimetric analysis (TGA). The effect of temperature and pH on the swelling behavior was also studied. The results showed that the ratio of EGDMA in the comonomer feeding solution has a great effect on the yield product, gel fraction and water content in the final hydrogel. In this regard, it was observed that the increase of EGDMA ratio decreased these properties. The TGA study showed that all the compositions of NIPAAm/EGDMA hydrogels displayed higher thermal stability than the hydrogel based on pure PNIPAAm hydrogel. The swelling kinetics in water showed that pure PNIPAAm and NIPAAm/EGDMA hydrogels reached equilibrium after 6 h. However, NIPAAm/EGDMA hydrogels show swelling in water lower than pure PNIPAAm. The results showed that the swelling character of pure PNIPAAm and NIPAAm/EGDMA hydrogels was affected by the change in temperature within the temperature range 25–40°C, and showed a reversible change in swelling in the pH range 4–7 depending on composition.     

温敏性半乳糖基化壳聚糖水凝胶的制备及其对HL-7702细胞增殖行为影响的研究

以壳聚糖(CS)为原料,在1-乙基-3-(3-二甲胺丙基)碳-二亚胺盐酸盐(EDC.HCL)和N-羟基琥珀酰亚胺(NHS)的活化作用下,合成了半乳糖基化壳聚糖(GC)单体,并与N-异丙基丙烯酰胺(NIPAAm)反应,制备了温敏性半乳糖基化壳聚糖N-异丙基丙烯酰胺共聚水凝胶(Gal-CS-g-PNIPAAm).通过红外光谱(FTIR)、光电子能谱(XPS)和扫描电子显微镜(SEM)等测试方法对其成分和结构进行了表征,并对其溶胀率和表面亲疏水性进行了研究.在Gal-CS-g-PNIPAAm凝胶表面培养人正常肝细胞系(HL-7702),研究其生长、脱附及转载(再增殖)行为.结果表明Gal-CS-g-PNIPAAm水凝胶具有良好的温度响应性和生物相容性,与PNIPAAm水凝胶相比,Gal-CS-g-PNIPAAm凝胶表面更有利于HL-7702细胞增殖.将温度降低至临界温度(LCST,32.5℃)以下,细胞可以从凝胶表面自发脱附,与酶消化脱附相比,细胞损伤更少.Gal-CS-g-PNIPAAm凝胶表面脱附的细胞比PNIPAAm凝胶表面脱附的细胞活性更高,表明PNIPAAm水凝胶引入GC单体后,凝胶的生物相容性得到改善,且脱附后细胞的增殖活力明显增加.     

磁性半互穿网络智能水凝胶的合成及性质评价

以甲基丙烯酸(MAA)、N-异丙基丙烯酰胺(NIPAAm)、丙烯酰胺(AM)为原料,N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,利用IPN技术并结合磁性的γ-Fe2O3增强剂,在水溶液中制备了半互穿网络水凝胶(PMAA/PAM-NIPAAm/γ-Fe2O3),研究了水凝胶的溶胀性﹑热稳定性和电磁性。实验表明,水凝胶形成稳定的IPN互穿网络结构且该水凝胶具温度、pH双重敏感性和顺电磁性。所合成的水凝胶在低临界溶解温度31℃以下,具有明显正向温敏性,高于此温度,水凝胶的温度敏感性会逐渐减弱。产品成功克服了NIPAAm类水凝胶的温缩性。     

STUDY ON THE SWELLING BEHAVIOUR OF COPOLYMER HYDROGEL

The states of water in poly (N-vinylpyrrolidone-methylmethacrylate) and poly (N-vinylpyrroli-done-2-hydroxyethyl methacrylate) hydrogels have been studied by means of DSC. The effect ofpolmer structure on equilibrium swelling extent of water has been examined. It was found that thestate of water and the water content in different hydrogels were dependent on the kind of monomer used,the component of copolymer, the sequence distribution of the monomer unit and the degree of cross-linking (including chemical and physical) to a great extent. The equilibrium water content of thehydrogel may be regarded as the sum of the different state of swollen water contents of the hydrogel.Based on these, a semiempirical formula used to estimate the equilibrium water content of the copolymerhydrogels was presented.     

Swelling behavior of ionically cross-linked polyampholytic hydrogels in varied salt solutions

Ionically cross-linked polyampholytic hydrogels were synthesized by redox copolymerization of acrylamide and an ionic complex of (N,N-diethylamino)ethyl methacrylate and acrylic acid (designated as PADA hydrogel). The swelling behavior of the hydrogels in water indicated that a minimal equilibrium swelling ratio is found when the molar ratio of anionic/cationic monomers was 1.55. In NaCl solution, the hydrogels exhibited the typical swelling behavior of conventional polyampholytic gels. Their equilibrium swelling ratios increased with an increase in the NaCl concentration. In solutions of multivalent ions (CaCl₂ and trisodium citrate solutions), the equilibrium swelling ratios of the hydrogels increased first and were then followed by a decrease with an increase in salt concentration. Interestingly, an unexpected abrupt swelling phenomenon was observed when the fully swollen hydrogels in salt solution were transmitted to pure water. The unique swelling behavior of PADA hydrogels depends not only on the molar ratio of the anionic/cationic monomers but also on the valency of the ions.