Thermal analysis and water-cooling design of the CSNS MEBT 324 MHz buncher cavity

At least two bunchers are needed in the 3 MeV H- Medium Energy Beam Transport(MEBT)line located between RFQ and DTL for the CSNS(China Spallation Neutron Source).A nose-cone geometry has been adopted as the type of buncher cavity for its simplicity,higher impedance and lower risk of multipacting.By making use of the results got from the simulations on the buncher with two-dimension code SUPERFISH,the thermal and structural analyses have been carried out,the process and results to determine the resulting frequency shift due to thermal and structural distortion of the cavity are presented,the water-cooling channel position and the optimum cooling water temperature as well as the tuning method by adjusting the cooling water temperature when the cavity is out of resonance are also determined through the analyses.     

管道连接装配型ITER增强热负荷第一壁的初步设计

中方承制的ITER第一壁采用大量焊接连接结构,冷却通道焊缝多,冷却水泄漏风险大,且存在焊接装配难以更换缺损部件等关键问题。在全尺寸原型件工艺认证阶段,需基于半原型研发基础,对其进行更改设计。设计重点在于手指部件采用前部燕尾槽和中部螺钉连接的固定结构,手指对采用前部管管连接、中部管连接件与中心梁焊接形成内部冷却通道回路。对初步设计模型进行了结构热及弹塑性分析。分析结果显示其温度、位移、强度均在可接受范围内,可以采用这种结构继续进行整个增强热负荷第一壁的详细设计。     

142.8MHz次谐波聚束腔的结构优化设计

 使用二维有限差分法分析软件Superfish和三维有限积分法分析软件MAFIA，对142.8MHz次谐波聚束腔的结构进行了模拟和优化研究，给出了聚束腔结构优化设计的步骤和方法，确定了优化后聚束腔的基本结构。分析比较了Superfish和MAFIA两个软件的模拟优化结果，得出了基本一致的结论。还探讨了Superfish和MAFIA在聚束腔设计中的应用方法。     

HIRFL新B1聚束器耦合环的设计与计算

 通过将聚束器腔体等效为RLC并联回路,求得了功率馈入耦合环与腔体的互感及自感的公式,根据对腔体的计算结果求出了在聚束器的工作频段内达到阻抗匹配所要求的互感变化范围,并在该互感变化范围设计了可移动的耦合电感环,计算了它的自感及整个腔体的剩余电感。     

Multi-physics analysis of the RFQ for Injector Scheme Ⅱ of C-ADS driver linac

A 162.5 MHz, 2.1 MeV radio frequency quadruples (RFQ) structure is being designed for the Injector Scheme Ⅱ of the China Accelerator Driven Sub-critical System (C-ADS) linac. The RFQ will operate in continuous wave (CW) mode as required. For the CW normal conducting machine, the heat management will be one of the most important issues, since the temperature fluctuation may cause cavity deformation and lead to the resonant frequency shift. Therefore a detailed multi-physics analysis is necessary to ensure that the cavity can stably work at the required power level. The multi-physics analysis process includes RF electromagnetic analysis, thermal analysis, mechanical analysis, and this process will be iterated for several cycles until a satisfactory solution can be found. As one of the widely accepted measures, the cooling water system is used for frequency fine tunning, so the tunning capability of the cooling water system is also studied under different conditions. The results indicate that with the cooling water system, both the temperature rise and the frequency shift can be controlled at an acceptable level.     

RF behavior and cavity design for 0.3 THz, 4 kW gyrotron for material processing application

The design of weakly tapered interaction cavity for 0.3 THz, 4 kW gyrotron operating at the fundamental cyclotron harmonic is presented in this paper. The interaction cavity design and the beam-wave interaction computation are carried out for TE_0,6 mode by using the Particle-in-Cell (PIC) electromagnetic simulation approach. The operating mode is selected by using the code GCOMS, in which various mode selection parameters and start oscillation current are calculated. Further, the power and frequency estimation are performed to finalize the cavity and electron beam parameters. The sensitivity analysis is done to finalize the tolerance limit in various parameters. Finally, the thermal and structural analyses are performed for the designed interaction cavity for the effective cooling.     

强流四杆型RFQ加速腔水冷系统的设计和数值模拟

为了研制一个强中子发生器，北京大学重离子物理研究所设计了一台高负载因子、高流强的RFQ加速器. 本文讨论了RFQ加速腔水冷系统的设计，使用有限元软件ANSYS对水冷系统进行了分析. 使用MAFIA模拟计算得到的功率密度，并将其作为ANSYS水冷模型的边界条件. 因为MAFIA程序和ANSYS程序分网方法的不同，使用一个程序来将MAFIA的结果导入到ANSYS模型中，从而建立起了RFQ加速腔的热分析模型. 通过这个热分析模型分析并检验了水冷系统的设计，确定了水冷系统的结构. 模拟计算结果表明：使用目前设计的这套水冷系统，能够使RFQ加速器工作在适宜的温度下以及长时间稳定的运行.     

