Magnetic anisotropy properties of CoZrNb thin films deposited on PET substrate by magnetron sputtering

Soft magnetism and magnetic anisotropy properties of CoZrNb thin films deposited on polyethylene terephthalate (PET) substrate by magnetron sputtering were investigated. As the film thickness increases, the coercivity of films decreases from 7 to 4 Oe. It exhibits an in-plane uniaxial magnetic anisotropy as the thickness of CoZrNb thin films increases. An easy axis is observed in CoZrNb films along the direction transverse to the rolling direction of the polymer web.     

Structural and magnetic properties of NiZn ferrite films with high saturation magnetization deposited by magnetron sputtering

NiZn ferrite films with well-defined spinel crystal structure were in situ fabricated by radio frequency magnetron sputtering at room temperature. The microstructures and static magnetic properties of the films’ dependence on the partial pressure ratio of argon to oxygen gas were investigated. Scanning electron microscope images indicated that all the films consisted of particles nanocrystalline in nature and the sizes increase as the ratio increases in the range of 10-25 nm. A large saturation magnetization (237.2 emu/cm³) and a minimum of coercivity (68 Oe) were obtained when the ferrite film was deposited in the ratio of 4:1. The complex permeability values (μ = μ′−iμ″) of the film were measured at frequency up to 5 GHz. It was shown that the film exhibited a large real part of permeability μ′ of 18 and a very high resonance frequency f_r of 1.2 GHz. The results suggested that the NiZn ferrite film as-deposited in the ratio of 4:1 may be promised as magnetic medium in the application of integrated circuits operating at microwave frequencies.     

Microstructure and magnetic properties studies of SmCo5 thin films grown on MgO and glass substrates

In this work, SmCo₅ thin films are deposited on single crystal MgO (1 0 0) and amorphous glass substrates with a Cr underlayer at 400 °C by sputtering. A comparison study shows that the microstructures and magnetic properties are different in the two SmCo₅ films on the MgO (1 0 0) and glass substrates, respectively. An epitaxial growth of Cr-(2 0 0)〈1 1 0〉/SmCo₅-(1 1 2¯ 0)〈0 0 0 1〉 is achieved on the MgO (1 0 0) single crystal substrate with an average grain size of 20 nm for SmCo₅. On the amorphous glass substrate, no significant crystallographic texture is found in the Cr underlayer. After the deposition of SmCo₅, a weak texture of (1 1 2¯ 0) is observed with an average grain size of 8 nm. High remanence ratio value in this film is probably due to strong exchange coupling. Both SmCo₅ films show high in-plane coercivity, high in-plane anisotropy and remanence enhancement.     

Stress and magnetic properties of surfaces and ultrathin films

Stress measurements with sub-monolayer sensitivity are performed to investigate the correlation between mechanical film stress and magneto-elastic anisotropy in epitaxial ferromagnetic monolayers. The magneto-elastic coupling B₁ of Fe(1 0 0) films is measured directly. Magnitude and sign of B₁ deviate from the respective bulk value. A strain-dependent correction of the magneto-elastic coupling coefficient B₁ describes the apparent thickness dependence of B₁ for film thicker than 10 nm. For thinner films, the possible contribution of surface corrections is discussed to explain the almost constant B₁. The implications of a modified magneto-elastic coupling for the anisotropy of ultrathin films is elucidated.     

Analyzing in-plane magnetic anisotropy from surface morphology for amorphous films

A method is developed to analyze the in-plane magnetic anisotropy from surface morphology for amorphous films. The lateral sizes along radial direction (R_RD) and tangent direction (R_TD) of rotational substrate, which are extracted from the surface morphology of Co_66.3Zr_33.7 amorphous films, are used to calculate stress anisotropy energy E_σ. It is found that E_σ is consistent with the magnetic anisotropy energy K_μ for the samples deposited on Si (1 0 0) substrate and then a relationship K_μ ∝ 1/R_RD − 1/R_TD can be obtained. This method is sensitive to the initial state of substrate so its application range is discussed.     