The Design and Simulation of a Cooling System of High Current 4-rod RFQ Cavity

To develop a high current neutron generator, preliminary studies on a high current, high duty factor 4-rod RFQ accelerator has been carried out in the Institute of Heavy Ion Physics,Peking University. This paper discusses the design of a cooling system of the RFQ cavity. Finite element program ANSYS was used to analyze the cooling system. The power density was simulated by MAFIA and used as the boundary condition of ANSYS. Due to the different meshing methods between MAFIA and ANSYS, a program was written to transfer the result of MAFIA to ANSYS. Then a thermal analysis model of RFQ cavity was built by using ANSYS. The design of the cooling system was analyzed and checked by using this model, and then the structure of cooling system is determined. Simulation results showed that the design of the cooling system makes RFQ accelerator working at proper temperature and long time steadily.     

上海光源次谐波聚束器的优化设计及测试

 介绍了上海光源直线加速器499.654MHz次谐波聚束器的物理设计、结构、加工、微波测量和试验、运行等的情况。通过2维、3维电磁软件的数值模拟方法对腔型、结构尺寸、电磁参数、调谐范围进行了优化设计,现该腔已经加工完成,并对其进行了电参数测试,结果与物理设计指标吻合很好。在上海光源的束流指标调试过程中,该腔能长期稳定运行。     

HIRFL新B1聚束器频率微调系统的设计及稳定性分析

 频率自动调谐系统是聚束器的重要组成部分之一。频率调谐系统成功的研制和投入使用达到了使谐振腔体的固有谐振频率在22～54 MHz的范围内自动稳定在输入信号频率上的目的,频率自动微调系统达到了±5×10^-6的频率稳定度,解决了由于腔体失谐所造成的高频电压滑落的问题,由此在腔体的加速缝隙间得到稳定的高频电压,保证了聚束器系统的高质量可靠运行。     

Study of separated function radio frequency quadrupoles accelerator

SFRFQ (Separated Function Radio Frequency Quadrupoles) accelerator is a new post accelerator of RFQ (Radio Frequency Quadrupoles) type, which has been developed since the beginning of the 1990s at Peking University. In order to demonstrate the possibility of the SFRFQ, a prototype cavity has been designed.A special dynamics design method has been proposed to avoid the sparking problem and decrease the energy spread at the exit of SFRFQ. It consists of two aspects: the asymmetry structure design for transverse focusing and the inner buncher design for longitudinal bunching. This allows the improvement of the beam properties without increasing the cavity length. The simulation results show that the energy spread can be substantially reduced by using the inner buncher in the SFRFQ structure.     

中国散裂中子源RFQ的热分析

射频四级场(RFQ)加速器的水冷具有以下两种功用: 首先它可以把射频场发热带走, 维持RFQ腔的热稳定性及限制RFQ强体形变幅度; 其次, 当RFQ失谐时, 它还可以用来进行RFQ的调谐, 而同时又基本不影响RFQ的射频场分布. 由于RFQ粒子的传输效率对射频场的分布极其敏感, 在RFQ的运行中不再采用传统的用调谐器对RFQ进行调谐的方法. 本文通过热分析, 确定了RFQ加速器的水冷管道的数量和布局及最佳工作水温; 确定了RFQ失谐时, 如何利用水温变化来对RFQ进行调谐的方法.     

超重核研究谱仪的RFQ冷却聚束器RFQ1L

介绍了超重核研究谱仪中RFQ冷却聚束器RFQ1L的结构和运用SIMION程序对离子的冷却、聚束、引出和撇气过程的模拟情况。 模拟显示: 通过仔细选择工作点就完全可以把经过充气反冲质量分离器分离后的低品质束流转化为斑点小、发射度小和能量单一的高品质束流, 为紧接其后的磁铁和激光高效率分析提供条件。The structure and the simulation results about the cooling,bunching,extraction and skimming of the RFQ cooler and buncher RFQ1L, which is an important part of the being built super heavy nuclide research spectrometer, have been introduced. It shows that, by careful choice of its working point, we can obtain an ion beam with small beam spot, small emittance and mono energy, which can satisfy the requirements of the successive analyses by dipole and laser with high efficiencies.     

ITER���ΰ���ģ����ȹ�ˮ������Ӧ������

对ITER靠近中性束端口的标准屏蔽包层模块进行了热工水力与热应力计算与分析。首先用流体力学方法计算了两种导流管的阻力系数,然后通过合理简化计算了冷却管道系统的水力学,最后根据水力学的计算结果得到温度及应力的分布。分析结果表明,现有的屏蔽包层设计与旧的设计相比,能更有效地降低能量损失、提高冷却效率,满足设计要求。同时需要做局部改进,以确保安全运行。     

Optimum convective heat transfer coefficient for diode-pumped laser slabs

It is important for laser designers to study the characteristics of heat transfer from the laser crystal slab to the coolant in high-power DPSS laser operations. We have simulated and obtained the optimum heat transfer coefficient and coolant flow rate for our cavity design, in which the circulating coolant is maintained at a constant temperature. It has been determined that the coolant temperature and the convective heat transfer coefficient (h) are important parameters in the thermal analysis. The coefficient h is affected by the coolant flow rate, the physical properties of the laser slab and the coolant and the pumping cavity geometry. Using analytical heat transfer equation, for cooling water temperature of 300 K, the optimum flow rate for our cavity geometry is found to be 390 cm³/s, corresponding to h=5 W/cm² K.     