Nd-Fe-B/FeCo多层纳米复合膜的结构和磁性

制备了Nd₂₈Fe₆₆B₆/Fe₅₀Co₅₀多层纳米复合磁性薄膜，对溅射态和650℃退火处理15 min试样的相成分分析和微结构的观察显示，溅射态薄膜呈非晶态，经650℃退火处理15 min后，薄膜主要相成分为硬磁性Nd₂Fe₁₄B相和软磁性相FeCo(110)相.Nd₂Fe₁₄B相呈柱状，其易磁化c轴垂直于膜面，尺寸约10 nm.在硬磁性相和软磁性相之间存在少量富Nd相和非晶态，富Nd相大小约7 nm.磁性测量和分析表明，1)该系列薄膜退火态具有垂直于膜面的磁晶各向异性.2)对于固定厚度(10 nm)层Nd-Fe-B和不同厚度(t_FeCo=1—100 nm)层FeCo多层纳米复合膜,剩磁随软磁相FeCo 厚度的增加快速增加，而矫顽力则减小.当t_FeCo=5 nm时，最大磁能积达到200 kJ/m³. 3)硬磁相Nd-Fe-B层和软磁相FeCo层之间交换耦合导致剩磁和磁能积增强. 关键词： Nd-Fe-B/FeCo多层纳米复合膜 交换耦合 磁各向异性     

High frequency characteristics of NiO/(FeCo/NiO)10 multilayers with exchange anisotropy

[NiO/Fe₆₅Co₃₅]₁₀ exchange-coupled multilayer films for high frequency applications are fabricated, and their static magnetic property and microwave permeability are studied systematically. Both exchange bias field and ferromagnetic resonance frequency of the multilayers increase with decreasing Fe₆₅Co₃₅ thickness, which means that the microwave properties such as permeability and FMR frequency can be controlled by changing Fe₆₅Co₃₅ thickness in the exchange-coupled films. Ferromagnetic resonance frequencies beyond 7 GHz of the films are measured and reported for the first time.     

Origin of perpendicular magnetic anisotropy and evolution of magnetic domain structure of amorphous Pr-TM-B (TM=Fe, Co) films

In this study, the deposition pressure dependence of the compositional ratio, magnetic domain structure, and perpendicular magnetic anisotropy (PMA) of B-containing PrFe- and PrCo-based films, which are rare-earth-transition-metal (RE-TM) films, was investigated. PrFe- and PrCo-based films were fabricated by magnetron sputtering. The film compositions were controlled in a wide range by varying the deposition pressure. On the basis of experimental results, the residual stress of the films was considered to be the possible origin of their PMA. The films showed strong magneto-optical effects over the entire wavelength range of 300-750 nm. Because of the excellent magnetic and magneto-optical (MO) properties of the films, they have high potential for MO applications at wavelengths of red and blue lasers.     

Effects of the Hf content on the microstructure and magnetic properties of Co-Hf-Ta thin films

Effects of the Hf content in Co-Hf-Ta thin films on the microstructure and magnetic properties were investigated in this study. It was found that appropriate Hf addition can effectively refine the Co grain size. Co grain sizes sharply decreased from 50 nm down to 2.3 nm with increasing the Hf content from 1.02 at.% to 2.81 at.%, leading to the reduced magneto-crystalline anisotropy. The Co-Hf-Ta thin films with small Co grains reveal low anisotropy field, low coercivity, and high resistivity. By optimizing the Hf content, the film with Hf concentration of 2.81 at.% exhibits excellent soft magnetic properties: high saturation magnetization (4πM_S ∼ 13.6 kG), and low coercivity (H_C ∼ 0.6 Oe). The effective permeability of the film reaches 800 and remains constant up to 1 GHz.     

Morphology, magnetic, magnetoresistance and optical properties of Co-Ni-Mo alloys thin films

We present in this paper several results concerning the preparation by means of electrolysis and characterization of Co-Ni-Mo thin films. Co-Ni-Mo thin films with different molybdenum content in the range 0-25 at% Mo were prepared from a complex solution containing ions of Co, Ni and Mo, using galvanostatic control, on aluminum substrates. The effects of applied current density on the morphology, magnetic, magnetoresistance, and optical properties of the electrodeposited Co-Ni-Mo films were investigated. The applied current density significantly influenced the film composition and their magnetic properties. The increase of molybdenum content in Co-Ni films (up to 25 at% Mo) enhances the resistivity, but it reduces the magnetoresistance effect. We report the first observation of magnetoresistance as high as 8% in Co-Ni-Mo thin films.     

Influence of strain/stress on the nonlinear-optical properties of sprayed deposited ZnO:Al thin films

Nanocrystalline ZnO:Al thin films were deposited by reactive chemical pulverization spray pyrolysis technique on heated glass substrates at 450 °C to study their crystalline structure, composition, strain, stress, roughness characteristics and nonlinear optical susceptibility as a function of Al concentration (0, 2, 3, 5 at.%). The films were characterized by X-ray diffractometer (XRD), EDAX 9100 analyser, atomic force microscopy (AFM) and third harmonic generation (THG). The Al (3 at.%) doped ZnO thin films exhibited the lower strain/stress than undoped films. The nonlinear properties of the ZnO:Al thin films have been found to be influenced by the films strain/stress.     

Investigation of induced parallel magnetic anisotropy at low deposition temperature in Ba-hexaferrites thin films

In this paper we present the effect of low substrate temperature on structural, morphological, magnetic and optical properties of Ba-hexaferrite thin films. Films were deposited on single crystal Silicon (1 0 0) substrate employing the Pulsed Laser Deposition (PLD) technique. The structural, morphological, magnetic and optical properties are found to be strongly dependent on substrate temperature. The low substrate temperatures (room temperature to 200 °C) restrict the formation of larger grains. For the higher substrate temperature i.e., 400 °C, the grain size of the deposited thin film are much larger. The film grown at low substrate temperature do not show any anisotropy. As the substrate temperature is increased, the easy axis of the films alinged itself in the direction parallel to the film plane whereas the hard axis remained in the perpendicular direction. The higher substrate temperature caused the uniaxial magnetic anisotropy, which is very important in magnetic recording devices. The saturation magnetization and optical band gap energy values of 62 emu/cc and 1.75 eV, respectively, were achieved for the film of thickness 500 nm deposited at 400 °C. Higher values of coercivity, squareness and films thickness are associated with the growth of larger grains at higher substrate temperature.     

Microwave magnetic properties of soft magnetic thin films

We review our works that focus on the microwave magnetic properties of metallic,ferrite and granular thin films.Soft magnetic material with large permeability and low energy loss in the GHz range is a challenge for the inforcom technologies.GHz magnetic properties of the soft magnetic thin films with in-plane anisotropy were investigated.It is found that several hundreds of permeability at the GHz frequency was achieved for Co100-xZrx and Co90Nb10 metallic thin films because of their high saturation magneti...     

Multicolor photon emission from organic thin films on different substrates

Thin films of 1-pentyl-2^/,3^/-difluoro-3^///-methyl-4^////-octyl-p-quinquephenyl and 9,10-Bis (4-pentylphenylethynyl)antracene organic molecules were grown on optical glass, silicon and porous silicon substrates. First optical and luminescent properties of such hybrid composites are thoroughly studied using spectroscopic techniques. The strong decrease of aggregation in thin films of 1-pentyl-2^/,3^/-difluoro-3^///-methyl-4^////-octyl-p-quinquephenyl on porous silicon was observed. The possibility of simultaneous red, green and blue tunable photon emission from organic film/porous silicon hybrid structure is demonstrated.     

Thickness dependence of magnetic anisotropic properties of FeCoNd films

The magnetic FeCoNd films with thickness (t) from 50 to 166 nm were fabricated by RF magnetron co-sputtering at ambient condition. The amorphous structures of all of the films were investigated by X-ray diffraction and transmission electron microscopy. A spin reorientation transition from in-plane single domain state to out-of-plane stripe domain state was observed as a function of t. When t is below a critical thickness, magnetic moments lie in the film plane corresponding to in-plane single domain state because of the strong demagnetization energy. However, when t is increased, out-of-plane stripe domain structure was developed due to a dominated perpendicular magnetic anisotropy. Scanning electron microscopy data indicate that the perpendicular anisotropy, which is responsible for the formation of stripe domains, may result from the shape effect of the columnar growth of the FeCo grains.     