X射线干涉光刻偏转聚焦系统热载影响与分析

为缩短实验前的等待时间，减小热辐射对光学元件的损伤以及热变形对实验的影响，充分利用同步辐射X射线获得稳定有效的实验结果，对X射线干涉光刻(XIL)光束线偏转聚焦系统进行了热结构耦合分析。针对上海光源(SSRF)的光源参数，计算偏转聚焦系统所受的热功率密度分布，在此基础上对偏转聚焦系统在相同载荷、不同边界条件下进行了瞬态热平衡分析，得到双柱面镜M1、M2达到热平衡所需的时间、温度分布，并做了比较分析。结果表明，对XIL光束线上偏转聚焦系统的M1、M2采用间接水冷方式可削弱热载效应，达到热平衡的时间分别由8677 s和7850 s缩短到960 s和840 s，最高温度分别由182.73 ℃和129.73 ℃降低到57.94 ℃和47.29 ℃，此时的最大面形误差分别为7.23 μrad和9.24 μrad，缩短了从开机到实验的等待时间，在提高实验效率的同时能够获得稳定有效的实验结果。     

Low-temperature phase transitions in LiKSO4: A neutron study

A single crystal neutron diffraction study of the low temperature structural phase transitions in LiKSO₄ has been carried out. Detailed temperature dependence of the Bragg peak profiles and integrated intensities for a group of about 20 reflections has been investigated upon cooling and heating in the temperature range 300 K to 96 K. The crystal undergoes three clear phase transitions at 205 K (from sp. gr. P6₃ to sp. gr. P31c), at 189 K and at about 135 K on cooling. The corresponding temperatures are 250 K, 190 K and 138 K on the heating cycle. These transitions are extremely sluggish, the kinetics depending on the thermal treatment of the crystal.     

RFQ冷却聚束器研究简介

详细论述了RFQ冷却聚束器相关的基本原理,简单介绍了国际上此方面的研究和我们的工作。The radiofrequency quadrupole （RFQ） cooler and buncher has been developed in many laboratories to improve the secondary radioactive ion beam quality. In this paper, the principles of the RFQ constraint, buffer gas cooling, axial electric field and Paul trap are discussed in detail. The studies around the world and our work are also briefly introduced.     

Imaging of a convective field in a rectangular cavity using interferometry, schlieren and shadowgraph

The present study is concerned with the quantitative imaging of buoyancy-driven convection in a fluid medium that is confined in a horizontal differentially heated rectangular cavity. The horizontal surfaces of the cavity provide a temperature difference, for initiating convection in the fluid. The vertical side walls are thermally insulated. Three imaging techniques, namely laser interferometry, schlieren, and shadowgraph have been utilized. Experiments have been conducted in a cavity of length 447 mm and 32 mm vertical height. The cavity is square in cross-section, and the imaging direction is parallel to its longer side. Convection in air and water have been investigated. Temperature differences in the range of 5–50 K for air and 3–10 K for water have been employed in the experiments. Quantities of interest are the temperature profiles in unsteadiness in the thermal field. At lower temperature differences across the fluid region, temperatures as recorded by interferometry and schlieren are in good agreement with each other. Further, they match the numerical predictions, as well as correlations available in the literature. Imaging based on shadowgraph is not as satisfactory at lower temperature differences. At larger cavity temperature differences, the shadowgraph images become clear enough for quantitative analysis, but the flow becomes time-dependent. The three techniques reveal similar trends in terms of the spatial distribution of temperature gradients and the time scales of unsteadiness. The schlieren and shadowgraph are more suitable for high gradients and interferometry is suitable for low gradients and all these three techniques are not flow visualization tools alone but are appropriate for quantitative imaging of thermal field.     

高电压锯齿波聚束器的设计研制

近些年来,使用锯齿波直接形成的方法建造非谐振型聚束器在国内及国际均得到了广泛的应用。由于电子技术及机械加工工艺的飞速发展和更高功率电子管的出现,可以设计出更高指标的聚束器,进而可以有效提高束线的匹配效率及运行稳定度。对兰州重离子加速器源束线新的高电压锯齿波聚束器的研制进行了详细阐述,由于该聚束器具有目前国际同类型设备中最高的电压、频率以及相对苛刻的现场条件限制,故还对设计中所涉及的工程实施方案进行了有效补充和完善。