Magnetic anisotropy and electronic structure of iron films on W(1 1 0) by spin-polarized two-electron spectroscopy

Low-energy spin-polarized two-electron spectroscopy was applied to study the spin-dependent electronic structure of 3 ML and 50 ML epitaxial iron films grown on single crystal W(1 1 0). Such films are known to show an in-plane rotation of the easy magnetization axis between thicknesses [M. Donath, Journal of Physics: Condensed Matter 11 (48) (1999) 9421; D. Sander, Journal of Physics: Condensed Matter (20) (2004) R603, O. Fruchart, J.P. Nozieres, D. Givord, Journal of Magnetism and Magnetic Materials 207 (1999) 158, H.J. Elmers, U. Gradmann, Applied Physics A: Materials Science & Processing 51 (3) (1990) 255]. Momentum distributions of correlated electron pairs I(k₁, k₂) excited from the films by 25 eV primary electrons were measured for two opposite polarizations of the incident beam. Energy and momentum conservation laws in the electron scattering events allow the extraction of information on the spin-dependent Bloch spectral density function of the valence electrons in iron films. The observed difference in the electronic structure of these two films is most likely due to the different crystal structures of the films.     

Interface mediated control of microstructure and magnetic properties of FePt-C thin films

The microstructure and magnetic properties of FePt-C film deposited on the MgO/CrRu underlayer are studied in lieu of carbon doping in FePt and RF biasing assisted etching of the MgO underlayer. Increasing amounts of carbon doping in the FePt deteriorates the chemical ordering as a result of reduced kinetic energy of FePt adatoms due to frequent collision with carbon adatoms. This leads to a reduction in the magnetocrystalline anisotropy energy and hence the coercivity. RF etching of the MgO/CrRu underlayer before deposition of FePt helps to reduce the grain size and intergranular exchange interaction without adversely affecting the chemical ordering. Reduced intergranular exchange interaction leads to an increase in the coercivity.     

In-plane anisotropy and stress detection of films deposited by RC technique

A Novel Rotating Cryostat (RC) vacuum system originally designed to fabricate organic layers has been developed in order to prepare magnetic materials for specific applications such as sensors. The RC sputtering system has a rotating drum (substrate holder) and the possibility of using multi-port deposition sources. The source material sputtered by a dc magnetron, which was positioned one of the ports around the RC, was an iron disk (25 mm diameter, 0.8 mm thick, 99.8% pure). Results show that films have exhibited isotropic and anisotropic magnetisation at various running conditions of the RC using a Magneto-Optic Loop Plotter (MOKE) and a Vibrating Sample Magnetometer (VSM). Estimation of magnetic anisotropy confirms in-plane anisotropy in the films. Moreover, when these films are subjected to a bending stress within the VSM, they show chances in their hysteresis loops. These findings indicate a possible future for this technique to produce sensing devices for stress detection. Received 29 September 2001     

Sol-gel synthesis, characterization and optical properties of mercury-doped TiO2 thin films deposited on ITO glass substrates

The Hg-doped and undoped nano-crystalline TiO₂ films on ITO glass substrates surface and polycrystalline powders were prepared by sol-gel dip coating technique. The crystal structure and surface morphology of TiO₂ were characterized by means of X-ray diffractometer (XRD), atomic force microscope (AFM), spectrophotometer, Fourier-transform infrared (FTIR), and spectroscopic ellipsometry (SE). The results indicated that the powder of TiO₂, doped with 5% Hg in room temperature was only composed of the anatase phase whereas in the undoped powder exhibits an amorphous phase were present. After heat treatments of thin films, titanium oxide starts to crystallize at the annealing temperature 400 °C. The average crystallite size of the undoped TiO₂ films was about 8.17 nm and was increased with Hg-doping in the TiO₂ films. Moreover, the grains distributed more uniform and the surface roughness was greater in the Hg-doped TiO₂ films than in the undoped one. Refractive index and porosity were calculated from the measured transmittance spectrum. The values of the index of refraction are in the range (1.95-2.49) and the porosity is in the range (47-2.8). The coefficient of transmission varies from 60 to 90%. SE study was used to determine the annealing temperature effect on the optical properties in the wavelength range from 0.25 to 2 μm and the optical gap of the Hg-doped TiO₂ thin films.